SPJ2BW WIRELESS ACTIVE SUBWOOFER 15 SPJ2B-W UserMan Users Manual

 

OWNERS MANUALWirelessSound BarPlease read this manual carefully before operating your set and retain it for future reference. MODEL SJ2 (SJ2, SPJ2B-W)www.lg.com*MFL00000000*2 Safety Information CAUTION DO NOT OPEN RISK OF ELECTRIC SHOCK CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus. WARNING: Do not install this equipment in a confined space such as a book case or similar unit. CAUTION: Do not use high voltage products around this product. (ex. Electrical swatter) This product may malfunction due to electrical shock. CAUTION: No naked flame sources, such as lighted candles, should be placed on the apparatus. CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings shall be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a built-

in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturers instruction has been adhered to. Getting StartedGetting Started1 3 This device is equipped with a portable battery or accumulator. Safety way to remove the battery from the equipment: Remove the old battery or battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement systems batteries and accumulators. The battery should not be exposed to excessive heat such as sunshine, fire or the like. CAUTION concerning the Power Cord The Power Plug is the disconnecting device. In case of an emergency, the Power Plug must remain readily accessible. Check the specification page of this owners manual to be certain of the current requirements. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your device, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the device, and have the cord replaced with an exact replacement part by an authorized service center. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the device. NOTICE: For safety marking information including product identification and power supply ratings, please refer to the main label on the bottom or the other surface of the product. Getting StartedGetting Started1 4 Symbols Refers to alternating current (AC).

~

0 Refers to direct current (DC). Refers to class II equipment. 1 Refers to stand-by.

!

Refers to ON (power). Refers to dangerous voltage. Getting StartedGetting Started1 Table of Contents 1 Getting Started 2 6 6 6 7 8 8 9 10 Safety Information Unique features Introduction Symbols used in this manual Remote control Front panel Rear panel About LED condition Installing the sound bar Connecting to your TV Using an OPTICAL cable 2 Connecting 11 Wireless subwoofer connection 12 12 13 Optional equipment connection 13 13 14 14 14 15 OPT. IN connection PORT. IN connection USB connection Compatible USB devices USB device requirement Playable file 5 3 Operating Basic operations 16 16 USB operation 16 Other operations 16 16 16 17 17 18 19 Using BLUETOOTH technology 19 DRC (Dynamic Range Control) Turn off the sound temporarily Using your TV remote control Auto power down AUTO POWER On/Off Auto function change Listening to music stored on the Bluetooth devices 21 21 21 Sound adjustment Setting the surround mode Adjust the woofer level settings 4 Troubleshooting 22 22 23 Troubleshooting General NOTES to use wireless 5 Appendix Trademarks and licenses 24 25 Specifications 26 Maintenance 26 Handling the unit Table of Contents12345 6 Unique features Introduction Symbols used in this manual

, Note Indicates special notes and operating features.

> Caution Indicates cautions for preventing possible damages from abuse. Auto power down This unit supports to turn off by itself for saving energy consumption. Portable In Listen to music from your portable device.

(MP3 player, Notebook, Smart phone, etc..) BLUETOOTH Listens to music stored on your Bluetooth device. USB playback Listens to music stored on your USB device. Getting StartedGetting Started1 Remote control Replacement of battery 7 a 1 (Power) : Switches the unit ON or OFF F : Selects the function. OPTICAL : Selects the optical function.

(Mute) : Mutes the sound. STANDARD : Selects standardized sound. BASS BLAST: Reinforces the treble, bass and surround sound effect. VOL o/p : Adjusts speaker volume. b DRC ON/OFF :

- Turns on or off DRC function.

(Page 16)

- Controls this unit using TV remote.

(Page 16) WOOFER LEVEL o/p : Adjusts sound level of subwoofer. AUTO POWER ON/OFF :

- Turns on or off AUTO POWER function. (Page 17)

- Turns on or off the Bluetooth connection lock function. (Page 20) C/V (Skip) :

- Skips Fast backward or Forward. dM (Play/Pause) :

- Starts playback.

- Pauses playback. Remove the battery cover on the rear of the remote control, and insert battery with correctly. matched and Getting StartedGetting Started1 8 Front panel A Remote sensor B Standby LED (Red) C Function LED (White) Rear panel D The buttons are located on the rear. A o/p (Volume) : Adjusts volume level 1 (Standby) F (Function) : Selects the function.

(USB) : Connect to a USB device. B C PORT.IN (Portable) : Connect to a Portable device. D OPT. IN (Optical) : Connect to an Optical device. Getting StartedGetting Started1 9 About LED condition LED Condition Description OPTICAL LED turns on. OPTICAL function is selected. USB LED turns on. USB function is selected. USB LED blinks. Paused USB playback. Bluetooth LED turns on. Paired with Bluetooth device. Bluetooth LED blinks. Waiting for Bluetooth connection. PORTABLE LED turns on. PORTABLE function is selected.

, Note y When you press any button, standby LED (Red) on the main unit blinks. y When you press y When this unit reaches minimum volume, standby LED (Red) turns on for 2 seconds. y When this unit reaches maximum volume, standby LED (Red) turns on for 2 seconds. y When you press volume (o/p) button continually, standby LED (Red) blinks quickly.

(Mute) button, standby LED (Red) blinks slowly. Getting StartedGetting Started1 10 Installing the sound bar You can hear the sound by connecting the unit to the other device : TV, Blu-ray disc player, DVD player, etc. Place the unit in front of the TV and connect it to the device you want. (Page 12 - 15)

> Caution y For best performance of wireless connection such as Bluetooth or wireless subwoofer, do not install the unit on Metallic furniture because wireless connection communicates through a module positioned on the bottom of the unit. y Be careful not to make scratches on the surface of the Unit / Subwoofer when installing or moving them. Getting StartedGetting Started1 Wireless subwoofer connection LED indicator of wireless subwoofer LED Color Status Green

(Blink) Green Red Off (No display) Attempting to make connection. The connection is completed. The wireless subwoofer is in standby mode or the connection is failed. The power cord of wireless subwoofer is disconnected. Setting up the wireless subwoofer for the first time 1. Connect the power cord to the subwoofer and plug the power cord into a power outlet. 2. Turn on the main unit : The sound bar and wireless subwoofer will be automatically connected.

- Green LED on the rear of wireless subwoofer turns on. Manually pairing wireless subwoofer When your connection is not completed, you can check red LED on the wireless subwoofer and the wireless subwoofer does not make sound. To solve the problem, follow the steps below. 11 1. Press Pairing button on the rear of the wireless subwoofer.

- The green LED on the rear of the wireless subwoofer blinks quickly. 2. Turn on the main unit. 3. Pairing is completed.

- The green LED on the rear of the wireless subwoofer turns on.

, Note y It takes a few seconds (and may take longer) for the main unit and the subwoofer to communicate with each other and make sounds. y The closer the main unit and the subwoofer, the better sound quality. It is recommended to install the main unit and the subwoofer as close as possible and avoid the cases below.

- There is an obstacle between the main unit and the subwoofer.

- There is a device using same frequency with this wireless connection such as a medical equipment, a microwave or a wireless LAN device.

- Keep the sound bar and the subwoofer away from the device (ex. wireless router, microwave oven, etc.) over 1 m to prevent wireless interference.

ConnectingConnecting2 12 Connecting to your TV Using an OPTICAL cable 1. Connect the OPT. IN jack on the back of the unit to OPTICAL OUT jack on the TV using an OPTICAL cable. Optical cable 2. Select the input source to Optical by pressing OPTICAL button on the remote control or F button on the unit repeatedly.

, Note y Before connecting the optical cable, be sure to remove the protection plug cover if your cable has the cover. y You can enjoy the TV audio through the speakers of this unit. In the case of some TV models, you must select the external speaker option from the TV menu. (For details, reference your TV user manual.) y Set up the sound output of TV to listen to the sound through this unit :

TV setting menu [ [Sound] [ [TV Sound output] [ [External speaker (Optical)]

y Details of TV setting menu vary depending on the manufacturers or models of your TV. ConnectingConnecting2 Optional equipment connection OPT. IN connection Connect an optical output jack of external devices to the OPT. IN jack. 13 PORT. IN connection Portable cable Optical cable To the digital optical output jack of external device 1. Connect the OPT. IN jack on the back of the unit to OPTICAL OUT jack of your external device. 2. Select the input source to Optical by pressing OPTICAL button on the remote control or F button on the unit repeatedly. 3. Listen to sound.

, Note Before connecting the optical cable, be sure to remove the protection plug cover if your cable has the cover. Listening to music from your portable player The unit can be used to play the music from many types of portable players or external devices. 1. Connect the portable player to the PORT. IN connector of the unit by using 3.5 mm stereo cable. 2. Select the input source to PORTABLE by pressing F button on the remote control or unit repeatedly. 3. Turn on the portable player or external device and start playing it. ConnectingConnecting2 14 USB connection Connect USB memory device to the USB port on the back of the unit. For more information of playing files on a USB, refer to the page 16. Removing the USB Device from the unit. 1. Choose a different function/mode. 2. Remove the USB device from the unit. Compatible USB devices y MP3 Player : Flash type MP3 player. y USB Flash Drive : Devices that support USB 1.1. y The USB function of this unit does not support some USB devices. USB device requirement y Devices which require additional program installation connected to a computer, are not supported. y Do not extract the USB device while in operation. y For a large capacity USB, it may take longer than a few minutes to be searched. y To prevent data loss, back up all data. y This unit is not supported when the total number of files is 1,000 or more. y The units USB Port can not be connected to PC. The unit can not be used as a storage device. y The exFAT file system is not supported on this unit. (FAT16/FAT32 systems are available.) y Depending on some devices, it may not available to recognize the followings on this unit.

- External HDD

- Card readers

- Locked devices

- Hard type USB devices

- USB hub

- Using USB extension cable

- iPhone/iPod/iPad

- Android device ConnectingConnecting2 Playable file Sampling Frequency MP3 : within 32 to 48 kHz WMA : within 32 to 48 kHz Bitrate MP3 : within 80 to 320 kbps WMA : within 56 to 128 kbps y Maximum files : Under 999 y Maximum directories : Under 99 y A protected file by DRM (Digital rights management) cannot be played on the unit. y Video files in the USB storage device can not be played. y Depending on the performance of your USB device, playback may not work well. 15

, Note y Folders and files on the USB are recognized as below.

: Folder

: File C D E b H I d a c A B F G J y File will be played from file $A to file $J one by one. y Files will be played in order recorded and it may be different depending on the record circumstances. y You can't see a folder or file through this unit. ConnectingConnecting2 16 Basic operations Other operations USB operation 1. Connect the USB device to the USB port. 2. Select the input source to USB by pressing F button on the remote control or unit repeatedly. DRC (Dynamic Range Control) Make the sound clear when the volume is turned down and prevent sudden increase of sound (Dolby Digital only). This function turns on or off when you press DRC ON/OFF. To Playback Pause Do this Press dM. During playback, press dM. During playback, press V on the remote control to go to the next file. Playing less than 2 seconds, press C on the remote control to go to the previous file. Playing after 3 seconds, press C on the remote control to go to the beginning of the file. This unit memorizes a current song which is played before changing the function or turning off the unit. Skip to the next/

previous file Resume playback

, Note y The resume point may be cleared when you pull out the power cord or removing the USB device from the unit. y If the USB function is not working, check the USB function is selected. y When you pause the USB playback, USB LED on the main unit blinks. Turn off the sound temporarily

(Mute) to mute your unit. To cancel it, Press press

(Mute) again on the remote control or change the volume level. Using your TV remote control You can control some functions of this unit by your TV remote control even by other companys product. Controllable functions are volume up/down and mute. Press and hold DRC ON on the remote control for about 2 seconds. To turn off this function, press and hold DRC OFF about 2 seconds.

, Note y Supported TV brands LG Panasonic Philips Samsung Sharp Sony Toshiba Vizio y Make sure that the sound output of your TV is set to [External speaker]. y Depending on the remote control, this function may not work well. y This function does not operate on LG TV's magic remote control. OperatingOperating3 17

, Note y After the unit is turned on by AUTO POWER function, it will be automatically turned off if there is no signal for a certain period of time from the external device. y If you turned off the unit directly, it cannot be turned on automatically by AUTO POWER function. However the unit can be turned on by AUTO POWER function when optical signal comes in after 5 seconds of no signal. y Depending on the connected device, this function may not operate. y If you disconnect Bluetooth connection by this unit, some Bluetooth devices try to connect to the unit continually. Therefore it is recommended to disconnect the connection before turn off the unit. y When you turn on this unit for the first time, Auto Power function is turned on status. y To use this function, the main unit must be registered in paired devices list of Bluetooth device. y You can set the AUTO POWER function only when this unit is turned on. Auto power down This unit will turn itself off to save electric consumption if the main unit is not connected to an external device and has not been used for 15 minutes. This unit also turns off after six hours if the Main unit has been connected to another device using the analog input. (Ex : Portable, etc..) How to disconnect the wireless network connection or the wireless device Set up the AUTO POWER ON/OFF function to off and turn off the unit. AUTO POWER On/Off This unit automatically turns on by an input source :

Optical or Bluetooth. When you turn on your TV or an external device connected to this unit, this unit recognizes the input signal and select the suitable function. You can hear the sound from your device. If you try to connect your Bluetooth device, this unit turns on and the unit will be connected your Bluetooth device. This function turns on or off you press AUTO POWER ON/OFF. OperatingOperating3 18 Auto function change This unit recognizes input signals such as Optical, Bluetooth and Portable and then changes suitable function automatically. When optical signal comes in When you turn on the external device connected to this unit by an optical cable, this unit change the function to optical. You can hear the sound from your device. When you try to connect Bluetooth device When you try to connect your Bluetooth device to this unit, Bluetooth function is selected. Play your music on the Bluetooth device. When connect a Portable device When you connect your portable device using a portable cable, this unit changes the function to Portable. You can hear the music from your device.

, Note y To change to optical function, it needs 5 seconds of no signal. y If the Bluetooth connection lock function is set, Bluetooth connection will be only available on Bluetooth function.

(Page 20) OperatingOperating3 Using BLUETOOTH technology About Bluetooth Bluetooth is wireless communication technology for short range connection. The sound may be interrupted when the connection interfered by the other electronic wave or you connect the Bluetooth in the other rooms. Connecting individual devices under Bluetooth wireless technology does not incur any charges. A mobile phone with Bluetooth wireless technology can be operated via the Cascade if the connection was made via Bluetooth wireless technology. y Available Devices : Smart phone, MP3 player, Notebook, etc.. y Version : 4.0 y Codec : SBC Bluetooth Profiles In order to use Bluetooth wireless technology, devices must be able to interpret certain profiles. This unit is compatible with following profile. A2DP (Advanced Audio Distribution Profile) 19 Listening to music stored on the Bluetooth devices Pairing your unit and Bluetooth device Before you start the pairing procedure, make sure the Bluetooth feature is turned on in to your Bluetooth device. Refer to your Bluetooth devices user guide. Once a pairing operation is performed, it does not need to be performed again. 1. Select the input source to Bluetooth by pressing F button on the remote control or unit repeatedly.

- Bluetooth LED will blink. 2. Operate the Bluetooth device and perform the pairing operation. When searching for this unit with the Bluetooth device, a list of the devices found may appear in the Bluetooth device display depending on the type of Bluetooth device. Your unit appears as LG SJ2 (XX).

, Note y XX means the last two digits of Bluetooth address. For example, if your unit has a Bluetooth address such as 9C:02:98:4A:F7:08, you will see LG SJ2 (08) on your Bluetooth device. y Depending on the Bluetooth device type, some device have a different pairing way. Enter the PIN code (0000) as needed. 3. When this unit is successfully connected with your Bluetooth device, Bluetooth LED will turn on. 4. Listen to music. To play a music stored on your Bluetooth device, refer to your Bluetooth devices user guide. OperatingOperating3 BLUETOOTH connection lock (BT lock) You can limit Bluetooth connection to only Bluetooth function to prevent unintended Bluetooth connection. Press and hold AUTO POWER ON on the remote control for about 2 seconds to turn on this function in Bluetooth function. To turn off this function, press and hold AUTO POWER OFF on the remote control for about 2 seconds in Bluetooth function.

, Note Even if you set up Bluetooth connection lock to On, this sound bar turns on by Auto Power function. Turn off Auto Power function to prevent it. 20

, Note y When using Bluetooth technology, you have to make a connection between the unit and the Bluetooth device as close as possible and keep the distance. However it may not work well in the cases below :

- There is an obstacle between the unit and the Bluetooth device.

