submitted | available | document details (if available) | source link |
---|---|---|---|
November 10 2019 | LiteOn Technology Corp. Tracy Chang Adobe PDF Library 15.0 |
various | User Manual | Users Manual | 731.06 KiB | November 10 2019 |
USER MANUAL 802.11a/b/g/n/ac 2Tx2R+BT5.0 USB WLAN Module WCBN3509R, WCBN3509R(AU) Page 1/15 PRODUCT FEATURES BT FEATURE:
Bluetooth V5.0 system Backwards compatible with BT version of 1.1, 1.2, 2.0, 2.1, 3.0+HS and 4.0LE Bluetooth Class I transmission power Support for Simple Pairing (SP) and Enhanced Inquiry Response (EIR) function Support for SCATTERNET and up to 7 piconets simultaneously with background inquiry/page scan Up to 7 BT link + 32BLE link Support wide-band speech and hardware accelerated SBC codec for A2DP streaming Packet loss concealment Channel quality driven data rate adaptation Support Wake On Bluetooth WI-FI FEATURE:
Operate at ISM frequency Band (2.4/5GHz) IEEE Standards Support, 802.11a ,802.11b, 802.11g, 802.11n and 802.11ac Support for both 20 MHz, 40MHz and 80 MHz channel width in 2.4GHz and 5GHz band Enterprise level security supporting: WPS2.0,WAPI, WPA, WPA2 Support 2 transmission and 2 receiving, transmission rate can up to 300Mbps
(Physical Rate) in downstream and upstream Dual-stream IEEE 802.11ac support for 80MHz channels provides PHY layer rates up to 867Mbps QoS support of WFA WMM, WMMPS Support MU-MIMO RX Support STBC, LDPC, TX&RX beamforming Support Wake On WLAN COMMON FEATURE:
MT7668BU is a single chip integrated IEEE 802.11 a/b/g/n/ac and Bluetooth 5.0 with a single USB interface PA, LNA, and T/R switch integration for Wi-Fi and Bluetooth Advanced FDD/TDD mode Wi-Fi/Bluetooth coexistence scheme Fully compliance with USB v2.0 specification RoHS compliance Low Halogen compliance Page 2/15 PRODUCT SPECIFICATIONS MAIN CHIPSET MediaTek MT7668BU FUNCTIONAL SPECIFICATIONS BT Function Standard Bus Interface Data Rate Bluetooth V5.0LE USB2.0 1 Mbps, 2Mbps and Up to 3Mbps Modulation Scheme GFSK, /4-DQPSK and 8-DPSK Frequency Range 2.402~2.480 GHz Transmit Output Power
+4 Output Power +10dBm; Class I Device Receiver Sensitivity Wi-Fi Function Standard Bus Interface Data Rate Media Access Control Modulation Technique
< 0.1% BER at -88dBm IEEE802.11a; IEEE802.11b; IEEE 802.11g; IEEE 802.11n. IEEE802.11ac USB2.0 802.11a:
54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11b:
802.11g:
802.11n:
802.11ac:
11, 5.5, 2, 1 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps MCS 0 to 15 for HT20MHz MCS 0 to 15 for HT40MHz MCS 0 to 8 for HT20MHz MCS 0 to 9 for HT40MHz MCS 0 to 9 for HT80MHz CSMA/CA with ACK 802.11a:
64QAM, 16QAM, QPSK, BPSK CCK, DQPSK, DBPSK 64QAM, 16QAM, QPSK, BPSK 64QAM, 16QAM, QPSK, BPSK 802.11b:
802.11g:
802.11n:
802.11ac:
256QAM, 64QAM, 16QAM, QPSK, BPSK Page 3/15 Network Architecture Operation Channel Frequency Range EVM Ad-hoc mode (Peer-to-Peer) Infrastructure mode 2.4GHz 11: (Ch. 1-11) United States 13: (Ch. 1-13) Europe 14: (Ch. 1-14) Japan 5GHz 21: USA 19: EU 8: Japan 802.11bg 2.400 ~ 2.4835 GHz 802.11a 5.15 ~ 5.85 GHz CCK < 35%
