NEW POS TECHNOLOGY NEW9220 Smart POS Terminal PRODUCT MANUAL NEW POS Technology limited Precautions Do not use the non-dedicated power supply, because it may be in trouble due to the mismatch of power. Do not spill any liquid substance or take any conductive objects into the product, otherwise it will cause a short circuit and damage the product. Do not vibrate, shake or knock the product sharply. Do not plug in or pull out any external components or equipment in a charging state, it may cause damage to the internal circuitry. Cut off the power before turn off the machines power. Do not place the product in an elevated temperature, humid, dusty or strong electromagnetic field environment. When a fault occurs, immediately turn off the power supply and discontinue to use the product, please contact the service sector related to our company. Do not open and repair it by yourself. When the terminal being attacked by unscrupulous environment(such as opening the terminal shell, etc.), the internal sensitive information stored in the terminal will be erased. For avoiding unnecessary trouble, you should not open the housing. When the battery reaches the service life, it can not be thrown away, it should be disposed in compliance with local laws and regulations or instructions. Contents Checklist The following items should be found inside the box:
1. POS terminal 2. AC Power Supply 3. Li-ion Battery 4. Thermal paper roll 5. Product Manual 1PCS 1PCS 1PCS 1PCS 1PCS NEW POS TECHNOLOGY LIMITED NEW9220 www.newpostech.com NEW POS Technology limited NEW POS Technology limited Tag label 18 Flash 19 20 Base contacts Speaker Rubber pad Rear camera Battery cover Handle Antenna inductive zone Tear-off knife ON/OFF key Charge indicator Programable Leds Front camera indicator Magnetic stripe card 21 22 Micro USB port Headphone jack NEW9220 Figure 1 Paper holder Lid Front camera Volume key LCD User smart card slot NEW9220 www.newpostech.com NEW9220 www.newpostech.com www.newpostech.com NEW POS Technology limited NEW POS Technology limited Installation Guidance 1. Install the battery Open the battery cover of the device. Connect the cable of the battery to the right side battery connector on the machine and put the battery to its place. (Tag label on the battery upwards) Close the battery cover. NOTE: 1. Confirm the machine is turned off when you install or uninstall the SIM/UIM card, or your card will be damaged. 2. Do not paste any label on the SIM/SAM card to influence your card thickness, or it may result in loading or removing the card can not be carried out smoothly. Open the battery cover figure Install the battery figure NOTE: When removing the battery, please pick up the battery, then gently forced to unplug it to avoid damage to cables. 2. Install SIM/SAM card Open the battery cover and remove the battery. Keep the chip side on the SIM/SAM card downward and unfilled corner outward, insert the card to the bottom. Install the battery and then close the battery cover. 3. Power on/off the device Power on: press and hold the power key until the LCD display, then the machine will be turned on. Power off: press and hold the power key more than 2 seconds, then the screen will give you a tips, you just choose the shutdown key. Force shut down: Press the power key more than 8 seconds. 4. Install the printer paper Pull up the handle and open the paper holder Lid. Put the printer paper into paper holder Lid according to the direction of the graphic. Close the paper cover. Open the Paper holder Lid Install the printer paper Install SIM/SAM/TF card SAM TF SIM NOTE: 1. When install thermal paper, we need the side coated with thermal media facing the printer heating plate, or you can not print out the characters correctly. 2. Do not keep the printer paperless for long time, or it may cause the roller pasting with the plate. 3. The temperature is high on the heating plate, please do not touch it without cooling. 