all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Users manual | Users Manual | 1.42 MiB | ||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | Operational Description | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | Users manual | Users Manual | 1.42 MiB |
Warning WWarning arning
/CAUTION WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of suffi-
cient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appli-
ance. WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. FCC NOTICE A Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compli-
ance could void the users warranty. CAUTION:
Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized mod-
ification could void the users warranty. COMPLIANCE:
The responsible party for this products compliance is:
LG Electronics U.S.A., Inc 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 1-800-243-0000 http://www.lgusa.com 2 Plasma Monitor Safety Instructions Safety Instructions Safety Instructions IMPORTANT SAFETY INSTRUCTIONS Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the appa-
ratus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled Important Safety Instructions. The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturers option, a picture or drawing that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction :
1. Read these instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampli-
2. Keep these instructions. Owner's Manual fiers)that produce heat. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accor-
dance with the manufacturers instructions. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace-
ment of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the man-
ufacturer. Owners Manual 3 Safety Instructions 12. Use only with the cart, stand, tripod, bracket, or table 15. CAUTION concerning the Power Cord :
specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. PORTABLE CART WARNING 13. Unplug this apparatus during lightning storms or when unused for long periods of time. Most appliances recommend they be placed upon a dedi-
cated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch cir-
cuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deteri-
oration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, 14. Refer all servicing to qualified service personnel. such as being twisted, kinked, pinched, closed in a door, or Servicing is required when the apparatus has been dam-
walked upon. Pay particular attention to plugs, wall outlets, aged in any way, such as power-supply cord or plug is dam-
and the point where the cord exits the appliance. aged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, 16. Outdoor Use Marking :
does not operate normally, or has been dropped. WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Appliance To Rain Or Moisture. 17. Wet Location Marking :
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. 4 Plasma Monitor Contents Contents Safety Instructions . 2~4 Timer Menu Options Contents Clock Setup . 26 On/Off Timer Setup . 26 Auto Sleep . 27 Sleep Timer . 27 Special Menu Options Child Lock . 28 ISM Method . 28 Tile mode . 29 Low power . 30 XD demo . 30 Screen Menu Options Auto Adjustment . 31 Manual Configure . 31 Selecting XGA mode . 32 Picture Size Control . 32 Screen Position . 29 Initializing . 33 External Control Device Setup . 34~39 IR Code . 40~41 Troubleshooting Checklist . 42~43 Troubleshooting Checklist . 44 Specifications . 45 Introduction Features Of This monitor . 6 Accessories . 7 Controls and Connection Options . 8~9 Remote Control Key Functions . 10 Installation Desktop Pedestal Installation . 11 External Equipment Connections VCR Setup . 12 Cable TV Setup . 13 External A/V Source Setup . 13 DVD Setup . 14 DTV Setup . 15 PC Setup . 16~17 Operation Turning on the Monitor . 18 Menu Language Selection . 18 On Screen Menus Selection . 19 Picture Menu Options Picture Status Memory (PSM) . 20 Manual Picture Control
. 20 Color Status Memory (PSM) . 21 Manual Color Temperature Control . 21 XD . 22 Picture Reset . 22 Advanced - Cinema 3:2 Pull down mode . 23 Advanced - Black level . 23 Sound Menu Options Sound Status Memory (SSM) . 24 Manual Sound Control . 24 AVL (Auto Volume Leveler) . 25 Balance . 25 TV Speaker on/off setup . 25 After reading this manual, keep it handy for future reference. Owners Manual 5 Introduction Introduction Introduction Features Of This Monitor Features Of This Monitor What is a Plasma Monitor ?
If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon. 160 - Wide angle range of vision Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room. Wide Screen The screen of the Plasma Display is 71" so wide that your viewing experience is as if you are in a theater. Multimedia Connect your plasma display to a PC and you can use it for conferencing, games, and internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously. Versatile The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs would not fit. The Plasma Monitor Manufacturing Process: Why minute colored dots may be present on the Plasma Monitor screen The Plasma Display Panel which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the Plasma Monitor manufacturing process. Several minute colored dots visible on the screen should be accept-
able. This also occurs in other Plasma Monitor manufacturers' products and the tiny dots appearing does not mean that this Plasma Monitor is defective. Thus a few cell defects are not sufficient cause for the Plasma Monitor to be exchanged or returned. Our production technology is designed to minimize cell defects during the manufacture and operation of this product. Cooling Fan Noise In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the Plasma Monitor is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the Plasma Monitor. The fan noise doesn't have any negative effect on the Plasma Monitor's efficiency or reliability. The noise from these fans is nor-
mal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the Plasma Monitor to be exchanged or returned. 6 Plasma Monitor Introduction Accessories Accessories Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. Owners Manual 1.5V 1 . 5 V Batteries D-sub 15 pin cable Power Cord POWER AV INPUT SLEEP PSM ARC AUTO 1 4 7
*
2 5 8 0 3 6 9
*
MENU EXIT VOL SET VOL MUTE
*
Remote Control Owners Manual 7 Introduction Controls Controls
- This is a simplified representation of front panel.
- This picture shown below may be somewhat different from your monitor. 3 4 5 6 1 2 ON/OFF 7 1.Power Standby Indicator Illuminates red in standby mode, Illuminates green when the Set is turned on. 2. Remote Control Sensor 3. VOLUME (FF,GG) Buttons EE, DD Buttons 4. MENU Button 5. INPUT SELECT Button 6. Main Power Button Switches the set on from standby or off to standby. 8 Plasma Monitor Connection Options Connection Options
- Connection panels shown may be somewhat different from your Monitor. Introduction 10 REMOTE CONTROL IN RS-232C
(CONTROL&SERVICE) HDMI/DVI IN RGB AUDIO
(RGB/DVI) COMPONENT IN VIDEO L-AUDIO-R VIDEO AV IN L-AUDIO-R OUT IN IN OUT 1 2 AV OUT EXTERNAL SPEAKER S-VIDEO R L 1 2 3 4 5 1 2 3 4 REMOTE CONTROL IN Connect your wired remote control. RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC. HDMI/DVI IN Connect a HDMI signal to 1(DVI) or 2. Or DVI(VIDEO) signal to the 1(DVI) port with a DVI to HDMI cable. RGB INPUT Connect the set output connector from a PC to the appropriate input port. RGB OUTPUT You can watch the RGB signal on another set, connect RGB OUTPUT to another sets PC input port. 5 AUDIO (RGB/DVI) Connect the monitor output from a PC to the appropriate input port. 6 6 7 8 7 8 9 COMPONENT IN Connect a component video/audio device to these jacks. AV OUTPUT Connect a second Set or monitor. VIDEO IN Connect audio/video output from an external device to these jacks. S-VIDEO Connect S-Video out from an S-VIDEO device. 9 EXTERNAL SPEAKER (8 ohm output) Connect to optional external speaker(s).
