all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Users Manual | Users Manual | 2.73 MiB | August 10 2009 | |||
1 | Cover Letter(s) | August 10 2009 / September 10 2009 | ||||||
1 | Cover Letter(s) | August 10 2009 / September 10 2009 | ||||||
1 | External Photos | August 10 2009 | ||||||
1 | Internal Photos | August 10 2009 | ||||||
1 | ID Label/Location Info | August 10 2009 / September 10 2009 | ||||||
1 | Test Report | August 10 2009 / September 10 2009 | ||||||
1 | Test Setup Photos | August 10 2009 / September 10 2009 |
1 | Users Manual | Users Manual | 2.73 MiB | August 10 2009 |
Order Number Test Report Number
: GETEC-C1-09-192
: GETEC-E3-09-108 FCC Class B Certification Page 1 / 1 APPENDIX G
: USERS MANUAL EUT Type: LCD TV/Monitor FCC ID.: BEJ42LH260HUA LCD TV OWNERS MANUAL 32LH240H 32LH250H 37LH250H 32LH255H 37LH255H 42LH255H 37LH260H 42LH260H please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attched on the back cover and quote this information to your dealer when you require service. Model:
Serial:
This product qualifies for ENERGY STAR in the factory default
(Home Use) setting. Changing the factory default settings or enabling other fea-
tures may increase power consumption that could exceed the limits necessary to quality for ENERGY STAR. 1-800-243-0000 USA, Consumer User 1-888-865-3026 USA, Commercial User 1-888-542-2623 CANADA LG Customer Information Center P/NO : SAC34026002 (0908-REV02) www.lgcommercial.com WARNING / CAUTION WARNING / CAUTION To prevent fire or shock hazards, do not expose this product to rain or moisture. FCC NOTICE Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two condi-
tions: (1) This device may not cause (harmful) interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (of the device). Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. CAUTION Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the users authority to operate this product 1 TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING/CAUTION TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. NOTE TO CABLE/TV INSTALLER This reminder is provided to call the CATV system installers attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. 6 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 1 2 Do not use this apparatus near water. Clean only with dry cloth. 7 Only use attachments/accessories specified by the manufacturer. 3 Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers)that produce heat. 9 Unplug this apparatus during lighting storms or when unused for long periods of time. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 4 5 2 Never touch this apparatus or antenna during a thunder or lighting storm. 15 WARNING - To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles or expose the TV to direct air conditioning. 11 12 13 14 When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV. Do not allow an impact shock or any objects to fall into the product, and do not drop onto the screen with something. CAUTION concerning the Power Cord :
It is recommend that appliances be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not connect too many appliances to the same AC power outlet as this could result in fire or elec-
tric shock. Do not overload wall outlets. Overloaded wall out-
lets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Do not make the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV. 16 Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit). 17 GGRROOUUNNDDIINNGG Ensure that you connect the earth ground wire to prevent possible electric shock. (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grouned AC outlet) If grounding methods are not possible, have a qualified electri-
cian install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Power Supply Short-circuit Breaker 18 DDIISSCCOONNNNEECCTTIINNGG DDEEVVIICCEE FFRROOMM MMAAIINNSS Mains plug is the disconnecting device. The plug must remain readily operable. 3 19 AANNTTEENNNNAASS OOuuttddoooorr aanntteennnnaa ggrroouunnddiinngg If an outdoor antenna is installed, follow the precau-
tions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to pro-
vide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to prop-
er grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna dis-
charge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding elec-
trode. AAnntteennnnaa ggrroouunnddiinngg aaccccoorrddiinngg ttoo tthhee NNaattiioonnaall EElleeccttrriiccaall CCooddee,, AANNSSII//NNFFPPAA 7700 Ground Clamp Antenna Lead in Wire Electric Service Equipment NEC: National Electrical Code Antenna Discharge Unit
(NEC Section 810-20) Grounding Conductors
(NEC Section 810-21) Ground Clamps Power Service Grounding Electrode System (NEC Art 250, Part H) 20 21 Cleaning When cleaning, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemi-
cals such as alcohol, thinners or benzene. Moving Make sure the product is turned off, unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV. 22 23 Ventilation Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other mate-
rials (e.g.) plastic while plugged in. Do not install in excessively dusty places. If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord contact an authorized service center. 24 Do not press strongly upon the panel with a hand or sharp object such as nail, pencil or pen, or make a scratch on it. 25 26 Keep the product away from direct sunlight. FFoorr LLCCDD TTVV If the TV feels cold to the touch, there may be a small flicker when it is turned on. This is normal, there is nothing wrong with TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary dis-
tortion effects on the screen. ON DISPOSAL
(Only Hg lamp used LCD TV) The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. 4 CONTENTS WARNING / CAUTION . 1 SAFETY INSTRUCTIONS . 2 FEATURES OF THIS TV . 7 PREPARATION Accessories . 8 Front Panel Information . 9 Back Panel Information . 10 Stand Instruction . 12 VESA Wall Mounting . 14 Cable Management . 15 Desktop Pedestal Installation . 16 Swivel Stand . 16 Attaching the TV to a desk . 17 Securing the TV to the wall to prevent falling When the TV is used on a stand . 18 Antenna or Cable Connection . 19 USB Entry Modes . 43 Photo List . 45 Music List . 49 PICTURE CONTROL Picture Size (Aspect Ratio) Control . 52 Preset Picture Settings
- Picture Mode - Preset . 54
- Color Tone Preset . 55 Manual Picture Adjustment - User Mode . 56 Picture Improvement Technology . 57 Advanced Control - Black (Darkness) Level . 58 Advanced Control - Eye Care . 59 Advanced Control - Film Mode . 60 Picture Reset . 61 Demo mode . 61 EXTERNAL EQUIPMENT SETUP SOUND & LANGUAGE CONTROL HD Receiver Setup . 20 DVD Setup . 23 VCR Setup . 25 Other A/V Source Setup . 26 PC Setup . 27 USB Connection . 33 WATCHING TV / CHANNEL CONTROL Remote Control Functions . 34 Turning On TV . 36 Channel Selection . 36 Volume Adjustment . 36 On-Screen Menus Selection . 37 Channel Setup
- Auto Scan (Auto Tuning) . 38
- Add / Delete Channel (Manual Tuning) . 39
- Channel Editing . 40 Channel Label . 41 Input List . 42 Auto Volume Leveler (Auto Volume) . 62 Preset Sound Settings (Sound Mode) . 63 Sound Setting Adjustment - User Mode . 64
- SRS TruSurround XT . 65 Clear Voice . 66 Balance . 67 TV Speakers On/Off Setup . 68 Audio Reset . 69 Stereo/SAP Broadcast Setup . 70 Audio Language . 71 On-Screen Menus Language Selection . 72 Caption Mode
- Analog Broadcasting System Captions . 73
- Digital Broadcasting System Captions . 74
- Caption Option . 75 TIME SETTING Clock Setting
- Auto Clock Setup . 76
- Manual Clock Setup . 77 Auto On/Off Time Setting . 78 Sleep Timer Setting . 79 5 PARENTAL CONTROL / RATINGS Set Password & Lock System . 80 Channel Blocking . 83 Movie & TV Rating . 84 Downloadable Rating . 87 External Input Blocking . 88 APPENDIX Troubleshooting . 89 Maintenance . 91 Product Specifications . 91 IR Codes . 92 Open Source License . 94 6 FEATURES OF THIS TV HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC."
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. View videos and photos and listen to music on your TV through USB 2.0 (videos dependent on model). High-definition television. High-resolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions. LG TV include a unique invisible speaker system, tuned by renowned audio expert, Mr. Mark Levinson. Speakers are embedded in strategic spots behind the front cabinet and use minute vibrations to turn the entire front bezel into the speaker system. The result is a clean, polished look, and enhanced audio by increasing the sweet spot, giving a wider and richer sound field. is a trademark of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc. Automatically enhances and amplifies the sound of human voice frequency range to help keep dialogue audible when background noise swells. Matches the original frame rate of the film for a more film-like experience IMPORTANT INFORMATION TO PREVENT IMAGE BURN
/ BURN-IN ON YOUR TV SCREEN When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV for an extended period, it can become permanently imprinted on the screen. This phenomenon is known as image burn or burn-in. Image burn is not covered under the manufacturers warranty. In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period
(2 or more hours for LCD, 1 or more hours for Plasma). Image burn can also occur on the letterboxed areas of your TV if you use the 4:3 aspect ratio setting for an extended period. 7 PREPERATION ACCESSORIES Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. The accessories included may differ from the images below. 35 6 7 8 LIS T 0 9 V O L M U T E C H P A G E E NTE R R E T U R N FLASHBK TIM E R M A R K R ATIO P O W E R 1 IN P U T 4 2 C C 7 5 3 LIS T 8 6 0 9 V O L M U T E C H P A G E E NTE R M E N U FLASHBK 1.5V 1.5V R E T U R N A L A M S A P Owners Manual CD Manual EJECT Remote Control, Batteries Power Cord Not included with all models OOppttiioonn EExxttrraass
* Wipe spots on the exterior only with the polishing cloth.
* Do not wipe roughly when removing stain. Excessive pressure may cause scratch or discoloration. Polishing Cloth When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain standards compliance. D-sub 15 pin Cable x 4 x 2 Bolts for stand assembly
(Refer to P.12) Torx plus Star head screw
(Refer to P.12) Screw for stand fixing
(Refer to P.17) Protection Cover
(Refer to P.13) Protective Bracket and Bolt for Power Cord
(This feature is not available for all models.)
(Refer to P.15) Cable Holder
(Refer to P.15) Plug in type holder
(Refer to P.15) 8 FRONT PANEL INFORMATION Image shown may differ from your TV. SPEAKER Remote Control Sensor, Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the TV is switched on. CH VOL ENTER MENU INPUT CHANNEL (DD,EE) Buttons VOLUME (+, -) Buttons ENTER Button MENU Button INPUT Button POWER Button P R E P A R A T O N I 9 PREPARATION BACK PANEL INFORMATION Image shown may differ from your TV. R 15 P R E P A R A T O N I ANTENNA IN ANTENNA IN M.P.I.M.P.I. 13 14 12 N I B S U R I O D U A O N O M L
O E D V I AV IN 2 2 32/37/42LH250H, 32/37/42LH255H, 37/42LH260H 2 7 10 GAME CONTROL 1 AV IN 1 VIDEO AUDIO 4 L(MONO) R
( ) RESET UPDATE RGB IN (PC) RJP L VIDEO COMPONENT IN R AUDIO 2 1 AUDIO IN
(RGB/DVI)
/DVI IN 3 SPEAKER OUT
(8 ) REMOTE CONTROL OUT RS-232C IN
(SERVICE ONLY) 32LH240H 5 6 2 AV IN 1 VIDEO AUDIO 4 9 7 8 TV - LINK CFG 11 10 L(MONO) R RESET UPDATE RGB IN (PC) RJP L VIDEO COMPONENT IN R AUDIO 2 1 AUDIO IN
(RGB/DVI)
/DVI IN 8 3 SPEAKER OUT
(8 ) REMOTE CONTROL OUT RS-232C IN
(SERVICE ONLY) 5 6 9 10 R R 1 2 3 4 5 6 7 GAME CONTROL Control port 10 RJP (REMOTE JACK PACK PORT) Connect to remote jack pack control output port. 11 12 13 14 15 TV - LINK CFG Used for FTG Configuration USB IN Used for viewing photos and listening to MP3s. ANTENNA IN Connect over-the air signals to this jack. M.P. I. Control port. Power Cord Socket For operation with AC power. Caution: Never attempt to operate the TV on DC power. AV (Audio/Video) IN Analog composite connection. Supports standard definition video only (480i). Used for PC/DTV audio input jack. COMPONENT IN Analog Connection. Supports HD. Uses a red, green, and blue cable for video & a red and white cable for audio. HDMI/DVI IN Digital Connection. Supports HD video and Digital audio. Accepts DVI video using an adapter or HDMI to DVI cable (not included) SPEAKER OUT 8 Connect to external speaker input. REMOTE CONTROL OUT IR output for controlling an auxiliary device. UPDATE Enables/disables software downloads and debug mode. RESET Performs a hardware reset. 8 RGB IN (PC) Analog PC Connection. Uses a D-sub 15 pin cable
(VGA cable). AUDIO IN (RGB/DVI) 1/8 headphone jack for analog PC audio input. 9 RS-232C IN (SERVICE ONLY) Used for software updates. P R E P A R A T O N I 11 PREPARATION STAND INSTRUCTION Image shown may differ from your TV. INSTALLATION 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 2 Assemble the TV as shown. 3 x 4 Tighten the stand with the four screws (provided as parts of the TV). or x 2 x 2 Tighten the two of these four screws and the two Torx plus star head screws (provided as parts of the TV) to secure the TV. Tighten the two Torx plus star head screws with a star head driver bit (not provided as parts of the TV).
NOTE GG When assembling the desk type stand, make sure the bolt is fully tightened (If not tightened fully, the TV can tilt forward after the product installa-
tion). Do not over tighten. P R E P A R A T O N I 12 DETACHMENT 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 2 Loose the bolts from TV. 3 Detach the stand from TV. PROTECTION COVER After removing the stand, install the included pprrootteeccttiioonn ccoovveerr over the hole for the stand. Press the PPRROOTTEECCTTIIOONN CCOOVVEERR into the TV until you hear it click. P R E P A R A T O N I 13 PREPARATION VESA WALL MOUNTING Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest installer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. We recommend that you use an LG brand wall mount when mounting the TV to a wall. LG recommends that wall mounting be performed by a qualified professional installer. Model VESA (A * B) AA BB Standard Screw Quantity Wall Mounting Bracket
(sold separately) 200 * 100 M4 200 * 200 M6 4 4 RW230 AW-47LG30M AW-47LG30M 32LH240H, 32LH250H, 32LH255H 37LH250H, 37LH255H, 37LH260H, 42LH250H, 42LH255H, 42LH260H
NOTE GG Screw length needed depends on the wall mount used. For further information, refer to the instruc-
tions included with the mount. GG Standard dimensions for wall mount kits are shown in the table. GG When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided. GG Do not use screws longer then the standard dimen-
sion, as they may cause damage to the inside to the TV. GG For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on their specifica-
tions. GG Do not use screws that do not comply with the VESA standard screw specifications. Do not use fasten the screws too strongly, this may damage the TV or cause the TV to a fall, leading to personal injury. LG is not liable for these kinds of accidents. GG LG is not liable for TV damage or personal injury when a non-VESA or non specified wall mount is used or the consumer fails to follow the TV installa-
tion instructions. CAUTION GG Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric shock. P R E P A R A T O N I 14 CABLE MANAGEMENT Image shown may differ from your TV. 1 Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. Secure the power cable with the PPROTECTIVE BRACKET/Screw or the Plug in type Holder. It will help prevent the power cable from being removed by accident. 3 Put the cables inside the CABLE MANAGEMENT CLIP and snap it closed. PROTECTIVE BRACKET/Screw
(This feature is not available for all models.) Or PLUG IN TYPE HOLDER NOTE
GG Do not hold the CABLE MANAGEMENT CLIP when moving the TV.
- If the TV is dropped, you may be injured or the product may be broken. GG With some TVs, the PLUG IN TYPE HOLDER and the CABLE HOLDER are included. If these holders are inserted into the hole provided on back of the TV, they cannot be removed. 2 Install the CABLE MANAGEMENT CLIP as shown. If your TV has the CABLE HOLDER, install it as shown and bundle the cables. CABLE MANAGEMENT CLIP CABLE HOLDER P R E P A R A T O N I 15 PREPARATION DESKTOP PEDESTAL INSTALLATION Image shown may differ from your TV. For proper ventilation, allow a clearance of 4 inches on all four sides from the wall. 4 inches 4 inches 4 inches 4 inches CAUTION GG Ensure adequate ventilation by following the clearance recommendations. GG Do not mount near or above any type of heat source. SWIVEL STAND After installing the TV, you can adjust the TV set manually to the left or right direction by 90 degrees to suit your viewing position. P R E P A R A T O N I 16 ATTACHING THE TV TO A DESK Image shown may differ from your TV. The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Stand 4-Screws
(not provided as parts of the product) GG Screw: M5 x L (*L: Table depth + 8~10 mm) ex) Table depth: 15mm, Screw: M5 x 25 Desk Stand Desk 1-Screw
(provided as parts of the product) WARNING GG To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury. P R E P A R A T O N I 17 PREPARATION SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount). Image shown may differ from your TV. We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children dont climb on or hang from the TV. P R E P A R A T O N I Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely. Use a sturdy rope (sold separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product. NOTE
GG Use a platform or cabinet strong enough and large enough to support the size and weight of the TV. GG To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same. 18 To prevent damage do not connect to the power outlet until all connections are made between the devices. ANTENNA OR CABLE CONNECTION 1. Antenna (Analog or Digital) Wall Antenna Socket or Outdoor Antenna without a Cable Box Connection. For optimum picture quality, adjust the direction if needed. Wall Antenna Socket Outdoor Antenna
(VHF, UHF) 2. Cable Cable TV Wall Jack Multi-family Dwellings/Apartments
(Connect to wall antenna socket) ANTENNA IN ANTENNA IN M.P.I. RF Coaxial Wire (75 ohm) Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna) Copper Wire Be careful not to bend the copper wire when connecting the antenna. ANTENNA IN ANTENNA IN M.P.I. RF Coaxial Wire (75 ohm) To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. If the antenna needs to be split for two TVs, install a 2-Way Signal Splitter. If the antenna is not installed properly, contact your dealer for assistance. P R E P A R A T O N I 19 EXTERNAL EQUIPMENT SETUP To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment. Image shown may differ from your TV. HD RECEIVER SETUP This TV can receive Digital Over-the-air or Digital Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. Component Connection 1. How to connect 1 Connect the video outputs (Y, PB, PR) of the digital set-
top box to the CCOOMMPPOONNEENNTT IINN VVIIDDEEOO jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red). 2 Connect the audio output of the digital set-top box to the CCOOMMPPOONNEENNTT IINN AAUUDDIIOO jacks on the TV. 2. How to use Turn on the digital set-top box.
(Refer to the owners manual for the digital set-top box.) Select CCoommppoonneenntt input source using the IINNPPUUTT button on the remote control. Supported Resolutions Y, CB/PB, CR/PR Y PB PR L R 1 2 GAME CONTROL AV IN 1 VIDEO AUDIO L(MONO) R R 2 1 L AUDIO VIDEO COMPONENT IN
/DVI IN SPEAKER OUT REMOT CONTROL
(8 ) Signal 480i 480p 720p 1080i 1080p Component HDMI Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) Yes Yes Yes Yes Yes No Yes Yes Yes Yes 720x480i 720x480p 1280x720p 1920x1080i 1920x1080p 15.73 15.73 31.47 31.50 44.96 45.00 33.72 33.75 67.432 67.50 27.00 26.97 33.75 33.71 59.94 60.00 59.94 60.00 59.94 60.00 59.94 60.00 59.94 60.00 24.00 23.976 30.00 29.97 P R E P A R A T O N I 20 HDMI Connection 1. How to connect 1 2 Connect the digital set-top box to HHDDMMII //DDVVII IINN 11 or HHDDMMII 22 jack on the TV. No separate audio connection is necessary. HDMI supports both audio and video. 2. How to use Turn on the digital set-top box.
(Refer to the owners manual for the digital set-top box.) Select HHDDMMII11 or HHDDMMII22 input source with using the IINNPPUUTT button on the remote control. AV IN 1 VIDEO AUDIO L(MONO) R L EO MPONENT IN R AUDIO 2 1 RESET UPDATE RGB IN (PC) AUDIO IN
(RGB/DVI)
/DVI IN RS-232C IN
(SERVICE ONLY) SPEAKER OUT 8(8 ) REMOTE CONTROL OUT 1 HDMI OUTPUT HDMI-DTV Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 720x480p 1280x720p 1920x1080i 1920x1080p 31.47 31.47 44.96 45.00 33.72 33.75 67.432 67.50 27.00 26.97 33.75 33.71 59.94 60.00 59.94 60.00 59.94 60.00 59.939 60.00 24.00 23.976 30.00 29.97 E X T E R N A L E Q U I P M E N T S E T U P 21 EXTERNAL EQUIPMENT SETUP DVI to HDMI Connection 1. How to connect 1 2 Connect the DVI output of the digital set-top box to the HHDDMMII//DDVVII IINN 11 jack on the TV. Connect the audio output of the digital set-top box to the AAUUDDIIOO IINN ((RRGGBB//DDVVII)) jack on the TV. GAME ONTROL AV IN 1 VIDEO AUDIO L(MONO) R L VIDEO COMPONENT IN R AUDIO 2 1 RGB IN (PC) AUDIO IN
(RGB/DVI)
/DVI IN RS-232C IN
(SERVICE ONLY) SPEAKER OUT
(8 ) REMOTE CONTROL OUT 2. How to use 1 2 Turn on the digital set-top box. (Refer to the owners man-
ual for the digital set-top box.) Select the HHDDMMII11 input source on the TV using the IINNPPUUTT button on the remote control.
