User Manual PRODUCT NAME : RF Module MODEL NAME : LGSBWAC61 The information contained herein is the exclusive property of LG Innotek and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG Innotek.
(00)-0073 REG. DATE : 2015.08.10 REV. DATE : 2015.08.10 User Manual MODEL NAME: TWCM-B301D(LGIT) LGSBWAC61(LGE) REV.NO : v0.01 PAGE :
1 / 9 DOCUMENT No :
-
Index Features Picture of Product Installation Manual Block Diagram Absolute Maximum Ratings No Description 1 2 3 4 5 6 Operating Conditions 7 8 9 Out Drawing 10 Packing Information Standard Test Conditions Pin Description Page 2 2 3 4 4 5 5 6 7 8 Copyright. 2015. All Rights Reserved. REG. DATE : 2015.08.10 REV. DATE : 2015.08.10 User Manual MODEL NAME: TWCM-B301D(LGIT) LGSBWAC61(LGE) REV.NO : v0.01 PAGE :
2 / 9 DOCUMENT No :
-
1. Features TWCM-B301D is the small size and low power module for IEEE 802.11ac wireless LAN
& BT4.1 + HS. TWCM-B301D is based on Broadcom BCM43569 solution. IEEE 802.11 a/b/g/n/ac Dual Band WLAN infrastructure Bluetooth 4.1 + HS Size : 68.0mm x 38.0mm Two stream spatial multiplexing up to 300Mbps(802.11n)/ 867Mbps(802.11ac) WLAN Metal Press antenna, BT Printed antenna on Use on-chip OTP (One-Time Programmable) Host Interface : USB2.0 (WLAN & BT)
- This model is using the common USB2.0 to control WLAN and BT Security : WAPI, WEP, WPA, WPA2, WMM, AES, WEP, TKIP, CKP Application: DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB 2. Picture of Product Copyright. 2015. All Rights Reserved. REG. DATE : 2015.08.10 REV. DATE : 2015.08.10 User Manual MODEL NAME: TWCM-B301D(LGIT) LGSBWAC61(LGE) REV.NO : v0.01 PAGE :
3 / 9 DOCUMENT No :
-
3. Installation Manual Install the module like below in the back of the TV TWCM-B301D installed position Copyright. 2015. All Rights Reserved. REG. DATE : 2015.08.10 REV. DATE : 2015.08.10 User Manual MODEL NAME: TWCM-B301D(LGIT) LGSBWAC61(LGE) REV.NO : v0.01 PAGE :
4 / 9 DOCUMENT No :
-
5. Absolute Maximum Ratings Caution : The specifications in Table 1 define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device. Parameter Storage Temperature Storage Humidity (40) Min
-20
-
Max
+80 90 Unit
%
. Other conditions 1) Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperature and relative humidity do not exceed 5 to 40 and 20 to 60%. 3) Assemble the modules within 6 months. Check the soldering ability in case of 6 months over. Copyright. 2015. All Rights Reserved. REG. DATE : 2015.08.10 REV. DATE : 2015.08.10 User Manual MODEL NAME: TWCM-B301D(LGIT) LGSBWAC61(LGE) REV.NO : v0.01 PAGE :
5 / 9 DOCUMENT No :
-
6. Operating Conditions Parameter Ambient Temperature Ambient Humidity (40) Supply Voltage Min 0
-
4.75 Typ
-
-
5.0 Max 60 85 5.25 Unit
%
Vdc 7. Standard Test Conditions The Test for electrical specification shall be performed under the following condition Otherwise this following conditions, not guaranteed this performance. 7-1. Ambient condition Temparature Humidity 7-2. Power supply voltages Input Voltage VDD_3.3V 25 5 65 5%
Supply Voltage
+3.3V 0.165V Copyright. 2015. All Rights Reserved. REG. DATE : 2015.08.10 REV. DATE : 2015.08.10 User Manual MODEL NAME: TWCM-B301D(LGIT) LGSBWAC61(LGE) REV.NO : v0.01 PAGE :
6 / 9 DOCUMENT No :
-
8. Pin Description Pin No. Pin Name I/O Pin Description 1 2 3 4 5 6 7 8 GND BT_REG_ON 3D_Sync WL_HOST_WAKE GND USB D+
USB D-
VCC
-
-
-
-
-
I/O I/O I Ground BT Regulator ON 3D_Sync Wake On WLAN Ground USB Communication signal USB D+
USB Communication signal USB D-
VDD 3.3V Copyright. 2015. All Rights Reserved. REG. DATE : 2015.08.10 REV. DATE : 2015.08.10 User Manual MODEL NAME: TWCM-B301D(LGIT) LGSBWAC61(LGE) REV.NO : v0.01 PAGE :
7 / 9 DOCUMENT No :
-
9. Outline Drawing Copyright. 2015. All Rights Reserved. DOCUMENT No :
-
REG. DATE : 2015.08.10 REV. DATE : 2015.08.10 User Manual MODEL NAME: TWCM-B301D(LGIT) LGSBWAC61(LGE) REV.NO : v0.01 PAGE :
8 / 9 10. Packing Information Copyright. 2015. All Rights Reserved. REG. DATE : 2015.08.10 REV. DATE : 2015.08.10 User Manual MODEL NAME: TWCM-B301D(LGIT) LGSBWAC61(LGE) REV.NO : v0.01 PAGE :
9 / 9 DOCUMENT No :
-
TWCM-B301D Copyright. 2015. All Rights Reserved. Regulatory Notices 1. FCC FCC Part 15.19 Statements:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part 15.21 statement Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FCC Part 15.105 statement (Class A or Class B ) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. OEM Responsibilities to comply with FCC and Industry Canada Regulations The module has been certified for integration into products only by OEM integrators under the following condition:
- The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.
