VELOS5 Inductive Proximity Card Reader User manual

VP1004 ISO Reader Multiplexer Quick start The Velos VP1004 is a Velos component that is used to identify animals. The VP1004 must be installed in a V-box. A VP1004 is connected to the Velos CAN-bus and controlled by a VP8001 (VPU). Inputs / Outputs / Antennas

- 8 antennas, auto scanning one by one (max 10x VP1004 per VP8001)

- 2 outputs available to activate e.g. lights and 2 inputs for reading e.g. switches Power Supply VP2001 max 3m VP8001 To PC (LAN ethernet) VP1004 VP1004 Antenna 1-8 Antenna 17-24 VP1004 VP1004 Antenna 9-16 N e x t V P 1 0 0 4 N e x t V P 1 0 0 4 Antenna 25-32 FCC ID: CGDVELOS5 and IC: 1444A-VELOS5 Compliance statement (part15.19) This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Dclaration Conformit Cet appareil se conforme aux normes RSS210 exempts de license du Industry Canada. L'opration est soumis aux deux conditions suivantes:

(1) cet appareil ne doit causer aucune interfrence, et

(2) cet appareil doit accepter n'importe quelle interfrence, y inclus interfrence qui peut causer une opration non pas voulu de cet appareil. Warning (part15.21) Changes or modifications not expressly approved by party responsible for compliance could void the user s authority to operate the equipment. This in particular is applicable for the antenna which can be delivered with the VP4001 System. VP1004- ISO Reader Multiplexer - Quick start 9-2011 Doc.part.no. 5277434 45.01B 1/ 4 VP8001 (1) VP8001 (2) LAN VP1004 VP1004 Velos cable Lmax = 80m Max = 5x VP1004 Velos cable Lmax = 80m Max = 5x VP1004 VP1004 VP1004 Connections Velos cable OUT

(to next VP1004) r e d l b a c k l b u e r e d l b a c k l b u e l b u e w h i t e l b u e w h i t e Velos cable IN o r a n g e o r a n g e w h i t e o r a n g e o r a n g e w h i t e a n t e n n a Details VP1004 inputs and outputs Vin CAN SYNC I/O 1 .. 2 ANTENNA F SYNC

CH CL

O

I

FI/FO Input voltage 24 VDC, +20% -20%

Minus CAN high (cable twisted pair with CL) CAN low (cable twisted pair with CH) Shielding of CAN-bus cable Synchronisation (no plus or minus, cable must be twisted pair) See above Output max 400mA Output max 400mA / 1.7A input Minus for output (O) and minus input (I) Input Antenna (core) Antenna (shield of coax cable) Frequency synchronisation FI=in FO=out VP1004- ISO Reader Multiplexer - Quick start 9-2011 Doc.part.no. 5277434 45.01B 2/ 4 Details Velos cable Red (+) Black (-) Power 1,5 mm2 Part No. 7705310 Blue (Ch) Blue/white (Cl) Shield Communication 0,34 mm2 Twisted pair shielded Orange (Sync) Orange/white (Sync) Shield HF Synchronisation 0,34 mm2 Twisted pair shielded Antennas A VP1004 has an automatic tuning module. The status is shown with LED indicators. Only V-sense antennas types can be used. Not all types are compatible, check compatibility before use. Display menu display push button DISPLAY ADDRESS Shows the actual address SET ADDRESS Change the address ANTENNA POWER Min/max 10 / 99. Normally set to 99. Possible to set a lower value. ANTENNA SENSITIVITY SQUELCH Min/max 9 / 0. Normally set to 0. Possible to set a lower value. SIGNAL LEVEL FDX Shows signal level measured by the FDX receiver SIGNAL LEVEL HDX Shows signal level measured by the HDX receiver TEST IDENTIFICATION Shows last 2 digits of a tag number DISPLAY ERROR Shows error code TEST OUTPUT L1 L5 TEST INPUT I1 i5 SETTINGS TO DEFAULT All HF settings back to factory settings (enter 99) Press button until blinking Press button short To leave menu:

press button until display is empty VP1004- ISO Reader Multiplexer - Quick start 9-2011 Doc.part.no. 5277434 45.01B 3/ 4 LED indicators POWER STATUS Display V in V out LAST O1 .. O2 I1 .. I2 ID on off Green on off Blue Slow breathing Fast blinking Address indicated Green on off Orange Orange blinking Red Green on off Orange blinking Red blinking Green on off Orange blinking Red Red blinking Green on off Red blinking Green on off Green one by one Green on Red on Power on No power Operating ok Downloading or error during download No communication Communication status ok Input power applied No power Low power, lower then 20V Wrong CAN-bus connection, Vin and Vout swapped Error, plus and minus swapped Output power No power Low power Error, plus and minus swapped V-pack is last one on the CAN-bus V-pack is not last one on the CAN-bus CAN-bus error and last V-pack on CAN-bus CAN-bus error CAN-bus warning / wrong connected Output on Output off Output error / overload Input contact open Input contact closed Antenna ok Antenna ok and tag identified Antenna error / not connected / not tuned correctly Specifications VP 1004 Dimensions CAN Power Software Inputs Outputs Antennas Detection distance Synchronization Environment IP class 143 x 120 x 68 mm LxWxH (excluding mounting rail) Weight: 360 gr CAN-bus communication 125 kBit Input voltage 25 VDC, +20% -20%

Min power consumption 300 mA with antenna switched on Protected against reverse connection power supply Downloadable by the CAN network Reading inputs, analog (0-40V) and digital. Suitable for NPN and PNP sensors. Max. 0.4 Amp by current limiter, short-circuiting protected 800 H. Different types possible. Varies per antenna Synchronization according to ISO 11785 / 24631-6 Temperature: Operating: -10 55 C, Storage: -25 Relative humidity: 10 IP 30. When installed in V-box IP 65 (cover and cables installed correctly !) 93% non condensing 70 C Always use a NEDAP power supply. The Nedap guarantee-regulations are only valid when is installed as indicated in this manual. Install data cables at a safe distance from (high) powered cables For more detailed information contact your local Nedap supplier or check the internet site. This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys no licence under any patent or other right, nor does the publisher assume liability for any consequence of its use; specifications and availability of goods mentioned in it are subject to change without notice; it is not to be reproduced in any way, in whole or in part, without the written consent of the publisher. Nedap N.V., AGRI P.O. Box 104 NL-7140 AC GROENLO The Netherlands VP1004- ISO Reader Multiplexer - Quick start 9-2011 Doc.part.no. 5277434 45.01B 4/ 4