NOTE GG A DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio, so a separate audio connection is necessary. DVI OUTPUT L R AUDIO E X T E R N A L E Q U I P M E N T S E T U P 22 DVD SETUP Component Connection 1. How to connect 1 2 Connect the video outputs (Y, PB, PR) of the DVD to the CCOOMMPPOONNEENNTT IINN VVIIDDEEOO jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red). Y PB PR L R Connect the audio outputs of the DVD to the CCOOMMPPOONNEENNTT IINN AAUUDDIIOO jacks on the TV. 2. How to use Turn on the DVD player, insert a DVD. Select the CCoommppoonneenntt input source on the TV using the IINNPPUUTT button on the remote control. Refer to the DVD player's manual for operating instructions. 1 GAME CONTROL 2 AV IN 1 VIDEO AUDIO L(MONO) R R 2 1 L AUDIO VIDEO COMPONENT IN R
/DVI IN SPEAKER OUT REMOTE CONTROL O
(8 ) Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV Video output ports on DVD player Y Y Y Y Y PB PB B-Y Cb Pb PR PR R-Y Cr Pr E X T E R N A L E Q U I P M E N T S E T U P 23 EXTERNAL EQUIPMENT SETUP Composite (RCA) Connection 1. How to connect 1 Connect the AAUUDDIIOO/VVIIDDEEOO jacks between TV and DVD. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red). 2. How to use Turn on the DVD player, insert a DVD. Select the or AA VV 11 input source on the TV using the IINNPPUUTT button on the remote control. If connected to AAVV IINN 22, select AAVV22 input source on the TV. Refer to the DVD player's manual for operating instructions. HDMI Connection 1. How to connect 1 2 Connect the HDMI output of the DVD to the HHDDMMII//DDVVII IINN 11 or HHDDMMII 22 jack on the TV. No separate audio connection is necessary. HDMI supports both audio and video. 2. How to use Select the HHDDMMII11 or HHDDMMII22 input source on the TV using the IINNPPUUTT button on the remote control. Refer to the DVD player's manual for operating instructions. E X T E R N A L E Q U I P M E N T S E T U P 24 GAME CONTROL AV IN 1 VIDEO AUDIO L(MONO) R L VIDEO COMPONENT IN R AUDIO 2 1 RE A
(R
/DVI IN SPEAKER OUT REMOTE
(8 ) CONTROL OU 1 VIDEO L R AUDIO OL AV IN 1 VIDEO AUDIO L(MONO) R L DEO OMPONENT IN R AUDIO 2 1 RESET UPDATE RGB IN (PC) AUDIO IN
(RGB/DVI)
/DVI IN RS-232C IN
(SERVICE ONLY) SPEAKER OUT
(8 ) REMOTE CONTROL OUT 1 HDMI OUTPUT VCR SETUP Antenna Connection 1. How to connect 1 2 Connect the RF antenna out socket of the VCR to the AANNTTEENNNNAA IINN socket on the TV. Connect the antenna cable to the RF antenna in socket of the VCR. 2. How to use Set VCR output switch to 3 or 4 and then tune TV to the same channel number. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.) Composite (RCA) Connection 1. How to connect 1 Connect the AAUUDDIIOO/VVIIDDEEOO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red) 2. How to use Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.) Select the AA VV 11 input source on the TV using the IINNPPUUTT button on the remote control. If connected to AAVV IINN 22, select AAVV22 input source on the TV. NOTE
GG If you have a mono VCR, connect the audio cable from the VCR to the AAUUDDIIOO ((LL//MMOONNOO)) jack of the TV. ANTENNA IN M.P.I. S-VIDEO VIDEO L R ANT OUT 1 OUTPUT SWITCH ANT IN Wall Jack 2 Antenna GAME CONTROL AV IN VIDEO AUDIO L(MONO) R L VIDEO COMPONENT IN R AUDIO 2 1 1
/DVI IN
( ) ANT IN S-VIDEO VIDEO L R AUDIO ANT OUT OUTPUT SWITCH E X T E R N A L E Q U I P M E N T S E T U P 25 EXTERNAL EQUIPMENT SETUP OTHER A/V SOURCE SETUP 1. How to connect Camcorder Video Game Set VIDEO L R 1 N I B S U R I O D U A O N O M L
O E D V I AV IN 2 1 Connect the AAUUDDIIOO/VVIIDDEEOO jacks between TV and external equipment. Match the jack colors.
(Video = yellow, Audio Left = white, and Audio Right = red) 2. How to use Select the AAVV22 input source on the TV using the IINNPPUUTT button on the remote control. If connected to AAVV IINN 11 input, select the AA VV 11 input source on the TV. Operate the corresponding external equipment. E X T E R N A L E Q U I P M E N T S E T U P 26 PC SETUP This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. VGA (D-Sub 15 pin) Connection 1. How to connect 1 2 Connect the VGA output of the PC to the RRGGBB IINN
((PP CC)) jack on the TV. Connect the PC audio output to the AAUUDDIIOO
((RRGGBB//DDVVII)) jack on the TV. IINN 2. How to use Turn on the PC and the TV. Select the RRGGBB--PPCC input source on the TV using the IINNPPUUTT button on the remote control. O R R O 2 1 RESET UPDATE RGB IN (PC) AUDIO IN
(RGB/DVI)
/DVI IN RS-232C IN
(SERVICE ONLY) SPEAKER OUT
(8 ) REMOTE CONTROL OUT 2 1 AUDIO RGB OUTPUT E X T E R N A L E Q U I P M E N T S E T U P DVI to HDMI Connection 1. How to connect 1 2 Connect the DVI output of the PC to the HHDDMMII//DDVVII IINN 11 jack on the TV. Connect the PC audio output to the AAUUDDIIOO II NN
((RRGGBB//DDVVII)) jack on the TV. AV IN 1 VIDEO AUDIO L(MONO) R L VIDEO COMPONENT IN R AUDIO 2 1 RESET UPDATE RGB IN (PC) AUDIO IN
(RGB/DVI)
/DVI IN RS-232C IN
(SERVICE ONLY) SPEAKER OUT
(8 ) REMOTE CONTROL OUT 2. How to use Turn on the PC and the TV. Select the HHDDMMII11 input source on the TV using the IINNPPUUTT button on the remote control. 1 2 DVI OUTPUT AUDIO 27 EXTERNAL EQUIPMENT SETUP Supported Display Specifications
(RGB-PC, HDMI-PC) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 640x350 31.469 640x480 720x400 800x600 31.469 31.469 37.879 1024x768 48.363 1280x768 1360x768 1366x768 47.776 47.720 47.13 70.08 59.94 70.08 60.31 60.00 59.87 59.799 59.65 640x350 640x480 720x400 800x600 1024x768 1280x768 1360x768 31.468 31.469 31.469 35.156 37.879 48.363 56.476 47.776 47.712 1280x1024 63.981 1600x1200 75.00 1920x1080 66.587 70.09 59.9 70.08 56.25 60.31 60.00 70.06 59.870 60.015 60.020 60.00 59.934
(For 37/42LH260H)
NOTES GG To get the best picture quality, adjust the PC graphics card to 1360x768, 60Hz. GG Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use. GG In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear. When you use too long RGB-PC cable, there might be a noise on the screen. GG Avoid keeping a fixed image on the screen for a long period of time. The fixed image could become per-
manently imprinted on the screen. GG The synchronization input form for Horizontal and Vertical frequencies is separate. GG Depending on the graphics card, some resolution settings may not allow the image to be positioned on the screen properly. E X T E R N A L E Q U I P M E N T S E T U P 28 USB CONNECTION or 1 Memory Key N I B S U I R O D U A O N O M L
O E D V I AV IN 2 1. How to connect 1 Connect the USB device to the UUSSBB II NN jack on the side of TV. 2. How to use After connecting the UUSSBB II NN jack, you use the USB func-
tion. (GG pp..4433) E X T E R N A L E Q U I P M E N T S E T U P 33 USB Image shown may differ from your TV. ENTRY MODES When you connect a USB device, this pop up menu is displayed automatically. When the Pop Up menu does not appear, you can select Photo List or Music List in the USB menu. On a USB device, you can not add a new folder or delete an existing folder. 1 Connect the USB device to the UUSSBB IINN jacks on the side of TV. This TV Supports on JPG and MP3. When removing the USB device Press the device. EJECT button before removing the USB or Memory Key Select PPHHOOTTOO LLIISSTT or MMUUSSIICC LL II SS TT. PHOTO LIST MUSIC LIST N I B S U R 2 3 ENTER U S B 43 Precautions when using the USB device GG Only a USB storage device is recognizable. GG If the USB storage device is connected through a USB hub, the device is not recognizable. GG A USB storage device using an automatic recognition program may not be recognized. GG A USB storage device which uses its own driver may not be recognized. GG The recognition speed of a USB storage device may depend on each device. GG In case of a card reader, up to four memory cards are concurrently recognizable. GG Please do not turn off the TV or unplug the USB device when the connected USB storage device is working. When such device is suddenly separated or unplugged, the stored files or the USB storage device may be dam-
aged. U S B GG Only use a USB storage device which has normal music, image or movie files. GG Please connect power to a USB storage device (over 0.5A) which requires an external power supply. If not, the device may not be recognized. GG Please connect a USB storage device with cable is offered by USB maker. If connected with cable is not offered by USB maker or an excessively long cable, the device may not be recognized. GG Some USB storage devices may not be supported or operate properly. GG File alignment method of USB storage device is similar to Window XP and filename can recognize up to 100 English characters. GG Please backup important files because data on the USB device may be damaged. Data management is the con-
sumer's responsibility and as a result, the manufacturer does not cover data damage. GG Please use only a USB storage device which was formatted as a FAT32, NTFS file system provided with the Windows operating system. In case of a storage device formatted as a different utility programme which is not supported by Windows, it may not be recognized. GG Data in a USB storage device cannot be deleted in the NTFS file system. GG If your USB memory device has multiple partitions, or if you use a USB multi-card reader, you can use up to 4 partitions or USB memory devices. GG The recommended capacity is 1TB or less for a USB external hard disk and 32GB or less for USB memory. GG Any device with more than the recommended capacity may not work properly. GG If a USB external hard disk with a "Energy Saving" function does not work, turn the hard disk off and on again to make it work properly. Refer to the user manual of the application USB external hard disk. GG When using a USB HDD via the USB extensing cable, connect a support electric power source. 44 APPENDIX TROUBLESHOOTING TThhee ooppeerraattiioonn ddooeess nnoott wwoorrkk nnoorrmmaallllyy.. The remote control doesnt work Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the TV. Ensure that the batteries are installed with correct polarity (+ to +, - to -). Ensure that the correct remote operating mode is set: TV, VCR etc. Install new batteries.
*This feature is not available for all models. Power is suddenly turned off Is the sleep timer set?
Check the power control settings. Power interrupted. TV will be automatically turned off, in case of no signal for 15 minutes. TThhee vviiddeeoo ddooeess nnoott wwoorrkk.. No picture &No sound Check whether the product is turned on. Try another channel. The problem may be with the broadcast. Is the power cord inserted into wall power outlet?
Check your antenna direction and/or location. Test the wall power outlet, plug another products power cord into the outlet where the products power cord was plugged in. Picture appears slowly after switching on This is normal, the image is muted during the product startup process. Please contact your service center, if the picture has not appeared after five minutes. No or poor color or poor picture Horizontal/vertical bars or picture shaking Adjust Color in menu option. Keep a sufficient distance between the product and the VCR. Try another channel. The problem may be with the broadcast. Are the video cables installed properly?
Activate any function to restore the brightness of the picture. Check for local interference such as an electrical appliance or power tool. Poor reception on some channels Station or cable product experiencing problems, tune to another station. Station signal is weak, reorient antenna to receive weaker station. Check for sources of possible interference. Lines or streaks in pictures No picture when connecting HDMI Check antenna (Change the direction of the antenna). Check HDMI cable over version 1.3. The HDMI cables dont support HDMI version 1.3, it cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3. A P P E N D I X 89 APPENDIX TThhee aauuddiioo ddooeess nnoott wwoorrkk.. Picture OK & No sound Press the VOL or VOLUME button. Sound muted? Press MUTE button. Try another channel. The problem may be with the broadcast. Are the audio cables installed properly?
No output from one of the speakers Adjust Balance in menu option. Unusual sound from inside the product A change in ambient humidity or temperature may result in an unusual noise when the product is turned on or off and does not indicate a fault with the product. No sound when connecting HDMI or USB Check HDMI cable over version 1.3. Check USB cable over version 2.0. Use normal MP3 file. TThheerree iiss aa pprroobblleemm iinn PPCC mmooddee.. ((OOnnllyy PPCC mmooddee aapppplliieedd))
*This feature is not available for all models. The signal is out of range Adjust resolution, horizontal frequency, or vertical frequency. Check the input source. Vertical bar or stripe on background &
Horizontal Noise &
Incorrect position Work the Auto configure or adjust clock, phase, or H/V position. (Option) Screen color is unstable or single color Check the signal cable. Reinstall the PC video card. PPoowweerr No Power See troubleshooting flow chart. EErrrraattiicc OOppeerraattiioonn Installer menu setup Adjust Installer menu settings as required. SSooffttwwaarree PPrroobblleemmss Cannot direct enter chan-
nel number or No Signal appears After 2-5-5 + MENU, only channels included in TV controller will appear. If chan-
nel is available it can be added to channel scan, rescan channels. If it is not avail-
able, the No Signal message appears on the TV screen. NOTE
GG For other problems not caused by the TV, refer to other devices operating guides. A P P E N D I X 90 MAINTENANCE Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can enjoy your new TV. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen 1 2 Heres a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until its almost dry, and then use it to wipe the screen. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV. WARNING GG Do not use window/glass cleaner or anything with ammonia to clean the screen. Cleaning the Cabinet To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth. Extended Absence CAUTION GG If you expect to leave your TV dormant for a long time (such as a vacation), its a good idea to unplug the power cord to protect against possible damage from lightning or power surges. PRODUCT SPECIFICATIONS MODEL Dimensions
(Width x Height x Depth) Weight With stand Without stand With stand Without stand Power requirement Television System Program Coverage External Antenna Impedance Environment condition Operating Temperature Operating Humidity Storage Temperature Storage Humidity 32LH240H (32LH240H-UA) 32LH250H (32LH250H-UA) 32LH255H (32LH255H-UA) 31.6 x 22.9 x 8.8 inches 805.0 x 583.0 x 223.8 mm 37LH250H (37LH250H-UA) 37LH255H (37LH255H-UA) 37LH260H (37LH260H-UA) 36.2 x 25.9 x 11.6 inches 922.0 x 659.0 x 297.0 mm 42LH250H (42LH250H-UA) 42LH255H (42LH255H-UA) 42LH260H (42LH260H-UA) 40.4 x 28.1 x 11.6 inches 1028.0 x 715.4 x 297.0 mm 31.6 x 20.7 x 4.2 inches 805.0 x 528.2 x 108.9 mm 36.2 x 23.4 x 3.4 inches 922.0 x 595.0 x 88.0 mm 40.4 x 25.7 x 3.4 inches 1028.0 x 655.0 x 88.7 mm 27.7 pounds / 12.6 kg 25.1 pounds / 11.4 kg 33.0 pounds / 15.0 kg 29.1 pounds / 13.2 kg 41.0 pounds / 18.6 kg 37.0 pounds / 16.8 kg AC100-240V ~ 50/60Hz NTSC-M, ATSC, 64 & 256 QAM VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135 75 ohm 32 ~ 104F (0 ~ 40C) Less than 80%
-4 ~ 140F (-20 ~ 60C) Less than 85%
The specifications shown above may be changed without prior notice for quality improvement. A P P E N D I X 91 APPENDIX IR CODES 1. How to Connect Connect your wired remote control to the Remote Control port on the TV. 2. Remote Control IR Codes Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz Tc T1 Carrier frequency FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3 Configuration of frame 1st frame Lead code Low custom code High custom code Data code Data code C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 Repeat frame Lead code Repeat code BBiitt ddeessccrriippttiioonn Bit 0 Repeat code Tf 9 ms 4.5 ms 0.55 ms 9 ms 2.25 ms 0.56 ms 1.12 ms Bit 1 0.56 ms 2.24 ms FFrraammee iinntteerrvvaall:: TTff The waveform is transmitted as long as a key is depressed. Tf Tf Tf=108ms @455KHz A P P E N D I X 92 Code
(Hexa) Function Note Code
(Hexa) Function Note Remote control Button (Power On/Off) D6 TV 08 0B 1E 79 39 POWER INPUT MARK RATIO CC Remote control Button Remote control Button Remote control Button Remote control Button 10-19 Number Key 0-9 Remote control Button 4C 1A 02 03 00 01 0A 0E 09 43 5B E8 CA 40 41 07 06 44 72 71 63 61 8F 8E
- (Dash)/LIST Remote control Button FLASHBK Remote control Button VOL +
VOL -
CH CH SAP TIMER MUTE MENU Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button RETURN Remote control Button ALAM EJECT ENTER RED Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button A (GREEN) Remote control Button G (YELLOW) Remote control Button ll ll (BLUE) Remote control Button FF GG Remote control Button Remote control Button 5A D0 BF D5 CE CC 76 77 AF C4 C5 AV1 AV2 Discrete IR Code
(TV Input Selection) Discrete IR Code
(AV1 Input Selection) Discrete IR Code
(AV2 Input Selection) COMPONENT Discrete IR Code
(COMPONENT Input Selection) RGB-PC HDMI1 HDMI2 Ratio 4:3 Ratio 16:9 Ratio Zoom POWER ON POWER OFF Discrete IR Code
(RGB Input Selection) Discrete IR Code
(HDMI1 Input Selection) Discrete IR Code
(HDMI2 Input Selection) Discrete IR Code
(Only 4:3 Mode) Discrete IR Code
(Only 16:9 Mode) Discrete IR Code
(Only Zoom1 Mode) Discrete IR Code
(Only Power On) Discrete IR Code
(Only Power Off) A P P E N D I X 93 OPEN SOURCE LICENSE GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all. Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software - to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some other free software foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps: (1) copyright the soft-
ware, and (2) offer you this license which gives you legal permis-
sion to copy, distribute and/or modify the software. Also, for each author's protection and ours, we want to make cer-
tain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. The precise terms and conditions for copying, distribution and modification follow. GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This license applies to any program or other work which con-
tains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The
"Program", below, refers to any such program or work, and a
"work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work con-
taining the Program or a portion of it, either verbatim or with modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you". Activities other than copying, distribution and modification are not covered by this license; they are outside its scope. The act of running the Program is not restricted, and the out-
put from the program is covered only if its contents constitute a work based on the program (independent of having been made by running the program). Whether that is true depends on what the program does. 1. You may copy and distribute verbatim copies of the program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this license and to the absence of any warranty; and give any other recipients of the program a copy of this license along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of section 1 above, provided that you also meet all of these conditions:
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. 94 b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part there of, to be licensed as a whole at no charge to all third parties under the terms of this license. c) If the modified program normally reads commands interac-
tively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this license.
(Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this license, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the dis-
tribution of the whole must be on the terms of this license, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or con-
test your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the program. In addition, mere aggregation of another work not based on the program with the Program (or with a work based on the program) on a volume of a storage or distribution medium does not bring the other work under the scope of this license. 3. You may copy and distribute the program (or a work based on it, under section 2) in object code or executable form under the terms of sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-
readable source code, which must be distributed under the terms of sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alter-
native is allowed only for noncommercial distribution and only if you received the program in object code or exe-
cutable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all mod-
ules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offer-
ing access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this license. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this license. However, parties who have received copies, or rights, from you under this license will not have their licens-
es terminated so long as such parties remain in full compli-
ance. 5. You are not required to accept this license, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this license. Therefore, by modifying or distributing the program
(or any work based on the program), you indicate your accep-
tance of this license to do so, and all its terms and conditions for copying, distributing or modifying the program or works based on it. 6. Each time you redistribute the program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforc-
ing compliance by third parties to this license. 95 APPENDIX 7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the con-
ditions of this license, they do not excuse you from the con-
ditions of this license. If you cannot distribute so as to satis-
fy simultaneously your obligations under this license and any other pertinent obligations, then as a consequence you may not distribute the program at all. For example, if a patent license would not permit royalty-free redistribution of the program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this license would be to refrain entirely from distribution of the program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest valid-
ity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution sys-
tem, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this license. 8. If the distribution and/or use of the program is restricted in certain countries either by patents or by copyrighted inter-
faces, the original copyright holder who places the program under this license may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this license incorporates the limitation as if written in the body of this license. 9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present ver-
sion, but may differ in detail to address new problems or con-
cerns. Each version is given a distinguishing version number. If the program specifies a version number of this license which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of A P P E N D I X 96 any later version published by the Free Software Foundation. If the program does not specify a version number of this license, you may choose any version ever published by the Free Software Foundation. 10.If you wish to incorporate parts of the program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copy-
righted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of pro-
moting the sharing and reuse of software generally. NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLD-
ERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRO-
GRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUS-
TAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS How to apply these terms to your new programs If you develop a new program, and you want it to be of the great-
est possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effective-
ly convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found. one line to give the program's name and a brief idea of what it does. Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the license, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
POSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type show w. This is free software, and you are welcome to redistribute it under certain conditions; type show c for details. The hypothetical commands show w and show c should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than show w and show c; they could even be mouse-clicks or menu items-whatever suits your program. You should also get your employer (if you work as a programmer) or your school, if any, to sign a copyright disclaimer for the pro-
gram, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the pro-
gram Gnomovision (which makes passes at compilers) written by James Hacker. signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice This General Public License does not permit incorporating your program into proprietary programs. If your program is a subrou-
tine library, you may consider it more useful to permit linking pro-
prietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this license. A P P E N D I X 97 GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, ver-
sion 2, hence the version number 2.1.]
Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software - to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some specially designated software packages - typically libraries - of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think careful-
ly about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below. When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free soft-
ware (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things. To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights. We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library. To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is mod-
ified by someone else and passed on, the recipients should know that what they have is not the original version, so that the origi-
nal author's reputation will not be affected by problems that might be introduced by others. Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company can-
not effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license. Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to per-
mit linking those libraries into non-free programs. When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software devel-
opers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license pro-
vides advantages in certain special circumstances. For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License. In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system. 98 Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this license and to the absence of any warranty; and distribute a copy of this license along with the Library. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library". The former contains code derived from the library, whereas the latter must be combined with the library in order to run. GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This license agreement applies to any software library or other program which contains a notice placed by the copyright hold-
er or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called this license). Each license is addressed as "you". A library means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables. The Library, below, refers to any such software library or work which has been distributed under these terms. A work based on the Library means either the Library or any derivative work under copyright law: that is to say, a work containing the library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language.
