E8197 LED security light user manual

 

Sku Number: 356-9258 OUTDOOR SECURITY LIGHT Model Number: E8197W Questions, problems, missing parts?

Before returning to your retailer, call our customer service at 1-800-887-6326 Monday Friday 9:00 a.m. 5:00 p.m. CST PACKAGE CONTENTS B A C D HARDWARE CONTENTS Note: Hardware not shown actual size. AA

#8/32 X 1/2 in

#6/32 X 1/2 in

#10/24 X 1/4 in CC EE Mounting Screw X2 Mounting Strap X1 Fixture Mounting Screw X1 BB DD FF Mounting Bracket Screw X1 Decorative cover X1 Wire Connector X2 Page 1 of 16 190717 SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. WARNING Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or switching off circuit breaker). Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury or death from electric shock. LED electronics can be damaged by electro static discharge (ESD)shock. Before installation, discharge yourself by touching a grounded bare metal surface to remove this hazard. To avoid damage, do not touch the LED module. CAUTION All electrical connections must be in agreement with local codes, ordinances or the national electric code (NEC). Contact your municipal building department to learn about your local codes, permits and/or inspections. Risk of fire most dwellings built before 1985 have supply wire rated for 140F/60C. Consult a qualified electrician before installation. Only general ON/OFF wall switch applies for this fixture, the dimmable wall switch shouldnt be required. Maximum Wattage: 29 W Working Temperature Range: -4F ~ 113F PREPARATION Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with package contents list and diagram on previous page. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts. Tools Required for Assembly (not included): Screwdriver, Phillips Screwdriver, Pliers, Electrical Tape, Wire Cutters, Safety Glasses, Ladder, Wire Stripper. ASSEMBLY INSTRUCTIONS Important to Know 1. This fixture requires a 120 VAC, 60 Hz power source. 2. For general safety and to avoid any possible damage to the sensor, be sure the power is switched "off" before adjustment. 3. Motion sensor: turns light ON automatically when motion is detected and turns light OFF automatically when motion stops. 4. Photocell keeps the light OFF during daylight hours. Note: Fixture can be wall mounted or eave mounted. Wall Mounted Eave Mounted Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation) Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for proper operation and to avoid the risk of electrical shock. Page 2 of 16 190717 ASSEMBLY INSTRUCTIONS (continued) For eave mounted only:

Swing the sensor head towards the mounting bracket. Mounting Bracket Controls Controls Controls Installation Steps Turn off the power at fuse or circuit box. 1. The fixture mounting bracket (A) is pre-assembled on the light fixture (B). Unscrew both the decorative cover (DD) and the fixture mounting screw (EE) in order to remove the mounting bracket (A). 1 DD EE A B FF 3 Outlet Box 3. Pull out the source wires from the outlet box. Make wire connections using wire connectors (FF) as follows:

---Connect the black wire from the fixture to the hot wire from the power source.

---Connect the white wire from the fixture to the neutral wire from the power source. Carefully tuck the wires back into the outlet box. FRONT A AA 2 2. Install the mounting strap (CC) to the outlet box with the stamped word FRONT facing away from the outlet box, using two mounting screws

(AA) that best fit the outlet box. Mounting bracket(A) should sit flush against wall surface when secured. (Choose one matching pair of suitable mounting screws (AA) from the 3 pairs provided). CC 4. Place mounting bracket (A) against the outlet box, insert the mounting bracket screw

(BB) through the mounting bracket hole, thread mounting bracket screw (BB) into the center hole of the mounting strap(CC). Tighten the mounting bracket screw (BB) securely. 4 Outlet Box FF A BB CC When mounting to a wall, the UP arrow must point upward. When mounting to an eave, the UP arrow must point toward the building. 5. Attach the backplate(B) of the light fixture to the mounting bracket(A), secure it with the fixture mounting screw(EE). Then push the decorative cover

(DD) firmly into the fixture mounting screw (EE) hole on the light fixture. 5 DD EE A B Turn on the power at fuse or circuit box. 6. With silicone caulking compound, caulk completely around where the mounting bracket meets the wall surface. CAUTION: Be sure to caulk completely where the mounting bracket meets the wall surface to prevent water from seeping into the outlet box. 6 Page 3 of 16 190717 ASSEMBLY INSTRUCTIONS (continued) Adjusting the Sensor Head:

1. a: Aim sensor head toward desired detection area, maintaining a 5 - 40 downward angle to allow moisture to drain. (See Fig.1) Note: Make sure sensor head is positioned with control knob facing towards the ground. Fig.1 the detection zone at the farthest distance you wish to detect motion. D 2. Range set too high may increase false triggering.

