LG Telematics Test Manual
[TG97AABJU]
Version 1.0 2011.04.15 LG Telematics Revision History Author Jongman Park Description Merged document. Document start Date April 15, 2011 LG Telematics Contents 1. How to Place a Call 2. ATT Tool for TCU Setting 3. VCP Commander FCC Information LG Telematics 1. How to Place a Call Fig.1 LG Telematics LG Telematics 2. ATT Tool for TCU Setting 1) Set COM Port 2) Check Connection Status Fig.2 LG Telematics 3) NAD Screen Fig.3 Fig.4 LG Telematics 4) Select Forced band mode and apply it Fig.5
- Click to see the selectable menu for changing
- After select the Service mode, click Control to apply it. LG Telematics 4) Check result of change. Fig.6 Fig.7 LG Telematics 3. VCP Commander 1) Run VCP-Commander.exe. This tool is single executable file. 2) Connect the named CAIT-port to Your PCs serial port. 3) Check the serial baud rate of VCP
(Power-up default is 38400bps) 4) select your PCs COM-port, Press Connect button 5) Test the right connection. Press END, verify that Status is Flipped (Cmd FAIL to Cmd OK) 6) Select command from drop-down-list And enter Value 1 or Value 2 according to each command. 7) Press SET button, then status is flipped. 8) Below table are command lists, value 1 and value 2. Command PREF_AUTOMATIC PREF_CELL_ONLY PREF_PCS_ONLY PREF_CDMA_ONLY PREF_ANALOG_ONLY PREF_HOME_ONLY PREF_P_REV_3 PREF_P_REV_4 PREF_P_REV_6 A_KEY Value 1 Value 2 Description Dont care Dont care Set system selection mode Dont care Dont care Set MOB_P_REV temporally See example 1 See example 1 Set A-key value LG Telematics PREF_FOR_RC IMSI_MCC Dont care Dont care Set NV_PREF_FOR_RC_I Set NV_IMSI_MCC_I 1 ~5 3-digit Decimal ie 120 2-digit Decimal ie 12 One-byte decimal 0 ~ 7 IMSI_11_12 SCM SLOT_SYCLE_INDEX Dont care MOB_TERM_HOME 0 or 1 MOB_TERM_FOR_SID 0 or 1 MOB_TERM_FOR_NID 0 or 1 Dial_SO2_LB, Dial_SO3_EVRC, Dial_SO9_LB13, Dial_SO54 Dial_SO55_LB Dial_SO32768 Dial_SO32798 Dial_SO32799 CALL_ANSWER CALL_END Power_Down Dont care Dont care Dont care Dont care Set NV_IMSI_11_12_I
(MNC) Dont care Set NV_SCM_I Dont care Dont care Dont care Dont care Dont care Dont care Dont care Dont care Set NV_SLOT_CYCLE_INDEX_I Enable(1) or Disable(0) Enable(1) or Disable(0) Enable(1) or Disable(0) Originate call with specified SO. Dial number is fixed to 111 internally. Answer incoming call End call. Force power-down Communication Module only After this command, must do unplug then plug main VCP power to power-up Module. Force power-recycle Communication Module only Power_Recycle Dont care Dont care LG Telematics FCC Information FCC part 15.19 This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions: (1) this device ma not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Installation This unit should only be installed by qualified personnel by GMOnstar. Address P.O.Box 430627 Pontiac, MI 48343 Part 15.21 statement
"Change or Modifications that are not expressly approved by the manufacturer could void the user's authority to operate the equipment.
"In order to comply with RF Exposure requirements the antenna or radiating element of this device must be installed to ensure that it is at least 20cm from end users. The antenna supplied with this device must not exceed a maximum gain of 9.74dBi in the cellular band and 8.25dBi in the PCS band."
Part 15.105 statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Part 15 Class B Compliance This device and its accessories comply with part15 of FCC rules. Operation is subject to the following two conditions: