User manual
< WM6687>
Dual-Band 802.11ac 4x4 MIMO PCI Express Mini Card Wireless Network Adapter LITE-ON Version: 1.0.0 This document contains confidential proprietary information and is property of LTC. The contents of this document should not be disclosed to unauthorized persons without the written consent of LTC. Content Product Specification of WM882 1 Product Description
. 2 Application 3 Features
. 4 Product Specifications . 5 Pin Definition
..... Page 4 4 4 5 5 6 Physical & Environment 6.1 PCB Dimension 6 6.2 Operation Temperature & Humidity .... 6 6.3 Storage Temperature & Humidity
... 6 7 Certification Requirements ..... 6 Rev.:1.0.0 2 / 14 Product Specification of WM882 Change History Version Revised Date 1.0.0 2016/12/15 Editor Flora Yu Content Revised First Edition (baseline) Rev.:1.0.0 3 / 14 Product Specification of WM882 1 Product Descriptions The WM6687 provides ultra-high performance transmission rate in the 2.4G or 5GHz band. It is backward compatible with the current 802.11a/b/g/n network devices. 2 Application Home and/or office wireless networking Wireless multimedia Wireless extension of existing wired network 3 Features IEEE 802.11 a/b/g/n/ac standard compliant 4x4 MIMO wireless system Ultra-high data rate up to 1.7Gbps @5GHz, 256QAM Auto fallback data rate under noisy environment Support 2.4GHz or 5GHz band operation (dual-band selectable) Support WEP ( 64-bit/128-bit ), 802.1x, and WPA/WPA2 Conformable to industry-standard Mini Card specification Independent Tx Power Control on a per channel 4 Product Specifications Radio Chipset WLAN Standards Antenna connector Data Rate (per stream) BCM43465 IEEE 802.11a/b/g/n/ac compliant U.FL connector 802.11a: 6, 9, 12, 18, 24, 36, 48, 54 Mbps 802.11b: 11, 5.5, 2 & 1 Mbps 802.11g: 54, 48, 36, 24, 18, 12, 9 & 6 Mbps 802.11n :
20 MHz BW: 72.2, 65, 57.8, 43.3, 28.9, 21.7, 14.4, 7.2 Mbps 40 MHz BW: 150, 135, 120, 90, 60, 45, 30, 15 Mbps 802.11ac :
20MHz BW : 86.7, 72.2, 65, 57.8, 43.3, 28.9, 21.7, 14.4, 7.2 Mbps 40MHz BW : 200, 180, 150, 135, 120, 90, 60, 45, 30, 15 Mbps 80MHz BW : 433, 390, 325, 292.5, 260, 195, 130, 97.5, 65, 32.5 Mbps 160MHz BW: 867, 780, 650, 585, 520, 390, 260, 195, 130, 65 Mbps Rev.:1.0.0 4 / 14 Product Specification of WM882 802.11b: CCK(11&5.5 Mbps), DQPSK (2Mbps), DBPSK (1Mbps), 802.11g/n: DBPSK, DQPSK, OFDM, BPSK, QPSK, 16QAM, 64QAM, 256QAM, 1024QAM (proprietary) USA FCC 2412~2462MHz Canada IC 2412~2462MHz Europe ETSI 2412~2472MHz Japan STD-T66/STD-33m 2412~2484MHz 5150MHz ~ 5350MHz for US & Canada 5150MHz ~ 5350MHz for Europe 5470MHz ~ 5725MHz for Europe 5030MHz~5091MHz and 5150MHz ~ 5250MHz for Japan 5150MHz ~ 5350MHz for Australia 5470MHz ~ 5725MHz for Australia (except channel 120, 124 and 128) 5725Mhz ~ 5825Mhz for Australia 2.4GHz or 5GHz Operation (max.) < 5.6W (estimated) WEP (64-bit/128-bit), 802.1x WPA/WPAs (TKIP, AES) Linux Data Rates 6 Mbps 54 Mbps 802.11n - 20 MHz 802.11n - 40 MHz VHT20 MCS 8 -63 VHT40 MCS 9 -60 VHT80 MCS 9 -57 3.3 VDC from host (+/- 0.2V) Receive Sensitivity (min.)