(See Fig.2-1, 2-2) Fig.2-1 Fig.2-2 Adjusting the Light Head:

1. Gently grasp the light heads(C) and tilt them up or down, left or right to adjust the light Fig.3 C Adjustment Sensor Higher For Long Coverage Adjustment Sensor Lower For Short Coverage 6H PC 30s Test 1min 3 min L M H Auto 3H Time Fig. 4 Mode Sens Sensitivity of Motion Sensor:

1. You can adjust the sensitivity of the motion sensor by using the SENS selector located on the bottom surface of the sensor. (See Fig.4) 2. Adjust motion sensor sensitivity to HIGH (H), MEDIUM (M), or LOW (L) to achieve desired performance. 3. Approximate range for each setting: 25 ft. (L), 45 ft. (M), 70 ft. (H). Choose a mode by sliding the switch on the bottom of the sensor. (See Fig.4) Note: When power is first applied, the light will turn on to 100% brightness. The sensor will take 30 seconds to warm up. 1. TEST mode (daytime or nighttime operation )

(cid:3)(cid:3)(cid:3)(cid:3)(cid:404)(cid:3)(cid:3)(cid:54)(cid:79)(cid:76)(cid:71)(cid:72)(cid:3)(cid:87)(cid:75)(cid:72)(cid:3)(cid:86)(cid:90)(cid:76)(cid:87)(cid:70)(cid:75)(cid:3)(cid:82)(cid:81)(cid:3)(cid:87)(cid:75)(cid:72)(cid:3)(cid:85)(cid:76)(cid:74)(cid:75)(cid:87)(cid:3)(cid:86)(cid:76)(cid:71)(cid:72)(cid:3)(cid:82)(cid:73)(cid:3)(cid:87)(cid:75)(cid:72)(cid:3)(cid:86)(cid:72)(cid:81)(cid:86)(cid:82)(cid:85)(cid:3)(cid:87)(cid:82)(cid:3)(cid:87)(cid:75)(cid:72)(cid:3)(cid:179)(cid:55)(cid:40)(cid:54)(cid:55)(cid:180)(cid:3)(cid:83)(cid:82)(cid:86)(cid:76)(cid:87)(cid:76)(cid:82)(cid:81)(cid:17)(cid:3)(cid:11)(cid:54)(cid:72)(cid:72)(cid:3)(cid:41)(cid:76)(cid:74)(cid:17)(cid:23)(cid:12)

(cid:3)(cid:3)(cid:3)(cid:3)(cid:404)(cid:3)(cid:3)(cid:58)(cid:76)(cid:87)(cid:75)(cid:3)(cid:87)(cid:75)(cid:72)(cid:3)(cid:83)(cid:82)(cid:90)(cid:72)(cid:85)(cid:3)(cid:82)(cid:81)(cid:15)(cid:3)(cid:87)(cid:75)(cid:72)(cid:3)(cid:79)(cid:76)(cid:74)(cid:75)(cid:87)(cid:3)(cid:87)(cid:88)(cid:85)(cid:81)(cid:86)(cid:3)(cid:87)(cid:82)(cid:3)(cid:79)(cid:82)(cid:90)(cid:16)(cid:79)(cid:72)(cid:89)(cid:72)(cid:79)(cid:3)(cid:69)(cid:85)(cid:76)(cid:74)(cid:75)(cid:87)(cid:81)(cid:72)(cid:86)(cid:86)(cid:3)(cid:68)(cid:88)(cid:87)(cid:82)(cid:80)(cid:68)(cid:87)(cid:76)(cid:70)(cid:68)(cid:79)(cid:79)(cid:92)(cid:17)

