FCC ID: CGDLWBRDG Low power communication device

p/n 9986294 ENUS Language Luxon Bridge Installation guide 1. Before you start, check the package contents Luxon Bridge DIN-rail clips (2x) Blind plug for cable gland (2x) Installation guide Installation of electrical components must be completed by a certified electrician as per local codes and regulations. 2. Mounting 3. Wiring 1. Mount the Luxon Bridge to a wall or other flat mounting surface using pan-head screws, max 4.5mm diameter. 2. Alternatively, in case of DIN-rail mounting, click the DIN-rail clips into the rear of the Luxon Bridge. Connect the Luxon Bridge to mains power.

(100-347Vac 50/60Hz) Make sure the mains power source is not powered during installation. Connect the required sensor or switch to an I/O port. www.nedap-luxon.com 1. Open the wiring compartment after loosening the two screws on the front. 2. Enter the mains cable through the left wire gland. 3. Connect L and N wire to corresponding terminals, no earth connection required. 4. If applicable, connect the switched mains line to the Sensor input. 5. Enter the sensor and/or switch cable using the smaller two cable glands. 6. Connect the wires to the correct I/O terminals, see section 5 for details. 7. Mount the wiring compartment cover. 8. Unused cable glands can be closed using a blind plug. 4. Quick test Testing power supply and testing correct operation of connected sensor and/or switch. 1. Switch on the mains power 2. The green led (mounted internally) must light up 3. Trigger the sensor, the green led must flash three times 4. Operate the switch, the green led must flash three times. 5. If applicable, operate the mains switch, the green led must flash three times. 5. Overview of compatible sensors and switches and their connections For possible sensors see Luxon Portal: https://portal.nedap-luxon.com. Compatible sensors and switches Connection Signal wire Device Nedap motion sensor Commercial 24V motion sensor Light sensor Switch, low voltage Switch, mains voltage C1 C1 C1 C1 Sensor (ac sensor input, reference to mains N, max. 347Vac) 24V Supply wire

C2 C2 C2

0V wire 0V 0V 0V 0V

In case a second low voltage sensor or switch shall be connected, use C3 and C4 terminals. Report which sensor is connected to which I/O port, this information is required during commissioning. www.nedap-luxon.com FCC and ISED declarations 6. Compliance statement (part 15.19) This device complies with part 15 of the FCC Rules and to RSS of ISED. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Dclaration Conformit Cet appareil se conforme aux normes RSS exempts de license du ISED. Lopration est soumis aux deux conditions suivantes

(1) cet appareil ne doit causer aucune interfrence, et

(2) cet appareil doit accepter nimporte quelle interfrence, y inclus interfrence qui peut causer une opration non pas voulu de cet appareil. Warning (part 15.21) Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. RF Exposure (OET Bulletin 65) To comply with FCC RF exposure requirements for mobile transmitting devices, this transmitter should only be used or installed at locations where there is at least 20cm separation distance between the antenna and all persons. Disclaimer By using this manual you accept the terms of this disclaimer. Nedap has made every effort to ensure that this manual is accurate. Nedap accepts no liability for any inaccuracies or omissions in this manual nor for any damages arising from or related to its use. Information in this manual is subject to change without notice and does not represent any commitment on the part of Nedap. Nedap does not assume any obligation to update the information in this manual after publication and reserves the right to make improvements to this manual and/or to the products described in this manual at any time without notice. If you find information in this manual that is incorrect, misleading or incomplete, we would appreciate your comments and suggestions. Nedap disclaims all responsibility for any loss, injury, claim, liability or damage of any kind resulting from, arising out of or any way related to any errors in or omissions from this document and its content, including but not limited to technical inaccuracies and typographical errors. We do not vouch for the goods being fit for the use intended by the purchaser, not even if that use should have been mentioned to us, unless we have so committed ourselves in writing. Copyright 2020 by Nedap N.V. All rights reserved. No part of this document may be reproduced or distributed in any form or by any means, or stored in a database retrieval system without the prior express permission of the copyright holder. No part of this book may be reproduced by any means, nor transmitted, nor translated into a machine language without the written permission of the publisher. www.nedap-luxon.com

Label 1 Label 2 Label 3 Label 3 Label 1 Label 2 Rev:

Change description Dimensions: mm Scale:

ISO A GENERAL TOLERANCES According to ISO 2768-mK Roughness acc. ISO 1302 in m

Description:

23 product labels Luxon Bridge Copyright by NEDAP N.V.. No part of this document may be reproduced or distributed in any form or by any means, or stored in a database or retrieval system, without the prior written permission of NEDAP. Format: A4 By:

LHO Date:

15012020 9986294-23 1 check Page 1 of 1 Created:

Checked:

Accepted:

Item:

Document:

Doc. Revision:

Doc. Status:

Page: 1/1 of DocRef dated 10-01-2020

: CGDLWBRDG To whom it may concern, On behalf of our customer Nedap N.V. , we hereby would like to apply for an Original certification for the following device:

FCC ID IC : 1444A-LWBRDG Manufacturer : Nedap N.V. Brand Model HVIN : 9986294 Description The following PDF files (exhibits) are electronically submitted:

: Digital Transmission System (DTS)

: Nedap

: Luxon Bridge 1. Cover letter (this document) 2. Request or confidentiality 3. Authorization letter 4. Form 731 5. Antenna information 6. Bill of material (BOM)- Not required-Not provided 7. Block diagram 8. Circuit diagram 9. Interior photographs 10. Exterior photographs 11. Label information 12. Operational description 13. Test report in conformity with 47 CFR Part 15 / RSS-247 issue 2 14. Test setup photographs 15. User/installation manual 16. RF Exposure according 47 C.F.R. 1.1310 and 2.1091 and ISED RSP-100 Annex A,B and RSS-102 Annex C Best regards, TV Rheinland Nederland B.V. R .van der Meer Test Engineer TV Rheinland Nederland B.V. Eiberkamp 10 9351VT Leek The Netherlands Telephone: +31 888887888 Internet: www.tuv.com/nl E-mail: products@nl.tuv.com

. l a v o r p p a r o i r p s e r i u q e r n o i t a c i l p p a r o e s u y n A i

. s k r a m e d a r t d e r e t s g e r e r a V U T d n a V E U T

, V T

Nedap N.V. Parallelweg 2 7141 DC Groenlo The Netherlands January 08, 2020 Subject: Confidentiality Request for FCC ID: _CGDLWBRDG and IC: 1444A-LWBRDG Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC/IC application be held confidential. T: +31 (0)544 471 111 info@nedap.com www.nedap.com Type of Confidentiality Requested Short Term Permanent Short Term Short Term Permanent Permanent Exhibit Block Diagrams Operation Description/Theory of Operation Schematics Nedap N. V. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely, By:

_____________/ Compliance manager_

(Signature/Title) _Reinold Hubers_

(Print name) Trade register: 08013836 | IBAN: NL08 ABNA 0453299555 | BIC: ANBNANL2A | VAT: NL006456285B01 The General Terms and Conditions of ICT-Office apply to all our offers and agreements. These conditions can be found at our website and can be provided upon request.

July 26, 2019 Nedap N.V. Parallelweg 2 7141 DC Groenlo The Netherlands T: +31 (0)544 471 111 info@nedap.com www.nedap.com Authority to Act as Agent TUV Rheinland of North America, Inc. 1279 Quarry Ln., Ste. A Pleasanton, CA 94566 To Whom It May Concern:

I appoint Richard van der Meer of TV Rheinland Nederland B.V. to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canadas regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TV Rheinland Group, still resides with Nedap N.V. For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date:

By:

Title:

On behalf of:

_Compliance Manager________ Telephone:__+31 5440471111________________________ __________________________ __Reinold Hubers_________

(Print name) _ _Nedap N.V.___________ August 01, 2020

(Signature) Trade register: 08013836 | IBAN: NL08 ABNA 0453299555 | BIC: ANBNANL2A | VAT: NL006456285B01 The General Terms and Conditions of ICT-Office apply to all our offers and agreements. These conditions can be found at our website and can be provided upon request.