- The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. As long as the two condition above is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). End Product Labeling (Module ) The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:
Contains FCC ID: BEJLGSBWAC61 Contains IC: 2703H-LGSBWAC61 2. IC RSS-GEN, Sec. 7.1.2 (transmitters) ( ) Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation dIndustrie Canada, le prsent metteur radio peut fonctionner avec une antenne dun type et dun gain maximal (ou infrieur) approuv pour lmetteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique lintention des autres utilisateurs, il faut choisir le type dantenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpassepas lintensit ncessaire ltablissement dune communication satisfaisante. RSS-GEN, Sec. 7.1.2 (detachable antennas) ( ) This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (identifier le dispositif par son numro de certification ou son numro de modle sil fait partie du matriel de catgorie I) a t approuv par Industrie Canada pour fonctionner avec les types dantenne numrs ci-dessous et ayant un gain admissible maximal et limpdance requise pour chaque type dantenne. Les types dantenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour lexploitation de lmetteur. RSS-GEN, Sec. 7.1.3 (licence-exempt radio apparatus) (BT or WLAN , ) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. RF Exposure The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20 cm between the radiation source (antenna) and any individual. This device may not be installed or used in conjunction with any other antenna or transmitter. l'exposition aux RF Lantenne (ou les antennes) doit tre installe de faon maintenir tout instant une distance minimum de au moins 20 cm entre la source de radiation (lantenne) et toute personne physique. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate thisequipment.Attention:
Les changements ou modifications de cet appareil non expressment approuv par le fabricant peuvent annuler votre droit utiliser cet quipement. tiquetage du produit final (IC) (Module ) Le module BT111 est tiquet avec sa propre identification FCC et son propre numro de certification IC. Si lidentification FCC et le numro de certification IC ne sont pas visibles lorsque le module est install lintrieur dun autre dispositif, la partie externe du dispositif dans lequel le module est install devra galement prsenter une tiquette faisant rfrence au module inclus. Dans ce cas, le produit final devra tre tiquet sur une zone visible avec les informations suivantes :
Contient module metteur identification FCC ID : BEJLGSBWAC61 Contient module metteur IC : 2703H-LGSBWAC61 Regulatory Notices 1. FCC FCC Part 15.19 Statements:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part 15.21 statement Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FCC Part 15.105 statement (Class A or Class B ) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. OEM Responsibilities to comply with FCC and Industry Canada Regulations The module has been certified for integration into products only by OEM integrators under the following condition:
- The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.
- The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. As long as the two condition above is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). End Product Labeling (Module ) The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:
Contains FCC ID: BEJLGSBWAC61 Contains IC: 2703H-LGSBWAC61 2. IC RSS-GEN, Sec. 7.1.3 (licence-exempt radio apparatus) (BT or WLAN , ) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. RF Exposure The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20 cm between the radiation source (antenna) and any individual. This device may not be installed or used in conjunction with any other antenna or transmitter. l'exposition aux RF Lantenne (ou les antennes) doit tre installe de faon maintenir tout instant une distance minimum de au moins 20 cm entre la source de radiation (lantenne) et toute personne physique. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate thisequipment.Attention:
Les changements ou modifications de cet appareil non expressment approuv par le fabricant peuvent annuler votre droit utiliser cet quipement. tiquetage du produit final (IC) (Module ) Le module BT111 est tiquet avec sa propre identification FCC et son propre numro de certification IC. Si lidentification FCC et le numro de certification IC ne sont pas visibles lorsque le module est install lintrieur dun autre dispositif, la partie externe du dispositif dans lequel le module est install devra galement prsenter une tiquette faisant rfrence au module inclus. Dans ce cas, le produit final devra tre tiquet sur une zone visible avec les informations suivantes :
Contient module metteur identification FCC ID : BEJLGSBWAC61 Contient module metteur IC : 2703H-LGSBWAC61