FCC ID: 2AUZI-819628B Sekstant Gateway

Sekstant Gateway Installation Instructions Installation Instructions - Sekstant Gateway V1.3 | Page 2 1. Preface This document is dated November 2021, edited by Maersk Container Industry AS. All rights reserved. The information herein is subject to change without notice and does not represent a commitment on any part of Maersk Container Industry AS. While the information herein is assumed to be accurate, Maersk Container Industry assumes no responsibility for any errors or omissions that may appear in this documentation. 2. Introduction This document contains the installation instructions for the Sekstant gateway, its wiring and connections onto a Star Cool reefer with a CIM 6 controller. The Sekstant gateway should be mounted on the communication plate of the reefer. If this is not possible, please also refer to the additional instructions for mounting on the controller cabinet door. 3. Contents 1. Preface ..................................................................................................................................................... 2 2. Introduction ........................................................................................................................................... 2 3. Contents .................................................................................................................................................. 2 4. Safety ...................................................................................................................................................... 3 5. Tools Required .................................................................................................................. ................... 3 6. Complete Kit Contents ....................................................................................................................... 3 7. Instructions For Installing The Sekstant Gateway ...................................................................... 4 8. Additional Instructions For Mounting On The Controller Cabinet Door ..............................11 9. Additional Instructions For Units With Soldered On/Off Switch Connections .................. 12 10. Connections Overview ................... ................................................................................................. 13 11. Gateway LED Overview ..................................................................................................................... 13 Installation Instructions - Sekstant Gateway V1.3 | Page 3 4. Safety Before starting the Sekstant gateway installation, ensure correct personal protective equipment is worn and the unit is powered off and unplugged with the power cable and plug stored in the cable compartment. 5. Tools Required Drilling machine Cone drill, 26 mm Socket wrench, 10 mm Screwdriver, PZ2 Wire cutter Tape measure and pen 6. Complete Kit Contents Item no. 1 2 3 4 5 6 7 8 Item name Sekstant gateway Battery pack Securing nuts (2 pcs) Cable gland Screw set, ground rail Gromet plug Terminal block Cable ties (10 pcs) 1 4 6 2 8 3 7 5 Installation Instructions - Sekstant Gateway V1.3 | Page 4 7. Instructions For Installing The Sekstant Gateway The Sekstant gateway should be mounted on the communication plate. For SCI this is to the right of the controller cabinet and for SCU it is to the left of the condenser fan. 1. Power on the unit. 2. Update the controller software to the latest version, or minimum 356_04. 3. Ensure that the container ID in the controller is correct. 4. Turn the unit off and disconnect AC power. Open the controller cabinet and disconnect any modems no longer required. Both power and communication connections. 5. Mount the battery pack (item 2) in the preferred bay with the 2 securing nuts (item 3). If another device is mounted there then it is possible to mount the battery pack in the next bay to the left, directly next to the controller. 6. Remove the controller battery pack connector from the controller terminal X3. Important! Mount the green connector from the Sekstant battery pack (item instead. The controller battery pack can be 2) removed entirely, or left in its place, but must not be connected to anything. into controller terminal X3 7. Remove the 3 black plugs on the communication plate and use a cone drill size n-26 mm to make the center hole larger. If the unit is not fitted with a communication plate, see Section 8. Installation Instructions - Sekstant Gateway V1.3 | Page 5 8. Clean the communication plate with a clean cloth so it is free from oil and dirt. 9. Dismount the communication plate and remove the grey plug. On SCU, the grey plug is located at the top of the left side of the controller cabinet and can be reached from behind the condenser fan. 10. Dismantle the cable gland (item 4). Installation Instructions - Sekstant Gateway V1.3 | Page 6 11. Mount the cable gland base and the nut inside the cabinet. Tighten by hand. 12. Dismount the nut from the back of the gateway (item 1) and remove from the cable. 13. Remove the film from the top and bottom sticky foam pads on the gateway (item 1). Installation Instructions - Sekstant Gateway V1.3 | Page 7 14. Pass the cable through the center hole of the communication plate. 15. Mount the gateway (item 1) onto the plate in the correct orientation. 16. Pass the cable back through the nut and screw it tight onto the gateway (item 1) using 5 Nm. 17. Pass the cable through the cable gland nut. 18. Pass the cable through the cable gland base and into the controller cabinet. 19. Disconnect the bottom red connector (closest to the door) from the backside of the on/off switch. If this is not possible, see Section 9. 20. Connect the brown wire from the gateway (item 1) to the red wire from the battery pack (item 2). Mount the connection onto the bottom red connector (closest to the door) with the brown wire on top. 21. Remove the obsolete connector from the controller terminal X9 and mount the green connector from the gateway (item 1) in its place. Installation Instructions - Sekstant Gateway V1.3 | Page 8 22. Put the screw and washers together (item 5). Mount the screw set loosely onto the free space on the ground rail in the bottom of the controller cabinet. Mount the blue wire from the gateway (item 1) between the 2 washers in the same direction as the other wires and tighten the screw. 23. Ensuring the connectors are rotated correctly, connect the red and black wires from the gateway (item 1) to the battery (item 2). 24. Pull any excess cable length into the space behind the communication plate ensuring to leave at least 15 cm of cable length inside the controller cabinet. Installation Instructions - Sekstant Gateway V1.3 | Page 9 25. Ensure that the 3 PMM wires are tight against the top of the battery pack and that the current cable tie is positioned just above the heat shrink. Secure the 3 PMM wires to the blue wires just below K4 with a plastic cable tie (item 8). 26. The remaining unconnected three wire plug must be secured together with the battery wires next to K3. 27. Secure all wires with plastic cable ties (item 8). Wires should be folded as few times as possible with the battery connector easily accessable. Installation Instructions - Sekstant Gateway V1.3 | Page 10 28. Mount the cable gland gasket onto the cable and push it into the cable gland (item 4). Then pass the nut along the cable and screw it onto the cable gland by hand. 29. Ensure that any additional cable length is placed in the compartment behind the communication plate before mounting it. For SCU, ensure the cable is secured with plastic cable ties (item 8) behind the condenser fan and that any additional cable length is placed behind the controller. 30. Before applying AC power, ensure that the LED on the gateway (item 1) is on (flashing or solid). This is to ensure the battery is operating correctly. 31. Plug in the unit and turn on the power. The sequence of the LED on the gateway