4. Tear-off knife edge is sharp, please be careful. Do not touch it for avoiding danger. NEW9220 www.newpostech.com NEW9220 www.newpostech.com NEW POS Technology limited NEW POS Technology limited Technical Specifications Project CPU Memory System Display MS Card Reader Smart Card Reader Contactless Card Reader Security Communications Satellite Positioning Camera Multimedia Printer Ports Buttons Card Slots Battery Power Dimensions Working Environment Storage Environment Certifications Optional Max RF power level Technical High Performance 4 Core Processor+Special secure CPU DRAM:1G, FLASH:8G; Supports Micro SD/TF Card, up to 32G Android 5.X 5.5 inch 720*1280 pixels capacitive touch screen with e-signature functionality Track 1/2/3,bi-directioanl,compliant with ISO7811,7812 Supports Memory Card, CPU Card, EMV4.3, PBOC3.0, ISO7816 Standard 13.56MHz. Supports Mifare Card,SONY Felica. Compliant with ISO/IEC14443 Type A&B MK/SK, DUKPT, FIXED.3DES, RSA, AES, SHA-256, SM2, SM3, Sm4. 4G/3G/2G, WiFi, Bluetooth. GPS, BEIDOU, GLONASS Front Camera:300 thousand pixel;
Rear Cemara:5-mega pixel, with auto flash and focus 720P video recording, 1080P video broadcast High-speed thermal printer, Paper roll width and diameter: 58mm/40mm 1*Micro USB OTG 1*Power switch, 2*Volume keys 1*SIM, 2*SAM, 1*TF Card 7.2V/2600mAh Input:100-240V AC, 50/60Hz; Output:5.0V DC, 2.0A 184mm*84mm*60mm(L*W*H) Temperature:0 ~ 50 (32~ 122). Humidity:10% ~ 90% (non-condense). Temperature: -20 ~ 60(-4~140). Humidity: 5% ~ 95% (non-condense). PCI PTS 5.X, EMV LEVEL 1&2, EMVContactless, CE, RoHS CUP, PBOC3.0, QPBOC3.0 Docking Station BLE(2402-2480MHz):-0.1dBm BT3.0(2402-2480MHz):5.4dBm Wifi(2412-2472MHz):15.49dBm Wifi(5.15-5.725MHz):14.61dBm GSM900: 30.91dBm/1800: 30.65dBm WCDMA B1: 22.00dBm/B8: 21.39dBm LTE B1: 21.49dBm/B3: 21.35dBm/B7: 21.72dBm/B8: 21.61dBm/
B20: 21.56dBm/B38: 22.18dBm/B40: 22.41dBm NFC Note:
1. Warranty valid for 12 months after purchasing date. 2. This warranty will be voided if the product is damaged due to natural disaster, fire, unauthorized alteration or improper usage. 3. Free Warranty covers original parts only 4. Warranty service will not be provided if no the dealer's stamp or this card is missing. The SAR limit of Europe is 2.0 W/kg. Device types Smart POS Terminal has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use worn on the body is 1.003 W/kg. This device was tested for typical body-worn operations with the back of the handset kept 0cm from the body. To maintain compliance with RF exposure requirements, use accessories that maintain a 0cm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with RF exposure requirements, and should be avoided. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Hereby, NEW POS TECHNOLOGY LIMITED declares that the radio equipment type (Smart POS Terminal, NEW9220) is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
http://www.newpostech.com/
Notice: This device may be used in each member state in EU The device is restricted to indoor use when operated in Belgium(BE), Bulgaria(BG), Czech Republic(CZ), Denmark(DK), Germany(DE), Estonia(EE), Ireland(IE), Greece(EL), Spain(ES), France(FR), Croatia(HR), Italy(IT), Cyprus(CY), Latvia(LV), Lithuania(LT), Luxembourg(LU), Hungary(HU), Malta(MT), Netherlands(NL), Austria(AT), Poland(PL), Portugal(PT), Romania(RO), Slovenia(SI), Slovakia(SK), Finland(FI), Sweden(SE), United Kingdom(UK), Turkey(TR), Norway(NO), Switzerland(CH), Iceland (IS) and Liechtenstein(LI) using frequency in 5150MHz~5350. NEW9220 www.newpostech.com NEW9220 www.newpostech.com 7 NEW POS Technology limited NEW POS Technology limited FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. in accordance with the Note: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help instructions, may cause harmful The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types Portable Smart POS Terminal (FCC ID: WAL9220) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification when properly worn on the body is 1.022W/kg. This device was tested for typical body-worn operations with the back of the handset kept 0cm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 0cm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. NEW9220 www.newpostech.com NEW POS TECHNOLOGY LIMITED Address: 14/A, Financial Technology Building, Financial & Technology Building, No.11, Keyuan Rd, Nanshan District, ShenZhen, China Tel: +86-755-86938425 Fax: +86-755-82790632 E-mail: Sales@newpostech.com Postalcode: 518057 WebSite: www.newpostech.com