* For further information, refer to Speaker & Speaker Stand manual. 10 POWER CORD SOCKET This Monitor operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the Monitor on DC power. Owners Manual 9 Introduction Remote Control Key Functions Remote Control Key Functions
- When using the remote control, aim it at the remote control sensor on the monitor.
- Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press the key again as necessary. AV Selects: AV, Component 1-2, RGB, HDMI/DVI input sources. POWER Turns your monitor or any other programmed equipment on or off, depending on mode. INPUT Selects: AV, Component 1-2, RGB, HDMI/DVI input sources. SLEEP Sets the Sleep Timer. PSM Adjusts the factory preset picture according to the room. ARC Changes the picture format. AUTO Automatic adjustment function NUMBER buttons Dosent work for monitor mode.
*Not functional MENU Brings up the main menu to the screen. EXIT Clears all on-screen displays and returns to monitor viewing from any menu. THUMBSTICK (Up/Down/Left/Right/SET) Navigate the on-screen menus and adjust the system set-
tings to your preference. VOLUME UP/DOWN Increases/decreases the sound level. MUTE Switches the sound on or off.
*Not functional POWER AV INPUT SLEEP PSM ARC AUTO 1 4 7
*
2 5 8 0 3 6 9
*
MENU EXIT VOL SET VOL MUTE
*
Installing Batteries Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -). Install two 1.5V AA batteries. Dont mix old or used batteries with new ones. Replace cover. 10 Plasma Monitor Installation Installation Desktop Pedestal Installation Desktop Pedestal Installation For proper ventilation, allow a clearance of 4inches on each side from the wall. Introduction This picture shown below may be somewhat different from your monitor. Power Supply Short-circuit Breaker GROUNDING Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Owners Manual 11 Installation External Equipment Connections External Equipment Connections NOTE: Not all cables shown are included with the plasma display. VCR Setup VCR Setup
- To avoid picture noise (interference), leave an adequate distance between the VCR and monitor.
- Use the ISM Method (on the Special menu) feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. Connection Option 1. Connect the audio and video cables from the VCR's output jacks to the set input jacks, as shown in the figure. When connecting the set to VCR, match the jack colors
(Video = yellow, Audio Left = white, and Audio Right = red). If you connect an S-VIDEO output from VCR to the S-VIDEO input, the picture quality is improved; compared to connect-
ing a regular VCR to the Video input. 2. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.) 3. Select the input source with using the INPUT button on the remote control. Do not connect to both Video and S-
Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work. NENT IN 1 2 L-AUDIO-R VIDEO AV IN L-AUDIO-R AV OUT EXTERNAL SPEAK S-VIDEO R ANT OUT OUTPUT SWITCH ANT IN S-VIDEO VIDEO L R VCR ENT IN 1 2 L-AUDIO-R VIDEO AV IN L-AUDIO-R AV OUT EXTERNAL SPEAKER S-VIDEO R L ANT OUT OUTPUT SWITCH L R VIDEO S-VIDEO ANT IN VCR 12 Plasma Monitor Installation Cable TV Setup TV Setup Cable
- After subscribing to a cable monitor service from a local provider and installing a converter, you can watch cable TV program-
ming. The monitor cannot display monitor programming unless a TV tuner device or cable TV converter box is connected to the Monitor.
- For further information regarding cable monitor service, contact your local cable TV service provider(s). How to connect 1. Connect the audio and video cables from the Cable Box's output jacks to the monitor input jacks, as shown in the figure. When connecting the monitor to a Cable Box, match the jack colors
(Video = yellow, Audio Left = white, and Audio Right = red). Or, connect the Euro scart socket of the Cable box to the Euro scart socket of the set. ENT IN 1 2 L-AUDIO-R VIDEO AV IN L-AUDIO-R AV OUT EXTERNAL SPEAKER S-VIDEO R L How to use 1. Use the INPUT button on the remote control to select AV. 2. Select your desired channel with the remote control for cable box.
(R) AUDIO (L) VIDEO TV VCR OUTPUT SWITCH 3 4 RF Cable Cable Box External A/V Source Setup A/V Source Setup External How to connect 1. Connect the audio and video cables from the external equipment's output jacks to the monitor input jacks, as shown in the figure. When connecting the monitor to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). Or, connect the Euro scart socket of the External A/V to the Euro scart socket of the set. How to use 1. Use the INPUT button on the remote control to select AV. 2. Operate the corresponding external equipment. Refer to external equipment operating guide. COMPONENT IN VIDEO L-AUDIO-R VIDEO AV IN L-AUDIO-R 1 2 AV OUT EXTERNAL SPEAKER S-VIDEO R L VIDEO L R Owners Manual 13 Installation DVD Setup DVD Setup UDIO B/DVI) COMPONENT IN VIDEO L-AUDIO-R VIDEO DIO-R VIDEO 1 2 AV OU AV OUT AV IN L-AUDIO-R EXTER R S-VIDEO MOTE ROL IN RS-232C
(CONTROL&SERVICE) HDMI/DVI IN RGB OUT IN IN OUT Y PB PR L R DVD L R AUDIO S-VIDEO HDMI-DVD OUTPUT How to connect 1. Connect the DVD video outputs to the COMPONENT (Y, PB, PR) or HDMI IN 1(DVI) jacks and connect the DVD audio outputs to the AUDIO INPUT jacks on the monitor, as shown in the figure. 2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the monitor and connect the DVD audio out-
puts to the AUDIO INPUT jacks on the monitor, as shown in the figure. How to use 1. Turn on the DVD player, insert a DVD. 2. Use the INPUT button on the remote control to select Component 1, Component 2, or HDMI/DVI. (If connected to S-VIDEO, select the AV external input source.) 3. Refer to the DVD player's manual for operating instructions. Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown. Component ports of the Monitor Video output ports of DVD player Y Y Y Y Y PB PR Pb B-Y Cb PB Pr R-Y Cr PR 14 Plasma Monitor Installation DTV Setup DTV Setup
- To watch digitally broadcast programs, purchase and connect a digital set-top box.
- This monitor supports HDCP (High-bandwidth Digital Contents Protection) protocol for HDMI/DVI-DTV (480p,720p,1080i, 1080p) mode. AUDIO GB/DVI) COMPONENT IN VIDEO L-AUDIO-R VIDEO E IN RS-232C
(CONTROL&SERVICE) HDMI/DVI IN RGB 1 2 AV OUT OUT IN IN OUT 232C L&SERVICE) OUT IN HDMI/DVI IN RGB AUDIO
(RGB/DVI) IN OUT Y PB PR L R HDMI-DTV OUTPUT Digital Set-top Box DVI-DTV OUTPUT L R How to connect 1. Use the monitors COMPONENT (Y, PB, PR) INPUT, RGB or HDMI IN 1(DVI) to HDMI jack for video connec-
tions, depending on your set-top box connector. Then, make the corresponding audio connections. How to use 1. Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.) 2. Use INPUT on the remote control to select Component 1, Component 2, RGB, or HDMI/DVI. Owners Manual 15 Installation PC Setup PC Setup
- This monitor provides Plug and Play capability, meaning that the PC adjusts automatically to its settings. The monitor sends configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel
(DDC) protocol.