(item 1) is: flashing green, solid red, flashing green, and finally solid green. This can take up to approx. 30 mins. Installation Instructions - Sekstant Gateway V1.3 | Page 11 32. If no power supply is available, wait until the LED on the gateway (item 1) is solid red

(within approx. 5 mins) before waking up the controller in battery mode by pressing on the user panel. 33. When the LED on the gateway (item 1) is solid green, the setup process has been successfully completed. 34. After installation, it is recommended that the unit is connected to AC power for at least 48 hours to ensure the battery is sufficiently charged. 8. Additional Instructions For Mounting On The Controller Cabinet Door 1. Remove any device already mounted on the controller cabinet door and plug the hole with the gromet (item 6) to avoid water ingress. 2. With a tape measure and pen, measure 16 cm from the top of the controller cabinet door and 11.5 cm from the left side of the door. Mark the spot. For units with a separate sub controller, measure 16 cm from the top and 13 cm from the left side. 3. Using a cone drill size n-26 mm make a hole on the spot. 4. Mount the gateway (item 1) as you would on the communication plate. See Section 7. 5. Once wiring has been connected as in Section 7, secure the cable and wires with plastic cable ties (item 8) together with the user panel to controller cables. The additional cable length must then be rolled up and secured with plastic cable ties (item 8) inside the controller cabinet. 9. Additional Instructions For Units With Soldered On/Off Switch Connections 1. Locate the orange modem power connector, cut the red wire and remove the insolation. Installation Instructions - Sekstant Gateway V1.3 | Page 12 2. Cut off the spade connector of the brown wire from the gateway (item 1) and the piggy back connector of the red wire from the battery (item 2). Remove the insolation from both wires. 3. Insert all three wires into the terminal block (item 7). Secure the wires with plastic cable ties (item 8) together with the battery wires. 10. Connections Overview Installation Instructions - Sekstant Gateway V1.3 | Page 13 Not used Connect to X9 Connect to X3 Connect together Connect together then to on/off switch Ground rail 11. Gateway LED Overview Solid green Flashing green Solid orange Solid red Flashing red

Gateway is working fine and reporting Gateway is starting up Gateway is not able to connect Gateway has not yet finished the installation process Gateway has an error, check the installation and connections FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. To comply with RF exposure requirements, a minimum separation distance of 20cm must be maintained between the users body and the device, including the antenna. IC STATEMENT This device complies with Industry Canada licence-exempt RSS standard(s) Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with RF exposure requirements, a minimum separation distance of 20cm must be maintained between the users body and the device, including the antenna. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. Ce dispositif est conforme aux normes autoriser-exemptes du Canada RSS d'industrie L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.Cet quipement est conforme avec l'exposition aux radiations IC dfinies pour un environnement non contrl. L'utilisateur final doit respecter les instructions de fonctionnement spcifiques pour satisfaire la conformit aux expositions RF. Cet metteur ne doit pas tre co-localises ou oprant en conjonction avec une autre antenne ou transmetteur. Afin de se conformer aux exigences d'exposition aux RF, une distance minimale de 20 cm doit tre maintenue entre le corps de l'utilisateur et le tlphone, y compris l'antenne.

