submitted | available | document details (if available) | source link |
---|---|---|---|
Adobe PDF Library 15.0 |
various | Manual UHF portion | Users Manual | 3.23 MiB |
Lumen iL33 ADD-ON T325R RFID UPGRADE 2x | bracket 1x | antenna 1 1x | antenna 2 1x | cover A 1x | cover B 1x | reader RFID 1x | heatsink 10x | screw M3x6 4x | screw M3x8 2x | screw M4x25 4x | screw M3x12 2x | nylon washer 2x | tie-wrap 2x | cable tray 4x | double sided tape 2x | tape for covers 2x | foam tape 2x | label 38x19 1x | switch cable 1x | sync cable 1x | flat cable 1x | USB cable + core 1x | coaxial cable (short) 1x | coaxial cable (long) 2x | connector RJ45 2x | filter 1x | RFID coaxial cable 2x | degreaser
(3.5m / 11ft) label free zone
> 100 cm (3.3 ft)
> 100 cm (3.3 ft) Quick reference : ADD-ON T325R RFID UPGRADE N.V. Nederlandsche Apparatenfabriek Nedap Parallelweg 2, NL-7141 DC Groenlo (The Netherlands) Mail: support-retail@nedap.com dsgn date item
: CvdB
: 28 August 2018 11:20 AM
: 9986847 Copyright by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this drawing may be reproduced or distributed in any form or by any means, or stored in a data base or retrieval system without the prior written permission of NEDAP. document revision
: T986847-45.01
: A.01 remove covers 1 Screw M3x10 (4x) mount the brackets 1 1 1 2 3 4 Renos side (important) Bracket (2x) Nylon washer (2x) Screw M4x25 (2x) mounting antenna 1 contact-side 2 5 1 2 3 4 5 6 7 8 3 Coaxial cable (Short) - (You should hear Click) Coaxial cable (Long) - (You should hear Click) Switch cable Flat cable Fix with tie-wrap Renos side (important) Antenna 1 Screw M3x6 (4x) 4 1 6 2 3 4 1 7 8 mounting antenna 2 7 6 1 1 5 2 4 2 3 contact-side 1 2 3 4 5 6 7 Antenna 1 Flat cable Coaxial cable (Short) Coaxial cable (Short) - (You should hear Click) Renos side Antenna 2 Screw M3x6 (4x) mounting cable tray Clean surface. Place double-sided tape (2x 2 pcs) 3 1 2 3 4 5 6 Antenna 1 Antenna 2 Cable tray Coaxial cable (Long) Switch cable Foam tape (2x) 1 2 1 2 m m 8
~
4 5 1st - Switch cable 2nd - Coaxial cable 6 Both sides (clean surface before) Place covers (RFID) Remove paper layer 1 Clean surface inside before placing the cover. 4th 2 1st 3 2nd 2 1st 4 3rd 4th 5 Torque max. 0.3Nm make sure there are no visable cables 1 2 3 4 5 Place cable tray cover (Both sides) Tape black Cover A Cover B Screw M3x8 (Stainless steel) (4x) Place RFID Reader 1 2 1 2 3 4 Heatsink Screw M3x6 (2x) RFID Reader Screw M3x12 (4x) Mount switch and coaxial cable 1 2 3 Coaxial cable Switch cable USB cable + core 3 4 1 2 3 Fix with tie-wrap installation RX sensors 2 1 3 4 7 5 4 7 6 5 4 5 do not bend coaxial cable 4 1 2 3 4 5 6 7 Gate 1 Gate 2 RFID coaxial cable 11ft Filter Ethernet cable cat5e (not included) Connect to customer network USB cable + core place covers 1 1 1 Screw M3x10 (4x) replace label after installation 1 2 1 2 Pull to see the label information (Two labels at the front side and two at the back side) Replace label with the correct REGION and MODEL name. status LEDs RFID Reader 1 2 3 4 5 Blue Yellow Red Green Green On Blinking Off Blinking slow Off On Off On Blinking Off On Off The RFID Reader is connected to the Renos firmware The RFID Reader has received a command from the Renos firmware The RFID reader is not connected to the Renos firmware The firmware on the RFID Reader is running The firmware on the RFID reader is not running There is an error with the RFID output There is no error with the RFID output The RFID output is active The reader is reading RFID labels The RFID output is not active The RFID reader is powered by the Renos unit The RFID reader is not powered by the Renos unit 1 2 3 4 5 Disclaimer Nedap intends to make this manual accurate and complete. However, Nedap does not warrant that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. Nedap disclaims any liability for damage to property or personal injury resulting, in whole or in part, from improper installation, modification, use or misuse of its products. The information contained in this document is subject to change without notice. FCC and IC Compliance statement This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Cet appareil se conforme aux normes CNR 210 exempts de license du Industry Canada. Lopration est soumis aux deux conditions suivantes:
(1) cet appareil ne doit causer aucune interfrence, et
(2) cet appareil doit accepter nimporte quelle interfrence, y inclus interfrence qui peut causer une opration non pas voulu de cet appareil. Les changements ou modifications nayant pas t expressment approuvs par la partie responsable de la conformit peuvent faire perdre lutilisateur lautorisation de faire fonctionner le matriel. FCC and IC Radiation Exposure Statement This equipment complies with FCC and Canadian radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 5 cm between the radiator and a human body for normal operation. Personal standing permanently next to the antenna frame must keep a distance of at least 30 cm. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet quipement est conforme a CNR-102 limites nonces pour un environne- ment non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 5 cm entre le radiateur et un corps humain pour un fonctionnement normal. Les personnes se tenant en permanence ct du cadre de lantenne doivent respecter une distance minimale de 30 cm.. This Class B digital apparatus complies with Canadian ICES-003 Cet appareil numrique de Classe B est con-forme la norme Canadienne ICES-003. FCC Information to the user Note: This equipment has been tested and found to comply with the limits for a class B digital devices, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequent energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does not cause harmful interference to radio or television reception, which can be determine by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver. NOTE: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. To ensure compliance with FCC regulations, use only the shielded interface cables provided with the product, or additional specified components or accessories that can be used with the installation of the product. Declaration of Conformity Hereby, De N.V. Nederlandsche Apparatenfabriek Nedap declares that the radio equipment type ASSY T325R RF is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://portal.nedapretail.com/
User manual The complete instruction manual can be found at https://portal.nedapretail.com/
This product uses the FCC Data API but is not endorsed or certified by the FCC