(Hereinafter, translation is included without limitation in the term modification.) Source code for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it con-
tains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this license; they are outside its scope. The act of running a program using the Library is not restrict-
ed, and output from such a program is covered only if its con-
tents constitute a work based on the library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the library does and what the program that uses the library does. 1. You may copy and distribute verbatim copies of the library's complete source code as you receive it, in any medium, pro-
vided that you conspicuously and appropriately publish on You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of section 1 above, provided that you also meet all of these conditions:
a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this license. d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any appli-
cation-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the library, and can be reasonably considered independent and separate works in themselves, then this license, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the library, the dis-
tribution of the whole must be on the terms of this license, whose permissions for other licenses extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or con-
test your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the library. In addition, mere aggregation of another work not based on the library with the library (or with a work based on the library) on a volume of a storage or distribution medium does not bring the other work under the scope of this license. 99 3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the library into a program that is not a library. 4. You may copy and distribute the library (or a portion or deriv-
ative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-
readable source code, which must be distributed under the terms of sections 1 and 2 above on a medium customarily used for software interchange. If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code. 5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a work that uses the Library. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this license. However, linking a work that uses the library with the Library creates an executable that is a derivative of the Library
(because it contains portions of the library), rather than a work that uses the library. The executable is therefore cov-
ered by this license. Section 6 states terms for distribution of such executable. When a work that uses the library uses material from a head-
er file that is part of the library, the object code for the work may be a derivative work of the library even though the source code is not. Whether this is true is especially significant if the work can be linked without the library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law. If such an object file uses only numerical parameters, data structure layouts and accessories, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legal-
ly a derivative work. (Executable containing this object code plus portions of the library will still fall under Section 6.) Otherwise, if the work is a derivative of the library, you may distribute the object code for the work under the terms of Section 6. Any executable containing that work also fall under Section 6, whether or not they are linked directly with the library itself. 6. As an exception to the sections above, you may also combine or link a "work that uses the library" with the library to pro-
duce a work containing portions of the library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications. You must give prominent notice with each copy of the work that the library is used in it and that the Library and its use are covered by this license. You must supply a copy of this license. If the work during execution displays copyright notices, you must include the copyright notice for the library among them, as well as a reference directing the user to the copy of this license. Also, you must do one of these things:
a) Accompany the work with the complete corresponding machine-readable source code for the library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable work that uses the Library, as object code and/or source code, so that the user can modify the library and then relink to produce a modified executable containing the modified library. (It is understood that the user who changes the contents of definitions files in the library will not necessarily be able to recompile the appli-
cation to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the users computer system, rather than copying library functions into the exe-
cutable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with. c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6, above, for a charge no more than the cost of performing this distribution. d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place. e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy. 100 For an executable, the required form of the "work that uses the library" must include any data and utility programs need-
ed for reproducing the executable from it. However, as a spe-
cial exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the exe-
cutable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normal-
ly accompany the operating system. Such a contradiction means you cannot use both them and the library together in an executable that you distribute. 7. You may place library facilities that are a work based on the library side-by-side in a single library together with other library facilities not covered by this license, and distribute such a combined library, provided that the separate distribu-
tion of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things:
a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the sections above. b) Give prominent notice with the combined library of the fact that part of it is a work based on the library, and explaining where to find the accompanying uncombined form of the same work. 8. You may not copy, modify, sublicense, link with, or distribute the library except as expressly provided under this license. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the library is void, and will automatically termi-
nate your rights under this license. However, parties who have received copies, or rights, from you under this license will not have their licenses terminated so long as such parties remain in full compliance. 9. You are not required to accept this license, since you have not signed it. However, nothing else grants you permission to mod-
ify or distribute the library or its derivative works. These actions are prohibited by law if you do not accept this license. Therefore, by modifying or distributing the library (or any work based on the library), you indicate your acceptance of this license to do so, and all its terms and conditions for copying, distributing or modifying the library or works based on it. 10.Each time you redistribute the library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or mod-
ify the library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this license. 11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the con-
ditions of this license, they do not excuse you from the con-
ditions of this license. If you cannot distribute so as to satis-
fy simultaneously your obligations under this license and any other pertinent obligations, then as a consequence you may not distribute the library at all. For example, if a patent license would not permit royalty-free redistribution of the library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this license would be to refrain entirely from distribution of the library. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest valid-
ity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution sys-
tem which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a license cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this license. 12.If the distribution and/or use of the library is restricted in cer-
tain countries either by patents or by copyrighted interfaces, the original copyright holder who places the library under this license may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this license incorporates the limitation as if written in the body of this license. 13.The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the library specifies a version number of this license which applies to it and any later version, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. 101 To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the copyright line and a pointer to where the full notice is found. one line to give the library's name and a brief idea of what it does. Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the license, or (at your option) any later version. This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
POSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Also add information on how to contact you by electronic and paper mail. You should also get your employer (if you work as a programmer) or your school, if any, to sign a copyright disclaimer for the library, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the library Frob (a library for tweaking knobs) written by James Random Hacker. signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice If the library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14.If you wish to incorporate parts of the library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make excep-
tions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 15.BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLD-
ERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUS-
TAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS How to apply these terms to your new libraries If you develop a new library, and you want it to be of the great-
est possible use to the public, we recommend making it free soft-
ware that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). 102 MOZILLA PUBLIC LICENSE Version 1.1
1.Definitions. 1.0.1. Commercial use means distribution or otherwise making the covered code available to a third party. 1.1. Contributor means each entity that creates or con-
tributes to the creation of modifications. 1.2. 1.3. 1.4. Contributor version means the combination of the orig-
inal code, prior modifications used by a contributor, and the modifications made by that particular contributor. Covered code means the original code or modifications or the combination of the original code and modifications, in each case including portions thereof. Electronic distribution mechanism means a mechanism generally accepted in the software development communi-
ty for the electronic transfer of data. 1.5. Executable means covered code in any form other than source code. 1.6. 1.7. Initial developer means the individual or entity identified as the initial Developer in the Source Code notice required by exhibit A. Larger work means a work which combines covered code or portions thereof with code not governed by the terms of this License. 1.8. License means this document. 1.8.1. Licensable means having the right to grant, to the maxi-
mum extent possible, whether at the time of the initial grant or subsequently acquired, any and all of the rights conveyed herein. 1.9. Modifications means any addition to or deletion from the substance or structure of either the original code or any previous modifications. When covered code is released as a series of files, a modification is:
A. Any addition to or deletion from the contents of a file containing original code or previous modifications. B. Any new file that contains any part of the original code or previous modifications. 1.10. Original code means source code of computer software code which is described in the source code notice required by exhibit as original code, and which, at the time of its release under this license is not already covered code governed by this license. 1.10.1.Patent claims means any patent claim(s), now owned or hereafter acquired, including without limitation, method, process, and apparatus claims, in any patent licensable by grantor. 1.11. Source code means the preferred form of the covered code for making modifications to it, including all modules it contains, plus any associated interface definition files, scripts used to control compilation and installation of an executable, or source code differential comparisons against either the original code or another well known, available covered code of the contributor's choice. The source code can be in a compressed or archival form, pro-
vided the appropriate decompression or de-archiving soft-
ware is widely available for no charge. 1.12. You (or Your) means an individual or a legal entity exercising rights under, and complying with all of the terms of, this license or a future version of this license issued under section 6.1. For legal entities, You includes any entity which controls, is controlled by, or is under common control with You. For purposes of this definition, control means (a) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (b) own-
ership of more than fifty percent (50%) of the outstand-
ing shares or beneficial ownership of such entity. 2. Source Code License. 2.1. The initial developer grant. The initial developer hereby grants You a world-wide, roy-
alty-free, non-exclusive license, subject to third party intel-
lectual property claims:
a) under intellectual property rights (other than patent or trademark) licensable by initial developer to use, repro-
duce, modify, display, perform, sublicense and distrib-
ute the original code (or portions thereof) with or with-
out modifications, and/or as part of a larger work; and
(b) under patents claims infringed by the making, using or selling of original code, to make, have made, use, prac-
tice, sell, and offer for sale, and/or otherwise dispose of the original code (or portions there of). 103
(c) the licenses granted in this section 2.1(a) and (b) are effective on the date Initial developer first distributes original code under the terms of this license.
(d) Notwithstanding section 2.1(b) above, no patent license is granted: 1) for code that You delete from the original Code; 2) separate from the original code; or 3) for infringements caused by: i) the modification of the original code or ii) the combination of the original code with other software or devices. 2.2. Contributor Grant. Subject to third party intellectual property claims, each contributor hereby grants You a world-wide, royalty-free, non-exclusive license
(a) under intellectual property rights (other than patent or trademark) licensable by contributor, to use, reproduce, modify, display, perform, sublicense and distribute the modifications created by such contribu-
tor (or portions thereof) either on an unmodified basis, with other modifications, as covered code and/or as part of a larger work; and
(b) under patent claims infringed by the making, using, or selling of modifications made by that contributor either alone and/or in combination with its contributor version (or portions of such combination), to make, use, sell, offer for sale, have made, and/or otherwise dispose of: 1) modifications made by that contributor
(or portions thereof); and 2) the combination of mod-
ifications made by that contributor with its contributor version (or portions of such combination).
(c) the licenses granted in sections 2.2(a) and 2.2(b) are effective on the date contributor first makes commer-
cial use of the covered code.
(d) Notwithstanding section 2.2(b) above, no patent license is granted: 1) for any code that contributor has deleted from the contributor version; 2) separate from the contributor version; 3) for infringements caused by: i) third party modifications of contributor version or ii) the combination of modifications made by that contributor with other software (except as part of the contributor version) or other devices; or 4) under patent claims infringed by covered code in the absence of modifications made by that contributor. 3. Distribution Obligations. 3.1. Application of license. The modifications which You create or to which you con-
tribute are governed by the terms of this license, including without limitation section 2.2. The source code version of covered code may be distributed only under the terms of this license or a future version of this license released under section 6.1, and you must include a copy of this license with every copy of the source code you distribute. You may not offer or impose any terms on any source code version that alters or restricts the applicable version of this license or the recipients' rights hereunder. However, you may include an additional document offering the additional rights described in section 3.5. 3.2. Availability of source code. Any modification which you create or to which you con-
tribute must be made available in source code form under the terms of this license either on the same media as an executable version or via an accepted electronic distribu-
tion mechanism to anyone to whom you made an exe-
cutable version available; and if made available via elec-
tronic distribution mechanism, must remain available for at least twelve (12) months after the date it initially became available, or at least six (6) months after a subsequent version of that particular modification has been made available to such recipients. You are responsible for ensur-
ing that the source code version remains available even if the electronic distribution mechanism is maintained by a third party. 3.3. Description of modifications. 3.4. You must cause all covered code to which you contribute to contain a file documenting the changes You made to create that covered code and the date of any change. You must include a prominent statement that the modification is derived, directly or indirectly, from original code provided by the initial developer and including the name of the initial developer in (a) the source code, and (b) in any notice in an executable version or related documentation in which you describe the origin or ownership of the covered code. Intellectual property matters
(a) Third party claims. If contributor has knowledge that a license under a third party's intellectual property rights is required to exercise the rights granted by such contributor under sections 2.1 or 2.2, contributor must include a text file with the source code distribution titled "LEGAL" which describes the claim and the party making the claim in sufficient detail that a recipient will know whom to contact. If contributor obtains such knowledge after the modification is made available as described in section 3.2, contributor shall promptly modi-
fy the LEGAL file in all copies contributor makes available thereafter and shall take other steps (such as notifying appropriate mailing lists or newsgroups) reasonably calcu-
lated to inform those who received the covered code that new knowledge has been obtained.
(b) Contributor APIs. If contributor's modifications include an application programming interface and contributor has knowledge of patent licenses which are reasonably necessary to implement that API, contributor must also include this information in the LEGAL file. 104
(c) Representations. contributor represents that, except as disclosed pursuant to section 3.4(a) above, contributor believes that contributor's modifications are contributor's original creation(s) and/or contributor has sufficient rights to grant the rights conveyed by this license. 3.7. Larger works. You may create a larger work by combining covered code with other code not governed by the terms of this license and distribute the larger work as a single product. In such a case, you must make sure the requirements of this license are fulfilled for the covered code. 3.5. Required notices. 4. Inability to comply due to statute or regulation. You must duplicate the notice in exhibit A in each file of the source code. If it is not possible to put such notice in a particular source code file due to its structure, then You must include such notice in a location (such as a relevant directory) where a user would be likely to look for such a notice. If You created one or more modification(s), you may add your name as a contributor to the notice described in exhibit A. you must also duplicate this license in any documentation for the source code where You describe recipients' rights or ownership rights relating to covered code. You may choose to offer, and to charge a fee for, warranty, support, indemnity or liability obligations to one or more recipients of covered code. However, you may do so only on your own behalf, and not on behalf of the Initial developer or any contributor. You must make it absolutely clear than any such warranty, support, indemni-
ty or liability obligation is offered by you alone, and You hereby agree to indemnify the Initial developer and every contributor for any liability incurred by the Initial develop-
er or such contributor as a result of warranty, support, indemnity or liability terms you offer. 3.6. Distribution of executable versions. You may distribute covered code in executable form only if the requirements of section 3.1-3.5 have been met for that covered code, and if you include a notice stating that the source code version of the covered code is available under the terms of this license, including a description of how and where you have fulfilled the obligations of section 3.2. The notice must be conspicuously included in any notice in an executable version, related documentation or collateral in which you describe recipients' rights relating to the covered code. You may distribute the executable version of covered code or ownership rights under a license of your choice, which may contain terms different from this license, provided that you are in compliance with the terms of this license and that the license for the exe-
cutable version does not attempt to limit or alter the recip-
ient's rights in the source code version from the rights set forth in this license. If you distribute the executable ver-
sion under a different license you must make it absolutely clear that any terms which differ from this license are offered by you alone, not by the Initial developer or any contributor. You hereby agree to indemnify the initial developer and every contributor for any liability incurred by the initial developer or such contributor as a result of any such terms You offer. If it is impossible for you to comply with any of the terms of this license with respect to some or all of the covered code due to statute, judicial order, or regulation then you must: (a) comply with the terms of this license to the max-
imum extent possible; and (b) describe the limitations and the code they affect. Such description must be included in the LEGAL file described in section 3.4 and must be included with all distributions of the source code. Except to the extent prohibited by statute or regulation, such description must be sufficiently detailed for a recipient of ordinary skill to be able to understand it. 5. Application of this license. This license applies to code to which the initial developer has attached the notice in exhibit A and to related covered code. 6. Versions of the license. 6.1. New versions. Netscape communications corporation (Netscape) may publish revised and/or new versions of the license from time to time. Each version will be given a distinguishing version number. 6.2. Effect of new versions. Once covered code has been published under a particular version of the license, you may always continue to use it under the terms of that version. You may also choose to use such covered code under the terms of any subsequent version of the license published by netscape. No one other than netscape has the right to modify the terms applicable to covered code created under this license. 6.3. Derivative works. If You create or use a modified version of this license
(which you may only do in order to apply it to code which is not already covered code governed by this license), You must (a) rename Your license so that the phrases
"Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL",
"NPL" or any confusingly similar phrase do not appear in your license (except to note that your license differs from this license) and (b) otherwise make it clear that Your version of the license contains terms which differ from the Mozilla Public license and netscape Public License. (Filling in the name of the initial developer, original code or con-
tributor in the notice described in exhibit A shall not of themselves be deemed to be modifications of this license.) 105 7. DISCLAIMER OF WARRANTY. COVERED CODE IS PROVIDED UNDER THIS LICENSE ON AN AS IS BASIS, WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES THAT THE COV-
ERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR NON-INFRINGING. THE ENTIRE RISK AS TO THE QUALITY AND PERFOR-
MANCE OF THE COVERED CODE IS WITH YOU. SHOULD ANY COVERED CODE PROVE DEFECTIVE IN ANY RESPECT, YOU (NOT THE INITIAL DEVELOPER OR ANY OTHER CONTRIBUTOR) ASSUME THE COST OF ANY NECESSARY SERVICING, REPAIR OR CORRECTION. THIS DISCLAIMER OF WARRANTY CONSTITUTES AN ESSENTIAL PART OF THIS LICENSE. NO USE OF ANY COVERED CODE IS AUTHORIZED HEREUNDER EXCEPT UNDER THIS DISCLAIMER. 8. TERMINATION. 8.1. This license and the rights granted hereunder will terminate automatically if you fail to comply with terms herein and fail to cure such breach within 30 days of becoming aware of the breach. All sublicenses to the covered code which are properly granted shall survive any termination of this license. Provisions which, by their nature, must remain in effect beyond the termination of this license shall survive. 8.2. If you initiate litigation by asserting a patent infringement claim (excluding declatory judgment actions) against ini-
tial developer or a contributor (the initial developer or contributor against whom you file such action is referred to as Participant) alleging that:
(a) such participant's contributor version directly or indi-
rectly infringes any patent, then any and all rights granted by such participant to you under sections 2.1 and/or 2.2 of this license shall, upon 60 days notice from Participant terminate prospectively, unless if within 60 days after receipt of notice you either: (i) agree in writing to pay participant a mutually agreeable reasonable royalty for your past and future use of modifications made by such participant, or (ii) withdraw your litigation claim with respect to the contributor version against such participant. If within 60 days of notice, a reasonable royalty and payment arrangement are not mutually agreed upon in writing by the parties or the litigation claim is not withdrawn, the rights granted by partici-
pant to you under sections 2.1 and/or 2.2 automati-
cally terminate at the expiration of the 60 day notice period specified above.
(b) any software, hardware, or device, other than such par-
ticipant's contributor Version, directly or indirectly infringes any patent, then any rights granted to You by such participant under sections 2.1(b) and 2.2(b) are revoked effective as of the date you first made, used, sold, distributed, or had made, modifications made by that participant. 8.3. If you assert a patent infringement claim against partici-
pant alleging that such participant's contributor version directly or indirectly infringes any patent where such claim is resolved (such as by license or settlement) prior to the initiation of patent infringement litigation, then the rea-
sonable value of the licenses granted by such participant under sections 2.1 or 2.2 shall be taken into account in determining the amount or value of any payment or license. 8.4. In the event of termination under sections 8.1 or 8.2 above, all end user license agreements (excluding distributors and resellers) which have been validly granted by you or any distributor hereunder prior to termination shall survive termination. 9. LIMITATION OF LIABILITY. UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY, WHETHER TORT (INCLUDING NEGLIGENCE), CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY DIS-
TRIBUTOR OF COVERED CODE,OR ANY SUPPLIER OF ANY OF SUCH PARTIES, BE LIABLE TO ANY PERSON FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUEN-
TIAL DAMAGES OF ANY CHARACTER INCLUDING, WITH-
OUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNC-
TION, OR ANY AND ALL OTHER COMMERCIAL DAM-
AGES OR LOSSES, EVEN IF SUCH PARTY SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAM-
AGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLY TO LIABILITY FOR DEATH OR PERSONAL INJURY RESULT-
ING FROM SUCH PARTY'S NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH LIMITATION. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAM-
AGES, SO THIS EXCLUSION AND LIMITATION MAY NOT APPLY TO YOU. 10. U.S. GOVERNMENT END USERS. The covered code is a "commercial item," as that term is defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of
"commercial computer software" and "commercial computer software documentation," as such terms are used in 48 C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4
(June 1995), all U.S. Government end users acquire cov-
ered code with only those rights set forth herein. 106 11. MISCELLANEOUS. EXHIBIT A -Mozilla Public License. This license represents the complete agreement concerning subject matter hereof. If any provision of this license is held to be unenforceable, such provision shall be reformed only to the extent necessary to make it enforceable. This License shall be governed by California law provisions
(except to the extent applicable law, if any, provides oth-
erwise), excluding its conflict-of-law provisions. With respect to disputes in which at least one party is a citizen of, or an entity chartered or registered to do business in the united states of america, any litigation relating to this License shall be subject to the jurisdiction of the federal courts of the northern district of california, with venue lying in santa clara county, california, with the losing party responsible for costs, including without limitation, court costs and reasonable attorneys' fees and expenses. The application of the united nations convention on contracts for the International sale of goods is expressly excluded. Any law or regulation which provides that the language of a contract shall be construed against the drafter shall not apply to this license. 12. RESPONSIBILITY FOR CLAIMS. As between initial developer and the contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under this license and you agree to work with initial developer and contributors to distribute such responsibility on an equitable basis. Nothing herein is intended or shall be deemed to constitute any admission of liability. 13. MULTIPLE-LICENSED CODE. Initial developer may designate portions of the covered code as "Multiple-Licensed". "Multiple-Licensed" means that the initial developer permits you to utilize portions of the covered code under your choice of the NPL or the alternative licenses, if any, specified by the initial developer in the file described in exhibit A. The contents of this file are subject to the Mozilla Public License Version 1.1 (the license); you may not use this file except in compliance with the License. You may obtain a copy of the license at http://www.mozilla.org/MPL/
Software distributed under the license is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See the license for the specific language governing rights and limitations under the License. The Original Code is ______________________________________. Initial Developer The is___________________. Portions created by ______________________ are Copyright (C) _______________________. All Rights Reserved. the Original Code of Contributor(s): ______________________________________. Alternatively, the contents of this file may be used under the terms of the _____ license (the "[___] License"), in which case the provisions of [______] license are applicable instead of those above. If you wish to allow use of your version of this file only under the terms of the [____] license and not to allow others to use your version of this file under the MPL, indicate your decision by deleting the provisions above and replace them with the notice and other provisions required by the [___] license. If you do not delete the provisions above, a recipient may use your version of this file under either the MPL or the [___] license."
