FCC ID: 2ADHK79V24 EV79V24A

EV79V24A Regulatory Compliance Information Revision 0.3 Oct 2023 Preliminary 1 Revision 0.3 (10/2023) This document contains the Regulatory Compliance information which will be part of the EV79V24A (ATA5293-XPRO) datasheet and related documents shared with customers. Preliminary 2 Revision 0.3 (10/2023) 1.0 Usage Instructions This equipment (EV79V24A/ATA5293-XPRO) is an evaluation board of the ATAK51005-V1 kit. It is not directly marketed or sold to the general public through retail; it is only sold through authorized distributors or through Microchip. Using this equipment requires a signif icant engineering expertise towards understanding of the tools and relevant technology, which can be expected only f rom a person who is professionally trained in the technology. The user must comply with all the instructions provided by the Grantee, which indicate installation and/or operating conditions necessary f or compliance. 2.0 Antenna Considerations The f ollowing table provides details about the approved antenna. Manufacturer Part Number KGEA-BFCR-B-0500J 3.0 Regulatory Approval This equipment has received regulatory approval f or the f ollowing countries:

Antenna type Middle Range Emitter Premo United States/FCC ID: 2ADHK79V24 Canada/ISED:

IC ID: 20266-79V24 o o HVIN: EV79V24A European Union/CE 3.1.0 United States This equipment has been approved f or use in the United States under Federal Communications Commission (FCC) CFR47 Telecommunications, Part 15 Subpart C Intentional Radiators. 3.1.1 Labeling and User Information The FCC ID label has been permanently affixed to equipment on the bottom silkscreen layer of the board and is visible, as well as, legible to the user. Due to the size of the equipment, the f ollowing compliance statements are included in the user manual:

This device complies with part 15 of the FCC Rules. Operation is subject to the f ollowing two conditions:

(1) This device may not cause harmf ul interf erence, and

(2) this device must accept any interf erence received, including interf erence that may cause undesired operation. NOTE: This equipment has been tested and f ound to comply with the limits f or a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmf ul interf erence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmf ul interf erence to radio communications. However, there is no guarantee that interf erence will not occur in a particular installation. If this equipment does cause harmf ul interf erence to radio or television reception, which can be determined by turning the equipment of f and on, the user is encouraged to try to correct the interf erence by one or more of the f ollowing measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Preliminary 3 Revision 0.3 (10/2023) Connect the equipment into an outlet on a circuit dif f erent f rom that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician f or help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and a human body. FCC NOTICE: This kit is designed to allow:

(1) Product developers to evaluate electronic components, circuitry, or software associated with the kit to determine whether to incorporate such items in a f inished product and

(2) Sof tware developers to write sof tware applications f or use with the end product. This kit is not a f inished product and when assembled may not be resold or otherwise marketed unless all required FCC equipment authorizations are f irst obtained. Operation is subject to the condition that this product not cause harmful interference to licensed radio stations and that this product accept harmful interf erence. Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter. The kit is labeled with the f ollowing legend: For evaluation only; not FCC approved f or resale;

3.1.2 Approved Antenna Types To maintain compliance in the United States, only the antenna type that has been tested shall be used. Testing of this equipment was perf ormed with the antenna type listed in the Antenna Considerations section above. 3.1.3 Helpful Websites Federal Communications Commission (FCC):

https://www.f cc.gov/

FCC Of f ice of Engineering and Technology (OET) Laboratory Division Knowledge Database

(KDB):

https://apps.f cc.gov/oetcf /kdb/index.cf m. 3.2.0 Canada This equipment has been approved f or use in Canada under Innovation, Science and Economic Development Canada (ISED, formerly Industry Canada) Radio Standards Specif ication (RSS) RSS-

210. 3.2.1 Labeling and User Information The ISED ID label has been permanently affixed to the equipment on the bottom silkscreen layer of the board and is visible, as well as, legible to the user. Due to the size of the equipment, the following compliance statement is included in the user manual:

Preliminary 4 Revision 0.3 (10/2023) This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the f ollowing two conditions:

(1) this device may not cause interf erence,

(2) this device must accept any interf erence, including interf erence that may cause undesired operation of the device. Lmetteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) Lappareil ne doit pas produire de brouillage;

(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le f onctionnement. 3.2.2 Approved Antenna Types To maintain compliance in Canada, only the antenna type that has been tested shall be used. Testing of this equipment was performed with the antenna type listed in the Antenna Considerations section above. 3.2.3 Helpful Websites Industry Canada:

http://www.ic.gc.ca/

3.3.0 European Union This equipment has been assessed f or use in European Union (EU) countries under the Radio Equipment Directive (RED) 2014/53/EU, European Telecommunications Standards Institute (ETSI) EN 300 330, and EN 62368-1. 3.3.1 Labeling Information The CE mark has been permanently affixed to equipment on the bottom silkscreen layer of the board and is visible, as well as, legible to the user. 3.3.2 Approved Antenna Types To maintain compliance in the EU, only the antenna type that has been tested shall be used. Testing of this equipment was performed with the antenna type listed in the Antenna Considerations section above. 3.3.3 Simplified EU Declaration of Conformity Hereby, Microchip Technology Inc. declares that the radio equipment type EV79V24A is in compliance with Directive 2014/53/EU. The f ull text of the EU declaration of conf o rmity f or this product is available at www.microchip.com/design-centers/wireless-connectivity/. 3.3.4 Helpful Websites Preliminary 5 Revision 0.3 (10/2023) A document that can be used as a starting point in understanding the use of Short-Range Devices