(cid:3)(cid:3)(cid:3)(cid:3)(cid:404)(cid:3)(cid:3)(cid:55)(cid:75)(cid:72)(cid:3)(cid:79)(cid:76)(cid:74)(cid:75)(cid:87)(cid:3)(cid:87)(cid:88)(cid:85)(cid:81)(cid:86)(cid:3)(cid:87)(cid:82)(cid:3)(cid:75)(cid:76)(cid:74)(cid:75)(cid:16)(cid:79)(cid:72)(cid:89)(cid:72)(cid:79)(cid:3)(cid:69)(cid:85)(cid:76)(cid:74)(cid:75)(cid:87)(cid:81)(cid:72)(cid:86)(cid:86)(cid:3)(cid:90)(cid:75)(cid:72)(cid:81)(cid:3)(cid:80)(cid:82)(cid:87)(cid:76)(cid:82)(cid:81)(cid:3)(cid:76)(cid:86)(cid:3)(cid:71)(cid:72)(cid:87)(cid:72)(cid:70)(cid:87)(cid:72)(cid:71)(cid:15)(cid:3)(cid:68)(cid:81)(cid:71)(cid:3)(cid:86)(cid:87)(cid:68)(cid:92)(cid:86)(cid:3)(cid:82)(cid:81)(cid:3)(cid:68)(cid:86)(cid:3)(cid:79)(cid:82)(cid:81)(cid:74)(cid:3)(cid:68)(cid:86)(cid:3)(cid:87)(cid:75)(cid:72)(cid:3)(cid:80)(cid:82)(cid:87)(cid:76)(cid:82)(cid:81)(cid:3)(cid:70)(cid:82)(cid:81)(cid:87)(cid:76)(cid:81)(cid:88)(cid:72)(cid:86)(cid:17)(cid:3) Then it reverts back to low-level brightness about 5 seconds after motion is no longer detected. 2. AUTO MODE (nighttime operation only)

(cid:3)(cid:3)(cid:3)(cid:3)(cid:404)(cid:3)(cid:55)(cid:82)(cid:3)(cid:86)(cid:75)(cid:76)(cid:73)(cid:87)(cid:3)(cid:87)(cid:82)(cid:3)(cid:179)(cid:36)(cid:56)(cid:55)(cid:50)(cid:180)(cid:3)(cid:80)(cid:82)(cid:71)(cid:72)(cid:15)(cid:3)(cid:86)(cid:79)(cid:76)(cid:71)(cid:72)(cid:3)(cid:55)(cid:76)(cid:80)(cid:72)(cid:3)(cid:39)(cid:72)(cid:79)(cid:68)(cid:92)(cid:3)(cid:86)(cid:90)(cid:76)(cid:87)(cid:70)(cid:75)(cid:3)(cid:87)(cid:82)(cid:3)(cid:87)(cid:75)(cid:72)(cid:3)(cid:71)(cid:72)(cid:86)(cid:76)(cid:85)(cid:72)(cid:71)(cid:3)(cid:87)(cid:76)(cid:80)(cid:72)(cid:3)(cid:86)(cid:72)(cid:87)(cid:87)(cid:76)(cid:81)(cid:74)(cid:3)

(30s/1min/3min). At dusk, the light turns on to pre-selected low level brightness and CCT color. When motion is detected, the light turns to full brightness and stays on as long as motion continues. When the motion is no longer detected, the light stays on high-level brightness for the predetermined time you set

(30s/1min//5min), and then switches back to low level automatically.

(cid:3)(cid:3)(cid:3)(cid:3)(cid:404)(cid:3)(cid:55)(cid:75)(cid:72)(cid:3)(cid:79)(cid:76)(cid:74)(cid:75)(cid:87)(cid:3)(cid:87)(cid:88)(cid:85)(cid:81)(cid:86)(cid:3)(cid:82)(cid:73)(cid:73)(cid:3)(cid:68)(cid:88)(cid:87)(cid:82)(cid:80)(cid:68)(cid:87)(cid:76)(cid:70)(cid:68)(cid:79)(cid:79)(cid:92)(cid:3)(cid:68)(cid:87)(cid:3)(cid:71)(cid:68)(cid:90)(cid:81)(cid:17) 3. 3 HOURS (3H) MODE (nighttime operation only)

