submitted | available | document details (if available) | source link |
---|---|---|---|
August 04 2013 | September 04 2013 |
various | manual pt 2 | Users Manual | 282.42 KiB | August 04 2013 / September 04 2013 |
Cube Card Reader 190 Nedap Mifare readers Install manual GENERAL The Cube card reader 190 series is capable of reading Mifare and DESFire credentials due to its dual reader technology. The Cube card reader 190 is designed to be used on door pillars (mullion) and suitable for outside and inside use. A model with keypad is also available. Functionality and output is determined by the configuration of the Cube card reader. The configuration is defined using the programm AEmon, and deployed via AEmon. Three LEDs (red, green, blue) and beeper are included. LEDs around the keypad ciphers light up only in case a PIN code is requested. The pigtail cable can be lead directly backwards. DIMENSIONS Dimensions: 7.52 x 2 x 1.2 in. 4 mounting holes available at 1.26 x 6.1in Cable pigtail: 10 x 26AWG shielded, 10 ft Optional spacer (max thickness 0.4 in) is available for other cable outlet (top or bottom) 10 x 26AWG Shield
. 5 4 1 4 x 5 5 5 1 0 4 5 7 12 1 9 1 1 50 32 30 Note: drawing dimensions are in mm MOUNTING PROCEDURE 190 For mounting the Cube card reader 190, the mounting plate must be placed on the wall first. For removing the mounting plate from the Cube card reader 190, unscrew the screw (1) (Torx, M5) at the bottom of the Cube card reader 190 and push the Cube card reader 190 slightly up (2). The plate can be mounted using the 4 holes. Place the cable to the correct position and replace the Cube card reader 190. 2 Push up 1 Un screw Mounting plate Date: 08 April 2013 This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys no licence under any patent or other right, nor does the publisher assume liability for any consequence of its use; specifications and availability of goods mentioned in it are subject to change without Version: B Part.no.: 9209735 Cube card reader 190 Wire Colour Function Power in (12-30VDC) 1 2 3 4 5 6 7 8 9 10 11 Power Ground RS485 A (-) RS485 B (+) Red Black Grey Violet Green White Yellow CONNECTIONS Cube card reader 190 is not hot-swappable, so when making or changing connections, power must be switched Off. Remark:
Cable shield (wire 11) must be connected to the metal case of the external device LED INDICATORS INSIDE / BACKSIDE There are two LEDs available: Blue for Status (of application), Green for Identification (both visible behind the SAM cover at the back side) EM shield (connected to power ground) Pink Blue Brown Reserved for future use Do not connect Shield / Metal SAM cover ST: STATUS (blue) Slow blinking Fast blinking 2 short flashes 3 short flashes Application running (operating) Downloading or error during loading Application present but not active No application present ID (green) Blinking Card detected Cube card reader 190 LED INDICATORS FRONT At the front a three colour LED is positioned at the middle of the Cube card reader 190 Depending of the used configuration the function of these LEDs can differ:
Green LED: Card is been authorised (UL led) Red LED:
Blue LED:
Card is not authorised (NA led), controller is stand-by Blinks fast:
Continuously ON: Determined by configuration: E.g. Reader stand-by. No configuration is available at this Cube card reader
(load Configuration first). Remark: Function of LEDs and Beeper is controlled by used application settings of Cube card reader.
(Blue LED is activated if UL is OFF and NA is more than 1 sec OFF) FIRMWARE Pay attention that the firmware loaded in the Cube card reader 190 together with the Cube card reader 190 type and configuration determines functionality and protocols. Remark: The Cube card reader 190 requires dedicated firmware (not identical to the Cube card reader MK170 firmware) SYSTEM CONFIGURATIONS (how to connect Cube card reader 190) To CUBE Core or CUBE Access Plus with RS485 special encrypted protocol.
(LEDs, Beeper and Keys are controlled over the RS485 communication) Cube card reader 190 FCC and IC CERTIFICATIONS This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Cet appareil se conforme aux normes RSS 210 exempts de license du Industry Canada. L'opration est soumis aux deux conditions suivantes:
(1) cet appareil ne doit causer aucune interfrence, et
(2) cet appareil doit accepter n'importe quelle interfrence, y inclus interfrence qui peut causer une opration non pas voulu de cet appareil. Les changements ou modifications nayant pas t expressment approuvs par la partie responsable de la conformit peuvent faire perdre lutilisateur lautorisation de faire fonctionner le matriel. 9205543 CUBE card reader M190 9205527 CUBE card reader MK190 SPECIFICATIONS Cube card reader 190 :
Product number:
Dimensions:
Protection:
Power Supply:
Environment:
Communication:
Indicators:
Antennas (internal): 13.56 MHz, Mifare compatible R&TTE:
7.52 x 2 x 1.2 in IP65 12VDC 30VDC Temperature: Operating and Storage: -31F to +150F Relative humidity: 10 93% non condensing RS485 (Encrypted AEOS protocol to AP4x03, (firmware APx003rs485NR). UL (green) NA (red) ,MD (blue) Weight: 0.78 lb M190:
MK190:
Power consumption:
Detection distance Mifare card: 1.5 in Hereby, Nedap N.V., declares that these products comply with the essential requirements and provisions of the Directive 1999/5/EC of the European Parliament and of the council of March 9, 1999 on Radio equipment and Telecommunications Terminal Equipment and the mutual recognition of their conformity and with the provisions of Annex IV (Conformity Assessment procedure referred to in article 10). 60mA@12VDC, 35mA@24VDC 90mA@12VDC, 45mA@24VDC CABLE SPECIFICATIONS 10 wire shielded cable of approx. 10 ft length included (pig tail). Extensions can be made:
RS485:
Power:
22AWG twisted pairs, shielded, max cable length: 3280 ft, cable capacity <= 33pF/ft. 22AWG twisted pairs, shielded, max cable length: 160 ft. MORE INFORMATION: For more detailed information contact your local Nedap supplier or check the internet site.
This product uses the FCC Data API but is not endorsed or certified by the FCC