- The monitor perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. In this case, change the screen scanning rate for the graphic card. RS-232C ROL&SERVICE) HDMI/DVI IN RGB AUDIO
(RGB/DVI) COMPO VIDEO RS-232C
(CONTROL&SERVICE) HDMI/DVI IN RGB AUDIO
(RGB/DVI) C VID OUT IN IN OUT OUT IN IN OUT RGB OUTPUT AUDIO DVI-PC OUTPUT AUDIO How to connect 1. To get the best picture quality, adjust the PC graphics card to a 1600x1200, 60Hz. 2. Use the monitors RGB INPUT or HDMI IN 1(DVI) port for video connections, depending on your PC connector. If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of either RGB IN or HDMI IN 1(DVI) to display the PC on the monitor. If the graphic card on the PC does output analog and digital RGB simultaneously, set the monitor to either RGB or HDMI1/DVI;
(the other mode is set to Plug and Play automatically by the monitor.) 3. Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required. How to use 1. Turn on the PC and the monitor. 2. Turn on the display by pressing the POWER button on the monitor's remote control. 3. Use the INPUT button on the remote control to select RGB or HDMI/DVI. 4. Check the image on your monitor. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. NOTES: Avoid keeping a fixed image on the monitor's screen for a long period of time. The fixed image may become perma-
nently imprinted on the screen. Use the Orbiter screen saver when possible. The synchronization input form for Horizontal and Vertical frequencies is separate. 16 Plasma Monitor Monitor Display Specifications (RGB-PC / HDMI/DVI-PC Mode) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) Installation 640x480 720x400 640x480 800x600 832x624 1024x768 1280x720 1280x768 1360x768 1366x768 1280x1024 1600x1200 31.469 31.468 31.469 37.500 43.269 37.879 46.875 53.674 49.725 48.363 60.023 68.68 44.442 47.00 47.72 47.00 63.981 79.98 75.00 70.08 70.08 59.94 75.00 85.00 60.31 75.00 85.06 74.55 60.00 75.02 85.00 60.00 60.00 60.00 60.00 60.00 75.00 60.00 Owners Manual 17 Operation Operation Operation TTurning on the Monitor urning on the Monitor Turning on the Monitor just after installation 1. Connect power cord correctly. At this moment, the Monitor is switched to standby mode. 2. Press the INPUT or button on the Monitor or press the POWER, INPUT button on the remote control and then the Monitor will switch on. Menu Language Selection Menu Language Selection
- The menus can be shown on the screen in the selected language. First select your language. 1. Press the MENU button and then use DD / EE button to select the SPECIAL menu. 2. Press the GG button and then use DD / EE button to select Language. 3. Press the GG button and then use DD / EE button to select your desired language. From this point on, the on-screen menus will be shown in the language of your choice. 4. Press the ENTER button to save. Press the MENU button to return to the previous menu. 18 Plasma Monitor Operation On Screen Menus Selection On Screen Menus Selection Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual. 1. Press the MENU button and then use DD / EE button to select the each menu. 2. Press the GG button and then use DD / EE / FF / GG button to display the available menus. PSM CSM XD Advanced Reset Auto config. Manual config. XGA Mode ARC Reset Language Child lock ISM Method Set ID Tile mode Logo light XD Demo SSM AVL Balance Speaker Clock Off time On time Auto sleep Owners Manual 19 Picture Menu Options Picture Menu Options Picture Status Memory (PSM) Picture Status Memory (PSM)
- PSM adjusts the Monitor for the best picture appearance.
- When adjusting Picture menu options (contrast, brightness, color, sharpness, and tint) manually, PSM automatically changes to User. 1. Press the PSM button repeatedly to select the picture appearance setup option as shown below. Dynamic Standard Mild User 1 User2 You can also select Dynamic, Standard, Mild, User 1 or User 2 in the PICTURE menu. Dynamic, Standard, and Mild settings are preset for optimum picture quality at the factory and cannot be changed. Manual Picture Control (PSM - User option) option) Manual Picture Control (PSM -
- You can adjust picture contrast, brightness, colour, sharpness, and tint to the levels you prefer. PSM CSM XD Advanced Reset Dynamic Standard Mild User1 User2 G User1 Contrast Brightness Color Sharpness Tint 85 50 50 50 0 G R G 1. Press the MENU button and then use DD / EE button to select the PICTURE menu. 2. Press the GG button and then use DD / EE button to select the desired picture option (Contrast, Brightness, Color, Sharpness or Tint). 3. Press the GG button and then use FF / GG button to make appropriate adjustments. 4. Press the ENTER button to save the new settings. 20 Plasma Monitor Color Status Memory (CSM) Color Status Memory (CSM)
- To initialize values (reset to default settings), select the Cool option. PSM CSM XD Advanced Reset PSM CSM XD Advanced Reset G Cool Normal Warm User 1. Press the MENU button and then use DD / EE button to select the PICTURE menu. 2. Press the GG button and then use DD / EE button to select CSM. 3. Press the GG button and then use DD / EE button to select either Cool, Normal, Warm, or User. 4. Press the ENTER button to save the new settings. Manual Color TTemperature control (CSM -
Manual Color emperature control (CSM - User option) option)
- You can adjust red, green, or blue to any color temperature you prefer. PSM CSM XD Advanced Reset G Warm Normal Cool User User Red Green Blue 0 0 0 G 1. Press the MENU button and then use DD / EE button to select the PICTURE menu. 2. Press the GG button and then use DD / EE button to select CSM. 3. Press the GG button and then use DD / EE button to select User. 4. Press the GG button and then use DD / EE button to select Red, Green or Blue. 5. Use the FF / GG button to make appropriate adjustments. The adjustment range of Red, Green and Blue is -10 ~ +10. 6. Press the ENTER button to save the new settings. Owners Manual 21 XD (Picture Improvement TTechnology) echnology) XD (Picture Improvement
- XD is LG Electronics unique picture improving technology to display a real HD source through an advanced digital signal pro-
cessing algorithm.
- When selecting PSM options (Dynamic, Standard, Mild), XD is automatically changed to Auto.
- When selecting PSM options (User 1 or User 2), you can choose the Auto / Manual.
