WP8333V5 802.11ac Tri Band PoE Access Point User Manual

WP8333V5 Getting Started Guide Package Contents You should have received the following components in your WP8333V5 package. Mounting the WP8333V5 1. Affix bracket to T - Grid. 2. Rotate bracket to snap on to T- Grid. 3. Place the first mounting post on the rear-side of the device on to the lower notch of the bracket. 4. Rotate the device such that all the mounting posts on the rear-side of the device are snapped in to the respective notches on the bracket. Getting the WP8333V5 Online Step 1: Power up If using PoE, plug one end of the Ethernet cable into the PoE switch or injector and plug the other end into the Ethernet + PoE port (LAN1) on the C-110. Make sure the PoE source you are using is turned ON. OR As an alternative to PoE, insert the power adapter plug into an AC power outlet and the other end into the power input port on the unit. Warning: If powering the device with PoE, ensure that the device is connected to a UL listed indoor PoE source. If not using PoE, ensure that you use only an AC power adapter supported by accessing point

(AP). Step 2: Connect to the network If you are using PoE, then the unit should already be connected to your network. If you are not using PoE, then plug one end of the Ethernet cable into an Ethernet jack on your network and the other end into the Ethernet port (LAN1) on the unit. Step 3: Check the LED status Wait for a few minutes till the LEDs for Power and Ethernet (LAN1) turn solid GREEN, which indicates that the unit is online and operational. Troubleshooting LED Power Status Description Solid Green Power On Off Power Off LAN1 Solid Green Device connected to LAN port 1 at 10/100/1000 Mbps Blinking Green Activity on LAN port 1 LAN2 Solid Green Device connected to LAN port 2 at 10/100/1000 Mbps 2.4 GHz Blinking Green Activity on LAN port 2 Solid Green No activity on 2.4 GHz radio Blinking Green Wireless activity on 2.4 GHz radio 5 GHz Solid Green No activity on 5 GHz radio Blinking Green Wireless activity on 5 GHz radio Radio 3 Blinking Green Activity on third radio For FCC Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two con-

ditions: (1) This device may not cause harmful interference, and (2) this device must accept any inter-

ference received, including interference that may cause undesired operation. This device is restricted for indoor use. IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum dis tance 22cm between the radiator & your body. For IC This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is sub. ject to the following two conditions:

(1) This device may not cause interference. tion of the device.

(2) This device must accept any interference, including interference that may cause undesired opera Cet appareil contient des metteurs / rcepteurs exempts de licence qui sont conformes au (x) RSS (s) exempts de licence d'Innovation, Sciences et Dveloppement conomique Canada. L'opration est soumise aux deux conditions suivantes:

(1) Cet appareil ne doit pas provoquer d'interfrences.

(2) Cet appareil doit accepter toute interfrence, y compris les interfrences susceptibles de provoquer un fonctionnement indsirable de l'appareil. The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. IMPORTANT NOTE:

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled envi ronment. This equipment should be installed and operated with minimum distance 28cm between the radiator & your body. Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 28cm de distance entre la source de rayonnement et votre corps. For JP 5GHz band (W52, W53): Indoor use only (except communicate to high power radio)