(SRD) in the EU is the European Radio Communications Committee (ERC) Recommendation 70-03 E, which can be downloaded f rom the European Communications Committee (ECC) at:

https://docdb.cept.org/. Additional helpf ul websites are:

Radio Equipment Directive (2014/53/EU):

https://ec.europa.eu/growth/single-market/european-standards/harmonised-standards/red_en European Conf erence of Postal and Telecommunications Administrations (CEPT):

http://www.cept.org European Telecommunications Standards Institute (ETSI):

http://www.etsi.org The Radio Equipment Directive Compliance Association (REDCA):

http://www.redca.eu/

Preliminary 6 Revision 0.3 (10/2023)

EV79V24A Label and Label Location Revision 0.1 Jun 2023 Preliminary 1 Revision 0.1 (06/2023) This document contains the Label and Label Location information for the EV79V24A (ATA5293-XPRO). Preliminary 2 Revision 0.1 (06/2023) Label is af f ixed to the top silkscreen layer of the board and is located as shown in the f ollowing:

Model Number / HVIN Preliminary 3 Revision 0.1 (06/2023) Preliminary 4 Revision 0.1 (06/2023)

Antenna Declaration Federal Communications Commission /

Innovation, Science and Economic Development Canada RE:

Antenna Declaration EV79V24A (Model: ATA5293-XPRO) FCC ID: 2ADHK79V24, IC: 20266-79V24 It's hereby declared that the model, ATA5293-XPRO, is only testing radiated and is accounted for as a result of the measurement such as field strength measurements on a part 15.249 or 15.231 device. So the gain does not necessarily need to be verified. However, enough information regarding the construction of the antenna shall be provided . The model ATA5293-XPRO is only radiated measurements are used to show compliance with limits for fundamental and spurious emissions. Antenna Brand name: PREMO Antenna Model name: KGEA-BFCR-B-0500J Antenna Type: Middle Range Emitter Antenna Antenna Frequency Range: 125kHz Sincerely yours, Applicant Signature Printed Name: HRUSHIKESH VASUKI Title: Vice President, Business Unit General Manager, WSG Address: 2355 West Chandler Blvd. Chandler, Arizona 85224-6199, United States Tel.: 1 480-437-0762 Email: rishi.vasuki@microchip.com

Certification Designating Applicant as FCC US Agent To: Federal Communications Commission Date: 07-24-2023 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Attestation Statement Part 2.911(d)(7) filing FCC ID: 2ADHK79V24 Microchip Technology Inc. (the applicant) as required by section 2.911(d)(7), will also serve as the agent for service of process for the above referenced FCC ID. The applicant acknowledge the applicants consent and the designated agent for service of processs obligation to accept service of process. The applicant acknowledge the applicants acceptance to maintain an agent for service of process for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledge the responsibility to inform the FCC whenever the agent information changes. Designated U.S. Agent from Applicant Company Company Name: Microchip Technology Inc. Contact Person: HRUSHIKESH VASUKI Address: 2355 West Chandler Blvd. Chandler, Arizona, USA 85224-6199 Tel.: 1 480-437-0762 Email: rishi.vasuki@microchip.com FCC FRN: 0001596279 Sincerely yours, Signature Printed Name: HRUSHIKESH VASUKI Title: Vice President, Business Unit General Manager, Wireless Solutions Group

Date: 2023-07-24 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road, Columbia, MD 21046, USA Subject: Confidentiality Request for FCC ID: 2ADHK79V24 Pursuant to FCC 47 CRF 0.457(d), the applicant requests that a part of the subject FCC/IC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent n/a Permanent Permanent Permanent Permanent Permanent Permanent Permanent Exhibit Block Diagrams External Photo Internal Photos ***

Operation Description/Theory of Operation Schematics Test Setup***

Tune-Up Procedure Users Manual***

Part List/ Antenna Construction Microchip Technology Inc. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public.

(*** Exceptional case for Permanent Confidentiality for these Exhibits by PAG only) Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely, By:

(Signature)

(Print name/Title) _HRUSHIKESH VASUKI / Vice President, Business Unit General Manager, WSG Tel: 1 480-437-0762 Email: rishi.vasuki@microchip.com MS-0044715 Page 1 of 1 Revision 1

Attestation Statements Not Covered Entity Applicant To: Federal Communications Commission Date: 07-24-2023 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(ii) filing FCC ID: 2ADHK79V24

[Microchip Technology Inc.] (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely yours, Applicant Signature Printed Name: HRUSHIKESH VASUKI Title: Vice President, Business Unit General Manager, Wireless Solutions Group Address: 2355 West Chandler Blvd. Chandler, Arizona, USA 85224-6199 Tel.: 1 480-437-0762 Email: rishi.vasuki@microchip.com

Attestation Statements Not Covered Equipment To: Federal Communications Commission Date: 07-24-2023 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(i) filing FCC ID: 2ADHK79V24

[Microchip Technology Inc.] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely yours, Applicant Signature Printed Name: HRUSHIKESH VASUKI Title: Vice President, Business Unit General Manager, Wireless Solutions Group Address: 2355 West Chandler Blvd. Chandler, Arizona, USA 85224-6199 Tel.: 1 480-437-0762 Email: rishi.vasuki@microchip.com