MFL68045804 Warranty & Customer Service Warranty : 1 year Manufacture Date : On the product Customer Service : www.lg.com Made in Vietnam LIGHTING GATEWAY USER'S MANUAL MANUEL D'UTILISATION WARNING / AVERTISSEMENT
- Violation of warnings may lead to serious injury or death. Use the rated power. Turn power off before installing the product. Do not install the product near a fire. Do not expose the product to water.
- Le non-respect des avertissements peut entraner des blessures graves ou la mort. Utilisez la puissance nominale. Dsactivez l'alimentation avant d'installer le produit. N'installez pas le produit prs d'une source de chaleur. N'exposez pas le produit l'eau. CAUTION / ATTENTION
- Violation of precautions may lead to light injury or product damage. Do not install on an uneven surface. Do not disassemble or deform. Do not install nearby inflammable materials. Do not expose to direct sunlight or moisture.
- Le non-respect des avertissements peut entraner des blessures graves ou la mort. Installez le produit sur une surface plane. Ne pas dmonter ou dformer le produit. Ne pas installer le produit proximit de matriaux inflammables. Ne pas exposer le produit directement la lumire du soleil ni la moisissure. ENGLISH Dimensions 29 mm Installation 1 2 3 90 mm 1. Connect the DC cable to the adapter. 2. Connect the DC adapter to gateway. And then, connect the wireless router to the gateway with LAN cable. 3. Place the gateway on the proper place and make connect power. Ensure the Power LED is on. Note : Initialization 70 mm LED Operation Power LED It turns on when power is applied. LAN LED It turns on when the LAN cable is normally connected and the gateway communicates through the LAN. Wireless Communication LED It blinks regularly when the gateway is connected through wireless communication. Troubleshooting The Power LED do not turn on. :
Check whether the DC cable is properly connected to both the gateway and the adapter. The LAN LED do not turn on. :
Check whether the LAN cable is properly connected. The Wireless communication LED blinks too fast. :
Contact the service center or dealer that you purchased this product. Factory reset Press and hold the reset button for over 10 seconds. After 10 seconds, all LEDs begin flashing 3 times. Specifications Frequency Wireless range Operating voltage Current consumption Operating temperature Operating condition Weight Dimensions (WHD) 2405.0 ~ 2480.0 MHz line of sight 98 ft (30 m) 5 V DC (from the adapter) Max. 400 mA
-20 ~ +40 For Indoor use only 70 g 2.8x3.5x1.1 (70 mm x 90 mm x 29 mm) FRANAIS Dimensions 29 mm Installation 1 2 3 90 mm 1. Branchez le cble CC l'adaptateur. 2. Branchez l'adaptateur CC la passerelle. Par aprs, profiter le cble rseau branchez routeur Sans Fil la passerelle, si ncessaire 3. Placez la passerelle un endroit adquat et branchez l'alimentation. Vrifiez que le voyant d'alimentation est allum Remarque : Initialisation 70 mm Fonctionnement des LED Voyant DEL d'alimentation Il s'allume lorsque le produit est mis sous tension. Voyant DEL rseau Il s'allume lorsque le cble rseau est connect normalement et la communication depuis la passerelle se fait via le rseau local. Voyant DEL de communication sans fil Il clignote rgulirement lorsque la passerelle est connecte via une communication sans fil. Dpannage G LED'i yanmyor. :
DC kablosunun hem a geidine hem de adaptre dzgn balandndan emin olun. G LED'i yanmaz. :
LAN kablosunun dzgn balandndan emin olun. Kablosuz iletiim LED'i ok hzl yanp snyor. :
Servis merkeziyle ya da rn satn aldnz bayi ile iletiim kurun. Model name FCC ID IC 9GW97185D6 BEJ9GW97185D6 2703H-9GW97185D6 Federal Communications Commission (FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation of the device of the device. CAN ICES-3(B)/NMB-3(B) FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment and For indoor use only, use outdoors or in other modes not covered by this manual may violate the FCC regulation and violate the user authority to use the product. FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. Equipment used at position in which the spaces between human body and antenna exceeded 20 cm Industry Canada (IC) Statement Industry Canada Statement :