-90 dBm
-71dBm
-89 (MSC 0/8)
-86 (MSC 0/8) Modulation Operating Frequencies Frequency Band Power Consumption Security Operating System Receive Sensitivity Voltage 5 Pin Definition PCIE pin number Pin definition PCIE pin number Pin definition 1 2 3 4 5 6 7 8 9 10 11 12 13 PCIE_WAKE_L VDD3_3 NC GND NC NC PCIE_CLKREQ_L NC GND NC REFCLKN NC REFCLKP 27 28 29 30 31 32 33 34 35 36 37 38 39 GND NC GND NC PCIE_RDP NC PCIE_RDN GND GND NC GND NC VDD3_3 Rev.:1.0.0 5 / 14 Product Specification of WM882 14 15 16 17 18 19 20 21 22 23 24 25 26 NC GND NC NC GND NC RF_DISABLE_L GND PCIE_PERST_L TDP VDD3_3 TDN GND 40 41 42 43 44 45 46 47 48 49 50 51 52 GND VDD3_3 NC GND LED_WLAN NC NC NC NC NC GND NC VDD3_3 6 Physical & Environment 6.1 PCB Dimension:
Standard mPCIe form factor: 30 50.95 mm (width length)
-
6.2 Operation Temperature & Humidity 45 Temperature32 to 1 13 (0 Humidity10% ~ 90% R.H. to
-
-
) 6.3 Storage Temperature& Humidity
-
-
Temperature-4 to 158 ( -20 Humidity10% ~ 95% R.H. 7 Certification Requirements to 70
)
- USA (Non DFS) Rev.:1.0.0 6 / 14 Product Specification of WM882
- USA (DFS)
- Canada (IC)
-
Japan (TELEC) Note, cert for module slave mode only, system products with/after the module installed/embedded need to re-cert and under customers expense. Rev.:1.0.0 7 / 14 Product Specification of WM882 FCC Statement:
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 25 cm between the radiator & your body. Rev.:1.0.0 8 / 14 Product Specification of WM882 IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 25 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the labelling area is small than the palm of the hand, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: PPQ-WM6687 ". If the labelling area is larger than the palm of the hand, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Rev.:1.0.0 9 / 14 Product Specification of WM882 Antenna list:
Brand Set Model Name
(P/N) 1 2 PSA RFDPA171300SBLB802 ethertronics M830520 Dipole Antenna Ceramic Antenna Antenna Type Connector Gain
(dBi) Reversed-SMA Note 1 N/A Note 1 Note 1:
Set 1 2 Gain (dBi) Cable loss True Gain (dBi) 2.4GHz 4.03 5GHz 5.4 1.1 3.2 2.4GHz 0.5 1.2 0.5 5GHz 0.5 2.2 0.9 2.4GHz 3.53
-0.1 0.6 5GHz 4.9 1 2.3 Remark
-
Connect with Black Cable or Grey Cable Remark
-
Black Cable
(Long) Gray Cable
(Short) Note 2:
The EUT has two sets of antennas and there are four antennas for each set. The Set 2 antennas can connect with black and gray cable. After evaluating, gray cable was select as the representative cable for the test and its data was recorded in this report. IC Statement:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux tats-Unis / Canada du march, seul le canal 1 11 peuvent tre exploits. Slection d'autres canaux n'est pas possible. Rev.:1.0.0 10 / 14 Product Specification of WM882 This radio transmitter (IC: 4491A-WM6687) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (IC: 4491A-WM6687) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Antenna list:
Brand Set Antenna Type Connector Model Name
(P/N) 1 2 PSA RFDPA171300SBLB802 ethertronics M830520 Gain
(dBi) Reversed-SMA Note 1 N/A Note 1 Dipole Antenna Ceramic Antenna Note 1:
Set 1 2 Gain (dBi) Cable loss True Gain (dBi) 2.4GHz 4.03 5GHz 5.4 1.1 3.2 2.4GHz 0.5 1.2 0.5 5GHz 0.5 2.2 0.9 2.4GHz 3.53
-0.1 0.6 5GHz 4.9 1 2.3 Remark
-
Connect with Black Cable or Grey Cable Remark
-
Black Cable
(Long) Gray Cable
(Short) Note 2:
The EUT has two sets of antennas and there are four antennas for each set. The Set 2 antennas can connect with black and gray cable. After evaluating, gray cable was select as the representative cable for the test and its data was recorded in this report. Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 5650-5725 MHz. Slection dynamique de frquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-5600 MHz et 5650-5725 MHz. Rev.:1.0.0 11 / 14 Product Specification of WM882 The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit. le gain maximal dantenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer la limite de p.i.r.e. The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate. le gain maximal dantenne permis (pour les dispositifs utilisant la bande 5725-5850 MHz) doit se conformer la limite de p.i.r.e. spcifie pour lexploitation point point et non point point, selon le cas. For indoor use only. Pour une utilisation en intrieur uniquement. IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 25 cm between the radiator & your body. Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 25 cm de distance entre la source de rayonnement et votre corps. Rev.:1.0.0 12 / 14 Product Specification of WM882 IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. 25 cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the IC RSS-102 radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 25 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains IC: 4491A-WM6687 ". The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online. Rev.:1.0.0 13 / 14 Product Specification of WM882 Japan Statement:
5GHz band (W52, W53): Indoor use only Rev.:1.0.0 14 / 14