- There is a device using same frequency with Bluetooth technology such as a medical equipment, a microwave or a wireless LAN device. y You should connect your Bluetooth device to this unit again when you restart it. y The sound may be interrupted when the connection interfered by the other electronic wave. y Pairing is limited one Bluetooth device per one unit and multi-pairing is not supported. y Depending on the type of the device, you may not be able to use the Bluetooth function. y You can enjoy Bluetooth function using Smart phone, MP3 player, Notebook, etc.. y The more distance between the unit and the Bluetooth device, the lower the sound quality becomes. y Bluetooth connection will be disconnected when the unit is turned off or the Bluetooth device gets far from the unit. y When Bluetooth connection is disconnected, connect the Bluetooth device to the unit again. y When the unit is not connected with Bluetooth device, Bluetooth LED will blink. y When you connect a Bluetooth device

(iOS device etc.) to this unit or operate the device, the volume level can be synchronized between the two devices. y You can control a Bluetooth device using C/V (Skip) and dM (Play/Pause) buttons on the remote control. OperatingOperating3 21 Adjust the woofer level settings You can adjust the sound level of woofer by pressing WOOFER LEVEL o/p button.

, Note When the woofer level reaches maximum or minimum, standby LED (Red) on the main unit turns on for 2 seconds. Sound adjustment Setting the surround mode This system has two pre-set surround sound fields. You can select a desired sound mode by using each sound mode button. Sound effect STANDARD BASS BLAST Description You can enjoy optimized sound. Reinforces the treble, bass and surround sound effect.

, Note y In some of sound effect mode, some speakers, theres no sound or low sound. It depends on the mode of sound and the source of audio, it is not defective. y You may need to reset the sound effect mode, after switching the input, sometimes even after the sound file changed. OperatingOperating3 22 Troubleshooting General PROBLEM The unit does not work properly. CAUSE & CORRECTION y Turn off the power of this unit and the connected external device

(TV, Woofer, DVD-player, Amplifier, etc.) and turn them on again. y Disconnect the power cord of this unit and the connected external device

(TV, Woofer, DVD-player, Amplifier, etc.) and then try connecting again. y Previous setting may not be saved when device power is shut off. No Power y The power cord is unplugged. Plug in the power cord. y Check whether electricity failed. Check the condition by operating other electronic devices. y Incorrect input source is selected. Check the input source and select the correct input source. No sound y The mute function is activated. Press

(Mute) or adjust the volume level to cancel the mute function. y When you are using connection with an external device

(set top box, Bluetooth device etc.), adjust volume level of the device. No woofer sound y The power cord of woofer is not connected. Plug the power cord into the wall outlet securely. y Pairing between the unit and woofer gets disconnected. Connect the unit and woofer. (Page 11) y The remote control is too far from the unit. Operate the remote control within about 7 m. y There is an obstacle in the path of the remote control and the unit. Remove the obstacle. y The batteries in the remote control is exhausted. Replace the batteries with new one. y Check connection of the external device such as TV, DVD/Blu-Ray player or Bluetooth device. y Depending on the connected device, this function may not operate. y Turn off the Bluetooth connection lock function. (Page 20) The remote control does not work properly. The AUTO POWER function does not work. The unit does not connect with Bluetooth device TroubleshootingTroubleshooting4 23 PROBLEM CAUSE & CORRECTION When you feel the output sound of the unit is low. Check the details below and adjust the unit according to them. y Switch [ON] state of DRC function to [OFF] by using remote controller. y With the sound bar connected with TV, change the AUDIO DIGITAL OUT setting on TV Setup Menu from [PCM] to [AUTO] or [BITSTREAM]. y With the sound bar connected with Player, change the AUDIO DIGITAL OUT setting on Player Setup Menu from [PCM] to [PRIMARY PASS-THROUGH] or

[BITSTREAM]. NOTES to use wireless PROBLEM CAUSE & CORRECTION This device may have wireless interference. y Wireless may not operate normally in weak signal area. y Please install the device close enough to wireless subwoofer. y Do not install the device on metal furniture for optimum performance. Bluetooth device may malfunction or make noise in the following cases. y When any part of your body contact the transceiver of the Bluetooth device or sound bar. y When there is an obstacle or wall or the device is installed in a secluded spot. y When there is a device(a wireless LAN, a medical equipment or a microwave) using same frequency, make the distance between the products as far away as possible each other. y When to connecting the device to the Bluetooth device, make the distance between the products as close as possible each other. y When the device gets too far from the Bluetooth device, the connection is disconnected and also malfunction may occur. TroubleshootingTroubleshooting4 24 Trademarks and licenses All other trademarks are trademarks of their respective owners. Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories. The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by LG Electronics is under license. Other trademarks and trade names are those of their respective owners. AppendixAppendix5 25 Specifications General Power requirements Power consumption Refer to the main label. Refer to the main label. Networked standby : 0.5 W under

(If all network ports are activated.) Approx. 660 mm x 56 mm x 99 mm with foot 5 C to 35 C 5 % to 90 %

5 V 0 500 mA 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz Dimensions (W x H x D) Operating temperature Operating humidity Bus Power Supply Available Digital Input Audio Sampling Frequency Available Digital Input Audio format Dolby Audio, PCM Inputs OPT. IN (Digital audio in) PORT. IN (Portable in) Amplifier (RMS Output power) Total Front Subwoofer Wireless subwoofer Power requirements Power consumption Type Impedance Rated Input Power Max. Input Power Dimensions (W x H x D) 0 dBfs, Optical jack x 1 0.4 Vrms (3.5 mm stereo jack) x 1 160 W RMS 30 W RMS x 2 (8 at 1 kHz, 10% THD) 100 W RMS (3 at 80 Hz, 10% THD) Refer to the main label on the subwoofer. Refer to the main label on the subwoofer. 1 Way 1 Speaker 3 100 W RMS 200 W RMS Approx. 185.5 mm x 303 mm x 205 mm y Designs and specifications are subject to change without prior notice. AppendixAppendix5 26 Maintenance Handling the unit When shipping the unit Please save the original shipping carton and packing materials. If you need to ship the unit, for maximum protection, re-pack the unit as it was originally packed at the factory. Keeping the exterior surfaces clean y Do not use volatile liquids such as insecticide spray near the unit. y Wiping with strong pressure may damage the surface. y Do not leave rubber or plastic products in contact with the unit for a long period of time. Cleaning the unit To clean the player, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit. AppendixAppendix5 E N G L I S H SIMPLE MANUAL Wireless Sound Bar Please read this manual carefully before operating your set and retain it for future reference. To view the instructions of advanced features, visit http://www.lg.com and then download Owner's Manual. Some of the content in this manual may differ from your unit. MODEL SJ2