- When selecting the Manual, you can adjust the XD Contrast, XD color and XD Noise. PSM CSM XD Advanced Reset PSM CSM XD Advanced Reset Auto Manual G XD Contrast On On XD Color XD NR Off MPEG NR 0 1. Press the MENU button and then use DD / EE button to select the PICTURE menu. 2. Press the GG button and then use DD/ EE button to select XD. 3. Press the GG button and then use DD / EE button to select either Auto or Manual. Selecting the Manual a. Press the GG button and then use FF / GG button to select XD Contrast, XD Color or XD Noise. I XD Contrast: Optimizing the contrast automatically according to the brightness of the reflection. I XD Color: Adjusting the colors of the reflection automatically to reproduce as closely as possible to the natural colors. I XD NR: Removing the noise up to the point where it does not damage the original picture. I MPEG NR: You can select it to reduce the picture noise which may appear on the screen while watching the AV. b. Use the DD / EE button to select On or Off. 4. Press the ENTER button to save the new settings. Picture Reset Picture Reset
- Use to quickly reset all the Video menu options to their original factory preset values. PSM CSM XD Advanced Reset PSM CSM XD Advanced Reset G To set 1. Press the MENU button and then use DD / EE button to select the PICTURE menu. 2. Press the GG button and then use DD / EE button to select Reset. 3. Press the GG button to reset the Picture menu options to original values. 22 Plasma Monitor Advanced - Cinema 3:2 Pull down Mode Advanced - Cinema 3:2 Pull down Mode
- Set up the TV for the best picture appearance for viewing movies.
- When you operate Cinema 3:2 Mode (3:2 Pull-Down Mode or Cinema Correction Mode), the TV will adjust 24 fps video from movies to 30 fps video for display.
- This feature operates only in Analog, AV, and Component 480i mode. PSM CSM XD Advanced Reset PSM CSM XD Advanced Reset G Cinema Black level Off Low 1. Press the MENU button and then use DD / EE button to select the PICTURE menu. 2. Press the GG button and then use DD / EE button to select Advanced. 3. Press the GG button and then use DD / EE button to select Cinema. 4. Press the GG button and then use DD / EE button to select On or Off. 5. Press the ENTER button to save the new settings. Advanced - Black (Darkness) Level Advanced - Black (Darkness) Level
- Adjusting the contrast and the brightness of the screen using the black level of the screen.
- This feature operates only in AV or HDMI mode. PSM CSM XD Advanced Reset PSM CSM XD Advanced Reset G Cinema Black level Off Low 1. Press the MENU button and then use DD / EE button to select the PICTURE menu. 2. Press the GG button and then use DD / EE button to select Advanced. 3. Press the GG button and then use DD / EE button to select Black level. 4. Press the GG button and then use DD / EE button to select Low or High. I Low: The screen gets darker. I High: The screen gets brighter. 5. Press the ENTER button to save the new settings. Owners Manual 23 Operation Sound Menu Options Sound Menu Options Sound Status Memory (SSM) Sound Status Memory (SSM)
- SSM lets you enjoy the best sound without any special adjustment because the Monitor has the appropriate sound options based on the program content.
- When adjusting sound options (treble, bass) manually, DASP automatically changes to Off. SSM AVL Balance Speaker SSM AVL Balance Speaker G Surround MAX Flat Music Movie Sports User 1. Press the MENU button and then use DD / EE button to select the SOUND menu. 2. Press the GG button and then use DD / EE button to select SSM. 3. Press the GG button and then use DD / EE button to select Surround MAX, Flat, Music, Movie, Sports, or User. 4. Press the ENTER button to save the new settings. Manual Sound Control (SSM - User option) option) Manual Sound Control (SSM -
SSM AVL Balance Speaker Surround MAX Flat Music Movie Sports User G User 120Hz FF G 200Hz 500Hz 1.2KHz 3KHz 7.5KHz 12KHz 1. Press the MENU button and then use DD / EE button to select the SOUND menu. 2. Press the GG button and then use DD / EE button to select the desired sound option (Treble or Bass). 3. Press the GG button and then use FF / GG button to make appropriate adjustments. 4. Press the ENTER button to save the new settings. 24 Plasma Monitor AAVLVL (Auto V
(Auto Volume Leveler) olume Leveler)
- This feature maintains an equal volume level; even if you change channels. SSM AVL Balance Speaker SSM AVL Balance Speaker G On Off Operation 1. Press the MENU button and then use DD / EE button to select the SOUND menu. 2. Press the GG button and then use DD / EE button to select AVL. 3. Press the GG button and then use DD / EE button to select On or Off. 4. Press the ENTER button to save the new settings. Balance Balance
- Adjust the left/right sound of speaker to suit your taste and room situations. SSM AVL Balance Speaker SSM AVL Balance TV Speaker 0 L R 1. Press the MENU button and then use DD / EE button to select the SOUND menu. 2. Press the GG button and then use DD / EE button to select Balance. 3. Press the GG button and then use FF / GG button to make appropriate adjustments. 4. Press the ENTER button to save the new settings. TV Speakers On/Off Setup f Setup TV Speakers On/Of
- Turn the TV speakers off if using external audio equipment. SSM AVL Balance Speaker SSM AVL Balance Speaker G On Off 1. Press the MENU button and then use DD / EE button to select the SOUND menu. 2. Press the GG button and then use DD / EE button to select Speaker. 3. Press the GG button and then use DD / EE button to select On or Off. 4. Press the ENTER button to save the new settings. Owners Manual 25 Operation TTimer Menu Options imer Menu Options Clock Setup Clock Setup
-
If current time setting is wrong, correct the clock setting. Clock Off time On time Auto sleep G
- - : - - - -
Clock Off time On time Auto sleep 1. Press the MENU button and then use DD / EE button to select the TIME menu. 2. Press the GG button and then use DD / EE button to select Clock. 3. Press the GG button and then use DD / EE button to set the hour. 4. Press the GG button and then use DD / EE button to set the minutes. 5. Press the ENTER button to save the new settings. On/Off f TTimer Setup imer Setup On/Of
- Timer function operates only if current time has already been set.
- Off-Timer function overrides On-Timer function if they are set to the same time.
-
If you do not press any button within 2 hours after the monitor turns on with the On Timer function, the monitor will automatically revert to standby mode. Clock Off time On time Auto sleep Clock Off time On time Auto sleep G On Off 6 : 30 AM Volume 17 1. Press the MENU button and then use DD / EE button to select the TIME menu. 2. Press the GG button and then use DD / EE button to select Off time or On time. 3. Press the GG button and then use DD / EE button to select On. To cancel On/Off timer function, select Off. 4. Press the GG button and then use DD / EE button to set the hour. 5. Press the GG button and then use DD / EE button to set the minutes. For only On timer function; Press the GG button and then use DD / EE button to set volume level. 6. Press the ENTER button to save the new settings. 26 Plasma Monitor Operation Auto Sleep Auto Sleep
-
If there is no input signal, the Monitor turns off automatically after 10 minutes. Clock Off time On time Auto sleep Clock Off time On time Auto sleep G On Off 1. Press the MENU button and then use DD / EE button to select the TIME menu. 2. Press the GG button and then use DD / EE button to select Auto sleep. 3. Press the GG button and then use DD / EE button to select On or Off. 4. Press the ENTER button to save the new settings. Sleep TTimer imer Sleep
- The sleep timer turns the Monitor off at a preset time. Note that this setting is cleared when the monitor is turned off. 1. Press the SLEEP button repeatedly to select the number of minutes. First the --- Min option appears on the screen, followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes. 2. When the number of minutes you want is displayed on the screen, press the ENTER button. The timer begins to count down from the number of minutes selected. 3. To check the remaining minutes before the monitor turns off, press the SLEEP or ENTER button once. 4. To cancel the Sleep Timer, press the SLEEP button repeatedly until
--- Min appears. Owners Manual 27 Operation Special Menu Options Special Menu Options Child Lock Child Lock
- The monitor can be set up so that it can only be used with the remote control.