OFDM < -25dB MCS0(HT20/40MHz) < -5dB MCS7(HT20/40MHz) < -28dB MCS0(VHT20/40/80MHz) < -5dB MCS7(VHT 20/40/80MHz) < -27dB MCS8(VHT 20/40/80MHz) < -30dB MCS9(VHT 20/40/80MHz) < -32dB 2.4&5GHz
-20ppm < Center Frequency < +20ppm Frequency Offset Transmit Output Power - single chain @ant;
Tolerance: 1.5dBm@2.4GHz; 2dBm@5GHz 2.4GHz 802.11b Tgtpwr
(dBm) 2Mbps 16 1Mbps 16 6~24Mbps 15 36Mbps 15 MCS0 15 MCS5 15 MCS0 15 MCS5 15 MCS1 15 MCS6 15 MCS1 15 MCS6 15 MCS2 15 MCS7 15 MCS2 15 MCS7 15 5.5Mbps 16 48Mbps 15 11Mbps 16 54Mbps 15 MCS3 15 MCS8 MCS3 15 MCS8 MCS4 15 MCS9 MCS4 15 MCS9 6~24Mbps 14 36Mbps 14 48Mbps 14 54Mbps 14 Page 4/15 802.11g Tgtpwr
(dBm) 802.11n HT20 Tgtpwr
(dBm) 802.11n HT40 Tgtpwr
(dBm) 5GHz 802.11a Tgtpwr
(dBm) 802.11n HT20 Tgtpwr
(dBm) 802.11n HT40 Tgtpwr
(dBm) 802.11ac VHT20 Tgtpwr
(dBm) 802.11ac VHT40 Tgtpwr
(dBm) MCS0 14 MCS5 14 MCS0 13 MCS5 13 MCS0 14 MCS5 14 MCS0 13 MCS5 13 MCS0 802.11ac VHT80 Tgtpwr
(dBm) 12 MCS5 12 Receiver Sensitivity Frequency Band Rate MCS1 14 MCS6 14 MCS1 13 MCS6 13 MCS1 14 MCS6 14 MCS1 13 MCS6 13 MCS1 12 MCS6 12 2.4G 5G 11b-1M 11b-11M 11g-6M 11g-54M 11n-HT20MCS0 11n-HT20MCS7 11n-HT40MCS0 11n-HT40MCS7 11a-6M 11a-54M 11ac-VHT20MCS0 11ac-VHT20MCS7 11ac-VHT20MCS8 11ac-VHT40MCS0 11ac-VHT40MCS7 11ac-VHT40MCS9 11ac-VHT80MCS0 11ac-VHT80MCS7 Page 5/15 MCS2 14 MCS7 14 MCS2 13 MCS7 13 MCS2 14 MCS7 14 MCS2 13 MCS7 13 MCS2 12 MCS7 12 Condition PER < 8%
PER < 8%
PER < 10%
PER < 10%
PER < 10%
PER < 10%
PER < 10%
PER < 10%
PER < 10%
PER < 10%
PER < 10%
PER < 10%
PER < 10%
PER < 10%
PER < 10%
PER < 10%
PER < 10%
PER < 10%
MCS3 14 MCS8 MCS3 13 MCS8 MCS3 14 MCS8 14 MCS3 13 MCS8 13 MCS3 12 MCS8 12 MCS4 14 MCS9 MCS4 13 MCS9 MCS4 14 MCS9 MCS4 13 MCS9 13 MCS4 12 MCS9 12 Typical (1SS)
(dBm)
-94
-86
-90
-73
-87
-70
-84
-67
-88
-71
-85
-68
-65
-82
-65
-61
-80
-63 11ac-VHT80MCS9 PER < 10%
-57 Security Common Function Operating Voltage Power Consumption Antenna Type WPS, WPA, WPA2, WEP 64bit & 128bit, IEEE 802.1X, IEEE 802.11i 3.3 V 10% I/O supply voltage Mode Average 5G 2.4G TBDmA TBDmA TBDmA TBDmA TBDmA TBDmA 2.4G 5G TX RX Unassocia ted Idle Triple U.FL connectors for WiFi&BT TBDmA Peak RECOMMENDED OPERATION CONDITIONS Symbol VDD33 VDD18 TAMNIENT 3.3V Supply Voltage 1.8V Supply Voltage Ambient Temperature Rating DC CHARACTERISTICS Symbol Parameter VIL VIH VOL VOH Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage POWER ON SEQUENCE TIMING Min 2.97 1.7
-10 Min
-0.28 2.0
-0.28 2.9 Typ 3.3 1.8
-
Typ
-
-
-
-
Max 3.63 1.9 70 Max 0.6 3.63 0.4 3.63 Units V V 0C Units V V V Page 6/15 PIN ASSIGMENT Pin. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Pin Define
+3.3V
+3.3V USB_D-
USB_D+
GND RESET#
WoWLAN#
GND WoBT GND GND GND GND GND FOOTPRINT Top View Description 3.3V source 3.3V source USB Data-
USB Data+
Ground System reset MT7668BU, low active Wake up system via wifi, low active Ground Wake up system via BT, low active Ground Ground Ground Ground Ground Status YES YES YES YES YES YES YES YES YES YES YES YES YES YES Page 7/15 MECHANICAL EEPROM INFORMATION WI-FI World Wide 2.4G/5G Read from registry; Control by driver Offset 0x38 for 5G: 0xFF Offset 0x39 for 2.4G: 0xFF 0x0E8D 0x7668 Reg Domain Vendor ID Device ID ENVIRONMENTAL OPERATING Ambient Operating Temperature: -10 to 70 C (14 to 158 F) Ambient Relative Humidity: 5-90% (non-condensing) STORAGE Ambient Temperature: -40 to 80 C (-40 to 176 F) Ambient Relative Humidity: 5-95% (non-condensing Page 8/15 WARNINGS FCC Statement:
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without C2P. This device is restricted for indoor use. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter Page 9/15 IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. 20 cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. This device is restricted to indoor use. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: PPQ-WCBN3509R ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device Page 10/15 complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. Lappareil ne doit pas produire de brouillage;
Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux tats-Unis / Canada du march, seul le canal 1 11 peuvent tre exploits. Slection d'autres canaux n'est pas possible. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with IC multi-transmitter product procedures. Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without reassessment permissive change. Cet appareil et son antenne (s) ne doit pas tre co-localiss ou fonctionnement en association avec une autre antenne ou transmetteur. The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Page 11/15 The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate. le gain maximal dantenne permis (pour les dispositifs utilisant la bande 5725-5850 MHz) doit se conformer la limite de p.i.r.e. spcifie pour lexploitation point point et non point point, selon le cas. Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 5650-5725 MHz. Slection dynamique de frquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-5600 MHz et 5650-5725 MHz. The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit. le gain maximal dantenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer la limite de p.i.r.e. Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. For indoor use only. Pour une utilisation en intrieur uniquement. IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This radio transmitter (IC: 4491A-WCBN3509R) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, Page 12/15 having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (IC: 4491A-WCBN3509R) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. The transmitter module may not be co-located with any other transmitter or antenna. Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. The transmitter module may not be co-located with any other transmitter or antenna. Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX IC :
4491A-WCBN3509R". Page 13/15 Table for Filed Antenna Page 14/15 Japan Statement:
5GHz product for indoor use only. CE Statement:
This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Page 15/15
This product uses the FCC Data API but is not endorsed or certified by the FCC