AS 2AUZI-819628B

-819628B CAN ICES-3 (B)/NMB-3(B) Model No:Serial number: Manufacturer: MCI Item No.:Date of Manufacture:Made in:Sekstant Gateway V1.3P03784ID170W1935Maersk Container Industry818141B09/2019ChinaFCC ID:Contains FCC ID:IC: Contains IC:QIPPLS63-W255687830A-PLS63W

MAERSK Mlle CONTAINER INDUSTRY Maersk Container Industry A/S Postal address:

Bjerndrupvej 47 6360 Tinglev Danmark Phone +45 73 64 3400 Equipment Authorisation Division Federal Communications Commission www.mcicontainers.com 7345 Oakland Mills Road Reg.no. 13 82 37 74 Columbia, MD 21046 Date 10 February 2023 Page L/1 Request for Confidentiality Date: 10 February 2023 Morten Head of Design & Maintenance Maersk iner Industry AS Telephone: +45 73643400 FCC ID: 2AUZI-819628B Product Name: Sekstant Gatewa Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Schematics Block diagram Operation description Tune up BOM

MAERSK Nylykke ai CONTAINER INDUSTRY Maersk Container Industry A/S Postal address:

Bjerndrupvej 47 6360 Tinglev Danmark Phone +45 73 64 34 00 Federal Communications Commission Authorization & Evaluation Division www.meicontainers.com 7345 Oakland Mills Road Reg.no. 13 82 37 74 Columbia, Maryland 21046 USA Date 10 February 2023 Page 1/2 Attn.: Receiving Engineer Date: 10 February 2023 Morten Head of Design & Maintenance Maersk ner Industry AS FCC ID: 2AUZI-819628B Maersk Container Industry AS certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List (see Appendix A), the applicant should include an explanation on why the equipment is not covered equipment. Maersk Container Industry AS certifies that, as of the date of the filing of the application, the applicant identified on the Covered List as an entity producing covered equipment. Ke MAERSK dus Sy Huawei Technologies ideo surveillanys and ievar one equermest pro Hytera Communications Corporation. 10 ve essere (at tee puree curity ptiysical eer rsatnor sect utpsees, isu ever idea ceiver saree Hangthou Hikvision Digital Technology Compamy, 0 usposteal subi suey security 0 typical wet dy 9 quiero surveillance ane eteccerersere abe lDahuw Technalegy Company. li ihe purpose ul pubes safety secuti ny aurea of 6 sours moxie inet civ international USA tne uty act cf 1934 Tetetcrretiutintiet set Americas} Corp. sutyecs\p section 2 of 1933, ite stirs selec cre Unicom (Americas) Operations Limited el tie Core wmnurieiatie The inwusicr of sradkices or pryatlies of equipitienit or services idernifled on ti listshould *

cana alfa of such entities, soipiret ce services on Ue ulettilied by cot atesety soul be:

ction ip sections UIC Seryeces Capable oT ie farepont td) USCS ch CONTAINER INDUSTRY Appendix A - Covered List

(Updale Serer oer 2 nea

+ 4 iT Ca ata iat WL SEP CRS LNT th er

Maersk Container Industry AS U.S. Agent Designation for Service of Process -

Certification Attestation Letter 2/8/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2AUZI-819628B Per section 2.911(d)(7) of the FCC rules, Maersk Container Industry AS (the applicant) certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process:

Company Name: Global Product Services and Consultation LLC FCC Registration Number (FRN): 0033406703 Physical U.S. Company Address: 328 W Palm Ave. Monrovia, CA91016 Contact Person: Michael Chan Agent Email Address: cschanm@gmail.com The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed:

Agent Signed (if different from Applicant):

Signed:

Printed name: Morten Nylykke Title: Manager Company Name: Maersk Container Industry AS Signed:

Printed name: Michael Chan Title: Technical Director Company Name: Global Product Services and Consultation LLC Date: 2/8/2023 Date: 2/16/2023

* the applicant must designate a contact located in the United States for purposes of acting as the applicants agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process.