(cid:3)(cid:3)(cid:3)(cid:3)(cid:404)(cid:3)(cid:55)(cid:75)(cid:72)(cid:3)(cid:79)(cid:76)(cid:74)(cid:75)(cid:87)(cid:3)(cid:87)(cid:88)(cid:85)(cid:81)(cid:86)(cid:3)(cid:87)(cid:82)(cid:3)(cid:75)(cid:76)(cid:74)(cid:75)(cid:16)(cid:79)(cid:72)(cid:89)(cid:72)(cid:79)(cid:3)(cid:69)(cid:85)(cid:76)(cid:74)(cid:75)(cid:87)(cid:81)(cid:72)(cid:86)(cid:86)(cid:3)(cid:11)(cid:20)(cid:19)(cid:19)(cid:8)(cid:12)(cid:3)(cid:68)(cid:81)(cid:71)(cid:3)(cid:83)(cid:85)(cid:72)(cid:16)(cid:86)(cid:72)(cid:79)(cid:72)(cid:70)(cid:87)(cid:72)(cid:71)(cid:3)(cid:38)(cid:38)(cid:55)(cid:3)(cid:70)(cid:82)(cid:79)(cid:82)(cid:85)(cid:3)(cid:68)(cid:87)(cid:3)(cid:71)(cid:88)(cid:86)(cid:78)(cid:15)(cid:3)(cid:68)(cid:81)(cid:71)(cid:3)(cid:86)(cid:87)(cid:68)(cid:92)(cid:86)(cid:3)(cid:5)(cid:50)(cid:49)(cid:5)(cid:3)(cid:73)(cid:82)(cid:85)(cid:3)(cid:22)(cid:3)(cid:75)(cid:82)(cid:88)(cid:85)(cid:86)(cid:17)(cid:3)

(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:55)(cid:75)(cid:72)(cid:81)(cid:3)(cid:76)(cid:87)(cid:3)(cid:87)(cid:88)(cid:85)(cid:81)(cid:86)(cid:3)(cid:87)(cid:82)(cid:3)(cid:79)(cid:82)(cid:90)(cid:16)(cid:79)(cid:72)(cid:89)(cid:72)(cid:79)(cid:3)(cid:69)(cid:85)(cid:76)(cid:74)(cid:75)(cid:87)(cid:81)(cid:72)(cid:86)(cid:86)(cid:17)(cid:3)(cid:44)(cid:87)(cid:3)(cid:87)(cid:88)(cid:85)(cid:81)(cid:86)(cid:3)(cid:87)(cid:82)(cid:3)(cid:75)(cid:76)(cid:74)(cid:75)(cid:16)(cid:79)(cid:72)(cid:89)(cid:72)(cid:79)(cid:3)(cid:69)(cid:85)(cid:76)(cid:74)(cid:75)(cid:87)(cid:81)(cid:72)(cid:86)(cid:86)(cid:3)(cid:11)(cid:20)(cid:19)(cid:19)(cid:8)(cid:3)(cid:24)(cid:19)(cid:19)(cid:19)(cid:46)(cid:12)(cid:3)(cid:90)(cid:75)(cid:72)(cid:81)(cid:3)(cid:80)(cid:82)(cid:87)(cid:76)(cid:82)(cid:81)(cid:3)(cid:76)(cid:86)(cid:3)(cid:71)(cid:72)(cid:87)(cid:72)(cid:70)(cid:87)(cid:72)(cid:71)(cid:15)(cid:3)(cid:68)(cid:81)(cid:71) stays on as long as motion continues. When motion is no longer detected, it remains on for the predetermined shut-off delay time you set (30s/1min/3min), and then returns to the predetermined low-level brightness automatically.

(cid:3)(cid:3)(cid:3)(cid:3)(cid:404)(cid:3)(cid:55)(cid:75)(cid:72)(cid:3)(cid:79)(cid:76)(cid:74)(cid:75)(cid:87)(cid:3)(cid:87)(cid:88)(cid:85)(cid:81)(cid:86)(cid:3)(cid:82)(cid:73)(cid:73)(cid:3)(cid:68)(cid:88)(cid:87)(cid:82)(cid:80)(cid:68)(cid:87)(cid:76)(cid:70)(cid:68)(cid:79)(cid:79)(cid:92)(cid:3)(cid:68)(cid:87)(cid:3)(cid:71)(cid:68)(cid:90)(cid:81)(cid:17) 4. 6 HOURS (6H) MODE (nighttime operation only)