NOTE: The text of this exhibit A may differ slightly from the text of the notices in the source code files of the original code. You should use the text of this exhibit A rather than the text found in the original code/source code for Your modifications. 107 COMMERCIAL MODE SETUP GUIDE Note: All features shown within this guide may not be available on all models. EXPERIENCED INSTALLER Commercial Mode Setup page 7 B-LAN Setup page 45 Cloning Information pages 21 - 25 For Customer Support/Service, please call:
1-888-865-3026 www.lgcommercial.com www.zenith.com RECORD Model and SERIAL NUMBER The model and serial number of this TV is located on the back of the cabinet. For future reference, we suggest that you record those numbers here:
Model No._________________Serial No. _______________ WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. POWER CORD POLARIZATION:
This product is equipped with a 3-wire grounding-type alternating current line plug. This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the three-wire ground type plug. NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the cable TV system installers attention to Article 820-40 of the National Electric Code
(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con-
nected to the grounding system of the building, as close to the point of the cable entry as practical. REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION:
Do not attempt to modify this product in any way without written authorization from LG Electronics U.S.A., Inc. Unauthorized modification could void the users authority to operate this product. COMPLIANCE:
The responsible party for this products compliance is: LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632, USA Phone: 1-201-816-2000. P A G E 2 Marketed and Distributed in the United States by LG Electronics U.S.A., Inc. 2000 Millbrook Drive, Lincolnshire, IL 60069 Copyright 2009, LG Electronics U.S.A., Inc. 206-4118 IMPORTANT SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS Important safeguards for you and your new product This product has been manufactured and tested with safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into the new product, please read and observe the following safety points when installing and using the new product, and save them for future reference. Observing the simple precautions discussed in this installation and operating guide can help get many years of enjoyment and safe operation that are built into the new product. This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association 1. Read Instructions All the safety and operating instructions should be read before the product is operated. 2. Follow Instructions All operating and use instructions should be followed. 3. Retain Instructions The safety and operating instructions should be retained for future reference. 4. Heed Warnings All warnings on the product and in the operating instructions should be adhered to. 5. Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. Water and Moisture Do not use this product near water for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet base-
ment, or near a swimming pool. 7. Accessories, Carts, and Stands Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tri-
pod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should fol-
low the manufacturers instructions, and should use a mounting accessory recommended by the manufacturer. 8. Transporting Product A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 9. Attachments Do not use attachments not recommended by the product man-
ufacturer as they may cause hazards. 10. Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This prod-
uct should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturers instructions have been adhered to. 11. Power Sources This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to oper-
ate from battery power, or other sources, refer to the operating instructions. 12. Power Cord Polarization (Some models) This product is equipped with a three-wire grounding type alternating-current power plug. This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety pur-
pose of the three-wire ground-type plug. 13. Power Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, conve-
nience receptacles, and the point where they exit from the product. PORTABLE CART WARNING 206-4118 P A G E 3 IMPORTANT SAFETY INSTRUCTIONS
(Continued from previous page) 14. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the prod-
uct, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code
(U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, ground-
ing of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, con-
nection to grounding electrodes, and requirements for the grounding electrode. Example of Grounding According to National Electrical Code Instructions Ground Clamp Antenna Lead in Wire Electric Service Equipment Antenna Discharge Unit
(NEC Section 810-20) Grounding Conductor
(NEC Section 810-21) Ground Clamps Power Service Grounding Electrode System (NEC Art 250, Part H) NEC - National Electrical Code 15. Lightning For added protection for this product (receiver) during a light-
ning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 16. Power Lines An outside antenna system should not be located in the vicini-
ty of overhead power lines or other electric light or power cir-
cuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17. Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 18. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 19. Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 20. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjust-
ment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e. If the product has been dropped or the cabinet has been damaged. f. If the product exhibits a distinct change in performance. 21. Replacement Parts When replacement parts are required, be sure the service tech-
nician has used replacement parts specified by the manufactur-
er or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 22. Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 23. Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as rec-
ommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. 24. Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. P A G E 4 206-4118 Table of Contents Use this page as a reference to find pages or sections to go to and set up the TV features. Go to page 7 to begin the Commercial Mode Master TV setup. Warnings . 2 Important Safety Instructions . 3 - 4 Table of Contents . 5 Setup Checklist . 6 Commercial Mode Setup for Master TV . 7 Installer Overview . 8 FTG Card Mode of Operation Overview . 9 FTG Card Operation Setup . 10 FTG Card Channel Map Overview . 11 FTG Installer Menu Overview . 12 FTG Operation Troubleshooting . 13 Typical Installers Remote Control . 14 Installer Remote Control Key Functions . 15 Rear Connections Panel . 16 A/V Input 2 Side Connections Panel/RF Antenna Connection 17 RJP / TV Connections & Setup . 18 MPI Card Slot / PPV Card Installation . 19 TV Features Configuration Menus Overview . 20 TLL-1100A Cloning Instructions / Learning Setup . 21 -22 - 23 LT2002 Cloning Instructions . 24 - 25 Installer Menus . 26 - 27 - 28 - 29 - 30 - 31 References Detailed Instructions For Making A Master TV . 32 Editing Channel Icons/Adding Ch Labels 2-5-4 + Menu Mode 33 Clonable Menu Features / Checking Software Version . 34 USB End User Features . 35 USB Cloning Setup: Master TV Learning . 36 USB Cloning Setup: Master TV Teaching . 37 TV Camport Auto Sense Operation . 38 TV Aux Input Configuration / Troubleshooting . 39 Troubleshooting . 40 LT2002 Cloning Troubleshooting . 41 Troubleshooting Flow Chart . 42 Commercial Mode Check . 43 Glossary of Terms . 44 B-LAN Setup and Overview . 45 RJP Model List and Input Hierarchy . 46 Notes . 47 Back Cover . 48 Notes See the Installers menus to set up the operational features of the TV. The Installers section content is intended to be used pri-
marily by qualified TV electronics technicians. Reference is made to installer remote controls used for menu operation within the manual. The remote information is provided for reference only. The typical installer remote control shown for reference in this manual may be different than the actual remote control supplied with the TV. For any additional information, contact your LG representative. Note: Design and specifications are subject to change without prior notice. Marketed and Distributed in the United States by LG Electronics U.S.A., Inc. 1000 Sylvan Avenue Englewood Cliffs, NJ 07632 For Customer Support/Service please call:
1-888-865-3026 www.lgcommercial.com 206-4118 P A G E 5 Setup Checklist Installation and Setup Checklist __ Unpack TV and all accessories. __ Install batteries in remote control. __ Install TV on Vesa Mount or Stand. Note: It may be advisable to make all hard-
wire connections before installing on Vesa mount or stand, as appropriate. Hardware Connections __ Install any additional hardware as appropriate to your institution, LAN etc. Hardwire Connections __ Make all connections to rear Jack Pack and RF antenna on MPI card. __ Make all connections to signal, interactive resources and Aux sources as appropriate. GAME CONTROL AV IN 1 VIDEO AUDIO L(MONO) R Y PB VIDEO PR L R AUDIO COMPONENT IN RJP RESET UPDATE RGB IN (PC)
..... .... .... AUDIO IN
(RGB / DVI) HDMI
.......... ......... 2 1 HDMI/DVI IN SPEAKER OUT
(8 ) REMOTE CONTROL OUT
..... ... RS-232C IN
(SERVICE ONLY) TV-LINK CFG Except 32LH240H Installer Menu Items Setup __ Configure all relevant Installer menu items as required of your institution. TV Menus Configuration Configure TV features for the end user. __ Channel __ Picture __ Audio __ Option __ Time __ Lock __ Choose on screen menu language.
(English is the default language.) Commercial Mode Setup __ Commercial Mode Setup, see next page. Software Installation __ Install or configure any software as applic-
able; PPV etc. Additional Features Setup See page 5, Table of Contents. __ Select viewing source on TV. P A G E 6 206-4118 Commercial Mode Setup for Master TV This page provides an overview of a Master TV configuration. Note 1: Disconnect all Aux inputs. Under certain conditions, Auto Tuning (Channel search) is disabled if there is an Aux input active. Commercial Mode Setup Procedure 1. Set Installer Menu Items
(Enter TV Installer Menu, see Installer menus for detailed instructions.) a. Set Installer menu item 117 FACT DEFAULT, to 001 and press ENTER on Installer remote. (This clears all installer menu custom settings, channel labels / icons etc. and reloads the factory default settings.) b. Set Item 003 BAND/AFC.
- Broadcast: set to 000.
- CATV: set to 001.
- HRC: set to 002
- IRC: set to 003 c. Set item 028 CH OVERIDE to 001. This allows access to channel search, Auto Tuning and Channel List/Edit options in the Channel Menu. d. Set other particular installer items that affect your TV programming net-
work. Enable/Disable Aux sources, set a Start Channel etc. e. After all required installer menu item settings have been adjusted, press ENTER on the remote to remove Installer Menu. 2. Set Up TV Features
(Channel, Picture, Audio, Lock, Time, Option, Digital Captions etc. See TV Clonable options list and TV menus pages.) 3. Run Auto Tuning (Channel Search)
(Search for all available channels.) Go to the Channel Menu and access the Auto Tuning option, follow onscreen instructions. a. Edit Channel Scan. In the Channel Menu, access Channel Edit option. Add/Delete channels per your system requirements. Note: Physical channel numbers are used to identify Virtual channels. Add familiar channel trademarks/logos like ABC, CBS, NBC etc. to the Channel-Time onscreen display. In the Channel menu, select the Channel Label option. Add identifiable labels (logos) for the end user to readily know what common networks are available. 4. Transfer TV Setup to Internal TV Controller: 2-5-5 + Menu Mode After the TV channel scan has been edited and channel label icons added, enter the Installer menu. Once in the Installer menu, press 2-5-5 and MENU on the remote. This transfers the TV setup to the internal controller box. 5. Add Custom Channel Labels for Analog Channels: 2-5-4 + Menu Mode Enter Installer menu, press 2-5-4 and MENU. Add your own custom text labels to channel onscreen displays. Note: Digital Channels often have a broadcaster generated label. (See 2-5-4+Menu pages.) When finished, to exit 2-5-4+Menu mode, press MENU. Verify TV Setup At this point, verify that the channel lineup, channel icons and custom labels are correct. Make sure the TV features are set per your requirements. Set item 028 Ch Overide to 000 to lock the channel scan. After the pre-
ceding has been completed, the Master TV setup is ready to be copied to a Clone Programmer, see cloning options pages. XXLH250H INSTALLER MENU 000 INSTALLER SEQ 000 UPN 000-000-000-000 PTC V1.00.000 FPGA E0F1 CPU V3.06.00 Typical TV Installer Menu 117 FACT DEFAULT 003 BAND/AFC 028 CH. OVERIDE 00X 00X 001 Adjust the settings for these Installer Menu Items DIGITAL 19-3 MONO STEREO SAP WXYZ Custom Text Label WXYZ created in 2-5-4 + Menu (Add Channel Label) Mode 093 RJP AVAILABLE 001 Set 093 RJP Available to 001 if using a remote jack pack 028 CH. OVERIDE 000 After Master TV setup has been completed, set item 028 Ch Overide to 000. 206-4118 P A G E 7 Installer Overview This is the commercial mode setup guide only. Operating Installer Menu To set up the controls for the TV you will need to know how to enter the TV Installer menu and make changes to the default values as required. If necessary, familiarize yourself with the TV Installer menu and how to make and save changes in the menu. LG Installer Remote You will need an LG Installer remote control similar to the one shown to the right. The installer remote must have a Source but-
ton or its equivalent. The remote shown in this manual has INPUT
-- this button serves the purpose of a Source button. The TVs clonable features need to be set up. This is a critical step. If the Master TV display panels clonable features like adding channel icons or channel labels are not done correctly, then the cloned TVs will all have problems. Refer to the Owners Manual for other TV fea-
tures: Video, Audio, Closed Captions, V-Chip, etc. TLL-1100A Clone Programmer The TLL is a very simple cloner to use. It can be set up to clone a master TV setup and transfer it into a target TV. Cloning is accom-
plished using the TV/Cloner MPI ports for communica-
tion. Be sure the Master TV is set up completely. Cloning is only possible when the TV is tuned to an Aux source or Analog channel, not a digital channel. TV Link Loader-Demo TLL1100A Ready MODE MENU ENTER RECEIVE SEND TLL1100A XXLH250H INSTALLER MENU 000 INSTALLER SEQ 000 UPN 000-000-000-000 PTC V1.00.000 FPGA E0F1 CPU V3.06.00 Typical Installer Menu MARK RATIO 1 4 7 LIST VOL POWER INPUT CC 3 6 9 FLASHBK 2 5 8 0 MUTE CH P A G E ENTER MENU RETURN TIMER ALAM SAP EJECT P A G E 8 206-4118 Outlined below is the FTG (Free-To-Guest) setup for individual TV control FTG Card Mode of Operation Overview 1. Set up commercial features of TV/STB. Enter Installer Menu and set all desired items as required. (i.e. Tuning Band, Start Channel etc.) Refer to the Installation and Setup Guide of the TV/STB. 2. Load the FTG Configuration Application program onto the PC that will be used to configure the FTG card. 3. Install FTG card into TV/STBs MPI card slot and connect PC. (See below) 4. Execute the FTG Configuration Application and create a configuration file. 5. Build a Channel Map and Write it to FTG card. (Converts card from pass-through to FTG mode.) 6. If necessary, make changes to Installer Menu items using FTG Installer Menu Configuration utility and Write them to FTG card. 7. Save the configuration file (*.rml) for future use. 8. Tune TV/STB to a Logical Channel in the Channel Map. LMT7Z7 Configured Card in FTG Mode of Operation FTG CARD INSTALLER MENU CHANNEL MAP TARGET TV/STB INSTALLER MENU CHANNEL MAP FTG CARD INSTALLER MENU CHANNEL MAP TARGET TV/STB INSTALLER MENU CHANNEL MAP Different Model TV/STB Function Card only copies Installer Menu items and then installs Channel Map. Same Model TV/STB Function Card installs both Installer Menu items and Channel Map. A N T E N N A I N M P
. I
. ANTENNA/CABLE INPUT Receives RF signals. M.P.I. INTERFACE Available MPI port. RETAINING SCREW Install after inserting the LMT7Z7 card. RETAINING SCREW Install after inserting the LMT7Z7 card. 206-4118 P A G E 9 FTG Card Mode of Operation Contd. It is easy to determine the operating mode of the TV/STB. By pressing Menu, if the Setup or TV menu appears, the Z7 card is in pass-through mode. If the End User Function menu appears, the TV/STB is in FTG mode. CHANNEL PICTURE AUDIO TIME OPTION LOCK INPUT USB Communications Setup Menu Sets up the communications link between the FTG Configuration Application and the Z7 card installed in a TV/STB. Typical TV/STB Setup Menu Shows that the Z7 card is in pass-through mode. This menu can also be accessed by turning IR remote access On in the FTG Configuration Application, while the TV/STB is in FTG mode. ASPECT RATIO Move Enter Set By Program ABC 4:3 16:9 Zoom Just Scan End User Aspect Ratio or Function Menu Shows that the Z7 card is in FTG mode. While this menu is present on-screen, the only way the Installer menu can be accessed is by the FTG Configuration Application. Network Icon Selection Menu Select channel icons like ABC, NBC etc., to add to the channel OSDs to identify common networks for the end user. P A G E 1 0 206-4118 Creating/copying a channel map into LMT7Z7 card will convert the card from pass-through mode to FTG mode. When Aspect Ratio menu is present, card is in FTG mode. FTG Channel Map Overview LOGICAL CHANNEL NUMBERS Channels appear in numerical order. Select logical, Major and Minor num-
bers on menu. CUSTOM CHANNEL LABELS/ICONS Set custom labels and select icons on menu. SET CHANNEL ATTRIBUTES Set encrypted, OSD on or off or blank video only. EXIT Exits menu and returns to logical channel listing. DELETE Removes channel from lineup. ADD After inputting a new chan-
nels data, press to add chan-
nel to list. UPDATE After editing a channels data, press to include the changes in the channel list. CHANNEL MAP EDITOR Shows both channel data and logical channel lineup. 206-4118 P A G E 1 1 FTG Installer Menu Overview CONFIGURATION SETTINGS Select tabs for Installer submneu items to set up TV/STB. HOSPITAL GRADE TV/STB ITEMS Set hospital only items on Installer menu for Hospital grade TV/STBs. INSTALLER DEFAULTS Press to reset TV/STB to Installer menu defaults. IR REMOTE ACCESS Toggle IR remote access to On to get access to TV/STB feature menus or Installer menu. WRITE Press to transfer the FTG Installer menu values to the FTG card and TV/STB. READ Press to transfer the Installer menu values on the FTG card to the PC FTG Configuration Application. EXIT Returns to logical channel map menu. LEARN Press to transfer the installer menu settings on the TV/STB to the FTG card and PC FTG Configuration Application. P A G E 1 2 206-4118 FTG Operation Troubleshooting LMT7Z7 Configured Card in FTG Mode of Operation Error Messages Problem Probable Cause Solution Cannot contact target. FTG application already open. Close extra FTG application on computer. Cable(s) not connected. TV off. Check and connect communication cables. Turn TV on. Wrong Communication port. Select correct Comm port on computer. 206-4118 P A G E 1 3 Typical Installer Remote Control MARK RATIO 1 4 7 LIST VOL POWER INPUT CC 3 6 9 FLASHBK 2 5 8 0 MUTE CH P A G E ENTER MENU RETURN TIMER ALAM SAP EJECT LG Installer Remote Control The remote control is supplied with and dedicated to operate the TV. Some DVD and VCR controls may be available for some LG DVD/VCR products. See next page for typical key functions in TV mode and DVD/VCR control. Follow the instructions provided in the Installer menu pages to access the Installer menus. A A
+ A A +
A A Installing Batteries in Installer Remote Control Remove the battery compartment cover on the back side by loose the bolt on the battery compartment cover, pressing the arrow tab and sliding the cover downward. Install batteries matching correct polarity as shown (+ with + and - with -). Install two high-quality alkaline 1.5V AAA batteries. Never mix old or used batteries with new ones. Replace cover. P A G E 1 4 206-4118 Installer Remote Control Typical Key Functions Remote Control Key Functions: This typical LG TV remote control is shown for reference. Follow the instructions provided on the Installer menu pages to access the Installer menu. MARK Use to mark or unmark a photo/music. RATIO Adjusts the picture aspect ratio. POWER Turns TV On or Off. MUTE Switches the sound On or Off. VOLUME UP/DOWN Increases/decreases the sound level. MARK RATIO 1 4 7 LIST VOL POWER INPUT CC 3 6 9 FLASHBK 2 5 8 0 INPUT Selects RGB, HDMI,DVI, HDMI2, Component Input, AV1 and AV2 sources. CC Selects a closed caption option:
Off, CC1 ~ 4, Text1 ~ 4, Service 1 ~6. NUMBER Buttons (0 - 9) DASH Use to enter a program number or channels. Dash is used for sub channel numbers such as 2-1, 2-2, 9-1, 9-2, 100-3, 100-4 etc. FLASHBACK Returns to the previously tuned channel. MUTE CH P A G E CHANNEL UP/DOWN Selects available channels found with Auto Tuning. Moves to next available page in elec-
tronic program guide. MENU Displays the main menu on the screen. Enters or exits the on-screen menu system ENTER VCR/DVD BUTTONS Control some video cassette recorders or DVD players. (RECORD is not functional in DVD mode.) Set up for VCR recording: Once, Regularly, Weekly, Off. (RECORD button only). TIMER Sets the amount of time before the TV automatically turns itself Off. ALARM Sets the time that the TV will automatically turn itself On. MENU RETURN TIMER ALAM SAP EJECT THUMBSTICK Up/Down/Left/Right/ENTER Use to navigate on-screen menus / adjust the TV settings to your requirements. RETURN Clears all on-screen displays and returns to TV viewing from any TV menu. SAP Selects MTS sound:
Mono, Stereo, and SAP in Analog mode. Changes the audio language in DTV mode, if additional languages are available. SAP Notes If SAP is selected and no SAP is provided, sound may not be heard on channel. Each analog channel may have its own SAP setting. Digital channels will reset to default audio lan-
guage with a power Off/On. EJECT Clears all on-screen displays and returns 206-4118 P A G E 1 5 Rear Connections Panel RESET Press RESET to re-initialize the TV. HDMI/DVI PORT Connect to output jacks from HDMI / DVI device. AUDIO/VIDEO IN 1 Connect to output jacks on audio/video device. LAN Connect to control network.
(Except 32LH240H) GAME CONTROL AV IN 1 VIDEO AUDIO L(MONO) R Y PB VIDEO PR L R AUDIO COMPONENT IN RJP RESET UPDATE RGB IN (PC)
..... .... .... AUDIO IN
(RGB / DVI) HDMI
.......... ......... 2 1 HDMI/DVI IN SPEAKER OUT
(8 ) REMOTE CONTROL OUT
..... ... RS-232C IN
(SERVICE ONLY) TV-LINK CFG COMPONENT IN Connect to output jacks on component device. SPEAKER OUT 8-OHM Connect to external speaker input. REMOTE CONTROL OUT Connect to remote control device. UPDATE Restricted to software updates. REMOTE JACK PACK PORT Connect to remote jack pack control output port. RGB IN (PC) Connection for RGB hookup from PC. AUDIO IN (RGB / DVI) Audio connection for either RGB or DVI device. TV-LINK Use for FTG downloads.