This device complies with RSS Standard of the Industry Canada Rules. Operation is subject to the following two conditions :
1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device. IC Radiation Exposure Statement :
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator
& your body NOTE : THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. Rinitialisation d'usine Maintenez le bouton de rinitialisation enfonc pendant plus de 5 secondes. Aprs puis, voyant de flash Puissance 3 fois. Caractristiques Frquence Porte sans fil Tension de fonctionnement Consommation lectrique Temprature de fonctionnement Conditions de fonctionnement Poids 2405,0~2480,0 MHz Porte optique : 30 m (98 ft) 5 V CC ( partir d'un adaptateur.) Max. 400 mA de -20 40 (-4 104) Pour utilisation en intrieur uniquement 70 g (2,5 oz) Dimensions (LxHxP) 70 mm x 90 mm x 29 mm (2,8 x 3,5 x 1,1) Avis de la Federal Communications Commission (FCC) Vous tes avis(e) que les changements ou les modifications apports cette unit, non expressment approuvs par la partie responsable de la conformit, pourraient annuler le droit accord lutilisateur dexploiter cet quipement. Cet quipement a t test et jug conforme aux limites sappliquant un appareil numrique de la classe B, conformment la partie 15 de la rglementation de la FCC. Ces limites ont t labores pour offrir une protection raisonnable contre les interfrences nuisibles dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre de lnergie de radiofrquence et, sil nest pas install et utilis conformment aux instructions du fabricant, peut provoquer des interfrences dangereuses pour les communications radio. Toutefois, rien ne garantit labsence dinterfrences dans une installation particulire. Si cet quipement provoque des interfrences nuisibles en ce qui concerne la rception radio ou tlvision, ce qui peut tre dtermin par la mise hors tension, puis sous tension de lquipement, vous tes invit(e) essayer de corriger les interfrences en prenant les mesures suivantes :
- Rorientez ou dplacez lantenne rceptrice.
- Augmentez la distance qui spare lquipement et le rcepteur.
- Branchez lquipement dans la prise dun circuit diffrent de celui auquel est branch le rcepteur. Consultez le revendeur ou un technicien radio / tlvision expriment pour obtenir de laide. Avertissement FCC Tout changement ou toute modification apport(e) cette unit non expressment approuv(e) par la partie responsable de la conformit pourrait annuler le droit accord lutilisateur dexploiter cet quipement. Cet appareil ne convient qu une utilisation intrieure. Une utilisation extrieure ou d'autres faons non couvertes par ce manuel peut constituer un non-respect de la rglementation FCC et porter atteinte aux droits de lutilisateur utiliser ce produit. nonc FCC sur lexposition aux rayonnements de radiofrquence :
Cet appareil est conforme aux limites d'exposition aux rayonnements pour un environnement non contrl. Les utilisateurs suivront les instructions dexploitation spcifiques pour rpondre aux exigences de conformit sur lexposition aux radiofrquences. Notice d'Industrie Canada (IC) Avis d'Industrie Canada :
Cet appareil est conforme la norme CNR dIndustrie Canada des rglements d'Industrie Canada. Son fonctionnement est sujet aux deux conditions suivantes :
1) Cet appareil ne doit pas provoquer d'interfrences et 2) Cet appareil doit accepter toutes les interfrences, y compris celles pouvant entraner son dysfonctionnement. Avis d'Industrie Canada sur l'exposition aux rayonnements Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. REMARQUE : LE FABRICANT N'EST PAS RESPONSABLE DES INTERFRENCES RADIOLECTRIQUES CAUSES PAR DES MODIFICATIONS NON AUTORISES APPORTES CET APPAREIL. DE TELLES MODIFICATIONS POURRAIT ANNULER L'AUTORISATION ACCORDE L'UTILISATEUR DE FAIRE FONCTIONNER L'APPAREIL.