(cid:3)(cid:3)(cid:3)(cid:3)(cid:404)(cid:3)(cid:55)(cid:75)(cid:72)(cid:3)(cid:79)(cid:76)(cid:74)(cid:75)(cid:87)(cid:3)(cid:87)(cid:88)(cid:85)(cid:81)(cid:86)(cid:3)(cid:87)(cid:82)(cid:3)(cid:75)(cid:76)(cid:74)(cid:75)(cid:16)(cid:79)(cid:72)(cid:89)(cid:72)(cid:79)(cid:3)(cid:69)(cid:85)(cid:76)(cid:74)(cid:75)(cid:87)(cid:81)(cid:72)(cid:86)(cid:86)(cid:3)(cid:11)(cid:20)(cid:19)(cid:19)(cid:8)(cid:12)(cid:3)(cid:68)(cid:81)(cid:71)(cid:3)(cid:83)(cid:85)(cid:72)(cid:16)(cid:86)(cid:72)(cid:79)(cid:72)(cid:70)(cid:87)(cid:72)(cid:71)(cid:3)(cid:38)(cid:38)(cid:55)(cid:3)(cid:70)(cid:82)(cid:79)(cid:82)(cid:85)(cid:3)(cid:68)(cid:87)(cid:3)(cid:71)(cid:88)(cid:86)(cid:78)(cid:15)(cid:3)(cid:68)(cid:81)(cid:71)(cid:3)(cid:86)(cid:87)(cid:68)(cid:92)(cid:86)(cid:3)(cid:5)(cid:50)(cid:49)(cid:5)(cid:3)(cid:73)(cid:82)(cid:85)(cid:3)(cid:25)(cid:3)(cid:75)(cid:82)(cid:88)(cid:85)(cid:86)(cid:17)(cid:3)

(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:55)(cid:75)(cid:72)(cid:81)(cid:3)(cid:76)(cid:87)(cid:3)(cid:87)(cid:88)(cid:85)(cid:81)(cid:86)(cid:3)(cid:87)(cid:82)(cid:3)(cid:79)(cid:82)(cid:90)(cid:16)(cid:79)(cid:72)(cid:89)(cid:72)(cid:79)(cid:3)(cid:69)(cid:85)(cid:76)(cid:74)(cid:75)(cid:87)(cid:81)(cid:72)(cid:86)(cid:86)(cid:17)(cid:3)(cid:44)(cid:87)(cid:3)(cid:87)(cid:88)(cid:85)(cid:81)(cid:86)(cid:3)(cid:87)(cid:82)(cid:3)(cid:75)(cid:76)(cid:74)(cid:75)(cid:16)(cid:79)(cid:72)(cid:89)(cid:72)(cid:79)(cid:3)(cid:69)(cid:85)(cid:76)(cid:74)(cid:75)(cid:87)(cid:81)(cid:72)(cid:86)(cid:86)(cid:3)(cid:11)(cid:20)(cid:19)(cid:19)(cid:8)(cid:3)(cid:24)(cid:19)(cid:19)(cid:19)(cid:46)(cid:12)(cid:3)(cid:90)(cid:75)(cid:72)(cid:81)(cid:3)(cid:80)(cid:82)(cid:87)(cid:76)(cid:82)(cid:81)(cid:3)(cid:76)(cid:86)(cid:3)(cid:71)(cid:72)(cid:87)(cid:72)(cid:70)(cid:87)(cid:72)(cid:71)(cid:15)(cid:3)(cid:68)(cid:81)(cid:71)(cid:3) stays on as long as motion continues. When motion is no longer detected, it remains on for the predetermined shut-off delay time you set (30s/1min/3min), and then returns to the predetermined low-level brightness automatically.

(cid:3)(cid:3)(cid:3)(cid:404)(cid:3)(cid:55)(cid:75)(cid:72)(cid:3)(cid:79)(cid:76)(cid:74)(cid:75)(cid:87)(cid:3)(cid:87)(cid:88)(cid:85)(cid:81)(cid:86)(cid:3)(cid:82)(cid:73)(cid:73)(cid:3)(cid:68)(cid:88)(cid:87)(cid:82)(cid:80)(cid:68)(cid:87)(cid:76)(cid:70)(cid:68)(cid:79)(cid:79)(cid:92)(cid:3)(cid:68)(cid:87)(cid:3)(cid:71)(cid:68)(cid:90)(cid:81)(cid:17) Page 4 of 16 190717 ASSEMBLY INSTRUCTIONS (continued) ASSEMBLY INSTRUCTIONS (continued) FUNCTION AND OPERATION 5. PHOTOCELL (PC) MODE (nighttime operation only)