(Except 32LH240H) RS-232C IN Used for downloading soft-
ware updates, etc. P A G E 1 6 206-4118 A/V 2 Input: Side Connections Panel / RF Antenna Connection USB IN Insert USB device for software updates and usable for Picture/Music entertainment. L/MONO-AUDIO-R IN Connect to audio output jacks from external device. For mono audio output, connect to Left audio input. RF Antenna Connection N I B S U
. I R
O D U A
O N O M
L O E D V I AV IN 2 VIDEO IN Connect to video output port on external device. RF ANTENNA Connect to Antenna / Cable input on MPI card. Antenna or CATV A N T E N N A I N M P
. I
. 206-4118 P A G E 1 7 Remote Jack Pack (RJP) / TV Connections after Commercial Mode Setup and Cloning Master TV Setup Procedures Make these connections after commercial mode setup and cloning procedures are complete Remote Jack Pack Setup RJP Available? If you will use a remote jack pack in your system, set installer item 093 RJP Available to 001 so the RJP function is enabled. Note: Make RJP connections first then set 093 to 001. 093 RJP AVAILABLE 001 HDMI/DVI PORTS Connect to output jack(s) from HDMI / DVI RJP. AUDIO/VIDEO IN 1 Connect to composite Video/Audio output jacks on RJP. GAME CONTROL AV IN 1 VIDEO AUDIO L(MONO) R Y PB VIDEO PR L R AUDIO COMPONENT IN RJP RESET UPDATE RGB IN (PC)
..... .... .... AUDIO IN
(RGB / DVI) HDMI
.......... ......... 2 1 HDMI/DVI IN SPEAKER OUT
(8 ) REMOTE CONTROL OUT
..... ... RS-232C IN
(SERVICE ONLY) TV-LINK CFG REMOTE JACK PACK PORT Connect to control output port on RJP. RGB IN (PC) Connection for RGB hookup from RJP. AUDIO IN (RGB / DVI) RGB/DVI Audio input from RJP. LAN Connect to control network.
(Except 32LH240H) P A G E 1 8 206-4118 MPI Card Slot / PPV Card Installation The MPI card is equipped with an RF jack for antenna/cable signal source connection. The MPI card slot is also available for installing a PPV (Pay-Per-View) card. MPI Card Removal / PPV Card Installation 1. Remove the two MPI card retainer screws. 2. Pull out current MPI card far enough so that the RF cable can be detached from the old card. 2. Detach RF cable. 3. Place new PPV card into slot and slide it in far enough to reconnect RF cable. 4. Insert card all the way into the slot making sure it is fully seated into back plane connector. 5. Replace the two card retainer screws. A N T E N N A I N RF CABLE RF cable needs to be dis-
connected to remove cur-
rent card. D C I N M.P. I. Card Slot M P
. I
. 206-4118 P A G E 1 9 TV Features Configuration Menus Overview The onscreen menus control the basic TV features CHANNEL PICTURE AUDIO TIME OPTION LOCK INPUT USB Main TV Menus The Main TV setup menus control the features of the TV. Set the TV features to the desired configuration for the end user. Use the USB port to upgrade TV software. P A G E 2 0 206-4118 TLL-1100A Cloning Connections/Learning Setup Connections for the TLL-1100A Clone Programmer to Learn the TV Master TV Setup On Master TV Set up all Master TV features on the menus and do a Channel Search. Add Channel and Aux labels etc. See previous page. Insert MPI cable into TV MPI port. CLONE SELECTION MENU Selected Bank: CBank X Saved
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP M.P.I. Learning Setup Antenna
(or CATV) On TLL-1100A 1. Turn On the TLL-1100A. 2. Use the Mode button to select Clone Mode. 3. Use the Left/Right arrow to select the CBank (1 - 8) to store the master setup in. 4. Plug the other end of the MPI cable into the MPI port on the bottom of the TLL. 5. With the Installer remote con-
trol, select item 1 on TLL menu. 6. Press Enter, to transfer the Master setup into CBankX on the TLL. The TLL will copy the master setup. 7. When learning is done, discon-
nect MPI cable from Master TV. 8. Reconnect TV power cord. Power the TV On and the master setup should be resident on the TV. On Target TV 1. Connect MPI cable from the TLL to the MPI port on the Target TV. Assure that the correct CBank(X) is selected on TLL.. 2. With the Installer remote con-
trol select item 2, to Teach the target TV the master TV setup. 3. Press Enter to begin teaching. 4. When Teaching is done, discon-
nect MPI cable and power the TV Off. Unplug TV power cord. 5. Reconnect TV power cord. Power the TV On and the mas-
ter setup should be resident on the TV. CLONE CLOCK = 00:00 TV CLOCK = 00:00 THE CLONE IS VERSION V2.2.2
-To change menu items, Press channel keys or digits.
-To execute item, Press ENTER. TV Link Loader-Demo TLL1100A Ready MODE MENU ENTER RECEIVE SEND TLL1100A TV Link Loader-Demo TLL1100A Ready MODE MENU ENTER RECEIVE SEND TLL1100A CLONE SELECTION MENU Selected Bank: CBank X Saved
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP CLONE CLOCK = 00:00 TV CLOCK = 00:00 THE CLONE IS VERSION V2.2.2
-To change menu items, Press channel keys or digits.
-To execute item, Press ENTER. M.P.I. Teaching Setup Antenna
(or CATV) Warning: Do not use the TLL-1100A while any PPV card is installed in TV or clone programmer device will be damaged. Notes: It is assumed that the TV is connected to a signal source, the TV source selected is Antenna (RF) In, the signal is from an Analog channel, not a digital channel, all equipment is connected to power and turned on and the TLL Cloner main menu is displayed on the TV screen, see above. GG If an analog channel is not available, tune TV to an Aux source lik AV-1 for cloning purposes. 206-4118 P A G E 2 1 LT2002 Cloning Connections/Learning Setup Connections for the LT2002 Clone Programmer to Learn the TV Master TV Setup Antenna or CATV Ferrite Core
(TDK, ZCAT 2035-0930) Connect cable to TV MPI Jack and follow on screen instructions Status Indicator MPI Reset green red Color battery ok battery low Blink pattern slow power on no communications heartbeat power on communications ok Warning: Do not use LT2002 while any PPV card is installed in TV or clone programmer device will be damaged. THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION THE TV IS VERSION THE SW IS REVISION XX XX XX CLONE CLOCK = XX:XX TV CLOCK = XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE. Master TV QuickSet II Programmer LT2002 ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS USA Clone Programmer Notes: It is assumed that the TV is connected to a signal source, the source selected is Antenna (RF) In, the signal is from an Analog channel, not a digital channel, all equipment is connected to power and turned on and the LT2002 Clone Programmer main menu (THE CLONE HAS CONTROL OF THE TV) menu is displayed on the TV screen, see above and next page. GG If an analog channel is not available, tune TV to an Aux source lik AV-1 for cloning purposes. Before you begin cloning... The Master TV should be connected to a good, stable signal from an over-the-air antenna or cable service Analog channel and connected to power. (See above.) Teaching and Learning is only possible between identical model devices. (However, the LT2002 Clone programmer can store up to 3 different master setups.) WARNING: Copying a blank or incorrect memory into a TV, STB or other device will cause the TV, STB or other device to operate erratically or become inoperable. Use an Installers remote to operate Learning and Teaching menus. Make sure that the batteries in the Clone programmer are If batteries are removed, the Clone Clock time will be lost. Decide if you want to set the time from the Clone program-
mer or copy the time to the Clone programmer; from a com-
patible TV which has the clock set to the current time. Setting the time and transferring it to the Clone or other device is a separate procedure. Follow the connection diagram above to connect the Clone to a Master TV TV display panel. After learning is complete, to another identical TV TV display panel to teach it the master setup. See the Clone Troubleshooting section to resolve problems. Turn to the next page to continue Cloning Setup. fresh. P A G E 2 2 206-4118 LT2002 Cloning Learning Setup Learning the Master TV Setup Instructions for the Clone Programmer to Learn the Master TV Setup Use MPI Cable to Connect LT2002 Clone Programmer to Master TV MPI Port If there is a good connection, THE CLONE HAS CONTROL OF TV message will appear. Press any key on the Installer remote. Learn Setup from Master TV Press 1 to select the LEARN FROM TV option, then press ON/OFF, POWER, or ENTER to go to the Memory Bank Selection Menu. Pick the Memory Bank you want to store the master TVs setup in by press-
ing either Channel key repeatedly to choose Memory 1, 2 or 3. (If you choose a Memory Bank that has a master devices setup pro-
grammed into it, that setup will be overwritten by the new master TVs setup.) Once the Clone memory bank is selected, press ON/OFF, POWER, or ENTER. The Clone memory bank you have selected will be shown. Press ON/OFF or POWER to begin copying the master TVs setup. Set the Clock (Optional) Set the time on a Master TVs Clock. (If the time has already been copied from a TV into the Clone programmer, you can set a master TVs clock by copying the time from the Clone programmer.) The Clone Programmer can copy the current time to both a master TV and to the Clones internal clock; accurate to within one minute. (Another reason that the Clone programmer should be equipped with fresh, high-quality alkaline batteries, is for it to keep the time as accurate-
ly as possible.) Since the Clone Programmers time cannot be set directly, the current time needs to be copied from a Zenith/LG TV equipped with M.P.I. input capability. After the time is copied to the Clone programmer, the current time can then be transferred to another TV. (This can be a master TV, or another TV which has already had the features set up.) THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION THE TV IS VERSION THE SW IS REVISION XX XX XX CLONE CLOCK=
TV CLOCK=
XX:XX XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE. This menu should appear by itself after the LT2002 is connected to the TV MPI port. CLONE SELECTION MENU
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.
-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER This menu should appear after any key is pressed on the Installer remote. LT2002 Clone Programmer Communication Problems A slow flashing green light indicates there are communica-
tion problems between the TV and the LT2002 clone program-
mer. If this is the case, check for a damaged cable, poor con-
tacts, or other connection troubles. If the status indicator is red, the programmer batteries are low and should be replaced. Install 4 high-quality alkaline AA batteries. 206-4118 P A G E 2 3 Cloning Connections/Teaching Setup Teaching the Master Setup to Another TV Connections for the LT2002 to Teach another TV the Master Setup Antenna or CATV Ferrite Core
(TDK, ZCAT 2035-0930) Connect cable to TV MPI Jack and follow on screen instructions Status Indicator MPI Reset green red Color battery ok battery low Blink pattern slow power on no communications heartbeat power on communications ok THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION THE TV IS VERSION THE SW IS REVISION XX XX XX CLONE CLOCK = XX:XX TV CLOCK = XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE. Target TV GG If an analog channel is not available, tune TV to an Aux source lik AV-1 for cloning purposes. Teach Master TVs Setup to the target TV After learning is complete, remove the M.P.I. cable from the master TV and connect it to the target TV that you want to copy the master TVs setup into. With THE CLONE HAS CONTROL OF TV message displayed, press 2 or use either Channel key to go to the TEACH TO TV option, press ON/OFF, POWER, or ENTER. Select the LT2002 memory that the new setup is in. Press On/Off to transfer the new setup and other information to the new TV. Teaching usually takes 2-3 minutes. After the TEACHING COMPLETE message is displayed, press any key to return to the Clone menu, then press ON/OFF, POWER, or ENTER. If finished, detach M.P.I. cable from the target, newly-cloned TV. Disconnect TV Power for 15 Seconds Unplug the AC power cord of the newly-cloned TV from the power outlet for about 15 seconds to activate the newly-
copied setup. P A G E 2 4 QuickSet II Programmer LT2002 ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS USA Clone Programmer CLONE SELECTION MENU
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.
-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER This menu should appear after any key is pressed on the Installer remote. TEACHING IN PROGRESS, PLEASE WAIT This display will appear during Teaching function. TEACHING COMPLETE This display will appear after Teaching is complete. 206-4118 Reference: LT2002 Cloning Procedure Troubleshooting Warning: Do not use LT2002 while any PPV card is installed in TV or clone programmer will be damaged. Reset Clone After Static Shock After replacing exhausted batteries, or if the programmer behaves strangely after a static shock, use a paper clip or simi-
lar instrument inserted through the small hole marked RESET to activate the internal reset switch and restore normal opera-
tion. After a reset, check the real-time clock setting. It may be necessary to reset the Clone Programmer clock from a TV con-
taining the correct time. Note The LT2002 programmer is designed to be used with TVs con-
taining the 221-01006 and later processors. Use with earlier TV sets may give unpredictable results. Processors used before the 221-01006-04 have a limited screen display capability. They cannot display entire screens as shown in the quick setup instructions accompanying the LT2002 clone programmer. Use the printed menu illustrations on the quick setup sheet sup-
plied with the Clone as an aid to making your programming choices. (Although the menus are not all displayed, the clone functions all operate normally.) Clone Programmer Troubleshooting Problem Possible Cause(s) Possible Solution(s) Clone Programmer Clone copies Setup in less than 30 seconds Remote does not operate clone. LED does not blink. Not enough time to copy entire TV setup.
- Press Reset on clone programmer, redo teach/learn.
(Teach/Learn should take a minimum of 1 minute.) Wrong Installer remote.
- Only use an LG Installer remote to operate clone programmer with TV. M.P.I. cord not connected. TV not turned on. Weak batteries.
- Connect M.P.I. cord properly, assure good connection.
- TV must be powered On for clone to work.
- Install 4 fresh AA high-quality alkaline batteries. Clone menu hard to read. Weak signal.
- Connect TV to a reliable Analog channel signal source. No time set. Time not available.
- Set time on a TV, copy time to Clone Programmer. Clone not working. Clone programmer problem.
- Try a different LT2002 Clone programmer.
- Reset Clone Programmer. Clone Scans Channels more than once. Clone should only scan channels once.
- Retry cloning again. Master and Other TVs Cloning did not work. Procedure interrupted. Different TV models. Step(s) omitted or not performed.
- Wait until procedure complete message is displayed.
- Cloning is only possible with identical model TVs.
- Reread pages 7-8-9 to be sure all tasks were performed. Clone time disappeared. Batteries were removed.
- Batteries must remain installed to retain time settings. New Setup not present. TV not reset.
- Disconnect newly-cloned unit from power for 5 seconds. After cloning operations are complete, just unplug the LT2002 from the TV. If the TV does not display a picture on the TV (blank screen) after a few seconds, just change channels. 206-4118 P A G E 2 5 Installer Menu Use the Installers Menu to set up or change operational settings. See more detailed descriptions of the Installer menu items on the following pages... Accessing the Installers Menu Make sure TV is on. Installers menu items can be accessed by using an installers remote control. Just press MENU repeatedly until the TV seems to stop responding, then press 9, 8, 7, 6, then ENTER to access the Installers menu. To remove the Installers menu, press ENTER again. Any changes you make will be stored in nonvolatile memory. The Installers menu opens with item 000 INSTALLER SEQ 000. Use the Up/Down arrow keys to sequence through the available menu items. Or, access an item directly by keying in the line number, then pressing MENU. For example, to access the Sleep Timer option which is item 015, press 0-1-5, then MENU. To change a setting, use the Left/Right arrow keys. Or, enter a value directly. Using the Installers Menu Items 000 ~ 118 are immediately accessible only upon entering the Installers Menu. Their numbers, descriptions, ranges, factory default settings, and a place for listing any changes made on-site are given below and on the following pages. Installer menu items not relevant to this TV series are not present on the Installer menu, therefore some num-
bers are missing. Items 006, 012, 013 etc., will not appear. Installer Menu Items 000 through 034 XXLH250H INSTALLER MENU 000 INSTALLER SEQ 000 UPN 000-000-000-000 PTC V1.00.000 FPGA E0F1 CPU V3.06.00 Typical Installer Menu Menu Item Function Value Range Default Value Brief Description of Function and Comments 000 001 002 003 004 005 007 008 009 010 011 015 016 017 021 022 023 028 029 030 031 032 034 INSTALLER SEQ POWER MANAGE AC ON BAND/AFC STRT CHANNEL CHAN LOCK STRT VOLUME MIN VOLUME MAX VOLUME MUTE DISABLE KEY DEFEAT SLEEP TIMER EN TIMER ALARM V-CHIP MAX BLK HRS CAPTION LOCK CH. OVERIDE OLD OCV ACK MASK POLL RATE TIMING PULSE CAMPORT EN 0 ~ 3 0 ~ 7 0 / 1 0 ~ 3 0 ~ 127, 255 0 / 1 0 ~ 63, 255 0 ~ 63 0 ~ 63 0 / 1 0 / 1 0 / 1 0 / 1 0 / 1 0 / 1 0 ~ 99 0 / 1 0 / 1 0 / 1 0 / 1 20 ~ 169 186 ~ 227 0 / 1 0 0 0 1 255 0 255 0 63 0 0 1 0 1 1 12 0 1 0 0 94 207 1 Leave default set to 0. Sets number of hours of no activity before auto shut Off. Set to 1 to enable auto turn On at power up. Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC Channel at turn-on (Set to 255 to tune in last channel before power Off). If set to 1, cannot tune from current channel. Sets Volume level at TV turn-on (Set 255 to retain last volume level). Sets minimum allowable volume setting. Sets maximum allowable volume setting. Set to 1 to disable mute function. Set to 1 to disable menu navigation keys on display panel. Set to 1 to enable Sleep Timer. Set to 1 to enable On/Off Timers. Set to 1 to enable Alarm. Set to 1 to enable V-Chip functions. Sets number of V-Chip (Parental Control) blocking hours. Set to 1 to retain caption setting at power Off. If set to 0, limits direct access to favorite channels. Set to 1 to change M.P.I. operation to OCV. If set to 1, changes M.P.I. for some OCV boxes. Selects poll rate for M.P.I. Sets baud rate for M.P.I. Set to 1 to enable Video 2 input. P A G E 2 6 206-4118 Installer Menu Installer Menu Items 035 through 118 Menu Item Function Value Range Default Value Brief Description of Function and Comments 035 038 039 040 046 047 053 069 070 071 073 075 078 079 080 081 082 083 084 087 088 090 091 093 094 096 098 099 102 103 104 106 116 117 118 COMPPORT EN. YPrPb EN. REAR AUX EN AUTO CAMPORT STRT AUX SRCE AUX STATUS DIS. CH-TIME EN. CH-T COL. FOR. CH-TIME BCK. CH-TIME CH NOT AVBLE REVERT CH UPN MSB UPN MSB-1 UPN MSB-2 UPN LSB CHKSM ERROR HANDSHK TIME PERMANENT BLK REAR RGB EN. EN NOISE MUTE KEY LOCK YPrPB2 EN 0 / 1 0 / 1 0 / 1 0 / 1 1 ~ 6, 255 0 / 1 0 / 1 0 / 1 0 ~ 7 0 ~ 7 0 / 1 0 / 1 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 / 1 0 ~ 5 0 / 1 0 / 2 / 18 0 / 1 0 / 1 0 / 1 RJP AVAILABLE 0 1 2 5 6 SAP MENU EN DEF. ASP. RATIO START GEM CH BACK LIGHTING ATSC BAND ATSC TUNE MODE START MINOR CH ASP RATIO LOCK VIDEO MUTE EN FACT DEFAULT POWER SAVING 0 / 1 0 ~ 4 0 ~ 135, 255 1 ~ 100 101 ~ 200, 255 255 200 0 ~ 4 0 / 1 0 ~ 255 0 / 1 0 / 1 0 / 1 1, 3, 7 4 1 0 0 0 0 3 1 1 1 1 6 0 0 1 2 2 0 0 0 0 0 0 1 5 0 2 1 0 1 0 1 2 Set to 0 to disable HDMI 1. Set to 1 enable HDMI 1 Set to 1 to enable display panel Component Video 1 input jacks. Set to 1 to enable display panel Video 1 input jack. Set to 1 to automatically switch to Camport. If set to 1, STRT AUX SRCE cannot be set to 2. Set to 1 for M.P.I. AUX source to be reported as a channel number instead of Channel 0. Sets the starting AUX source. Set to 1 to disable Channel-Time display. Set to 1 to enable custom color for the Channel-Time display. Chooses custom foreground color for the Channel-Time display. Chooses custom background color for the Channel-Time display. If set to 1 and channel override is 0, NOT AVAILABLE message is displayed when directly accessing a channel not in the favorite channel list. If set to 1 and loss of M.P.I. communication occurs, TV tunes to Start Channel. User programmable number, most significant byte. User programmable number, most significant byte - 1. User programmable number, most significant byte - 2. User programmable number, least significant byte. Enforces rigid M.P.I. checksum. Relaxes M.P.I. timing to be compatible with PC based Windows-controlled systems. Removes block hours setting for Parental Control and makes block permanent. Set to 0 to disable RGB1. Set to 2 to enable for PC and Auto Configure always enabled. Set to 18 to enable for PC and Auto Configure one time only after AC ON. If set to 1, mutes audio if no signal is present. If set to 1, keyboard is locked out, IR is still functional. Set to 1 to enable HDMI-2 input. Set to 0 to disable. Set to 1, 2, 5 or 6 for HDMI or DVI mode. (See detailed descriptions.) Set to 0 to disable feature on Function menu. Set to 1 to enable feature on Function menu. Sets default aspect ratio at power up. See detailed descriptions and item 106. Sets the stating Gem channel, 255=last channel at power Off. Settings above 101 control dynamic back lighting and disable power saving mode.. Sets the brilliance of the TV picture backlighting. Selects ATSC band. Default 01 for physical channel scan. Set to 0 for Virtual Channel scan. Selects Minor start channel. Set 0 for NTSC. Not 0, sets Minor channel number. To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on power cycle. Set to 0 for normal, set to 1 for Blank. 0=Normal. 1=Loads presets of all above settings. Set to 1 to be powered at b-Lan module. Set to 3 to bo powered at b-Lan module only when TV is powered on. Set to 7 to be not powered at b-Lan module. Note 1: Dependent on item 093 RJP Available setting.