- This feature can be used to prevent unauthorized viewing by disabling the front panel controls.
- This Monitor is programmed to remember which option it was last set to even if you turn the monitor off. Language Child lock ISM Method Set ID Tile mode Low power XD Demo G On Off Language Child lock ISM Method Set ID Tile mode Low power XD Demo 1. Press the MENU button and then use DD / EE button to select the SPECIAL menu. 2. Press the GG button and then use DD / EE button to select Child lock. 3. Press the GG button and then use DD / EE button to select On or Off. When you select On, the display Key lock appears on the screen if any button on the front panel is pressed. W 4. Press the ENTER button to save the new settings. Image Sticking Minimization (ISM) Method Image Sticking Minimization (ISM) Method
- A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost image remaining; even when you change the image. Avoid allowing a fixed or still image to remain on the Monitor's screen for a long period of time. Language Child lock ISM Method Set ID Tile mode Low power XD Demo Language Child lock ISM Method Set ID Tile mode Low power XD Demo G Normal White Wash Orbiter Inversion orb. + Inv. 1. Press the MENU button and then use DD / EE button to select the SPECIAL menu. 2. Press the GG button and then use DD / EE button to select ISM Method. 3. Press the GG button and then use DD / EE button to select either Normal, White wash, Orbiter, or Inversion. Normal If image sticking is never a problem, ISM is not necessary - set this to Normal. White wash White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear completely using White Wash. To return to normal viewing, press the any button. Orbiter Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the image will move every 2 minutes. Inversion Inversion will automatically invert the Plasma Monitor color every 30 minutes. Orb. + Inv. This function Inverts the panel color of the screen and may help prevent ghost image. The panel color is automatically inverted every 30 minutes and the screen will move every 2 minutes. 4. Press the ENTER button to save the new settings. 28 Plasma Monitor Operation TTile Mode ile Mode
- Must be displayed with various other products.
- Must be in a function that can be connected to RS-232C or RGB Out.
-
It is used to enlarge the screen and also used with several products to view screen. Language Child lock ISM Method Set ID Tile mode Low power XD Demo Language Child lock ISM Method Set ID Tile mode Low power XD Demo Tile Mode Natural Tile ID H-Size V-Size H-Position V-Position G off off 1 0 0 FF GG FF GG Reset To set Tile mode and choose Tile alignment and set the ID of the current product to set location. Only after pressing the SET button the adjustments made to the settings will be saved. Tile ID Select the location of the Tile by setting an ID. H Size Adjust the horizontal size of the screen taking into account the size of the bezel. V Size Adjust the vertical size of the screen taking into account the size of the bezel. H-Position Moving the screen position horizontally. V-Position Moving the screen position vertically. Reset Function to initialize and release Tile. All Tile setting are released when selecting Tile recall and the screen returns to Full screen.
- Tile mode : row x column ( r = 1, 2, 3, 4 c = 1, 2, 3, 4)
- 4 x 4 available.
- Configuration of an integration screen is also available as well as configuration of One by one Display.
- Tile mode (product 1 ~ 4) : r(2) x c(2)
- Tile mode (product 1 ~16) : r(4) x c(4) Row Row ID 1 ID 3 ID 2 ID 4 Column ID 1 ID 2 ID 3 ID 4 ID 7 ID 5 ID 8 ID 6 Column ID 9 Owners Manual 29 Low Power Low Power
- Low power reduces the plasma display's power consumption. Language Child lock ISM Method Set ID Tile mode Low power XD Demo Language Child lock ISM Method Set ID Tile mode Low power XD Demo G On Off 1. Press the MENU button and then use DD / EE button to select the SPECIAL menu. 2. Press the GG button and then use DD / EE button to select Low power. 3. Press the GG button and then use DD / EE button to select On or Off. When you select On, the screen darkens. 4. Press the ENTER button to save the new settings. XD Demo XD Demo
- Use it to see the difference between XD Demo on and XD Demo off.
- XD demo is not available for RGB (PC) and HDMI (PC) sources. Language Child lock ISM Method Set ID Tile mode Low power XD Demo Language Child lock ISM Method Set ID Tile mode Low power XD Demo G To start 1. Press the MENU button and then use DD / EE button to select the SPECIAL menu. 2. Press the GG button and then use DD / EE button to select XD Demo. 3. Press the GG button to begin XD Demo. 4. Press the EXIT button to stop XD Demo. 30 Plasma Monitor Screen Menu Options Screen Menu Options Auto Adjustment Adjustment Auto
- RGB (PC) mode only
- Automatically adjusts picture position and minimizes image shaking.
- After adjustment, if the image is still not correct, your set is functioning properly but needs further adjustment.
- The Auto config. and Manual config. are not active in HDMI mode. Auto config. Manual config. XGA Mode ARC Reset Auto config. G To set Manual config. XGA Mode ARC Reset 1. Press the MENU button and then use DD / EE button to select the SCREEN menu. 2. Press the GG button and then use DD / EE button to select Auto config.. 3. Press the GG button to run Auto configure. When Auto config. has finished, OK will be seen on the screen. If the position of the image is still not correct, try Auto adjustment again. 4. In RGB (PC) mode, if the image needs to be adjusted more after using Auto config., you can make further adjustments with the Manual config. option. Manual Configure (RGB-PC mode only) Manual Configure (RGB-PC mode only)
-
If the image still isnt clear after auto adjustment is completed and especially if characters are still jittery, adjust the pic-
ture Phase manually.