(cid:404)(cid:3)(cid:55)(cid:75)(cid:72)(cid:3)(cid:79)(cid:76)(cid:74)(cid:75)(cid:87)(cid:3)(cid:87)(cid:88)(cid:85)(cid:81)(cid:86)(cid:3)(cid:82)(cid:81)(cid:3)(cid:87)(cid:82)(cid:3)(cid:73)(cid:88)(cid:79)(cid:79)(cid:3)(cid:69)(cid:85)(cid:76)(cid:74)(cid:75)(cid:87)(cid:81)(cid:72)(cid:86)(cid:86)(cid:3)(cid:68)(cid:87)(cid:3)(cid:71)(cid:88)(cid:86)(cid:78)(cid:3)(cid:68)(cid:81)(cid:71)(cid:3)(cid:85)(cid:72)(cid:80)(cid:68)(cid:76)(cid:81)(cid:86)(cid:3)(cid:179)(cid:50)(cid:49)(cid:180)(cid:3)(cid:88)(cid:81)(cid:87)(cid:76)(cid:79)(cid:3)(cid:71)(cid:68)(cid:90)(cid:81)(cid:17) 6. 3Min/10Min dual timer

(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:404)(cid:3)(cid:58)(cid:75)(cid:72)(cid:81)(cid:3)(cid:87)(cid:75)(cid:72)(cid:3)(cid:79)(cid:76)(cid:74)(cid:75)(cid:87)(cid:3)(cid:82)(cid:81)(cid:3)(cid:73)(cid:82)(cid:85)(cid:3)(cid:22)(cid:80)(cid:76)(cid:81)(cid:3)(cid:70)(cid:82)(cid:80)(cid:72)(cid:86)(cid:3)(cid:87)(cid:82)(cid:3)(cid:87)(cid:75)(cid:72)(cid:3)(cid:72)(cid:81)(cid:71)(cid:15)(cid:3)(cid:87)(cid:75)(cid:72)(cid:3)(cid:79)(cid:76)(cid:74)(cid:75)(cid:87)(cid:3)(cid:90)(cid:76)(cid:79)(cid:79)(cid:3)(cid:73)(cid:79)(cid:68)(cid:86)(cid:75)(cid:3)

(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:87)(cid:90)(cid:76)(cid:70)(cid:72)(cid:3)(cid:68)(cid:81)(cid:71)(cid:3)(cid:71)(cid:76)(cid:80)(cid:3)(cid:71)(cid:82)(cid:90)(cid:81)(cid:3)(cid:87)(cid:82)(cid:3)(cid:21)(cid:19)(cid:8)(cid:3)(cid:69)(cid:85)(cid:76)(cid:74)(cid:75)(cid:87)(cid:81)(cid:72)(cid:86)(cid:86)(cid:3)(cid:73)(cid:82)(cid:85)(cid:3)(cid:21)(cid:19)(cid:3)(cid:86)(cid:72)(cid:70)(cid:82)(cid:81)(cid:71)(cid:86)(cid:15)(cid:3)(cid:71)(cid:88)(cid:85)(cid:76)(cid:81)(cid:74)(cid:3)(cid:87)(cid:75)(cid:76)(cid:86) time, if the sensor detects additional motion, the light will continue to stay on for 10min, and so on. Notes:

1. The sensitivity of the motion sensor will increase as the environmental temperature gets cooler. You may wish to make adjustments when the season changes. For best performance, gently clean the lens with a soft cloth every 1 or 2 months to assure maximum sensitivity. 2. For best performance, install fixture at least 8 feet above the ground. At such a height, the fixture will provide a detection distance of up to 70 feet at 77 degrees Fahrenheit. (See Fig.6) 3. The sensor detects movement across a detection range of 240 degrees. (See Fig.7) 4. The sensor will be more sensitive to motion across its detection path than motion directly towards it. (See Fig.8) 5. To reduce possible nuisances, do not mount the fixture near a heat source like an air conditioner, vent or furnace exhaust, or in a direction facing any reflecting object or other light source. Where you install your fixture is important:

Be sure the light is mounted straight on the wall or eave; otherwise, the detection distance may be limited. 12.0'

8.0'

Fig. 8 Fig. 6 Fig. 7 240'

25'

70'

Motion Motion Least sensitive Sensor Most sensitive Page 5 of 16 190717 USER GUIDE Se(cid:427)ng for single light through mobile device (Take iOS for example as below. Android will be slightly di(cid:299)erent). Before you strat 1. Download the Dualux BT App from the Apple App Store or Android Google Play store. 2. Launch the App and tap Wifi. 1 Back 9:41 AM

(cid:20)(cid:19)(cid:19)(cid:8) Dualux 3. Tap Register for new accounts or Login for existing accounts. 9:41 AM

(cid:20)(cid:19)(cid:19)(cid:8) Back 4. Enter E-Mail address, then tap Next. 5. Tap Register for new accounts or Login for existing accounts. Take photo Choose existing photo Cancel 6. Install & power On light then tap Search for lights. 9:41 AM