*MFL00000000*

www.lg.com FCC RF Radiation Exposure Statement : This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20 cm (7.8 inches) between the antenna and your body. Users must follow the specific operating instructions for satisfying RF exposure compliance. FCC Radio Frequency Interference Requirements :

High power radars are allocated as primary users of the 5.725 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. This device cannot be co-located with any other transmitter. Responsible Party :

LG Electronics USA, Inc. 1000 Sylvan Ave Englewood Cliffs, NJ 07632 Tel: 1-800-243-0000 WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

y Reorient or relocate the receiving antenna. y Increase the separation between the equipment and the receiver. y Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. y Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference and

(2) this device must accept any interference received, including interference that may cause undesired operation of the device. Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Front Panel 1 Subwoofer Connection The buttons are located on the rear. Standby Place the wireless subwoofer near the sound bar and follow steps below. a Connect the power cord of wireless subwoofer and sound bar to the outlet. b Turn on the main unit :

The sound bar and wireless subwoofer will be automatically connected. The subwoofer's green LED turns on. Selects Function. Subwoofer Connection Manually

/

Adjusts Volume. Rear Panel If the subwoofer does not make sound, try to connect manually. a Press Pairing button on the rear of the wireless subwoofer. y The green LED on the rear of wireless subwoofer blinks quickly. b Turn on the main unit. c Pairing is completed. y The green LED on the rear of wireless subwoofer turns on.

(USB) Connect to a USB device. PORT. IN (Portable) Connect to a Portable device. OPT. IN (Optical) Connect to an Optical device. Keep the sound bar and the subwoofer away from the device (ex. wireless router, microwave oven, etc.) over 1 m to prevent wireless interference.

Remote control STANDARD/BASS BLAST: Selects the sound effect. DRC ON/OFF : Makes comfortable sound at Dolby Digital.. WOOFER LEVEL +/-: Adjusts the volume level of subwoofer. AUTO POWER ON/OFF: Automatically turns on by an input source. Replacement of battery 2 TV Connection a Connect the sound bar to the TV using an Optical cable. b Set up [External Speaker (Optical)] on your TV setting menu. TV Additional Device Connection a Connect to the external device as follows.

(Set-top Box, Player etc.) TV b Set the input source by pressing OPTICAL on the remote control or pressing F on the unit repeatedly. Additional Information Specification Power requirements Refer to the main label. Power consumption Refer to the main label. Dimensions

(W x H x D) Approx. 660 mm x 56 mm x 99 mm

(26 inch x 2.2 inch x 3.9 inch) With foot 5 V 0 500 mA Bus Power Supply

(USB) Amplifier

(Total RMS Output power) Design and specifications are subject to change without notice. 160 W RMS LG Customer Information Center 1-800-243-0000 1-888-865-3026 USA, Consumer USA, Commercial Register your product Online!

www.lg.com Printed in China E N G L I S H SIMPLE MANUAL Wireless Sound Bar Please read this manual carefully before operating your set and retain it for future reference. To view the instructions of advanced features, visit http://www.lg.com and then download Owner's Manual. Some of the content in this manual may differ from your unit. MODEL SJ2

*MFL00000000*

www.lg.com SJ2.ACANLLK_SIM_ENG_.indd 1 2017-03-16 5:21:46 Front Panel 1 Subwoofer Connection The buttons are located on the rear. Standby Place the wireless subwoofer near the sound bar and follow steps below. a Connect the power cord of wireless subwoofer and sound bar to the outlet. b Turn on the main unit :

The sound bar and wireless subwoofer will be automatically connected. The subwoofer's green LED turns on. Selects Function. Subwoofer Connection Manually

/

Adjusts Volume. Rear Panel

(USB) Connect to a USB device. PORT. IN (Portable) Connect to a Portable device. OPT. IN (Optical) Connect to an Optical device. If the subwoofer does not make sound, try to connect manually. a Press Pairing button on the rear of the wireless subwoofer. y The green LED on the rear of wireless subwoofer blinks quickly. b Turn on the main unit. c Pairing is completed. y The green LED on the rear of wireless subwoofer turns on. Keep the sound bar and the subwoofer away from the device (ex. wireless router, microwave oven, etc.) over 1 m to prevent wireless interference.

SJ2.ACANLLK_SIM_ENG_.indd 2 2017-03-16 5:21:48 2 TV Connection a Connect the sound bar to the TV using an Optical cable. b Set up [External Speaker (Optical)] on your TV setting menu. TV Additional Device Connection a Connect to the external device as follows.

(Set-top Box, Player etc.) TV b Set the input source by pressing OPTICAL on the remote control or pressing F on the unit repeatedly. Remote control STANDARD/BASS BLAST: Selects the sound effect. DRC ON/OFF : Makes comfortable sound at Dolby Digital.. WOOFER LEVEL +/-: Adjusts the volume level of subwoofer. AUTO POWER ON/OFF: Automatically turns on by an input source. Replacement of battery Additional Information Specification Power requirements Refer to the main label. Power consumption Refer to the main label. Dimensions

(W x H x D) Approx. 660 mm x 56 mm x 99 mm With foot 5 V 0 500 mA Bus Power Supply

(USB) Amplifier

(Total RMS Output power) Design and specifications are subject to change without notice. 160 W RMS SJ2.ACANLLK_SIM_ENG_.indd 3 2017-03-16 5:21:49 Industry Canada Statement This device complies with Industry Canadas licence-

exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. CAN ICES-3 (B)/NMB-3 (B) IC Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (7.8 inches) between the antenna & your body. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. WARNING

[For product having the wireless function using 5 GHz frequency bands]

(i) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and LG Customer Information Center Centre dinformation la clientle de LG 1-888-542-2623 CANADA Register your product Online!