(Except 32LH240H) 206-4118 P A G E 2 7 Installer Menu Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE Specifies entry sequence to the Installer Menu. 1 = 4321 3 = 3698 0 = 9876 2 = 1478 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The POWER MANAGE function is for saving energy. If set to 0, Power Manage is Off. Settings range from 0 ~ 7, with 1 ~ 7 representing the hours that the unit will remain On, unless there has been activity from either the control panel or remote control. 002 - AC ON (AC Power Switchable) If set to 1, allows the TV to turn On just by applying AC power. Pressing the On button is not necessary. This is desirable if the TV is plugged into a cable box or a power outlet controlled by a wall switch. Use ADJ Left/Right arrow to choose 0 or 1 where 0 is the default is Off, and 1 is On. NOTE: If set to 1 (On), the TV does not respond to On/Off commands from either the remote or the display control panel, and the SLEEP TIMER is also nonfunctional. 003 - BAND/AFC (Band/Automatic Frequency Control) There are 4 possible settings for this option:
0 = Broadcast 2 = HRC 1 = CATV 3 = IRC If some channels were not found by Auto Tuning (Channel Search), select the appropriate Band setting here and add the channels using the Channel Edit option in the Channel Menu. 004 - STRT CHANNEL (Start Channel) If active, this function allows you to determine the initial channel number when the TV is turned On. This feature is useful for an in-
house information channel, since the TV would always select that channel when it is turned On. Setting this to 255 causes the last channel viewed when the TV was turned Off, to be the tuned to chan-
nel when the TV is turned On again. Note: For a digital Start Channel, always remember to set item 104 to the Minor Start Channel number. 255 = Last channel 126 Map to Channel 3. 1 ~ 125 = Ch X 0 = Aux 127 Map to Channel 4. 005 - CHAN LOCK (Channel Lock) CHAN LOCK is ideal if the system must always be on the same channel. Changing channels with Channel Up/Down or keypad numbers is impos-
sible. Channel Lock is inactive if set to 0 (default). Generally, this feature is used in connection with START CHANNEL
(Installer item 004) where the start channel may, for example, be set to 3 or 4. If the start channel is 3, then the TV will remain locked on Channel 3. NOTE: For Items 007, 008 and 009 For legacy reasons, the scale used is 0 - 63. The PTC software will translate this to the 0 - 100 scale used by the TV. To translate a TV volume level to the installer menu value, use the fol-
lowing formula:
Installer Value = TV Value x 63 100 Enter only the whole number (disregard fractions). 007 - STRT VOLUME (Start Volume) This function allows the Installer to determine the initial volume level setting when the TV is turned On. This feature is useful for an in-house information channel, since the TV would always select that volume level when it is turned On. The range of values are 0 - 63, 255. If 255 is selected, the current volume level will be retained in memory when the TV is turned Off; at turn On, the volume level will be automatically set at the previous or last level. 008 - MIN VOLUME (Minimum Volume) This function determines the minimum volume level allowable with the VOLUME (VOL) Up/Down control. In this way, for example, someone cannot set the volume too low to hear. The value range is from 0 to 63 change values with ADJ Left/Right arrow. The factory default is 0, which provides the full range of volume control, if item 009 MAX VOL-
UME is also set to 63. It may be best to set the same value on every TV. NOTE: The minimum volume level cannot have a value setting higher than the MAX VOLUME level (described below). 009 - MAX VOLUME (Maximum Volume) This function determines the maximum volume level allowable with the VOLUME (VOL) Up/Down controls. In this way, for example, someone can not set the volume level high enough to disturb others. The value range is 0 to 63, with 63 as the default, which gives the user the full range of volume control, if item 008 MIN VOLUME is also set at 0. Change values with ADJ Left/Right arrow keys. It may be best to set the same value on every TV. NOTE: The maximum volume level cannot have a value setting lower than the MIN VOLUME level (described previously). 010 - MUTE DISABLE Enables or disables sound mute function. If set to 1, sound cannot be muted. If set to 0, sound can be muted. P A G E 2 8 206-4118 011 - KEY DEFEAT (Keyboard Defeat) If set to 1, key defeat prevents the end user from accessing the on-
screen menus with the display front panelMENU, SELECT, and Left /
Right arrow keys do not function. If set to 0, those keys do function. NOTE: The menus can always be accessed by pressing MENU on the remote. 015 - SLEEP TIMER If set to 1, the SLEEP TIMER feature may be used. If set to 0, the Sleep Timer is not available. 016 - EN TIMER (Enable On/Off Timers) *
If set to 1, Timer function is available to user and enabled continuous-
ly. Set to 0 to disable On/Off Timers. (Clock must be set in order to use Timers.) 017 - ALARM *
Gives the installer the option of making the Alarm function available to the end user. If set to 1, Alarm function is available to end user. Set to 0 to disable the Alarm function. NOTE: Clock must be set before the Alarm function will work. 021 - V-CHIP (Parental Control) *
Set to 1 to activate V-Chip (Parental Control); have it available to end user to filter and control or otherwise restrict programming content that can appear. Set to 0 to turn V-Chip feature Off, not available to user; no programming restrictions can be set. 022 - MAX BLK HRS (Maximum Block Hours) *
Sets hours from 0 to 99 for the maximum V-Chip (Parental Control) block hours. Default setting is for 12 blocking hours. 023 - CAPTION LOCK Set to 1 to restore previous caption On/Off state after turn Off. If set to 0, captions are always Off at turn On. 028 - CH. OVERIDE (Channel Override) If set to 1, the user can select channels with either Channel up/down or by direct keypad entry. If set to 0, only those channels that are entered for scanning can be selected. 029 - OLD OCV (On Command VideoTM) Set to 1 for operation with systems from On Command Corporation. 030 - ACK MASK M.P.I. Communication Parameter. Leave at default setting unless changed by Pay-Per-View provider. When set to 1, changes M.P.I. for some OCV boxes.
* Only affects Function Menu if enabled by some PPV providers. Installer Menu 031 - POLL RATE M.P.I. Communication Parameter. Selects Poll Rate for M.P.I. Leave at default setting unless changed by Pay-Per-View provider. Step size of 16 ms. 032 - TIMING PULSE M.P.I. Communication Parameter. Leave at default setting unless changed by Pay-Per-View provider. Sets baud rate. Step size of 4.3 uS. 034 - CAMPORT EN. (Camera Port Enable) Set to 1 to enable Video 2 input on display panel. If set to 0, Video 2 input on display panel is not functional. NOTE: S-Video overrides Video jack. 035 - COMPPORT EN. (Computer Port Enable) Enable/disables display panel HDMI1 input jack. Set to 0 to disable HDMI 1. set to 1 to enable HDMI 1. NOTE: The setting above is ignored if Installer item 093 RJP AVAIL-
ABLE, is set to 1. 038 - YPrPb EN. (Rear Component Video Enable) Set to 1 to enable display panel rear Component Video input jacks. Set to 0 to disable display panel rear Component Video input jacks. 039 - REAR AUX EN. (Rear Aux Enable) Set to 1 to enable display panel rear AUX (Video 1) input. Set to 0 to disable display panel rear AUX (Video 1) input. Note: S-Video overrides Video. 040 - AUTO CAMPORT Set to 1 to automatically switch to Camport when equipment is con-
nected to front Video input. Set to 0 to disable front Video automatic source selection. NOTE: If set to 1, 093 RJP Available is automatically set to 0. 046 - STRT AUX SRCE (Start Aux Source) Sets the starting AUX source. At power up, TV will tune to starting Aux source if item 004 Start Channel is set to 0. If item 093 RJP Available is set to 0 and item 040 Auto Camport is set to 0:
1 = Video 1 2 = Video 2 3 = HDMI 1 4 = RGB 5 = HDMI 2 6 = Component 255 = Last Aux If item 093 RJP Available is set at 1:
2 = Video 2 5 = HDMI 2 6 = Component If item 040 Auto Camport is set to 1:
1 = Video 1 3 = HDMI 1 4 = RGB 5 = HDMI 2 6 = Component 206-4118 P A G E 2 9 Installer Menu Detailed Descriptions of Installer Menu Items 047 - AUX STATUS Set to 1 for M.P.I. AUX source to be reported as a channel number instead of channel 0. Set to 0 to disable AUX identification change. Controls M.P.I. status channel response for AUX inputs. 053 - DIS. CH-TIME (Disable Channel-Time) Set to 1 to disable the Channel-Time display, Channel-Time display will not appear. Set to 0 to enable the Channel-Time display. 069 - EN. CH-T COL. (Enable Channel-Time Custom Color) Set to 1 to enable custom color for the Channel-Time display. Set to 0 to disable custom color for the Channel-Time display. 070 - FOR. CH-TIME (Channel-Time Display Foreground Color) Set according to Color Chart. 0 = Black 3 = Yellow 4 = Blue 1 = Red 2 = Green 5 = Violet NOTE: If foreground and background color are the same, menu back-
ground is transparent. 6 = Cyan 7 = White 071 - BCK. CH-TIME (Channel-Time Display Background Color) Set according to Color Chart. 3 = Yellow 0 = Black 1 = Red 4 = Blue 2 = Green 5 = Violet NOTE: If foreground and background color are the same, menu back-
ground is transparent. 6 = Cyan 7 = White 073 - CH NOT AVBLE (Channel Not Available) If set to 1 and item 028 CHANNEL OVERRIDE is set to 0, NOT AVAIL-
ABLE message is displayed when directly accessing a channel not in the channel scan list available in memory. 075 - REVERT CH (Revert to Start Channel) If set to 1 and loss of M.P.I. communication occurs, TV automatically tunes to the specified Start Channel. 078 - UPN MSB (UPN Most Significant Byte) User programmable number, most significant byte readable by M.P.I. command. Note: Not linked to serial number. 079 - UPN MSB-1 (UPN Most Significant Byte-1) User programmable number, most significant byte-1 readable by M.P.I. command. Not linked to serial number. 080 - UPN MSB-2 (UPN Most Significant Byte-2) User programmable number, most significant byte-2 readable by M.P.I. command. Not linked to serial number. 081 - UPN LSB (UPN Least Significant Byte) User programmable number, least significant byte readable by M.P.I. command. Not linked to serial number. 082 - CHKSM ERROR (Checksum Error) Enforces rigid M.P.I. checksum validation. Set to 1 for validation. Set to 0 to disable (does not check checksum on M.P.I. async port). SPI is always checked. 083 - HANDSHK TIME (Handshake Time) Adds an additional delay to the handshake time which is 64 msec, thus relaxing M.P.I. timing requirements to be compatible with PC based Windows controlled systems, range is 0 - 5.
(Timeout = 25.5MS + [25.5 MS* Handshake time]). 084 - PERMANENT BLK (Permanent Block) Allows Lock (Parental Control) blocking schemes to be permanent by disabling the blocking hours function. Set to 1 to install Parental Control restrictions permanently. Set to 0 for user-specified hours control of blocking schemes. 087 - REAR RGB EN. (Rear RGB Enable) Controls access to rear RGB input on TV. Set to 0 to disable RGB input. Set to 2 to enable for PC and Auto Configure always enabled. Set to 18 for Auto Configure one time only with power cord removal and reinsertion. 088 - EN NOISE MUTE (Enable Noise Mute) If set to 1, audio mutes if no signal is present. 090 - KEY LOCK If set to 1, display panel keyboard is locked out, not available to end user. IR receiver remains functional. 091 - YPrPb2 EN. (HDMI2 Enable) Set to 0 to disable display panel HDMI2 input. Set to 1 to enable DTV mode. Set to 2 to enable PC mode. P A G E 3 0 206-4118 Installer Menu 093 -RJP AVAILABLE (Remote Jack Pack Available) 0 = Remote jack pack is not available or disabled. 1 = Legacy Model RJPs: HDMI Mode Enables RJP when an HDMI cable is inserted into RJP. Video is from HDMI. Audio stream is expected from HDMI source. If no audio is pre-
sent, no audio will be heard. 2 = Legacy Model RJPs: DVI Mode Enables RJP when an HDMI cable is inserted into RJP. Video is from HDMI however, Audio is from selected audio source, based on the RJPs audio hierarchical priority. 5 = Scaler Model RJPs: HDMI Mode Enables RJP when an HDMI cable is inserted into RJP. Video is from HDMI. Audio stream is expected from HDMI source. If no audio is pre-
sent, no audio will be heard. 6 = Scaler Model RJPs: DVI Mode Enables RJP when an HDMI cable is inserted into RJP. Video is from HDMI however, Audio is from selected audio source, based on the RJP s audio hierarchical priority. Notes:
See Reference section, RJP Input Hierarchy and RJP Models page. If set to 1, 2, 5 or 6, item 040 Auto Camport is automatically set to 0. Settings 1, 2, 5 and 6 allow the lodge staff to customize each TV s RJP setup based on customer requirements. 094 - SAP MENU EN (2nd Audio Program) Set to 1 to enable SAP feature on Function menu, if Function menu is available. Set to 0 to disable SAP feature on Function menu, if Function menu is available. 096 - DEF. ASP. RATIO (Default Aspect Ratio) Selects default aspect ratio at power up, see settings below. Set to 0 for Set By System. Set to 1 for 4:3. Set to 2 for 16:9 (Factory Default). Set to 3 for Just Scan Set to 4 for Zoom 099 - BACK LIGHTING Sets the TV screen brightness at power up, see settings below. Default setting is 200. 1 - 100 Static Backlighting.
(1 = Dimmest picture, 100 = Brightest picture.) 101 - 200 Dynamic Backlighting.
(101 = Dimmest picture, 200 = Brightest picture.) If settings are above 101, the TV automatically controls backlighting depending upon the picture level of the current program. set to 255, to disable power saving mode. 102 - ATSC BAND Sets up TV to receive different types of incoming signals:
0=Broadcast, 1=CATV, 2=HRC, 3=IRC, 4=Same as NTSC. 103 - ATSC TUNE MODE Sets ATSC tuning mode: Default set to 1 for Physical channel scan. Set to 0 for Virtual Channel scan. 104 - START MINOR CHANNEL Sets XX-XX minor start channel number at power up: 0=NTSC. If not 0, number selected is the Minor start channel number. 106 - ASP RATIO LOCK (Aspect Ratio Lock) Set to 1 to retain previous aspect ratio with power Off. Set to 0 to retain default aspect ratio with power Off. See item 96 Default Aspect Ratio above. 116 - VIDEO MUTE EN (Video Mute Enable) Set to 0 for normal. Set to 1 for blank. 117 - FACT DEFAULT (Factory Default) Set to 0 for normal. Set to 1 to load presets to all of the previous item set-
tings. WARNING: Setting this to 1 will reload the factory defaults and clear the channel list including erasing any assigned Channel Icons and custom channel Labels. 118 - Power Saving (Except 32LH240H) Default is set to 3. When TV is in Standby mode, MPI card slot is powered by Standby power supply and embedded BLAN is not pow-
ered. When TV is in Power On mode, MPI card slot is powered by main 12V power supply and embedded BLAN is powered. Note, TV must be powered on in order to communicate with the embedded BLAN module for configuration and control. 1 = MPI card slot Standby mode power provided from Standby power supply and embedded BLAN is always powered on. 3 = MPI card slot Standby mode power provided from Standby power supply and embedded BLAN only powered on when TV is powered on. 7 = MPI card slot Standby mode power provided from Standby power supply and embedded BLAN always powered off. 206-4118 P A G E 3 1 Reference: Detailed Instructions For Making A Master TV IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING... To set up a master TV you will need to know how to enter the TV Installer menu and make changes to the default values as required. If necessary, famil-
iarize yourself with the TV Installer menu and how to make and save changes in the menu, before attempting to clone the TV Master TV setup. You will also need an LG Installer remote control similar to the one shown in the front of this manual. The installer remote must have a Source button or its equivalent. The remote shown in this manual has a INPUT button -- this button serves the purpose of a Source button. Finally, the TVs clonable features need to be set up. This is a critical step. If the Master TV display panels clonable features like adding channel icons or channel labels, digital font options etc., are not correctly added, then the cloned TVs will all have problems. As the cloning procedure is being performed, specific steps need to be done at the indicated times to achieve the desired result. Be sure to do each task as indicated. If a procedure or step is left out or not performed completely, cloning may not work. At each step, pay attention to assure the TV screen shows the proper message when cloning. If the message indicated does not appear, there is a problem with that step and cloning may not be successful. Cloning is only possible when the signal source is an Analog channel, not a digital channel. Making a Master TV Detailed Instructions The following describes the procedure for preparing a Master TV for cloning and the procedure for adding Channel Icons and/or Labels. Note 1: Disconnect all Aux inputs. Under certain conditions, Auto Tuning Channel Search is disabled if there is an Aux input active. Note 2: Under certain conditions, changes to the input mode of the RGB inputs will not take effect until the power is cycled (TV is turned Off and On). To avoid confusion, disconnect all RGB inputs before entering the Installer menu. 1. Enter the TV installer menu. a. Reset the internal controller to factory default by access-
ing installer menu item 117 FACT DEFAULT, set it to 1 and press ENTER. The value will change back to 0 after the TVs internal controller has been restored to factory default con-
dition. This step will ensure that the TV channel memory will be the active channel list. Check the Status LED. If it is blinking rapidly then the TV channel map is in use. b. Within the Installer menu, set the Installer menu items to the configuration required of your institution. c. It is important to set the tuning band at this time, see Installer menu item 03 BAND/AFC. d. Set Installer menu item 28 CH OVERIDE to 001 to allow access to the Auto Tuning and Ch. Edit features in the Channel Menu. Exit the Installer menu. 2. Access the Master TV menus and set the clonable options on the menus to the desired configuration. Refer to the Clonable Menu Features Chart in this manual. 3. Run Auto Tuning to find analog and digital channels. 4. Enter the Channel Edit menu and edit the channel lineup to include the Free-To-Guest Channels only. 5. Assign ICONs to the channels using the Channel Label Menu. Note: You can add Channel ICONS typically network logos like ABC, NBC, PBS etc. in this step. Or, in Step 7, add Channel ICONS or labels for channels without Icons. 6. Transfer the TV setup: Enter the TV installer menu. Press 2, 5, 5, MENU to start the transfer of the TVs setup to the internal controller. Once the transfer is complete, the sys-
tem will exit the Installer menu. Check the Status LED inside the TV. It should be blinking slowly (1 blink per second). 7. Edit/Add Channel ICONs and Channel Labels as needed. Enter Installer menu. With menu displayed, press 2-5-4 +
MENU. See next page for detailed instructions:
- Editing/Adding Channel ICON and Labels on Master TV
- Changing a Channels ICON on Master TV
- Changing/Adding Channel Labels on Master TV
- Changing Source Labels on Master TV 8. Verify Master TV setup and feature configuration:
Did you add Channel ICONS?
Did you add Channel Labels?
Did you add Source Labels?
Did you adjust all TV menu options as required?
After verifying master setup, enter the TV Installer menu and set Installer menu item 28 CH OVERIDE to 000. Press ENTER to remove and exit the Installer menu. P A G E 3 2 206-4118 Reference: Procedures for adding Channel Label Icons/Custom Channel Labels
(2-5-4 + MENU Mode) Adding Channel Icons and Labels in the 2-5-4 + Menu Mode Editing/Adding Channel ICONs and/or Labels If there is no pre-assigned ICON, you can make a custom chan-
nel label of up to 7 characters to help in identifying the chan-
nel or network. At your option, channel labels can also be added in addition to a pre-assigned ICON. You may also add labels for the Aux input sources to clearly identify the devices that are connected to the Aux inputs.
(Icon) XYZ XYZ XYZ NETWORK
(Label) 1 2 3 4 5 6 7 Editing and adding the labels can only be done if there are channels entered into the TVs channel map either by using the method described in item 6 (page 18), by cloning or by the use of the master remote control from the PPV provider. Note: A blank letter space is available between Z and !. To Do Channel Editing/Labeling, Proceed as Follows 1. Enter TV Installer menu. 2. Once the installer menu appears, press 2, 5, 4, MENU. This enters the channel label editing mode. Add your channel icons and channel labels in this menu, see below. (You can do this more than once.) 3. To exit the menu when done press MENU. Changing a Channels ICON on Master TV 1. With Channel Up/Down, select the channel you want to change the Icon for. 2. With the Right or Left ADJ arrow, select the thin letter I on the channel ID display. 3. With the Up or Down arrow, select the desired ICON you want to appear to identify the channel. (If you know the ICON number, enter the number followed by Enter /
Select.) 4. Proceed with Changing/Adding Labels or go to the next channel. Changing/Adding Channel Labels on Master TV 1. Channel Up/Down to select the desired Changing Source Labels on Master TV 1. Press INPUT to select the desired channel. 2. Press the Right or Left ADJ arrow repeatedly until the numbers 1 to 7 show up. The number shows the posi-
tion of the character that can be changed. Number 1 is the first charac-
ter, number 2 the second character and so on. Aux input source; A/V 1, A/V 2, HDMI Component, RGB etc. 2. Press the Right or Left arrow repeated-
ly until the numbers 0 to 9 shows up. The number shows the position of the character that can be changed. 3. Use the Up or Down arrows to select the desired character. 3. With the Up or Down arrow, select the 4. Press INPUT for the next Aux source desired character. 4. Proceed to the next number position or use Channel Up/Down to go to the next channel. or proceed with Changing Icon or Changing/Adding Labels. Press Ch Up/Down to return to channels. Installer Remote Control Key Functions for Master TV Channel Editing/Labeling Menu CHANNEL Up/Down - Tunes in the next channel in scan. Left/Right Arrows - Select the item to change. If I is 0 9 - Use to enter the index number of the ICON, if known. ENTER/SELECT - Changes the ICON after the number has shown, the ICON can be changed. If a number is shown, it indicates the position of the character that can be changed. Up/Down Arrows - Select the ICON or the character to be displayed. Tip: Arrows can be held down for fast scrolling. been entered. INPUT - Changes the Aux input label. (Source on the remote shown in this manual is INPUT.) MENU - Exits the editing process. 206-4118 P A G E 3 3 Reference: Clonable Menu Features Menu /Sub Menu Features Installer Menu Installer Item settings Channel Auto Tuning (Channel Lineup) Channel Edit Channel label Picture Aspect Ratio Picture Mode Advanced Control Audio Auto Volume Clear Voice Sound Mode Balance Clonable Menu Features Audio Contd. Treble Bass SRS TruSoundXT TV Speaker Option Language Caption Caption Mode DTV Captions Style - Style DTV Captions Style - Size DTV Captions Style - Font DTV Captions Style - Text Color DTV Captions Style - Text Opacity DTV Captions Style - BG Color DTV Captions Style - BG Opacity DTV Captions Style - Edge Type DTV Captions Style - Edge Color Lock Movie Rating TV Rating Children Age TV Rating Children Fantasy Violence TV Rating General Age Input Block Time Auto Clock Manual Clock Off Time On Time Auto Off Notes Picture Menu and other menu settings shown above are not clonable on all TVs. End user has access to Picture, Sound and Ratio on user remote control. Menu options vary between Analog / Digital channels and Aux Sources. Procedure for Checking Software Version The software version of the TV may be checked by accessing the Installer Menu. To do this, press MENU repeatedly until the menu display ceases to respond to MENU key presses. Then, press "9", "8", "7", "6", "ENTER". Press ENTER again to remove Installer Menu from screen. XXLH250H INSTALLER MENU 000 INSTALLER SEQ 000 UPN 000-000-000-000 PTC V1.00.000 FPGA E0F1 CPU V3.06.00 Typical Installer Menu PTC Version CPU Version P A G E 3 4 206-4118 USB End User Features USB Menu features Picture Slideshow with or without Music accompaniment USB Device Setup On the USB device, load Photo and Music files e.g. MP3. Insert USB device into USB port on TV side jack panel. Press Menu and select USB option, press Enter. Note: Windows .wma files are not usable. USB View Pictures Select USB Icon and press Enter. Select Photo List option and press Enter. Select Folder photos are in. Press Enter. When photo list appears, choose Photo and press Enter. View Picture with Music Select USB Icon and press Enter. Select Music Folder option. Select Music List and select Play with Photo. Select music MP3 file and press Enter. Listen to Music MP3 Files Select USB Icon and press Enter. Select Music List option and press Enter. Select Folder with Music MP3 files. Press Enter. Adjust Volume to comfortable listening level. Slide Being Shown Indicates present slide being shown and number of slides available. Sound Level Indicates volume setting. Slideshow 1 / 79 9 Slideshow BGM Delete Option Hide Slideshow Toggles slideshow On and Off. Back Ground Music Toggles selected music file On and Off. Rotate Rotates picture. Delete Removes slide from slideshow. Hide Removes menu from screen. Press Enter to display again. Option Press to access available options. Selects slideshow playback speed. 206-4118 P A G E 3 5 Reference USB Cloning: Master TV Profile Setup-Learning USB Download Menu Upgrade TV Software Upgrade PTC Software Teach To TV Learn From TV Learn From TV UPGRADING... Do not unplug!