(cid:20)(cid:19)(cid:19)(cid:8) Back Take photo Choose existing photo Cancel 3 5 Take photo Choose existing photo Cancel 9:41 AM

(cid:20)(cid:19)(cid:19)(cid:8) Back Take photo Choose existing photo Cancel 9:41 AM

(cid:20)(cid:19)(cid:19)(cid:8) Back Take photo Choose existing photo Cancel 2 4 6 Page 6 of 16 190717 USER GUIDE (continued) 7. Power On the light and confirm the green indicator light is blinking. Then tap next. 9:41 AM

(cid:20)(cid:19)(cid:19)(cid:8) Back 8. Choose a 2.4GHz WiFi network and enter the WiFi password, then tap Confirm. Note: Only works with 2.4GHz WiFi networks. Take photo Choose existing photo Cancel 9. Connected to the lighting devices wifi (HF-XXXXXX). Tap Set wi-fi choose a HF-XXXXXX. 11. Successfully added device. To rename the light, tap the modify device name , enter the new name and tap confirm. The light(s) are now eady to be controlled with the dualux App. 7 9 11 10. The status window will appear once the device(s) have successfully connected and the 3 bullets on the bottom will followed by a tick. Note: If unsuccessful, the Failed to Add screen will appear. Close the App and repeat the previous steps. 9:41 AM

(cid:20)(cid:19)(cid:19)(cid:8) Back Take photo Choose existing photo Cancel 9:41 AM

(cid:20)(cid:19)(cid:19)(cid:8) Back 12. The new light will be shown in light list. And click icon, it will go to the setting list. Take photo Choose existing photo Cancel 9:41 AM

(cid:20)(cid:19)(cid:19)(cid:8) Back Take photo Choose existing photo Cancel 9:41 AM

(cid:20)(cid:19)(cid:19)(cid:8) Back Take photo Choose existing photo Cancel 9:41 AM

(cid:20)(cid:19)(cid:19)(cid:8) Back Take photo Choose existing photo Cancel 8 10 12 Page 7 of 16 190717 FUNCTION AND OPERATION (continued) 13. The Setting list, You can set up Functions, Change image, Rename light, and Restore factory defaults. 9:41 AM

(cid:20)(cid:19)(cid:19)(cid:8) Back Take photo Choose existing photo Cancel 13 14. Tap the Functions, You can choose Test, Auto, or Custom Setting. Select Test in Manual override and adjust Detection Distance , Brightness and CCT change as desired. Then click Save. 14 15. Select Auto in Manual override and adjust Motion Delay Time, Detection Distance , Brightness and CCT change as desired. Then click Save. 15 16. Select Custom Settings in Manual Override for Customize Early Evening Mode setting, and choose option between Duration or Clock Time (End Time) to set the continuous bright light illumination duration. Within Duration, you may set from 0 to 12 hours for continuous bright light once lamp is activated at night. In Clock Time (End Time), is the time you set to deactivate the continuous bright light according to the actual hour in the mobile device after the lamp is activated. Both option settings will return to motion-sensor operation after the continuous bright light is deactivate. 9:00 P.M. is the default in Clock Time (End Time). Note: "Duration" setting will only work once per setting, it automatically go into Clock Time (End Time) on the next day. Also if you do not click save for either option, then the settings will follow according to the switch control on the actual lamp. 16 Page 8 of 16 190717 FUNCTION AND OPERATION (continued) 17. Click Fig.13 Change image. And click take photo to take a photo. 18. Android:Click to grasp a your desired view. iOS:Click to grasp a your desired view. Cancel 17 19. Android:Click to take a photo. The iOs system does not have this step. 18 SOi 18 diordnA 20. Android:Adjust the photo to trim the photos desired size. Then click . iOS: ClickDone to take a photo. Crop picture 19 20 SOi 20 diordnA 21. It will turn to change image The photo will show on it.