Enregistrez votre produit en ligne!

www.lg.com SJ2.ACANLLK_SIM_ENG_.indd 4 2017-03-16 5:21:49 F R A N A S I MANUEL SIMPLIFI Barre de son sans fil Veuillez lire attentivement ce manuel avant dutiliser votre appareil et conservez-le pour le consulter ultrieurement. Pour voir les instructions des fonctionnalits avances, visitez le site http://www.lg.com et tlchargez le manuel dutilisation. Certains lments de ce manuel pourraient ne pas correspondre votre appareil, selon son modle. MODLE SJ2

*MFL00000000*

www.lg.com SJ2.ACANLLK_SIM_FRE(CANADA)_.indd 1 2017-03-16 5:24:27 Panneau avant Les touches sont situes larrire. Veille Permet de choisir la fonction

/

Permet de rgler le volume Panneau arrire

(USB) Se branche un appareil USB PORT.IN (Portable) Se branche un appareil portable OPT. IN (Optique) Se branche un appareil optique 1 Connexion du caisson de basses Placez le caisson de basses sans fil prs de la barre de son et suivez les tapes ci-dessous. a Branchez le cordon dalimentation du caisson de basses sans fil sur la prise. b Mettez la barre de son sous tension :

La barre de son et le caisson de basses sans fil se connectent automatiquement. Le voyant vert du caisson de basses sallume. Connexion manuelle du caisson de basses Si le subwoofer ne produit pas de son, essayez de le connecter manuellement. a Appuyez sur la touche Pairing l'arrire du caisson de basses sans fil. y Le voyant DEL vert l'arrire du caisson de basses sans fil se met clignoter rapidement. b Allumez l'appareil principal. c Le jumelage est termin. basses sans fil s'allume. y Le voyant DEL vert l'arrire du caisson de Pour viter les interfrences des quipements sans fil, la barre de son et le caisson de basses doivent tre une distance dau moins 1 m par rapport un autre appareil (comme le routeur sans fil, le four micro-ondes, etc.).

SJ2.ACANLLK_SIM_FRE(CANADA)_.indd 2 2017-03-16 5:24:29 2 Raccordement au tlviseur Tlcommande a Reliez la barre de son au tlviseur laide du cble optique. b Configurez le [Haut-parleur externe (Optique)]

depuis le menu de configuration de votre tlviseur. TV Raccordement dun priphrique supplmentaire a Raccordez le priphrique externe comme il est indiqu sur le schma ci-dessous.

(botier dcodeur, lecteur, etc.) TV b Dfinissez la source dentre en appuyant sur OPTICAL sur la tlcommande ou sur F sur lappareil plusieurs reprises. STANDARD/BASS BLAST : Permet de slectionner leffet sonore. DRC ON/OFF : procure un confort d'coute en Dolby Digital. WOOFER LEVEL +/- : Permet de rgler le volume du caisson de basses. AUTO POWER ON/OFF : Se met en marche automatiquement grce une source dentre. Remplacement des piles Informations supplmentaires Caractristiques Exigences relatives lalimentation Consommation dnergie Dimensions

(L x H x P) Se reporter ltiquette principale. Se reporter ltiquette principale. Environ 660 mm x 56 mm x 99 mm Avec les pieds 5 V 0 500 mA Alimentation bus

(USB) Amplificateur

(puissance de sortie R.M.S. totale) La conception et les caractristiques peuvent faire lobjet de modifications sans notification pralable. 160 W RMS SJ2.ACANLLK_SIM_FRE(CANADA)_.indd 3 2017-03-16 5:24:30 AVERTISSEMENTS

(Pour un produit dot de la fonction sans fil utilisant la bande de frquences de 5 GHz.) i) Pour les appareils munis dantennes amovibles, le gain maximal dantenne autoris pour les appareils utilisant la bande de 5 725 5 850 MHz doit tre conforme la limite de la p.i.r.e. spcifie pour lexploitation point point et lexploitation non point point, selon le cas. Avis dIndustrie Canada Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est assujettie aux deux conditions suivantes :

1) Lappareil ne doit pas produire dinterfrences;

2) Lutilisateur de lappareil doit accepter toute interfrence, mme si elle est susceptible de nuire au fonctionnement de lappareil. CAN ICES-3 (B)/NMB-3 (B) Avis dIndustrie Canada sur lexposition aux rayonnements Cet appareil est conforme aux limites dexposition aux rayonnements dIndustrie Canada pour un environnement non contrl. Cet appareil doit tre install de faon maintenir une distance minimale de 20 cm (7,8 po) entre lantenne et lutilisateur. REMARQUE : LE FABRICANT NEST PAS RESPONSABLE DES INTERFRENCES RADIOLECTRIQUES CAUSES PAR DES MODIFICATIONS NON AUTORISES APPORTES CET APPAREIL. DE TELLES MODIFICATIONS POURRAIENT ANNULER LAUTORISATION DEXPLOITATION ACCORDE LUTILISATEUR DE LAPPAREIL. Le dispositif rencontre l'exemption des limites courantes d'evaluation dans la section 2.5 de RSS 102 et la conformite a l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformite de rf. LG Customer Information Center Centre dinformation la clientle de LG 1-888-542-2623 CANADA Register your product Online!