48 %
On Master TV, Create Profile and Learn 1. Set up all Master TV features on the menus and do a Channel Search.Add Channel and Aux Labels etc. Do 255+menu on Installer Menu to save current TV into flash memory. 2. Plug USB memory card into the USB In port on Master TV. 3. Press Menu key to open Main menu. Highlight the Option icon. 4. Press the Left arrow key once, the Option icon on left side of menu will be highlighted. 5. Press number key 7 a total of 7 times. 6. Access the Learn From TV option. a. First, Expert Download Menu page will not show the Learn From TV . In order to make Learn From TV available, key in the password which is used to enter Installer Menu. Example 9-8-7-6. b. By pressing up/down arrow keys (if there is other menus), place the cursor on Learn From TV, then press Enter Key. 7. Using Up/Down arrow key,highlight Learn From TV , then press Enter. 8. To identify the profile from others, you can change the last 5 digits. Key in a custom file name, then press the Enter key. 9. The Learning status will be shown on progress bar. As soon as learning the current profile is com-
plete, a message will appear on screen indicating the learning process is done. 10. Remove the USB memory card. Optional: Edit / Change File Name If necessary, the file name can be edited or changed. Learn From TV Select the file name and press OK to start. E XX250H-UA00001.TLL E Previous Enter Notes Do not remove TV power cord or USB memory card while Learning, doing so might harm your USB memory card. Do not remove TV power cord or USB memory card while Teaching,doing so may cause the T V t malfunction. You are allowed to edit the file name, however, a file with edited contents will not be recognized. Since clock data is copied into USB memory card as numeric data,the time difference between teaching and learning is not automatically adjusted. Either set the clock manually, or use Auto Clock set on TV main menu. P A G E 3 6 206-4118 Reference USB Cloning: Master TV Profile Setup-Teaching Teach To TV XX250H-UA00001.TLL Previous Enter Teach To TV UPGRADING... Do not unplug!
39 %
On Target TV, Teach Master TV Profile 1. Plug USB memory card with Master TV Profile setup into Target TV USB input port. 2. Press Menu key to open Main menu and then highlight the Option Menu icon. 3. Press the Left arrow key once, this will highlight the Option icon on left side of menu. 4. Press number key 7 , a total of 7 times. 5. Using the Up/Down arrow key, select Teach to TV, then press Enter key. 6. Use Up/Down arrow keys to navigate through profiles. Select the profile that you want to install by highlighting it and pressing the Enter key. 7. Teaching progress will be shown on the progress bar. As soon as teaching is done, a message will appear indicating that the teaching process has been completed. 8. When Teaching is done, remove the USB memory card and unplug TV power cord. 9. Reconnect TV power cord. Power the TV On and the master setup should be resident on the TV. 206-4118 P A G E 3 7 TV Camport Auto Sense Operation The CAMPORT Auto Sense function is enabled when:
1. Installer Menu Item 34, CAMPORT EN is set to 1 AND 2. Installer Menu Item 40, AUTO CAMPORT is enabled (1). CAMPORT (Front Video) Functionality Control Item 34 CAMPORT EN Item 40 AUTO CAMPORT Selectable= Can be accessed with INPUT key, direct access, etc. Auto Sense= Switches to this input when connector is inserted. The camport (Side Video) has the highest priority and will over-
ride any commands including tuning to the Start Channel. 0 0 1 1 0 1 0 1 Front Video Operation Disabled Disabled Selectable Auto Sense State Upon Removal Of CAMPORT Previous Aux or RF Channel Last Requested RF or Aux Channel Previous Aux or RF Channel State Upon Removal Of CAMPORT Previous Aux or RF Channel Previous State Before Inserting CAMPORT Aux or RF Channel Operation While CAMPORT Is Active None Aux or RF Channel Direct Access Aux or RF Channel Ch Up/Down, Flashback and TV/AV Keys Previous State Before Inserting While CAMPORT Operation CAMPORT Is Active Aux or RF Channel None Aux or RF Channel Direct Access Last Requested RF Aux or RF Channel Ch Up/Down, Flashback and TV/AV Keys or Aux Channel Last Requested Channel if PPV translates it to direct access tuning command. Otherwise, goes to Previous Aux or RF Channel 206-4118 CAMPORT Operation (Stand-Alone) When Camport Auto Sense is enabled as above, the TVs source will switch to the side video aux source whenever a plug is inserted into any of the side video panel inputs (either com-
posite Video or S-Video). When the plug is removed, the TV will switch back to the previ-
ous channel or input source that the TV was using before the plug was inserted. However, if any direct access to an RF chan-
nel or Aux channel is requested while the camport is active, then, when the camport plug is removed, the TV will switch to the last requested channel. Source changes using any Source Keys (INPUT) are ignored. Channel Up/Channel Down and Flashback Commands are not direct access tuning commands and they are also ignored. CAMPORT Operation (PPV) The operation will be similar to that of the Stand-Alone mode. However, the PPV providers may send different commands to the TV for the same user commands. For instance, some providers will always send a direct tune command when it receives a channel up/down or a flashback command while other PPV providers will just send a key command. P A G E 3 8 TV Aux Input Configuration / Troubleshooting ENABLE MPI DATA DIRECT ACCESS Tuning TV Installer Menu MPI DATA STATUS TYPE 0x41 SOURCES ENABLED (R/W) DATA STATUS TYPE 0xD2 CURRENT AV SOURCE (R) Source Input Source Mode Number Labeling Value Labeling Value Labeling DATA STATUS TYPE 0X0D AUX SOURCE
(R) START AUX SOURCE ASSIGNMENT OLD_OCV OLD_OCV=
=0 130 131 132 1 90 91 92 Video2 (Side) CV/SVIDEO Video1 (Rear) CV/SVIDEO HDMI2 133 93 HDMI1/DVI 34 39 91 91 35 35 CAMPORT_EN 0x01 REAR_AUX_EN 0x02 YPrPb2 EN = 1 0x04 YPrPb2 EN = 2 0x04 COMPPORT EN = 1 0x08 COMPPORT EN = 2 0x08 DTV PC DTV PC RGB PC 87 REAR RGB EN = 2 0x10 Component 38 YPrPb EN 0x40 134 136 137 94 96 97 Video Front
(Camport) Rear Video
(Aux) S-Video Rear S-Video Rear Front Computer Front Computer SVGA Rear Computer Y/UV Component 0 1 2 2 3 3 4 6 Video Front
(Camport) Rear Video
(Aux) S-Video Rear S-Video Rear Front Computer Front 0 (VIDE0) 0 (VIDE0) 0 (VIDE0) 2
(COMPUTER) 0 (VIDE0) 2 Computer
(COMPUTER) 2
(COMPUTER) 0 (VIDE0) SVGA Rear Computer Rear Y/PrPb Componen video Front S-Video t 2 1 5 5 3 3 4 6 USB 121 USB Options 0x80 Y/C Front 6 Video 2 (Comp) NA Troubleshooting Some quick and easy tips to resolving problems Symptoms Possible Cause(s) Possible Solution(s) Software Problems Cannot direct enter channel number or No Signal appears. Channel not included in channel scan in TV controller. After 2-5-5 + MENU, only channels included in TV controller will appear. If channel is available it can be added to channel scan. If it is not available, the No Signal message appears on the TV screen. 206-4118 P A G E 3 9 Troubleshooting Some quick and easy tips to resolving problems Symptoms Power No Power. Display Panel Picture No Picture. Erratic Operation Installer menu setup. Remote Control Remote doesnt work. Possible Cause(s) Possible Solution(s) See troubleshooting flow chart. Display panel is turned off. Antenna/Cable not connected. Connections incorrect. M.P.I. not connected. Encrypted program. Wrong tuning band.
-Turn TV on.
-Power failure?
-Connect Antenna/Cable signal to TV.
-Check connections on TV.
-If applicable, connect M.P.I. cable to M.P.I. device.
-Try another channel.
-Adjust Installer menu settings.
(See Owners manual)
(See Owners manual) Wrong Installer menu settings.
-Adjust Installer menu settings as required.
-Use Mode key to select TV; puts remote into TV mode.
-Point remote at TVs IR receiver on TV.
-Move remote closer to TVs IR receiver or darken room. Remote not in TV mode. Not aimed at IR remote sensor. Remote too far from IR sensor. IR path to TVs receiver obstructed. -Remove obstructions. Weak batteries. Wrong battery polarity. Too much light in room. Wrong Installer remote control.
-Replace batteries.
-Check that + and - match in battery compartment.
-Dim room light.
-Requires compatible Installer remote, contact your LG dealer. Picture Reception Normal picture, poor or no sound. Audio muted. Broadcast problem.
-Press MUTE or use Volume Up key to increase sound level.
-Try a different channel. Note: For other problems not caused by the TV, refer to other devices operating guide. P A G E 4 0 206-4118 Reference: LT2002 Cloning Procedure Troubleshooting Warning: Do not use LT2002 while any PPV card is installed in TV or clone programmer will be damaged. Reset Clone After Static Shock After replacing exhausted batteries, or if the programmer behaves strangely after a static shock, use a paper clip or simi-
lar instrument inserted through the small hole marked RESET to activate the internal reset switch and restore normal opera-
tion. After a reset, check the real-time clock setting. It may be necessary to reset the Clone Programmer clock from a TV con-
taining the correct time. Note The LT2002 programmer is designed to be used with TVs con-
taining the 221-01006 and later processors. Use with earlier TV sets may give unpredictable results. Processors used before the 221-01006-04 have a limited screen display capability. They cannot display entire screens as shown in the quick setup instructions accompanying the LT2002 clone programmer. Use the printed menu illustrations on the quick setup sheet sup-
plied with the Clone as an aid to making your programming choices. (Although the menus are not all displayed, the clone functions all operate normally.) Clone Programmer Troubleshooting Problem Possible Cause(s) Possible Solution(s) Clone Programmer Clone copies Setup in less than 30 seconds Remote does not operate clone. LED does not blink. Not enough time to copy entire TV setup.
- Press Reset on clone programmer, redo teach/learn.
(Teach/Learn should take a minimum of 1 minute.) Wrong Installer remote.
- Only use an LG Installer remote to operate clone programmer with TV. M.P.I. cord not connected. TV not turned on. Weak batteries.
- Connect M.P.I. cord properly, assure good connection.
- TV must be powered On for clone to work.
- Install 4 fresh AA high-quality alkaline batteries. Clone menu hard to read. Weak signal.
- Connect TV to a reliable Analog channel signal source. No time set. Time not available.
- Set time on a TV, copy time to Clone Programmer. Clone not working. Clone programmer problem.
- Try a different LT2002 Clone programmer.
- Reset Clone Programmer. Clone Scans Channels more than once. Clone should only scan channels once.
- Retry cloning again. Master and Other TVs Cloning did not work. Procedure interrupted. Different TV models. Step(s) omitted or not performed.
- Wait until procedure complete message is displayed.
- Cloning is only possible with identical model TVs.
- Reread pages 7-8-9 to be sure all tasks were performed. Clone time disappeared. Batteries were removed.
- Batteries must remain installed to retain time settings. New Setup not present. TV not reset.
- Disconnect newly-cloned unit from power for 5 seconds. After cloning operations are complete, just unplug the LT2002 from the TV. If the TV does not display a picture on the TV (blank screen) after a few seconds, just change channels. 206-4118 P A G E 4 1 Troubleshooting Flow Chart Controller Quick Check Is
'STATUS'
LED on Analog Board Blinking
Yes No Is TV
Connected to AC Power Yes Bad TV Red LED on TV Is Lit
No 1. Bad Analog Board. 2. Bad Digital Board. Yes Cycle the power by removing and re-connecting the AC power cord. Observe the
'POWER' LED and TV screen as soon as AC power is re-applied. Did Analog Board 'POWER'
LED Turn On Momentarily
No Bad TV Yes No Did TV Turn On Momentarily
Yes Check to see if TV is in Commercial Mode. See Commercial Mode Check chart. No Plug into AC Power Outlet Press 'POWER' or 'ON/OFF'
key on TV TV Turn Did On
No 1. Bad TV Yes Press 'POWER' or 'ON/OFF'
or 'VOLUME UP/DOWN' or
'MUTE' key on Installer Remote No 1. Bad TV 2. Go to Remote Control Checklist page 5 Did TV Respond
Yes Press 'POWER' or 'ON/OFF'
or 'VOLUME UP/DOWN'
or 'MUTE' key on User-Supplied Remote No Did TV Respond
Yes End 1. Bad PPV Card 2. Go to Remote Control Checklist page 5 P A G E 4 2 206-4118 Commercial Mode Check Press the "On/Off" key on the front panel. The On/Off key is always operational. No Bad TV Did you get a response
Yes Leave the TV set On Go to Installer menu by pressing "MENU" until the TV stops responding. Did TV stop responding or continue to respond
Stopped responding TV is in Commercial Mode. Continued to respond TV is not in Commercial Mode Call Technical Support for Assistance 206-4118 P A G E 4 3 Glossary of Terms A list of definitions for some of the words found in this guide 75 OHM RF CABLE DVI PHYSICAL CHANNEL NUMBER A/V DEVICE Any device that produces video or sound
(VCR, DVD, cable box, or television). High-definition television. Refers to televi-
sion signals that have higher resolution than ordinary analog TV signals. The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire sticking through the middle. It screws onto the Antenna/Cable threaded jack on the back of the TV. 300 TO 75 OHM ADAPTER A small device that connects a two-
wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on the other end. A/V CABLES Audio/Video cables. Three cables bunched togetherright audio (red), left audio
(white), and video (yellow). A/V cables are used for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices. AMPLIFIER An electronic device that amplifies sound from a television, CD player, VCR, DVD, or other Audio/Video device. ANTENNA The physical receiver of television signals sent over the air. A large metal piece of equipment does not always have to be visible to be using an antenna. B-LAN TV is controlled by external network. CABLE Cable service box. Refers to the descrambler box cable subscribers use to receive cable programming signals. CATV Programming provided by a cable service. DIGITAL TELEVISION High-resolution, cinema-quality television signals transmitted digitally. Digital Video Interface Accommodates analog and digital interfaces with a single connector. The actual channel number. Analog channels use the physical channel number and digital channels can use a virtual channel number. COMPOSITE VIDEO RGB (Red, Green, Blue) Typical video jack, uses one wire for trans-
porting three-color video signals. COMPONENT VIDEO Uses three wires for transporting three-color video signals. The end result is usually better video quality. DELETED Lets you remove channels from the list that the end user can scroll through using CH
(Channel) Up/Down. HDMI High-definition multi-media interface. HDTV HDSTB High-definition set top box. Refers to a tuner device that receives high-definition television signals which have higher resolu-
tion than ordinary analog TV signals. INPUT Refers to the input jack that receives a sig-
nal from a TV, VCR, DVD Player or other Audio/Video device. JACK An input or output connector on the back of a TV, VCR, DVD Player or other Audio/Video device. MONO SOUND Connection input or output port available for producing a video image using three sepa-
rate colors: Red, Green, and Blue. RS-232 Serial communication port through which firmware is downloaded. 2ND AUDIO PROGRAMMING/SAP Second Audio Programming (SAP) is another, separate audio channel available with some programming. Choosing SAP often refers to listening to audio in another language, such as Spanish or French. SIGNAL Picture and sound traveling through a cable, or over the air, to the TV. STEREO SOUND Stereo (Stereophonic) sound refers to audio thats divided into right and left sides. TUNER Device that picks up the broadcast signal and turns it into picture and sound. VIRTUAL CHANNEL NUMBER A re-mapped channel number analog chan-
nels use the actual channel number. but dig-
ital channels use a virtual(or false) channel number. XDS Extended Data Service: Additional program information included on the signal provided at the discretion of the broadcaster. Mono (monaural) sound is one channel of sound. On more than one speaker, all the speakers play the same audio. Note 1 OUTPUT Refers to the output jack that sends a signal out of a VCR, DVD, or other A/V device. Refer to www.atsc.org for further informa-
tion. P A G E 4 4 206-4118 B-LAN Overview B-LAN Setup and Overview (Except 32LH240H) Power to the B-LAN module is controlled by Installer Menu Item 118 Power savings. By default, value 003, the B-LAN module is only powered on when the TV is powered on. There are two bits in the Power Savings item to control power to the B-LAN module, one for power during TV Standby mode and one for power during TV Power On mode. When the bit is 0, the B-LAN module is pow-
ered. When the bit is 1, the B-LAN module is not powered (Power Savings is Enabled). Power Saving TV Standby State TV Power On State BLAN Power MPI Slot Power BLAN Power MPI Slot Power 1 3 7 On Off Off Standby Standby Standby On On Off Main Main Main The B-LAN module is internal to the TV. It allows the Hotel/Institution headend equipment to communicate with the TV for config-
uration and control. This communication is via the institutionr RF distribution system. The control device at the headend (ex FMA-
LG101) can control multiple TVs. When the TV is first installed, it must be powered on in order for the headend to be able to com-
municate with the B-LAN. At this point, if it is desired for the BLAN to always be powered on, particularly during Standby mode, the BLAN Standby Power Saving mode setting should be downloaded as Disabled. The new settings will not be active until the BLAN actually downloads the configuration data to the PTC and the PTC is reset. If it known that the application requires only using the MPI card slot and not the embedded BLAN, the installer can go into the Installer Settings menu and enable the BLAN Power Savings mode, in both Standby and TV power on. 206-4118 P A G E 4 5 Reference: RJP Model List and Input Hierarchy RJP Model List Legacy Models RJP-101M RJP-101ML RJP-110F RJP-110FW RJP-110W RJP-110WBR RJP-110S RJP-120G RJP-120T RJP-201B RJP-202B Scaler Models Not Support PCB Not Support PCB RJP-210F RJP-210FW RJP-210W RJP-210WBR RJP-210S RJP-220G RJP-220T RJP-301B RJP-302B RJP Input Hierarchy Priority 1st. (Highest) 2nd. 3rd. 4th. (Lowest) Video HDMI / DVI RGB Composite TV (RF or Aux) Audio 3.5mm Mini Jack L / R Audio In HDMI / DVI TV (RF or Aux) P A G E 4 6 206-4118 Regulatory Information cont. FCC Compliance Statement This equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment on and off), the user is encouraged to try to correct the interference by using one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's (or your) authority to operate the equipment. Only peripherals (digital input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this monitor. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used with this System. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. Canadian DOC Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. CE Conformity Notice (for Europe) Products with the CE Marking comply with the EMC Directive(89/336/EEC) and LOW VOLTAGE Directive
(73/23/EEC) issued by the Commission of the European Community. Compiance with these directives implies conformity to the following European Norms :
EN 55022 EN 55024 EN 61000-3-2 EN 61000-3-3 EN 60950-1
; Radio Frequency Interference
; Electromagnetic Immunity
; Power Line Harmonics
; Voltage Fluctuations
; Product Safety NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. Low Radiation Compliance (MPR II) This monitor meets one of the strictest guidelines available today for low radiation emissions, offering the user extra shielding and an antistatic screen coating. These guidelines, set forth by a government agency in Sweden, limit the amount of emission allowed in the Extremely Low Frequency (ELF) and Very Low Frequency (VLF) electromagnetic range. TCO'99 (TCO'99 applied model only) Congratulations!
You have just purchased a TCO99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. 01 Regulatory Information cont. Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. With the growing manufacture and usage of electronic equipment throughout the world, there is a recognized concern for the materials and substances used by electronic products with regards to their eventual recycling and disposal. By proper selection of these materials and substances, the impact on the environment can be minimized. There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Electronic equipment in offices is often left running continuously, resulting in unnecessary consumption of large amounts of energy and additional power generation. From the standpoint of carbon dioxide emissions alone, it is vital to save energy. What does labelling involve?