(Android will be slightly different from the iOS system) 22. Go back to Light list, the photo will show on the left of Light 1. 21 22 Page 9 of 16 190717 FUNCTION AND OPERATION (continued) 23. Click fig.13 Change existing photo to choose a desired image on your device. Then click Cancel back to Setting menu list. 24. Click fig.13 Rename light to enter a name for the light, then click Save. Cancel 23 24 Restore factory defaults 25. Click fig.8 Restore factory defaults to restore your settings (only the light name and password) to the original conditions. Note: The photos settings cant be restored by using this function. 26. Remove the device from the light list. 25 26 Note: 1. Manual control and App control independently. 2. The function which is executed is the lastest settings. 3. After a power cut or power outage, the function of the light will revert back to the actual settings of the switches on the fixture. App settings will also revert back to the factory default. 4. For achieving the best performance, make sure the wall switch is in ON state (daytime and nighttime). Page 10 of 16 190717 FUNCTION AND OPERATION (continued) Connecting to Alexa 1. Sigin in with amazon alexa account. 2. Select your name or someone else. 3. Launch the Alexa App then tap on the Menu.

(In the upper left corner) 1 3 4. Select Skills & Games. 2 4 Page 11 of 16 190717 FUNCTION AND OPERATION (continued) 5. In the search menu type Innovation & Perfect. then tap Innovation & Perfect. 6. Tap ENABLE TO USE. 7. Enter the user name &

assword from the Innovation

& Perfect App. Then tap Login. 9. Discover your devices. 5 7 9 8.Get successful page and press cross. 10.Discover devices for 20 seconds 6 4 8 4 10 Page 12 of 16 190717 FUNCTION AND OPERATION (continued) 11. Discover a light and set up device. 12.Add your light to a group. 11 13. Select a group. 14. Light is added to a group. 16. New device is displayed in group. 15. Tap lights. 13 15 4 12 4 14 4 16 Page 13 of 16 190717 FUNCTION AND OPERATION (continued) Connecting to Google Home 1. Login Google Home with account. Press to add device 2. Tap set up device. 1 2 Page 14 of 16 190717 FUNCTION AND OPERATION (continued) 3. Select Works with Google. 4. Select[test] Innovation &

Perfect. 5. Enter the user name &

assword from the Innovation

& erfect App.Then tap Login. 7. Go back to main page. 4 6 7 6. Wait for signing in. 8. A device links to google home automatically. 5 7 8 Page 15 of 16 190717 FUNCTION AND OPERATION (continued) Range Sensing angle Electrical load - LED Lumens Power requirements Operating modes Time delay Mobile device requirements Up to 70ft. (Varies with surrounding temperature) Up to 240 32W 2600lm 120 VAC, 60Hz Test, Auto, 3H, 6H, PC 30s,1min,3min Iphone 4S or newer running IOS 8.0 x or later. Android v4.4 or later Phone must also have Bluetooth version 4.0 or later The following parts are available for reorder if damaged or missing. Call our toll-free at 1-800-887-6326. Spare Parts List:

AA BB Mounting Screw X2 Mounting Strip X1 CC DD Fixture Mounting Screw X1 Wire Connector X3 Assembly Kit 5569MM (1 SET) Page 16 of 16 190717 CARE AND MAINTENANCE To clean, turn off and wipe with a damp, non-abrasive cloth. TROUBLESHOOTING 1) The light does not come on at all:

a) Make sure the wall switch and circuit breaker are on. b) Make sure the wiring is correct. c) Make sure the Daylight turn-on(photocell) is in effect. d) Make sure the motion sensor is aimed in the right direction to cover the desired area. e) Make sure the outside air temperature is not close to the same as a persons body heat. 2) The light comes on during the day. a) Make sure the motion sensor is not installed in a relatively dark location. If unable to fix any of the above issues, please consult a certified electrician. R FIVE-YEAR LIMITED WARRANTY: If, during normal use, this PATRIOT LIGHTING lighting fixture breaks or fails duet to a defect in material workmanship within five (5) years from the date of original purchase, simply bring this lighting fixture with the original sales receipt back to your nearest MENARDS retail store. At its discretion, PATRIOT LIGHTING agrees to have the product or any defective part(s) repaired or replaced with the same or similar PATRIOT LIGHTING product or part free of charge, within the stated warranty period, when returned by the original purchaser with original sales receipt. This warranty; (1) excludes expendable parts including but not limited to light bulbs; (2) does not cover damage that has resulted from abuse or misuse; and (3) does not cover any losses, labor, injuries to persons/property or costs. This warranty does give you specific legal rights and you may have other rights, which vary from state to state. FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. R R R This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device must be installed and operated with a minimum distance of 20 cm between the radiator and user body. Questions, problems, missing parts?

Before returning to your retailer, call our customer service at 1-800-887-6326 Monday Friday 9:00 a.m. 5:00 p.m. CST Page 17 of 16 190717