- To correct the screen size, adjust Clock. Auto config. Manual config. XGA Mode ARC Reset Auto config. Manual config. G XGA Mode ARC Reset Phase Clock H-Position V-Position 0 0 0 0 1. Press the MENU button and then use DD / EE button to select the SCREEN menu. 2. Press the GG button and then use DD / EE button to select Manual config.. 3. Press the GG button and then use DD / EE button to to select Phase, Clock, H-Position or V-Position. 4. Use the FF / GG button to make appropriate adjustments. The Phase adjustment range is 0 ~ 63. The Clock adjustment range is -128 ~ +128. 5. Press the ENTER button to save. Owners Manual 31 Operation Selecting XGA modemode Selecting XGA
- To see a normal picture, match the resolution of XGA mode (1024x768, 1280x768, 1360x768, 1366x768) with the selection for XGA mode in the SCREEN menu. Auto config. Manual config. XGA Mode ARC Reset Auto config. Manual config. XGA Mode G ARC Reset 1024 x 768 1280 x 768 1360 x 768 1366 x 768 1. Press the MENU button and then use DD / EE button to select the SCREEN menu. 2. Press the GG button and then use DD / EE button to select XGA Mode. 3. Press the GG button and then use DD / EE button to select the desired XGA resolution. 4. Press the ENTER button to save. Picture Size (Aspect Ratio) Control Picture Size (Aspect Ratio) Control
- This feature allows an analog picture with a 4:3 aspect ratio is displayed on your TV. When you receive an
-
analog picture with a 4:3 aspect ratio on your 16:9 TV, you need to specify how the picture is to be displayed. If a fixed image is displayed on the screen for a long time, the image may become imprinted on the screen This phenomenon is common to all manufactures and in consequence the manufactures warranty does not cover the product bearing this phenomenon. 1. Press the ARC button repeatedly to select the desired picture format. You can also select picture format in the SCREEN menu. 4:3
- Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the left and right sides. 16:9
- Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen. Zoom 1
- Choose Zoom 1 when you want to view the picture without any alteration. However, the top and bottom por-
tions of the picture will be cropped. Zoom 1
- Choose Zoom 2 when you want the picture to be altered, both vertically extended and cropped. The picture taking a halfway trade off between alteration and screen coverage. 32 Plasma Monitor Initializing (Reset to original factory value) Initializing (Reset to original factory value)
- Use the Reset option to initialize the adjusted settings. Auto config. Manual config. XGA Mode ARC Reset Auto config. G Manual config. XGA Mode ARC Reset To set 1. Press the MENU button and then use DD / EE button to select the SCREEN menu. 2. Press the GG button and then use DD / EE button to select Reset. 3. Press the GG button. Operation Owners Manual 33 Operation External Control Device Setup External Control Device Setup
- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitors functions externally.
- Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.
- RS-232C connection cables are not supplied with the Monitor. REMOTE CONTROL IN RS-232C
(CONTROL&SERVICE) HDMI/DVI IN RGB AUD
(RGB OUT IN IN OUT TType of Connector: D-Sub 9-pin Male ype of Connector: D-Sub 9-pin Male No. Pin Name 1 2 3 4 5 6 7 8 9 No Connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection RS-232C Configurations RS-232C Configurations 1 5 9 6 7-Wire Configuration
(Standard RS-232C cable) 3- Wire Configuration
(Not standard) PC 2 3 5 4 6 7 8 RXD TXD GND DTR DSR RTS CTS PDP 3 2 5 6 4 8 7 TXD RXD GND DSR DTR CTS RTS PC 2 3 5 4 6 7 8 RXD TXD GND DTR DSR RTS CTS PDP 3 2 5 4 6 7 8 TXD RXD GND DTR DSR RTS CTS D-Sub 9 D-Sub 9 D-Sub 9 D-Sub 9 34 Plasma Monitor Set ID Set ID
- Use this function to specify a monitor ID number.
- Refer to Real Data Mapping 1. See page 38. Language Child lock ISM Method Set ID Tile mode Low power XD Demo External Control Device Setup Language Child lock ISM Method Set ID Tile mode Low power XD Demo G 1 1. Press the MENU button and then use the DD / EE button to select the SPECIAL menu. 2. Press the GG button and then use DD / EE button to select Set ID. 3. Press the GG button and then use F / G button to adjust Set ID to choose the desired monitor ID number. The adjustment range of Set ID is 1 ~ 99. COMMAND 1 COMMAND 2 DATA
(Hexadecimal) Communication Parameters Communication Parameters Baud rate : 9600 bps (UART) Data length : 8 bits Parity : None Command Reference List Command Reference List k 01. Power k 02. Input Select k 03. Aspect Ratio k 04. Screen Mute k 05. Volume Mute k 06. Volume Control k 07. Contrast k 08. Brightness k 09. Color k 10. Tint k 11. Sharpness 12. OSD Select k 13. Remote Control Lock Mode k 14. PIP/DW k k 15. PIP Position k 16. Treble k 17. Bass k 18. Balance 19. Color Temperature k k 20. Red adjustment k 21. Green adjustment k 22. Blue adjustment 23. PIP Input Select k k 24. Abnormal State j 25. ISM Method j 26. Low Power 27. Picture Size Setting j for DW mode 28. Auto Configure 29. Key j m a b c d e f g h i j k l m n q r s t u v w
$
y z p q t u c 0 ~ 1 1 ~ 9 0 ~ 3 0 ~ 1 0 ~ 1 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 1 0 ~ 1 0 ~ 3 0 ~ 3 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 3 0 ~ 14 0 ~ 14 0 ~ 14 1 ~ 9 0 ~ a 0 ~ 3 0 ~ 1 0 ~oa Stop bit : 1 bit Communication code : ASCII code TTransmission / Receiving Protocol ransmission / Receiving Protocol Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]: k, j, m
* [Command 2]: To control PDP set.
* [Set ID]: You can adjust the set ID to choose desired moni-
tor ID number in Special menu. Adjustment range is 1 ~ 99. When selecting Set ID 0, every con-
nected PDP set is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal
(0x0~0x63) on transmission/receiving protocol.
* [DATA]: To transmit command data. Transmit FF data to read status of command.
* [Cr]: Carriage Return ASCII code 0x0D
* [ ]: ASCII code space (0x20) OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer. Error Acknowledgement
[Command2][ ][Set ID][ ][NG][x]
* The Monitor transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors. 1 Key code Data 1: Illegal Code 2: Not supported function Owners Manual 35 External Control Device Setup 01. Power (Command 2:a) G To control Power On/Off of the Monitor. Transmission
[k][a][ ][Set ID][ ][Data][Cr]
1 : Power On Data 0 : Power Off Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
G To show Power On/Off. Transmission
[k][a][ ][Set ID][ ][FF][Cr]
Data 0 : Power Off Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
04. Screen Mute (Command 2:d) G To select screen mute on/off. Transmission
[k][d][ ][Set ID][ ][Data][Cr]
Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off) Acknowledgement
[d][ ][Set ID][ ][OK][Data][x]
Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off) 1 : Power On 05. Volume Mute (Command 2:e) G To control volume mute on/off. You can also adjust mute using the MUTE button on remote control.