Enregistrez votre produit en ligne!

www.lg.com SJ2.ACANLLK_SIM_FRE(CANADA)_.indd 4 2017-03-16 5:24:30 L O A P S E PRECAUCIN RIESGO DE CHOQUE ELCTRICO. NO ABRIR. PRECAUCIN: PARA REDUCIR EL RIESGO DE CHOQUE ELCTRICO, NO RETIRE LA CUBIERTA (O LA PARTE POSTERIOR). EN EL INTERIOR NO HAY PIEZAS REPARABLES POR EL USUARIO. SOLICITE AYUDA AL PERSONAL DE SERVICIO CALIFICADO. El smbolo del rayo con punta de flecha dentro de un tringulo equiltero pretende alertar al usuario de la presencia de voltaje peligroso no aislado en el interior del armario del producto que puede tener la magnitud suficiente para constituir un riesgo de choque elctrico para las personas. El signo de exclamacin dentro de un tringulo equiltero pretende alertar al usuario de la presencia de instrucciones importantes (de servicio) para el funcionamiento y mantenimiento en la informacin que acompaa al producto. ADVERTENCIA:

y PARA REDUCIR EL RIESGO DE INCENDIO O CHOQUE ELCTRICO, NO EXPONGA ESTE PRODUCTO A LA LLUVIA NI A LA HUMEDAD. y No instale el equipo en un espacio cerrado, como en un librero o mueble similar. PRECAUCIN:

y No usar equipos de alto voltage cerca de este producto. (ej. Matamoscas electrnico). Este producto puede funcionar incorrectamente debido a las descargas elctricas. y No coloque sobre el aparato fuentes de calor con llama, como velas encendidas. y No obstruya ninguno de los orificios de ventilacin. Instale conforme a las instrucciones del fabricante. Las ranuras y orificios del armario cumplen un propsito de ventilacin y aseguran el funcionamiento adecuado del producto, a fin de protegerlo de un posible sobrecalentamiento. Los orificios no deben obstruirse. El producto no debe colocarse sobre una cama, sof, tapete o una superficie similar. Este producto no debe colocarse en una instalacin empotrada, como un librero o estante, a menos que haya una buena ventilacin y se respeten todas las instrucciones del fabricante. El enchufe de corriente es el dispositivo de desconexin. En caso de emergencia, el enchufe de corriente debe permanecer de fcil acceso. El aparato no debe exponerse al agua (goteo o salpicaduras) y no debe colocar sobre el aparato objetos llenos de lquidos, como floreros. y y y Para informacin sobre seguridad, se incluye la identificacin del producto y los ndices de abastecimiento. Por favor consulte la etiqueta principal en la base o en la parte posterior del aparato. Este dispositivo est equipado con una batera o acumulador porttil. Forma segura de retirar la batera del equipo: retire la batera o bateras antiguas siguiendo el orden inverso al de instalacin. Para evitar contaminar el medioambiente y provocar posibles daos a la salud pblica, las bateras viejas deben llevarse a los puntos de recogida designados. no se deshaga de las bateras con la basura normal. Es recomendable utilizar los sistemas locales de recogida de bateras y acumuladores. La batera no debe exponerse a calor excesivo como el del sol, el fuego o fuente similar. Para los modelos que usan un adaptador Use slo el adaptador CA suministrado con este dispositivo. No utilice una fuente de alimentacin de otro dispositivo o de otro fabricante. El uso de otros cables o unidades de alimentacin puede causar daos a la unidad e invalidar la garanta. Instrucciones importantes de seguridad Lea estas instrucciones. 1. 2. Guarde estas instrucciones. Siga todas las advertencias. 3. 4. Siga todas las instrucciones. 5. No use este aparato cerca del agua. 6. 7. No obstruya ninguna salida de ventilacin. Instale de acuerdo con Limpie nicamente con un pao seco. las instrucciones del fabricante. 8. No instale cerca de fuentes de calor como radiadores, registros de calefaccin, estufas u otros aparatos (incluyendo amplificadores) que produzcan calor. 9. Respete el uso de la conexin del tomacorriente polarizado o con conexin a tierra. Un tomacorriente polarizado tiene una cuchilla ms ancha que la otra. Un tomacorriente con tierra tiene dos cuchillas y una pata para tierra. La cuchilla ms ancha o la pata para tierra sirven como proteccin. Si el tomacorriente proporcionado no se ajusta a su tomacorriente, pngase en contacto con un electricista para que lo reemplace. 10. Proteja el cable de alimentacin para que no caminen sobre l o quede atorado, particularmente en contactos, en receptculos y en el punto por donde sale del aparato. 11. Solamente use los aditamentos / accesorios especificados por el fabricante. 12. Use nicamente con el carro, estante, trpode, soporte o mesa especificados por el fabricante o que haya sido vendido junto con el aparato. Cuando use un carro, tenga cuidado cuando mueva la unidad / carro para evitar accidentes por vuelcos. 13. Desconecte este aparato durante tormentas elctricas o cuando no vaya a usarlo por perodos prolongados. 14. Haga que todo el mantenimiento sea realizado solamente por personal tcnico cualificado.Solicite mantenimiento cuando el aparato haya sufrido cualquier tipo de dao, por ejemplo, si el cable de alimentacin o el tomacorriente estn daados, cuando se haya derramado lquido sobre el aparato o hayan cado objetos sobre l, cuando haya sido expuesto a lluvia o humedad, cuando no funcione con normalidad o cuando haya sufrido una cada. Safety Information Consignes de scurit Informacin de seguridad

*MBM65227008*

www.lg.com H S I L G N E CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING:

y TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. y Do not install this equipment in a confined space such as a book case or similar unit. CAUTION:

y Do not use high voltage products around this product. (ex. Electrical swatter) This product may malfunction due to electrical shock. y No naked flame sources, such as lighted candles, should be placed on the apparatus. y Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings shall be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturers instruction has been adhered to. The Power Plug is the disconnecting device. In case of an emergency, the Power Plug must remain readily accessible. The apparatus shall not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus. For safety marking information including product identification and supply ratings, please refer to the main label on the bottom or the other surface of the product. y y y This device is equipped with a portable battery or accumulator. Safety way to remove the battery or the battery from the equipment:

Remove the old battery or battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement systems batteries and accumulators. The battery shall not be exposed to excessive heat such as sunshine, fire or the like. For models using an adapter Only use the AC adapter supplied with this device. Do not use a power supply from another device or another manufacturer. Using any other power cable or power supply may cause damage to the device and void your warranty. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the Follow all instructions. manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. AVIS RISQUE DE CHOC LECTRIQUE NE PAS OUVRIR ATTENTION : POUR RDUIRE LE RISQUE DE CHOC LECTRIQUE, NENLEVEZ PAS LE COUVERCLE (OU LA PARTIE ARRIRE). IL NY A PAS DE COMPOSANTS SUSCEPTIBLES DTRE RPARS PAR LUTILISATEUR LINTRIEUR DE CET APPAREIL. CONFIEZ LE SERVICE TECHNIQUE DU PERSONNEL QUALIFI. Le symbole dclair avec une flche, dans un triangle quilatral, avertit lutilisateur de la prsence dune tension dangereuse non isole lintrieur du botier du produit et qui pourrait tre dune puissance suffisante pour causer une lectrocution. Le point dexclamation lintrieur dun triangle quilatral avertit lutilisateur de la prsence dimportantes directives suivre concernant le fonctionnement ou la maintenance

(entretien) dans le manuel accompagnant ce produit. Cet appareil est quip dune batterie transportable ou de piles rechargeables. Retrait sans danger de la batterie ou des piles de lappareil :

Pour retirer la batterie ou les piles usages, procdez dans lordre inverse de leur insertion. Pour empcher toute contamination de lenvironnement et tout danger pour la sant des tres humains et des animaux, la batterie ou les piles usages doivent tre mises au rebut dans le conteneur appropri un point de collecte prvu pour leur recyclage. Ne pas jeter la batterie ou les piles usages avec les autres dchets. Recycler toujours les batteries et piles rechargeables usages. Ne pas exposer la pile une chaleur extrme telle que la lumire du soleil, le feu ou autre source du mme genre. Pour les modles utilisant un adaptateur Utilisez exclusivement ladaptateur CA fourni avec cet appareil. Nutilisez pas une source dalimentation dun autre appareil ou dun autre fabricant. Lutilisation dun autre cble dalimentation ou dune autre source dalimentation peut endommager le lappareil et annuler votre garantie. Consignes de scurit importantes F R A N A I S AVERTISSEMENT :

y AFIN DVITER LES RISQUES DINCENDIE ET DLECTROCUTION, GARDER CE PRODUIT LABRI DE LA PLUIE ET DE LHUMIDIT. y Ninstallez pas cet appareil dans un espace restreint tel quune bibliothque ou tout autre meuble similaire. ATTENTION :

y Nutilisez pas dquipement lectrique haute tension prs du tlviseur (comme un tue-mouches lectrique). Cela pourrait entraner un mauvais fonctionnement du produit. y Aucune source de flamme nue, telles quune bougie allume, ne doit tre place sur lappareil. y Ne pas bloquer les ouvertures daration. Installer lappareil en respectant les directives du fabricant. Les fentes et les ouvertures de lappareil ont t conues pour assurer une bonne ventilation et un bon fonctionnement du produit en le protgeant de toute surchauffe. Les ouvertures ne doivent jamais tre bloques; lobstruction pourrait survenir en installant le produit sur un lit, un canap, un tapis ou sur toute autre surface similaire. Cet appareil ne doit pas tre install dans un espace ferm comme une bibliothque ou une tagre moins quune ventilation particulire soit assure ou que les directives du fabricant lautorisent. La fiche dalimentation sert dbrancher lappareil. En cas durgence, elle doit tre facilement accessible. Lappareil ne doit pas tre expos leau (par immersion ou claboussure) et aucun objet rempli de liquide, comme un vase, ne devrait tre plac sur lappareil. y y y Pour obtenir des informations sur le marquage de scurit, lidentification du produit et les valeurs nominales dalimentation, reportez-vous ltiquette principale au-dessous de lappareil ou sur un autre ct. Lire les directives. 1. 2. Conserver ces directives. 3. Respecter tous les avertissements. 4. 5. Ne pas utiliser ce produit prs de leau. 6. Nettoyer seulement avec un chiffon propre. 7. Ne pas obstruer les ouvertures de ventilation. Installer conformment Suivre toutes les directives. aux directives du fabricant. 8. Ne pas linstaller prs de sources de chaleur comme un radiateur, une cuisinire ou dautres appareils semblables (y compris des amplificateurs) qui produisent de la chaleur. 9. Ne pas contourner la fonction scuritaire de la prise polarise ou de mise la terre. Une prise polarise est dote de deux fiches dont lune est plus large que lautre. Une prise de mise la terre est dote de deux fiches et dune fiche de mise la terre. La fiche la plus large ou la fiche de mise la terre contribuent votre scurit. Si la prise nentre pas dans la prise murale, consulter un lectricien pour la remplacer. 10. Protger le cordon dalimentation contre le pitinement ou le pincement, particulirement prs de la fiche, des prises et des points de sortie du produit. 11. Utiliser seulement les accessoires recommands par le fabricant. 12. Utiliser seulement des chariots, des supports, des trpieds, des fixations ou tables recommands par le fabricant ou vendus avec lappareil. Si un chariot est utilis, faire attention au moment de dplacer lappareil pour viter quil ne bascule. 13. Dbrancher cet appareil pendant les orages ou lorsquil nest pas utilis pendant de longues priodes. 14. Consulter du personnel qualifi pour la rparation. Un entretien est requis lorsque le produit est endommag de quelque faon que ce soit

: dommage au cordon dalimentation ou la fiche, dversement de liquide ou objets insrs lintrieur, exposition du produit la pluie ou lhumidit, fonctionnement normal ou chute.