Date : Jan. 10, 2014 Rev : 2.1 Modular Approval Declaration Letter HACS-F007 Modular Approval Declaration Letter HCT America LLC
(TCB@hctamerica.com) 44364 S. Grimmer Blvd. Fremont, CA 94538 TEL: +1.510.933.8848, Fax: +1.510.933.8849 Page 1 of 2 This document is electronically controlled. Hard copy documents are uncontrolled. Please check all hard copies against the controlled electronic copy to ensure validity. This document is the confidential property of HCT America LLC. It may not be forwarded or reproduced in whole or in part without written permissions from HCT America LLC Date : Jan. 10, 2014 Rev : 2.1 REVISION TABLE Rev 1.0 2.0 2.1 Description of Change Original Release(Obsolete) Updated Template(Obsolete) Updated address Date 06/14/2012 10/01/2012 01/10/2014 Approved QM QM QM HACS-F007 Modular Approval Declaration Letter HCT America LLC
(TCB@hctamerica.com) 44364 S. Grimmer Blvd. Fremont, CA 94538 TEL: +1.510.933.8848, Fax: +1.510.933.8849 Page 2 of 2 This document is electronically controlled. Hard copy documents are uncontrolled. Please check all hard copies against the controlled electronic copy to ensure validity. This document is the confidential property of HCT America LLC. It may not be forwarded or reproduced in whole or in part without written permissions from HCT America LLC Date: June 13, 2016 Subject : Modular Approval Declaration Letter FCC ID : BEJ-LCW004 is seeking FCC equipment authorization as Single Modular Transmitter Single Limited Modular Transmitter Equipment Under Testing (EUT) satisfy the requirement for Single Modular Approval Single Limited Modular Approval as detailed in FCC Public Notice DA00-1407. FCC Requirement of Modular Approval 1. The modular transmitter must have its own RF shielding. 2. The modular transmitter must have buffered modulation/data inputs. 3. The modular transmitter must have its own power supply regulation. 4. The modular transmitter must comply with the antenna requirements of section 5. The modular transmitter must be tested in a stand-alone configuration. 6. The modular transmitter must be labeled with its own FCC ID number. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacture must provide adequate instruction along with the module to explain any such requirements. 15.203 and 15.204(c). 7. YES YES YES YES YES YES YES NO NO NO NO NO NO NO YES NO requirements. 8. The modular transmitter must comply with any applicable RF exposure Note :
Limited modular approval may be granted If EUT does not meet all of the requirement shown above Limited modular approval may be granted in case that the applicant can demonstrate to retain control over the final installation of the device such that compliance of the end product is assured. In that case, an operating condition on the limited modular approval for the module shall state that the module is only designated for the end product manufactured by a specific manufacturer When limited modular approval is sought, the application for equipment certification shall state how control of the end product into which the module will be installed and maintained such that full compliance of the end product is always ensured. It shall be provided that clear and specific instructions describing the conditions limitations and procedures for third-parties to use and/or integrate the module into a host device For non-Software Defined Radio transmitter modules where software is used to ensure compliance of the device, it shall be provided that the technical description of how such control is implemented to ensure to prevent the third party from modifying
(see KDB 594280). Compliance of a module in its final configuration is the responsibility of the applicant. A host device will not be considered certified if the instructions regarding antenna configuration provided in the original description, of one or more separately certified modules it contains, were not followed. Example: A separately certified low-power transceiver module using Bluetooth technology which is housed in a desktop computer, laptop or peripheral does not require the overall system to be recertified, if the desktop computer, laptop or peripheral, as a stand-alone unit, complies with all applicable technical standards. Signed by:
Jongchul LEE / Director, Standards & Compliance Company Name : LG Electronics USA. Company Address : 1000 Sylvan Avenue, Englewood Cliffs, New Jersey, United States HACS-F007 Modular Approval Declaration Letter Rev : 2.1