* In a like manner, if other functions transmit FF data based on this format, Acknowledgement data feedback presents status about each function. Transmission
[k][e][ ][Set ID][ ][Data][Cr]
02. Input Select (Command 2:b) (Main Picture Input) G To select input source for the Monitor. You can also select an input source using the INPUT button on the Monitor's remote control. Transmission
[k][b][ ][Set ID][ ][Data][Cr]
Data 2 : AV 4 : Component1 5 : Component2 6 : RGB (DTV) Acknowledgement
[b][ ][Set ID][ ][OK][Data][x]
Data 2 : AV 4 : Component1 5 : Component2 6 : RGB (DTV) 7 : RGB (PC) 7 : RGB (PC) 8 : HDMI (DTV) 9 : HDMI (PC) 8 : HDMI (DTV) 9 : HDMI (PC) 03. Aspect Ratio (Command 2:c) (Main picture format) G To adjust the screen format. You can also adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in the Screen menu. Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 0 : Normal screen (4:3) 1 : Wide screen (16:9) 2 : Wide screen (Horizon) 3 : Full screen (Zoom) Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
36 Plasma Monitor Data 0 : Volume mute on (Volume off) 1 : Volume mute off (Volume on) Acknowledgement
[e][ ][Set ID][ ][OK][Data][x]
Data 0 : Volume mute on (Volume off) 1 : Volume mute off (Volume on) 06. Volume Control (Command 2:f) G To adjust volume. You can also adjust volume with the volume buttons on remote control. Transmission
[k][f][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64 Refer to Real data mapping 1. See page 38. Acknowledgement
[f][ ][Set ID][ ][OK][Data][x]
Data Min : 0 ~ Max : 64 07. Contrast (Command 2:g) G To adjust screen contrast. You can also adjust contrast in the picture menu. Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64 Refer to Real data mapping 1. See page 38. Acknowledgement
[g][ ][Set ID][ ][OK][Data][x]
Data Min : 0 ~ Max : 64 08. Brightness (Command2:h) G To adjust screen brightness. You can also adjust brightness in the Picture menu. Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64 Refer to Real data mapping 1. See page 38. Acknowledgement
[h][ ][Set ID][ ][OK][Data][x]
Data Min : 0 ~ Max : 64 09. Color (Command2:i) G To adjust the screen color. You can also adjust color in the Picture menu. Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64 Refer to Real data mapping 1. See page 38. Acknowledgement
[i][ ][Set ID][ ][OK][Data][x]
Data Min : 0 ~ Max : 64 10. Tint (Command2:j) G To adjust the screen tint. You can also adjust tint in the Picture menu. Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data Red : 0 ~ Green : 64 Refer to Real data mapping 1. See page 38. Acknowledgement
[j][ ][Set ID][ ][OK][Data][x]
Data Red : 0 ~ Green : 64 11. Sharpness (Command2:k) G To adjust the screen sharpness. You can also adjust sharpness in the Picture menu. Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64 Refer to Real data mapping 1. See page 38. Acknowledgement
[k][ ][Set ID][ ][OK][Data][x]
Data Min : 0 ~ Max : 64 External Control Device Setup 12. OSD Select (Command2:l) G To select OSD (On Screen Display) on/off. Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 0: OSD off 1: OSD on Acknowledgement
[l][ ][Set ID][ ][OK][Data][x]
Data 0: OSD off 1: OSD on 13. Remote Control Lock Mode (Command2:m) G To lock the remote control and front panel controls on the monitor Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data 0: lock off Acknowledgement
[m][ ][Set ID][ ][OK][Data][x]
1: lock on 1: lock on Data 0: lock off If youre not using the remote control and front panel con-
trols on the monitor, use this mode. When main power is on/off, remote control lock is released. 14. Balance (Command2:t) G To adjust balance. You can also adjust balance in the Sound menu. Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64 Refer to Real data mapping 1. See page 38. Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
Data Min: 0 ~ Max: 64 15. Color Temperature (Command2:u) G To adjust color temperature. You can also adjust ACC in the Picture menu. Transmission
[k][u][ ][Set ID][ ][Data][Cr]
Data 0: Normal 1: Cool 2: Warm 3: User Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
Data 0: Normal 1: Cool 2: Warm 3: User Owners Manual 37 External Control Device Setup 16. Abnormal State (Command2:z) 19. Key (Command2:c) G To recognize an abnormal state. Transmission
[k][z][ ][Set ID][ ][FF][Cr]
Data FF:Read Acknowledgement
[z][ ][Set ID][ ][OK][Data][x]
Data 0: Power on(signal) 1: Power on(No signal) 2: Remote control off 3: Sleep time off 4: RS-232C off 5: 5V monitor off 6: AC detect off 7: Fan Alarm off 8: Off timer off 9: No signal off a: Connection Detect off
* If you do not press any button within 2 hours after the monitor turns on with the On Timer function, the monitor will automatically revert to standby mode. 17. ISM Method (Command2:p) G To avoid having a fixed image remain on screen. Transmission
[j][p][ ][Set ID][ ][Data][Cr]
Data 1: Inversion 4: White Wash 8: Normal 2: Orbiter 3: Orb.+Inv. Acknowledgement
[p][ ][Set ID][ ][OK][Data][x]
Data 1: Inversion 2: Orbiter 3: Orb.+Inv. G To adjust Key code for IR remote control. Transmission
[m][c][ ][Set ID][ ][Data][Cr]
Data Key code : Refer to See page 41. Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
20. Tile Mode (Command : d d) G Change a Tile Mode. Transmission
[d][d][ ][Set ID][ ][Data][Cr]
Data 0: Tile mode is off. 12: 1 x 2 mode (column x row) 13: 1 x 3 mode 14: 1 x 4 mode 44: 4 x 4 mode Acknowledgement
[d][ ][Set ID][ ][OK][Data][x]
Data 0: Tile mode is off. 12: 1 x 2 mode (column x row) 13: 1 x 3 mode 14: 1 x 4 mode 4: White Wash 8: Normal 44: 4 x 4 mode 18. Auto Configure (Command2:u) G To adjust picture position and minimize image shaking automatically. Auto Configure only works in RGB-PC mode. Transmission
[j][u][ ][Set ID][ ][Data][Cr]
Data 1 Refer to Real data mapping1. See page 38. Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
Data 1 38 Plasma Monitor
* Real data mapping 1 0 : Step 0 A : Step 10 (SET ID 10) F : Step 15 (SET ID 15) 10 : Step 16 (SET ID 16) 63 : Step 99 (SET ID 99) 64 : Step 100
* Real data mapping 2 0 : -10 1 : - 9 2 : - 8 A : 0 12 : + 8 13 : + 9 14 : + 10 21. Tile H Size (Command : d g) G To set the Horizontal size. Transmission
[d][g][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64 Acknowledgement
[g][ ][Set ID][ ][OK][Data][x]
Data Min: 0 ~ Max: 64 22. Tile V Size (Command : d h) G To set the Vertical size. Transmission
[d][h][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64 Acknowledgement
[h][ ][Set ID][ ][OK][Data][x]
Data Min: 0 ~ Max: 64 23. Tile ID Set (Command : d i) G To assign the Tile ID for Tiling function. Transmission
[d][i][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64 Acknowledgement
[i][ ][Set ID][ ][OK][Data][x]
Data Min: 0 ~ Max: 64 24. Elapsed time return (Command : d l) G To read the elapsed time. Transmission
[d][l][ ][Set ID][ ][Data][Cr]
* The data is always FF(in Hex). Acknowledgement
[l][ ][Set ID][ ][OK][Data][x]
* The data means used hours. (Hexadecimal code) External Control Device Setup 26. Low Power (Command2:q) G To control the low power function on/off. Transmission
[j][q][ ][Set ID][ ][Data][Cr]
Data 0: Low power off 1: Low power on Acknowledgement
[q][ ][Set ID][ ][OK][Data][x]
Data 0: Low power off 1: Low power on Owners Manual 39 External Control Device Setup IR Code IR Code How to Connect How to Connect G Connect your wired remote control to the Remote Control port on the Monitor. Remote Control IR Code Remote Control IR Code G Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz TC T1 Carrier frequency FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3 G Configuration of frame 1st frame Lead code Low custom code High custom code Data code Data code C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 Repeat frame G Lead code Repeat code Tf 9 ms 4.5 ms G Repeat code 0.55 ms G Bit description Bit 0 9 ms 0.56 ms 1.12 ms 2.25 ms Bit 1 G Frame interval : Tf The waveform is transmitted as long as a key is depressed. Tf Tf 40 Plasma Monitor Tf=108ms @455KHz 0.56 ms 2.24 ms Code (Hexa) Function Note 10 11 12 13 14 15 16 17 18 19 0E 09 08 02 03 00 01 4D 52 44 0B 43 79 62 64 07 06 40 41 5B 60 92 61 6B CD CE 3E 75 99 5A D0 BF D4 D5 C6 Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6 Number Key 7 Number Key 8 Number Key 9 SLEEP MUTE POWER VOL+
VOL-
CH+
CH-
APC DASP ENTER () AII INPUT SELECT MENU ARC Window Position Window Size F G D E EXIT PIP XD PIP Input DW Video HDMI2 Key lock Index Auto config. Input video1 Input video2 Input Component 1 Input Component 2 Input RGB Input HDMI1/DVI R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button (Power On/Off) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button (4:3/16:9/Horizon/Zoom mode Selection) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button Discrete IR Code (Only RGB mode) Discrete IR Code (Input Video 1 Selection) Discrete IR Code (Input Video 2 Selection) Discrete IR Code (Input Component 1 Selection) Discrete IR Code (Input Component 2 Selection) Discrete IR Code (Input RGB Selection) Discrete IR Code (Input HDMI1/DVI Selection) IR Code Owners Manual 41 Programming the Remote TTroubleshooting Checklist roubleshooting Checklist The operation does not work normally. Check to see if there is any object between the product and the remote The remote control doesnt work control causing obstruction. Are batteries installed with correct polarity (+ to +, - to -)?
Correct remote operating mode set: TV, VCR etc.?
Install new batteries. Power is suddenly turned off Is the sleep timer set?
Check the power control settings. Power interrupted No broadcast on station tuned with Auto off activated. The video function does not work. No picture &
No sound Check whether the product is turned on. Try another channel. The problem may be with the broadcast. Is the power cord inserted into wall power outlet?
Check your antenna direction and/or location. Test the wall power outlet, plug another products power cord into the outlet where the products power cord was plugged in. Picture appears slowly after switching on This is normal, the image is muted during the product startup process. Please contact your service center, if the picture has not appeared after five minutes. No or poor color or poor picture Adjust Color in menu option. Keep a sufficient distance between the product and the VCR. Try another channel. The problem may be with the broadcast. Are the video cables installed properly?
Activate any function to restore the brightness of the picture. Horizontal/verti-
cal bars or pic-
ture shaking Check for local interference such as an electrical appliance or power tool. Poor reception on some channels Station or cable product experiencing problems, tune to another station. Station signal is weak, reorient antenna to receive weaker station. Check for sources of possible interference. Lines or streaks in pictures Check antenna (Change the direction of the antenna). 42 Plasma Monitor Programming the Remote The audio function does not work. Picture OK &
No sound Press the VOL or VOLUME button. Sound muted? Press MUTE button. Try another channel. The problem may be with the broadcast. Are the audio cables installed properly?
No output from one of the speakers Adjust Balance in menu option. Unusual sound from inside the product A change in ambient humidity or temperature may result in an unusual noise when the product is turned on or off and does not indicate a fault with the product. There is a problem in PC mode.
(Only PC mode applied) Adjust resolution, horizontal frequency, or vertical frequency. Check the input source. Work the Auto configure or adjust clock, phase, or H/V position. (Option) Check the signal cable. Reinstall the PC video card. The signal is out of range. Vertical bar or stripe on back-
ground &
Horizontal Noise &
Incorrect position Screen color is unstable or single color Owners Manual 43 Troubleshooting Checklist Maintenance Maintenance
- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen Cleaning the Screen 1. Heres a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until its almost dry, and then use it to wipe the screen. 2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV. Cleaning the Cabinet Cleaning the Cabinet To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please do not use a wet cloth. Extended Absence Absence Extended If you expect to leave your TV dormant for a long time (such as a vacation), its a good idea to unplug the power cord to protect against possible damage from lightning or power surges. 44 Plasma Monitor Specifications Product Specifications Product Specifications MODELS Width (inches / mm) Height (inches / mm) Depth (inches / mm) Weight (pounds / kg) Power requirement Resolution Environmental condition Operating Temperature Operating Humidity Storage Temperature Storage Humidity 42PM4M
(42PM4M-WA) 42.0 / 1066.0 25.6 / 650.0 3.8 / 97.5 66.1 / 30.0 AC100-240V ~ 50/60Hz 1920 x 1080 (Dot) 32 ~ 104F (0 ~ 40C) Less than 80%
-4 ~ 140F (-20 ~ 60C) Less than 85%
The specifications shown above may change without notice for quality improvement. Owners Manual 45
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2007-08-27 | JBP - Part 15 Class B Computing Device Peripheral | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2007-08-27
|
||||
1 | Applicant's complete, legal business name |
LG Electronics USA
|
||||
1 | FCC Registration Number (FRN) |
0020917688
|
||||
1 | Physical Address |
1000 Sylvan Avenue
|
||||
1 |
Englewood Cliffs, NJ
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
m******@ccsemc.com
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
BEJ
|
||||
1 | Equipment Product Code |
42PM4MWA
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
K**** H******
|
||||
1 | Title |
Director, Standards & Compliance
|
||||
1 | Telephone Number |
201-4********
|
||||
1 | Fax Number |
201-8********
|
||||
1 |
k******@lge.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | JBP - Part 15 Class B Computing Device Peripheral | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | PLASMA MONITOR | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
ESTECH Co., Ltd.
|
||||
1 | Name |
Y**** J******
|
||||
1 | Telephone Number |
82-31********
|
||||
1 | Fax Number |
82-31********
|
||||
1 |
j******@estech.co.kr
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15B | 16 21 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC