PRODUCT SPECIFICATION 802.11n, 2.4G 1T1R Wireless LAN USB Module WN4614L Realtek RTL8188ETV Version 1.0 User Manual
* This document contains confidential proprietary information and is property of LTC. The contents of this document should not be disclosed to unauthorized persons without the written consent of LTC. Page 1/12 CONTENT FCC WARING STATEMENT .......................................................................................................... 3 IC WARING STATEMENT .............................................................................................................. 4 PRODUCT FEATURES .................................................................................................................... 5 WI-FI FEATURE .................................................................................................................................... 5 INTRODUCTION .............................................................................................................................. 6 SOFTWARE INSTALLATION ........................................................................................................ 7 HARDWARE INSTALLATION ..................................................................................................... 10 NETWORK CONNECTION ........................................................................................................... 10 Page 2/12 FCC WARING STATEMENT FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that may cause undesired operation. RF exposure warning This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instructions and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Page 3/12 End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains FCC ID:
PPQ-WN41L Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1) This device is intended for OEM integrators only. 2) Please see the full Grant of Equipment document for other restrictions. This device is operation in 5.15 5.25GHz frequency range, then restricted in indoor use only, Outdoor operations in the 5150~5250MHz is prohibit. This device is slave equipment, the device is not radar detection and not ad-hoc operation in the DFS band. IC WARING STATEMENT Canada, avis d'Industry Canada (IC) Cet appareil numrique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interfrence et (2) cet appareil doit accepter toute interfrence, notamment les interfrences qui peuvent affecter son fonctionnement. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person's body). Page 4/ 12 Informations concernant l'exposition aux frquences radio (RF) La puissance de sortie mise par lappareil de sans fil est infrieure la limite d'exposition aux frquences radio d'Industry Canada (IC). Utilisez lappareil de sans fil de faon minimiser les contacts humains lors du fonctionnement normal. Ce priphrique a galement t valu et dmontr conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition des appareils mobiles (les antennes se situent moins de 20 cm du corps d'une personne). PRODUCT FEATURES Wi-Fi Feature Operate at ISM frequency Band (2.4GHz) IEEE Standards Support, 802.11b, 802.11g and 802.11n CMOS MAC, Baseband PHY, and RF in a single chip for IEEE 802.11b/g/n compatible WLAN Complies with USB Specification 2.0, support Full-speed(12Mbps) and High-Speed(480Mbps) Enterprise level security supporting: WPA, WPA2 Support 1 transmission and 1 receiving, transmission rate can up to 150Mbps
(Physical Rate) in downstream and upstream RoHS compliance Low Halogen compliance Page 5/ 12 INTRODUCTION The 802.11b/g/n 1T1R USB WLAN Card is a device that allows you connect your computer to a wireless local area network (LAN). A wireless LAN allows your system to use wireless Radio Frequency (RF) technology to transmit and receive data without physically attaching to the network. The Wireless protocols that come with this product ensure data security and isolation from interference generated by other radio frequencies. This card also allows you to take full advantage of your computers mobility with access to real-time information and online services anytime and anywhere. In addition, this device eliminates the bother of pulling cable through walls and under furniture. It even allows you to place your system in locations where cabling is impossible. Modifying and augmenting networks has never been so easy. Wireless Network Options The Peer-to-Peer Network This network installation lets you set a small wireless workgroup easily and quickly. Equipped with wireless PC Cards or wireless PCI, you can share files and printers between each PC and laptop. You can also use one computer as an Internet Server to connect to a wired global network and share files and information with other computers via a wireless LAN. The Access Point Network Page 6/12 The network installation allows you to share files, printers, and Internet access much more conveniently. With Wireless LAN Cards, you can connect wireless LAN to a wired global network via an Access Point. SOFTWARE INSTALLATION Install the device 1.Make sure the computer is turned off. Remove the expansion slot cover from the computer. 2.Carefully slide the 802.11b/g/n 1T1R USB WLAN Card into the USB port. Push evenly and slowly and ensure it is properly seated. 3.After the device has been connected to your computer, turn on your computer. Windows will detect the new hardware and then automatically copy all of the files needed for networking. Page 7/12 Install the Driver & Utility 1.Exit all Windows programs. Insert the included CD-ROM into your computer. The CD-ROM will run automatically. 2.When the License Agreement screen appears, please read the contents and select I accept the terms of the license agreement then click Next to continue. Page 8/12 3.Click the Install to continue 4.When the following screen appears, click Finish to complete thesoftware installation. Page 9/12 HARDWARE INSTALLATION Verification To verify if the device exists in your computer and is enabled, go to Start >
Control Panel > System (> Hardware) > Device Manager. Expand the Network Adapters category. If the 802.11n 1T2R Wireless LAN Card is listed here, it means that your device is properly installed and enabled. NETWORK CONNECTION Once the device driver is well installed, a network setting described in the following should be also established. 1.Click the Wireless icon to enable Windows Zero Configure. 2.Select the AP then click the Connect Page 10/12 Page 11/12 3.Surfing the Internet after completing connection. Page 12/12