The product meets the requirements for the TCO99 scheme which provides for international and environmental labelling of personal computers and/or displays. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen
(The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administration). Approval requirements cover a wide range of issues:
ecology, ergonomics, emission of electrical and magnetical fields, energy consumption and electrical safety. Ecological criteria impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, and other substances. The product must be prepared for recycling and the manufacturing site(s) shall be certified according to ISO14001 or EMAS registered. Energy requirements include a demand that the system unit and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the system unit shall be reasonable for the user. Labelled products must meet strict environmental demands, for example, in respect of the reduction of electrical and magnetical fields as well as work load and visual ergonomics. Below you will find a brief summary of the ecological requirements met by this product. The complete ecological criteria document can be found at TCO Developments website http://www.tcodevelopment.com or may be ordered from:
TCO Development SE-114 94 STOCKHOLM, Sweden Fax: +46 8 782 92 07 Email : development@tco.se Information regarding TCO99 approved and labelled products may also be obtained at http://www.tcodevelopment.com Ecological requirements Flame retardants Flame retardants may be present in printed wiring board laminates, cables, and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30%
by weight of the plastic in a computer casing can consist of flame retardant substances. Many flame retardants contain bromine or chlorine, and these flame retardants are chemically related to PCBs (polychlorinated biphenyls). Both the flame retardants containing bromine or chlorine and the PCBs are suspected of giving rise to health effects, including reproductive damage in fish-
eating birds and mammals, due to the bio-accumulative*
processes when not disposed of in accordance with strict standards for disposal. TCO99 requires that plastic components weighing more than 25 grams shall not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed wiring board laminates due to the lack of commercially available alternatives. Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. TCO99 requires that batteries, the colour-generating layers of display screens, and the electrical or electronics components shall not contain any cadmium. Mercury**
Mercury is sometimes found in batteries, relays and switches. TCO99 requires that batteries shall not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. There is however one 02 Regulatory Information cont. exception. Mercury is, for the time being, permitted in the back light system of flat panel monitors as there today is no commercially available alternative. TCO aims on removing this exception when a mercury free alternative is available. Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. TCO99 permits the use of lead due to the lack of commercially available alternatives, but in future requirements TCO Development aims at restricting the use of lead. _____________________________________________
* Bio-accumulative is defined as substances which accumulate in living organisms.
**Lead, Cadmium and Mercury are heavy metals which are bio-accumulative. TCO03 (TCO03 applied model only) Congratulations!
The display you have just purchased carries the TCO03 Displays label. This means that your display is designed,manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCO03 Display requirements:
Ergonomics Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability. Energy Energy-saving mode after a certain time beneficial both for the user and the environment Electrical safety Emissions Electromagnetic fields 03 Noise emissions Ecology The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 001 Restrictions on chlorinated and brominated flame retardants and polymers heavy metals such as cadmium, mercury and lead. The requirements included in this label have been developed by TCO Development in co-operation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling system started with displays in 1992 and is now requested by users and IT-manufacturers all over the world. For more information, please visit www.tcodevelopment.com English Information for Environmental Preservation LGE. announced the 'LG Declaration for a Cleaner Environment' in 1994, and this ideal has served as a guiding managerial principle ever since. The Declaration is a foundation that has allowed us to undertake environmentally friendly activities in careful consideration of economic, environmental, and social aspects. We promote activities for environmental preservation, and we specifically develop our products to embrace the concept of environment-friendly. We minimize the hazardous materials contained in our products. For example, there is no cadmium to be found in our monitors. Information for recycling This monitor may contain parts which could be hazardous to the environment. It is important that this monitor be recycled after use. LGE. handles all waste monitors through an environmentally acceptable recycling method. There are several take-back and recycling systems currently in Regulatory Information cont. operation worldwide. Many parts will be reused and recycled, while harmful substances and heavy metals are treated by an environmentally friendly method. If you want to find out more information about our recycling program, please contact your local LG vendor or a corporate representative of LG. We set our vision and policies on a cleaner world by selecting the issue of the global environment as a task for corporate improvement. Please visit our website for more information about our green policies. http://www.lge.com/about/environment/html/Recycling.jsp Deutsch Informationen zur Erhaltung der Umwelt Im Jahr 1994 verkndete LGE die 'LG Declaration for a Cleaner Environment' (LG Erklrung fr eine sauberere Umwelt). Seitdem dient dieses Ideal als fhrendes Prinzip des Unternehmens. Diese Erklrung war die Basis fr die Durchfhrung von umweltfreundlichen Aktivitten, wobei wirtschaftliche, umweltbezogene und soziale Aspekte in die berlegungen mit einbezogen wurden. Wir frdern Aktivitten zum Schutz der Umwelt und die Entwicklung unserer Produkte ist darauf ausgerichtet, unserem Konzept bezglich Umweltfreundlichkeit gerecht zu werden. Wir sind darauf bedacht, den Anteil der in unseren Produkten enthaltenen schdlichen Materialien zu minimieren. So ist in unseren Monitoren beispielsweise kein Kadmium zu finden. Informationen zum Thema Recycling Dieser Monitor enthlt Teile, die umweltschdlich sein knnen. Es ist unbedingt erforderlich, dass der Monitor recycelt wird, nachdem er auer Dienst gestellt wurde. Bei LGE. werden alle ausrangierten Monitore in einem unter umweltbezogenen Aspekten geeigneten Verfahren recycelt. Augenblicklich sind weltweit mehrere Rcknahme- und Recyclingsysteme im Einsatz. Viele Teile werden wieder verwendet und recycelt. Schdliche Substanzen und Schwermetalle werden durch umweltvertrgliche Verfahren behandelt. Falls Sie mehr ber unser Recyclingprogramm erfahren mchten, wenden Sie sich bitte an Ihren lokalen LG-
Hndler oder einen Unternehmensvertreter von LG. 04 Wir richten unsere Firmenpolitik auf eine sauberere Umwelt hin aus, indem wir umweltspezifische Aspekte als wichtigen Punkt in die Weiterentwicklung unseres Unternehmens einflieen lassen. Zustzliche Informationen ber unsere grne Firmenpolitik erhalten Sie auf unserer Website. http://www.lge.com/about/environment/html/Recycling.jsp Franais Information sur la protection delenvironnement LGE. a publi sa 'Dclaration en faveur dun environnement plus propre' en 1994 et celle-ci est reste, depuis lors, un principe directeur de notre entreprise. Cette dclaration a servi de base notre rflexion et nous a permis de prendre en compte la fois les aspects conomiques et sociaux de nos activits, tout en respectant lenvironnement. Nous encourageons les activits en faveur de la prservation de lenvironnement et cest dans cet esprit que nous dveloppons nos produits : nous rduisons au minimum les matires dangereuses qui entrent dans leur composition et lon ne trouve pas de cadmium, par exemple, dans nos moniteurs. Information sur le recyclage Ce moniteur peut contenir des composants qui prsentent un risque pour lenvironnement. Il est donc important que celui-ci soit recycl aprs usage. LGE. traite les moniteurs en fin de cycle conformment une mthode de recyclage respectueuse de lenvironnement. Nous reprenons nos produits et les recyclons dans plusieurs sites rpartis dans le monde entier. De nombreux composants sont rutiliss et recycls, et les matires dangereuses, ainsi que les mtaux lourds, sont traits selon un procd cologique. Si vous souhaitez plus de renseignements sur notre programme de recyclage, veuillez contacter votre revendeur LG ou un lun de nos reprsentants. Nous voulons agir pour un monde plus propre et croyons au rle de notre entreprise dans lamlioration de lenvironnement. Pour plus de renseignements sur notre politique verte, rendez visite notre site :
http://www.lge.com/about/environment/html/Recycling.jsp Regulatory Information cont. Italiano Informazioni per la tutela dellambiente La LGE. ha annunciato nel 1994 la cosiddetta 'LG Declaration for a Cleaner Environment' (Dichiarazione di LG a favore di un ambiente pi pulito), un ideale che da allora funge da principio ispiratore della gestione aziendale. La dichiarazione rappresenta il fondamento che consente di intraprendere attivit a favore dell'ambiente tenendo conto degli aspetti economici, ambientali e sociali.Noi della LG, promuoviamo attivit a favore della tutela dell'ambiente sviluppando appositamente i nostri prodotti per cogliere il concetto del rispetto dellambiente riducendo i materiali dannosi presenti nei nostri prodotti. Ad esempio nei nostri monitor non presente il cadmio. Informazioni per il riciclaggio Il monitor pu presentare componenti che potrebbero risultare eventualmente dannosi per l'ambiente. importante che il monitor sia riciclato al termine del suo utilizzo. La LGE. gestisce tutti i monitor di rifiuto con un metodo di riciclaggio soddisfacente dal punto di vista ambientale. In tutto il mondo sono attualmente in funzione numerosi sistemi di riciclaggio e recupero. I diversi componenti sono riutilizzati e riciclati, mentre le sostanze dannose e i metalli pesanti vengono trattati con un metodo rispettoso dellambiente. Se si desiderano maggiori informazioni in merito al programma di riciclaggio, consigliabile rivolgersi al proprio rivenditore LG o ad un rappresentante aziendale della LG. Noi della LG impostiamo la nostra visione e le nostre politiche a favore di un mondo pi pulito ponendo la questione dell'ambiente dal punto di vista globale come una mansione rivolta al miglioramento della nostra azienda. Vi invitiamo a visitare il nostro sito internet per ulteriori informazioni sulla nostra politica verde. http://www.lge.com/about/environment/html/Recycling.jsp Espanl Informacin para la conservacin medioambiental LGE. present la 'Declaracin para un entorno ms limpio de LG' en 1994 y este ideal ha servido para guiar nuestros principios empresariales desde entonces. La Declaracin es la base que nos ha permitido llevar a cabo tareas que 05 respetan el medio ambiente siempre teniendo en cuenta aspectos sociales, econmicos y medioambientales. Promocionamos actividades orientadas a la conservacin del medio ambiente y desarrollamos nuestros productos especficamente para que se ajusten a la filosofa que protege el entorno. Reducimos al mximo el uso de materiales de riesgo en nuestros productos. Un ejemplo de ello es la ausencia total de cadmio en nuestros monitores. Informacin para el reciclaje Este monitor puede contener piezas que entraen riesgos medioambientales. Es importante reciclar este monitor despus de su utilizacin. LGE. trata todos los monitores usados siguiendo un mtodo de reciclaje que no daa al entorno. Contamos con diversos sistemas de recuperacin y reciclaje que funcionan a nivel mundial en la actualidad. Es posible reciclar y reutilizar muchas de las piezas, mientras que las sustancias dainas y los metales pesados se tratan siguiendo un mtodo que no perjudique al medio ambiente. Si desea obtener ms informacin acerca del programa de reciclaje, pngase en contacto con su proveedor local de LG o con un representante empresarial de nuestra marca. Basamos nuestra visin y nuestras polticas en un mundo ms limpio y para ellos optamos por un entorno global como tarea principal de nuestra evolucin como empresa. Visite nuestra pgina Web para obtener ms informacin sobre nuestras polticas ecolgicas. http://www.lge.com/about/environment/html/Recycling.jsp Portugus Informaes relacionadas preservao ambiental A LGE. anunciou a 'LG Declaration for a Cleaner Environment' (Declarao da LG para um ambiente mais limpo) em 1994 e esse ideal tem servido desde ento como um princpio administrativo de orientao. A Declarao a base que nos tem permitido realizar atividades favorveis ao ambiente com considerao atenta aos aspectos econmicos, ambientais e sociais. Promovemos atividades de preservao ambiental e desenvolvemos nossos produtos para englobar Regulatory Information cont. especificamente o conceito de favorvel ao ambiente. Reduzimos os materiais perigosos contidos em nossos produtos. Por exemplo, no h cdmio em nossos monitores. Informaes relacionadas reciclagem Este monitor pode conter peas que podem representar riscos ao ambiente. importante que ele seja reciclado aps o uso. A LGE. cuida de todos os monitores descartados atravs de um mtodo de reciclagem agradvel ao ambiente. H vrios sistemas de devoluo e reciclagem atualmente em operao no mundo. Muitas peas sero reutilizadas e recicladas e as substncias nocivas e os metais pesados passaro por tratamento atravs de um mtodo favorvel ao ambiente. Para obter mais informaes sobre nosso programa de reciclagem, entre em contato com seu fornecedor LG local ou com um representante corporativo da LG. Definimos nossa viso e nossas polticas relacionadas a um mundo mais limpo selecionando a questo do ambiente global como uma tarefa de aprimoramento corporativo. Visite nosso site para obter mais informaes sobre nossas polticas de meio ambiente. http://www.lge.com/about/environment/html/Recycling.jsp Nederlands Informatie met betrekking tot het behoud van het milieu LGE. publiceerde in 1994 de 'LG Declaration for a Cleaner Environment' (de LG-verklaring met betrekking tot een schoner milieu). Deze verklaring en het ideaal van een schoner milieu fungeren sindsdien als een bestuurlijke leidraad voor onze onderneming. Op basis van deze verklaring ontplooien wij milieuvriendelijke activiteiten, waarbij er zowel met sociale en economische aspecten, als met milieuaspecten zorgvuldig rekening wordt gehouden. Wij ondersteunen activiteiten die zijn gericht op het behoud van het milieu en wij houden bij het ontwikkelen onze producten specifiek rekening met de milieuvriendelijkheid van onze producten. Wij minimaliseren het gebruik van schadelijke stoffen in onze producten. Er wordt bijvoorbeeld geen cadmium verwerkt in onze monitors. Informatie met betrekking tot recycling Deze monitor bevat materialen die schadelijk zouden kunnen zijn voor het milieu. Het is belangrijk dat deze monitor aan het einde van zijn levensduur wordt gerecycled. LGE. verwerkt alle afvalmonitors via een milieuvriendelijke recyclingmethode. Hiervoor worden er momenteel wereldwijd verscheidene inname- en recyclingsystemen gehanteerd. Een groot aantal onderdelen wordt opnieuw gebruikt en gerecycled, waarbij schadelijke stoffen en zware metalen volgens een milieuvriendelijke methode worden verwerkt. Voor meer informatie over ons recyclingprogramma kunt u contact opnemen met uw plaatselijke LG-
vertegenwoordiger of een LG-vestiging. Onze visie en ons beleid met betrekking tot een schonere wereld vloeien voort uit het feit dat wij het milieu hebben aangemerkt als een onderwerp dat speciale aandacht verdient binnen onze onderneming. Bezoek onze website voor meer informatie over ons 'groene' beleid. http://www.lge.com/about/environment/html/Recycling.jsp Russian 1994 LGE
' LG ',
. 06 Regulatory Information cont. K LGE
. LG.
http://www.lge.com/about/environment/html/Recycling.jsp EPA (EPA applied model only) ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA). As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. NOM MARK (Mexico only) 07 Regulatory Information cont. WEEE (for Europe ) English Disposal of your old appliance 1.When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2.All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3.The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4.For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. French limination de votre ancien appareil 1.Ce symbole, reprsentant une poubelle sur roulettes barre d'une croix, signifie que le produit est couvert par la directive europenne 2002/96/EC. 2.Les lments lectriques et lectroniques doivent tre jets sparment, dans les vide-
ordures prvus cet effet par votre municipalit. 3.Une limination conforme aux instructions aidera rduire les consquences ngatives et risques ventuels pour l'environnement et la sant humaine. 4.Pour plus d'information concernant l'limination de votre ancien appareil, veuillez contacter votre mairie, le service des ordures mnagres ou encore la magasin o vous avez achet ce produit. Italian Smaltimento delle apparecchiature obsolete 1.Quando su un prodotto riportato il simbolo di 08 un bidone della spazzatura barrato da una croce significa che il prodotto coperto dalla direttiva europea 2002/96/EC. 2.Tutti i prodotti elettrici ed elettronici dovrebbero essere smaltiti separatamente rispetto alla raccolta differenziata municipale, mediante impianti di raccolta specifici designati dal governo o dalle autorit locali. 3.Il corretto smaltimento delle apparecchiature obsolete contribuisce a prevenire possibili conseguenze negative sulla salute umana e sull'ambiente. 4.Per informazioni pi dettagliate sullo smaltimento delle apparecchiature obsolete, contattare il comune, il servizio di smaltimento rifiuti o il negozio in cui stato acquistato il prodotto. Swedish Kassering av din gamla apparat 1.Nr den hr symbolen med en verkryssad soptunna p hjul sitter p en produkt innebr det att den regleras av European Directive 2002/96/EC. 2.Alla elektriska och elektroniska produkter br kasseras via andra vgar n de som finns fr hushllsavfall, helst via fr ndamlet avsedda uppsamlingsanlggningar som myndigheterna utser. 3.Om du kasserar din gamla apparat p rtt stt s bidrar du till att frhindra negativa konsekvenser fr miljn och mnniskors hlsa. 4.Mer detaljerad information om kassering av din gamla apparat kan fr av kommunen, renhllningsverket eller den butik dr du kpte produkten. Dutch Uw oude toestel wegdoen 1.Als het symbool met de doorgekruiste verrijdbare afvalbak op een product staat, betekent dit dat het product valt onder de Europese Richtlijn 2002/96/EC. 2.Elektrische en elektronische producten mogen niet worden meegegeven met het huishoudelijk afval, maar moeten worden ingeleverd bij speciale inzamelingspunten die door de lokale of landelijke overheid zijn aangewezen. 3.De correcte verwijdering van uw oude toestel helpt negatieve gevolgen voor het milieu en de menselijke gezondheid voorkomen. Regulatory Information cont. 4.Wilt u meer informatie over de verwijdering van uw oude toestel? Neem dan contact op met uw gemeente, de afvalophaaldienst of de winkel waar u het product hebt gekocht. Finnish Vanhojen laitteiden hvittminen 1.Tm merkki tuotteessa tarkoittaa, ett tuote kuuluu shk- ja elektroniikkalaiteromusta annetun EU-direktiivin 2002/96/EY soveltamisalaan. eller de lokale myndigheder. 3.Korrekt bortskaffelse af dit gamle apparat er med til at forhindre mulige skadevirkninger p miljet og menneskelig sundhed. 4.Mere detaljerede oplysninger om bortskaffelse af dit gamle apparat kan fs ved at kontakte dit lokale kommunekontor, renovationsselskab eller den butik, hvor du kbte produktet. Greek 2.Kaikki elektroniset laitteet ovat ongelmajtett, 1. joten ne on toimitettava paikalliseen keryspisteeseen. 3.Vanhan laitteen asianmukainen hvittminen ehkisee mahdollisia ympristn ja terveyteen kohdistuvia haittavaikutuksia. 4.Listietoa vanhan laitteen hvittmisest saat ottamalla yhteyden paikallisiin viranomaisiin, kierrtyskeskukseen tai myymln, josta ostit laitteen. German Entsorgung von Altgerten 1.Wenn dieses Symbol eines durchgestrichenen Abfalleimers auf einem Produkt angebracht ist, unterliegt dieses Produkt der europischen Richtlinie 2002/96/EC. 2.Alle Elektro- und Elektronik-Altgerte mssen getrennt vom Hausmll ber dafr staatlich vorgesehenen Stellen entsorgt werden. 3.Mit der ordnungsgemen Entsorgung des alten Gerts vermeiden Sie Umweltschden und eine Gefhrdung der persnlichen Gesundheit. 4.Weitere Informationen zur Entsorgung des alten Gerts erhalten Sie bei der Stadtverwaltung, beim Entsorgungsamt oder in dem Geschft, wo Sie das Produkt erworben haben. Danish Sdan smider du dit gamle apparat ud 1.Nr der er et tegn med et kryds over en skraldespand, betyder det, at produktet er omfattet af EU-direktiv 2002/96/EC. 2.Alle elektriske og elektroniske produkter skal smides ud et andet sted end gennem den kommunale affaldsordning ved hjlp af specielle indsamlingsfaciliteter, der er organiseret af staten
, E O 2002/96/EOK. 2.H
. 3.H
. 4.
. Spanish Cmo deshacerse de aparatos elctricos y electrnicos viejos 1.Si en un producto aparece el smbolo de un contenedor de basura tachado, significa que ste se acoge a la Directiva 2002/96/CE. 2.Todos los aparatos elctricos o electrnicos se deben desechar de forma distinta del servicio municipal de recogida de basura, a travs de puntos de recogida designados por el gobierno o las autoridades locales. 3.La correcta recogida y tratamiento de los dispositivos inservibles contribuye a evitar riesgos potenciales para el medio ambiente y la salud pblica. 4.Para obtener ms informacin sobre cmo deshacerse de sus aparatos elctricos y electrnicos viejos, pngase en contacto con su ayuntamiento, el servicio de recogida de basuras o el establecimiento donde adquiri el producto. 09 Regulatory Information cont. Portuguese Hungarian Polish 10 Slovak Czech Croatian Regulatory Information cont. Estonian Latvian Lithuanian 11
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2009-10-09 | JBP - Part 15 Class B Computing Device Peripheral | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2009-10-09
|
||||
1 | Applicant's complete, legal business name |
LG Electronics USA
|
||||
1 | FCC Registration Number (FRN) |
0020917688
|
||||
1 | Physical Address |
1000 Sylvan Avenue
|
||||
1 |
Englewood Cliffs, New Jersey 07632
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
T******@TIMCOENGR.COM
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
BEJ
|
||||
1 | Equipment Product Code |
42LH260HUA
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
K******** H********
|
||||
1 | Title |
Director, Standards & Compliance
|
||||
1 | Telephone Number |
201-4********
|
||||
1 | Fax Number |
201-8********
|
||||
1 |
k******@lge.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 11/22/2009 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | JBP - Part 15 Class B Computing Device Peripheral | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | LCD TV MONITOR | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
GUMI UNIVERSITY EMC CENTER
|
||||
1 | Name |
T******** P****
|
||||
1 | Telephone Number |
82-54********
|
||||
1 | Fax Number |
82-54********
|
||||
1 |
t******@gumi.ac.kr
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15B |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC