FCC ID: 2ADZRG240WG 7368 ISAM ONT

7368 ISAM ONT G-240W-G Product Guide 7368 Intelligent Services Access Manager ONT 7368 ISAM ONT G-240W-G Product Guide 3FE-47555-AAAA-TCZZA Issue: 01 Nokia Proprietary and confidential Use pursuant to applicable agreements 7368 ISAM ONT G-240W-G Product Guide Nokia is a registered trademark of Nokia Corporation. Other products and company names mentioned herein may be trademarks or tradenames of their respective owners. The information presented is subject to change without notice. No responsibility is assumed for inaccuracies contained herein. 2018 Nokia. Contains proprietary/trade secret information which is the property of Nokia and must not be made available to, or copied or used by anyone outside Nokia without its written authorization. Not to be used or disclosed except in accordance with applicable agreements. 2 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Preface 1 Preface This preface provides general information about the documentation set for optical network terminals (ONTs). 1.1 Scope This documentation set provides information about safety, features and functionality, ordering, hardware installation and maintenance, and software installation procedures for the current release. 1.2 Audience This documentation set is intended for planners, administrators, operators, and maintenance personnel involved in installing, upgrading, or maintaining the ONTs. 1.3 Required knowledge The reader must be familiar with general telecommunications principles. 1.4 Acronyms and initialisms The expansions and optional descriptions of most acronyms and initialisms appear in the glossary. 1.5 Assistance and ordering phone numbers Nokia provides global technical support through regional call centers. Phone numbers for the regional call centers are available at the following URL:

http://support.alcatel-lucent.com. For ordering information, contact your Nokia sales representative. Issue: 01 3FE-47555-AAAA-TCZZA 3 Preface 7368 ISAM ONT G-240W-G Product Guide 1.6 Nokia quality processes Nokias ONT quality practices are in compliance with TL 9000 requirements. These requirements are documented in the Fixed Networks Quality Manual 3FQ-30146-6000-QRZZA. The quality practices adequately ensure that technical requirements and customer end-point requirements are met. The customer or its representatives may be allowed to perform on-site quality surveillance audits, as agreed upon during contract negotiations 1.7 Safety information For safety information, see the appropriate safety guidelines chapter. 1.8 Documents Documents are available using ALED or OLCS. Procedure 1 To download a ZIP file package of the customer documentation 1 2 3 4 5 6 Navigate to http://support.alcatel-lucent.com and enter your user name and password. If you are a new user and require access to this service, please contact your Nokia sales representative. From the Technical Content for drop-down menu, choose the product. Click on Downloads: Electronic Delivery. Choose Documentation from the drop-down menu and click Next. Select the image from the drop-down menu and click Next. Follow the on-screen directions to download the file. 4 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Preface Procedure 2 To access individual documents Individual PDFs of customer documents are also accessible through the Nokia Customer Support website. 1 2 3 4 Navigate to http://support.alcatel-lucent.com and enter your user name and password. If you are a new user and require access to this service, please contact your Nokia sales representative. From the Technical Content for drop-down menu, choose the product. Click on Manuals and Guides to display a list of customer documents by title and part number. You can filter this list using the Release drop-down menu. Click on the PDF to open or save the file. 1.9 Special information The following are examples of how special information is presented in this document. Danger Danger indicates that the described activity or situation may result in serious personal injury or death; for example, high voltage or electric shock hazards. Warning Warning indicates that the described activity or situation may, or will, cause equipment damage or serious performance problems. Caution Caution indicates that the described activity or situation may, or will, cause service interruption. Note A note provides information that is, or may be, of special interest. Issue: 01 3FE-47555-AAAA-TCZZA 5 Preface 7368 ISAM ONT G-240W-G Product Guide 1.9.1 Procedures with options or substeps When there are options in a procedure, they are identified by letters. When there are required substeps in a procedure, they are identified by roman numerals. Procedure 3 Example of options in a procedure At step 1, you can choose option a or b. At step 2, you must do what the step indicates. 1 This step offers two options. You must choose one of the following:

a b This is one option. This is another option. 2 You must perform this step. Procedure 4 Example of required substeps in a procedure At step 1, you must perform a series of substeps within a step. At step 2, you must do what the step indicates. 1 This step has a series of substeps that you must perform to complete the step. You must perform the following substeps:

i ii iii This is the first substep. This is the second substep. This is the third substep. 2 You must perform this step. 6 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Preface 1.10 Multiple PDF document search You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a common term. Adobe Reader displays the results in a single display panel. The results are grouped by PDF file, and you can expand the entry for each file. Note The PDF files in which you search must be in the same folder. Procedure 5 To search multiple PDF files for a common term 1 2 3 4 5 6 Open Adobe Acrobat Reader. Choose EditSearch from the Acrobat Reader main menu. The Search PDF panel appears. Enter the search criteria. Click on the All PDF Documents In radio button. Select the folder in which to search using the drop-down menu. Click on the Search button. Acrobat Reader displays the search results. You can expand the entries for each document by clicking on the + symbol. Issue: 01 3FE-47555-AAAA-TCZZA 7 Preface 7368 ISAM ONT G-240W-G Product Guide 8 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Table of contents 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.9.1 1.10 2 2.1 2.1.1 2.1.2 2.2 2.2.1 2.2.2 2.2.3 2.2.4 2.2.5 2.2.6 2.2.7 2.3 2.3.1 2.3.2 2.3.3 2.4 2.5 2.5.1 2.5.1.1 2.5.2 2.5.3 2.5.4 2.5.5 2.6 3 3.1 3.1.1 3.1.2 3.1.2.1 3.1.2.2 Preface.............................................................................................3 Scope ..........................................................................................................3 Audience......................................................................................................3 Required knowledge....................................................................................3 Acronyms and initialisms.............................................................................3 Assistance and ordering phone numbers....................................................3 Nokia quality processes...............................................................................4 Safety information........................................................................................4 Documents ..................................................................................................4 Special information......................................................................................5 Procedures with options or substeps...........................................................6 Multiple PDF document search ...................................................................7 ETSI ONT safety guidelines .........................................................17 Safety instructions .....................................................................................17 Safety instruction boxes ............................................................................17 Safety-related labels..................................................................................18 Safety standards compliance ....................................................................19 EMC, EMI, and ESD compliance...............................................................19 Equipment safety standard compliance.....................................................19 Environmental standard compliance .........................................................20 CE RED RF Radiation Exposure Statement .............................................20 Laser product standard compliance ..........................................................20 Resistibility requirements compliance .......................................................20 Acoustic noise emission standard compliance..........................................20 Electrical safety guidelines ........................................................................21 Power supplies ..........................................................................................21 Cabling ......................................................................................................21 Protective earth .........................................................................................21 ESD safety guidelines ...............................................................................22 Laser safety guidelines..............................................................................22 Laser classification ....................................................................................22 Laser warning labels..................................................................................22 Laser classification ....................................................................................24 Transmit optical output ..............................................................................25 Normal laser operation ..............................................................................25 Location class............................................................................................25 Environmental requirements......................................................................25 ETSI environmental and CRoHS guidelines...............................27 Environmental labels .................................................................................27 Overview....................................................................................................27 Environmental related labels .....................................................................27 Products below Maximum Concentration Value (MCV) label....................27 Products containing hazardous substances above Maximum Concentration Value (MCV) label..............................................................28 Issue: 01 3FE-47555-AAAA-TCZZA 9 7368 ISAM ONT G-240W-G Product Guide Hazardous Substances Table (HST).........................................................29 Other environmental requirements............................................................29 ONT environmental requirements .............................................................29 Storage......................................................................................................29 Transportation ...........................................................................................30 Stationary use............................................................................................30 Thermal limitations ....................................................................................30 Material content compliance......................................................................30 End-of-life collection and treatment...........................................................31 G-240W-G unit data sheet ............................................................33 G-240W-G part numbers and identification...............................................33 G-240W-G general description..................................................................34 Configuring the G-240W-G to function as a single port ONT ....................36 Support for CFM over S-tunnel..................................................................36 TR-069 parameter support ........................................................................37 Host object support....................................................................................37 Port forwarding support .............................................................................37 Optical parameters support .......................................................................38 Object support for Wi-Fi parameters .........................................................38 Statistics and troubleshooting support.......................................................38 Diagnostic parameter support ...................................................................38 Timing parameter support .........................................................................39 Independent TR69 session with Saas.......................................................39 TR69 authentication using TLS and CA certificates..................................39 TR-104 parameter extension support for voice service.............................39 TR-104 voice-related alarms .....................................................................40 TR-104 parameters for FX line testing ......................................................40 TR-111 support..........................................................................................40 TR-181 parameter support ........................................................................40 Mobile offload support ...............................................................................42 Support for soft GRE tunnels.....................................................................42 GRE...........................................................................................................42 Soft GRE ...................................................................................................43 G-240W-G software and installation feature support ................................44 G-240W-G interfaces and interface capacity.............................................44 G-240W-G connections and components .................................................44 G-240W-G LEDs .......................................................................................47 G-240W-G detailed specifications.............................................................49 G-240W-G GEM ports and T-CONTs........................................................50 G-240W-G performance monitoring statistics ...........................................51 G-240W-G functional blocks......................................................................53 G-240W-G standards compliance .............................................................55 Energy-related products standby and off modes compliance....................55 FCC statement ..........................................................................................56 FCC Radiation Exposure Statement .........................................................56 G-240W-G special considerations.............................................................56 Wi-Fi service..............................................................................................57 Wi-Fi physical features ..............................................................................57 Wi-Fi standards and certifications .............................................................57 3.2 3.3 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 4 4.1 4.2 4.2.1 4.2.2 4.2.3 4.2.3.1 4.2.3.2 4.2.3.3 4.2.3.4 4.2.3.5 4.2.3.6 4.2.3.7 4.2.4 4.2.5 4.2.6 4.2.7 4.2.8 4.2.9 4.2.10 4.2.11 4.2.12 4.2.12.1 4.2.12.2 4.3 4.4 4.4.1 4.5 4.6 4.7 4.8 4.9 4.10 4.10.1 4.10.2 4.10.3 4.11 4.11.1 4.11.1.1 4.11.1.2 10 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide 4.11.1.3 4.11.2 5 5.1 5.2 5.3 5.4 5.5 5.6 6 6.1 6.2 6.3 6.4 6.5 6.6 7 7.1 7.2 7.2.1 7.2.2 7.2.3 7.2.4 7.2.5 7.2.6 7.2.7 7.3 7.3.1 7.3.2 7.3.3 7.3.4 8 8.1 8.2 8.2.1 8.3 Wi-Fi GUI features.....................................................................................57 G-240W-G ONT considerations and limitations ........................................57 Install a G-240W-G indoor ONT ...................................................59 Purpose .....................................................................................................59 General......................................................................................................59 Prerequisites..............................................................................................59 Recommended tools..................................................................................59 Safety information......................................................................................60 Procedure..................................................................................................61 Replace a G-240W-G indoor ONT................................................65 Purpose .....................................................................................................65 General......................................................................................................65 Prerequisites..............................................................................................65 Recommended tools..................................................................................65 Safety information......................................................................................66 Procedure..................................................................................................67 Configure a G-240W-G indoor ONT.............................................71 General......................................................................................................71 HGU mode GUI configuration....................................................................71 Login..........................................................................................................71 Device and connection status....................................................................72 Network configuration................................................................................89 Security configuration..............................................................................115 Application configuration .........................................................................127 Maintenance............................................................................................137 RG troubleshooting counters...................................................................152 SFU mode configuration..........................................................................154 Switch from default HGU mode to SFU mode.........................................154 Login........................................................................................................156 Device and connection status..................................................................157 Maintenance............................................................................................158 ONT configuration file over OMCI .............................................163 Purpose ...................................................................................................163 Supported configuration file types ...........................................................163 Filename conventions..............................................................................165 ONT configuration file over OMCI ...........................................................165 Issue: 01 3FE-47555-AAAA-TCZZA 11 7368 ISAM ONT G-240W-G Product Guide 12 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide List of figures 2 Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 3 Figure 6 Figure 7 Figure 8 4 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 Figure 14 Figure 15 5 Figure 16 6 Figure 17 7 Figure 18 Figure 19 Figure 20 Figure 21 Figure 22 Figure 23 Figure 24 Figure 25 Figure 26 Figure 27 Figure 28 Figure 29 Figure 30 Figure 31 Figure 32 Figure 33 Figure 34 Figure 35 Figure 36 ETSI ONT safety guidelines .........................................................17 PSE certification ........................................................................................19 Laser product label....................................................................................23 Laser classification label............................................................................23 Laser warning labels..................................................................................24 Sample laser product safety label on the ONT equipment........................25 ETSI environmental and CRoHS guidelines...............................27 Products below MCV value label...............................................................28 Products above MCV value label ..............................................................28 Recycling/take back/disposal of product symbol.......................................31 G-240W-G unit data sheet ............................................................33 Soft GRE-based architecture.....................................................................43 G-240W-G indoor ONT physical connections ...........................................45 G-240W-G ONT without fiber cover ..........................................................46 G-240W-G ONT with fiber cover ...............................................................46 G-240W-G indoor ONT LEDs....................................................................48 Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS and without RF video........................................................................................53 G-240W-G ONT hardware block ...............................................................54 Install a G-240W-G indoor ONT ...................................................59 G-240W-G ONT with connections and key mounting holes......................62 Replace a G-240W-G indoor ONT................................................65 G-240W-G indoor ONT connections .........................................................67 Configure a G-240W-G indoor ONT.............................................71 Web login window......................................................................................72 Device Information window........................................................................73 LAN status window....................................................................................75 WAN status window...................................................................................77 WAN status IPv6 window ..........................................................................78 Home networking information window.......................................................80 Optics module status window....................................................................81 LAN ports Statistics window ......................................................................83 WAN ports statistics window .....................................................................84 WAN ports statistics message...................................................................85 WLAN ports statistics window ...................................................................86 WLAN ports statistics message.................................................................87 Voice Information window..........................................................................88 LAN network window.................................................................................90 LAN IPv6 network window.........................................................................92 WAN network window................................................................................94 WAN DHCP window..................................................................................96 WiFi 2.4G network window........................................................................97 WiFi 5G network window.........................................................................100 Issue: 01 3FE-47555-AAAA-TCZZA 13 7368 ISAM ONT G-240W-G Product Guide Figure 37 Figure 38 Figure 39 Figure 40 Figure 41 Figure 42 Figure 43 Figure 44 Figure 45 Figure 46 Figure 47 Figure 48 Figure 49 Figure 50 Figure 51 Figure 52 Figure 53 Figure 54 Figure 55 Figure 56 Figure 57 Figure 58 Figure 59 Figure 60 Figure 61 Figure 62 Figure 63 Figure 64 Figure 65 Figure 66 Figure 67 Figure 68 Figure 69 Figure 70 Figure 71 Figure 72 Figure 73 Figure 74 Figure 75 Figure 76 Figure 77 Figure 78 Figure 79 Wireless Schedule window......................................................................102 Routing network window..........................................................................103 DNS network window ..............................................................................105 TR-069 network window..........................................................................106 GRE Tunnel window................................................................................107 QoS Config window (L2)..........................................................................109 QoS Config window (L3)..........................................................................110 US Classifier Policy window ....................................................................112 US Classifier window...............................................................................113 US Classifier Rules window.....................................................................114 Firewall window .......................................................................................116 MAC filter window....................................................................................117 IP filter window ........................................................................................119 URL Filter window ...................................................................................120 Parental Control window..........................................................................123 DMZ and ALG window.............................................................................125 Access Control window ...........................................................................126 Port forwarding window ...........................................................................128 Port Triggering window............................................................................129 DDNS window .........................................................................................131 NTP window ............................................................................................132 USB window ............................................................................................134 UPnP and DLNA window.........................................................................135 Voice setting window...............................................................................136 Password window....................................................................................139 Speed Test window .................................................................................140 LOID Config window................................................................................141 SLID configuration window......................................................................142 Device management window...................................................................143 Backup and Restore window...................................................................144 Firmware upgrade window ......................................................................145 Reboot window........................................................................................146 Factory default window............................................................................147 Diagnose window ....................................................................................148 Log window..............................................................................................149 PPPoE Diagnostics window ....................................................................151 PPPoE diagnostics results ......................................................................152 RG Troubleshooting Counters window....................................................153 Web login window....................................................................................156 Device Information window......................................................................157 Password window....................................................................................159 LOID configuration window......................................................................160 SLID configuration window......................................................................161 14 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide List of tables 2 Table 1 4 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 9 Table 10 Table 11 Table 12 Table 13 Table 14 Table 15 Table 16 7 Table 17 Table 18 Table 19 Table 20 Table 21 Table 22 Table 23 Table 24 Table 25 Table 26 Table 27 Table 28 Table 29 Table 30 Table 31 Table 32 Table 33 Table 34 Table 35 Table 36 Table 37 Table 38 ETSI ONT safety guidelines .........................................................17 Safety labels..............................................................................................18 G-240W-G unit data sheet ............................................................33 Identification of G-240W-G indoor ONTs...................................................33 G-240W-G power supply...........................................................................34 Support for TR-181 parameter categories.................................................41 G-240W-G indoor ONT interface connection capacity ..............................44 G-240W-G indoor ONT physical connections ...........................................47 G-240W-G indoor ONT LED descriptions .................................................48 G-240W-G indoor ONT physical specifications.........................................49 G-240W-G indoor ONT power consumption specifications.......................50 G-240W-G indoor ONT environmental specifications ...............................50 G-240W-G indoor ONT capacity for GEM ports and T-CONTs.................50 Package P ONTs ONTENET performance monitoring statistics...............51 Package P ONTs ONTL2UNI performance monitoring statistics ..............51 Package P ONTs PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP performance monitoring statistics..............................................................52 Package P ONTs PONONTTC aggregate performance monitoring statistics.....................................................................................................52 G-240W-G ONT considerations and limitations ........................................57 Configure a G-240W-G indoor ONT.............................................71 Device Information parameters .................................................................73 LAN status parameters..............................................................................75 WAN status parameters ............................................................................77 WAN status IPv6 parameters ....................................................................79 Home networking parameters ...................................................................80 Optics module status parameters..............................................................82 Voice Information parameters ...................................................................88 LAN network parameters...........................................................................90 LAN IPv6 network parameters...................................................................92 WAN network parameters .........................................................................94 WAN DHCP parameters............................................................................96 WiFi 2.4G network parameters..................................................................97 WiFi 5G network parameters...................................................................100 Routing network parameters ...................................................................104 DNS network parameters ........................................................................105 TR-069 network parameters....................................................................106 GRE Tunnel parameters..........................................................................107 QoS Config parameters...........................................................................110 US Classifier Policy parameters..............................................................112 US Classifier parameters.........................................................................113 US Classifier Rules parameters ..............................................................115 Firewall parameters.................................................................................116 Issue: 01 3FE-47555-AAAA-TCZZA 15 7368 ISAM ONT G-240W-G Product Guide Table 39 Table 40 Table 41 Table 42 Table 43 Table 44 Table 45 Table 46 Table 47 Table 48 Table 49 Table 50 Table 51 Table 52 Table 53 Table 54 Table 55 Table 56 Table 57 Table 58 Table 59 8 Table 60 MAC filter parameters..............................................................................118 IP filter parameters ..................................................................................119 URL Filter parameters .............................................................................121 Parental control parameters ....................................................................124 DMZ and ALG parameters ......................................................................125 Access control parameters......................................................................126 Port forwarding parameters.....................................................................128 Port triggering parameters.......................................................................129 DDNS parameters ...................................................................................131 NTP parameters ......................................................................................132 USB parameters......................................................................................134 Voice setting parameters.........................................................................136 Password parameters..............................................................................139 LOID configuration parameters ...............................................................141 SLID configuration parameters................................................................142 Device management parameters ............................................................143 PPPoE diagnostics results parameters ...................................................152 RG Troubleshooting Counters parameters..............................................153 Device Information parameters ...............................................................158 Password parameters..............................................................................159 SLID configuration parameters................................................................161 ONT configuration file over OMCI .............................................163 Supported configuration files...................................................................164 16 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide ETSI ONT safety guidelines 2 ETSI ONT safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals (ONTs). 2.1 Safety instructions This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment. 2.1.1 Safety instruction boxes The safety instruction boxes are provided in the ONT customer documentation. Observe the instructions to meet safety requirements. The following is an example of the Danger box. Danger Possibility of personal injury. The Danger box indicates that the described activity or situation may pose a threat to personal safety. It calls attention to a situation or procedure which, if not correctly performed or adhered to, may result in death or serious physical harm. Do not proceed beyond a Danger box until the indicated conditions are fully understood and met. The following is an example of the Warning box. Warning 1 Possibility of equipment damage. Warning 2 Possibility of data loss. The Warning box indicates that the described activity or situation may, or will, cause equipment damage, loss of data, or serious performance problems. It identifies a possible equipment-damaging situation or provides essential information to avoid the degradation of system operations or data. Do not proceed beyond a warning until the indicated conditions are fully understood and met. Issue: 01 3FE-47555-AAAA-TCZZA 17 ETSI ONT safety guidelines 7368 ISAM ONT G-240W-G Product Guide The following is an example of the Caution box. Caution 1 Possibility of service interruption. Caution 2 Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met. The following is an example of the Note box. Note Information of special interest. The Note box provides information that assists the personnel working with ONTs. It does not provide safety-related instructions. 2.1.2 Safety-related labels The ONT equipment is labeled with the specific safety instructions and compliance information that is related to a variant of the ONT. Observe the instructions on the safety labels. Table 1 provides sample safety labels on the ONT equipment. Table 1 Safety labels Description ESD warning Label text Caution: This assembly contains an electrostatic sensitive device. Laser classification Class 1 laser product PSE marking These power supplies are Japan PSE certified and compliant with Japan VCCI emissions standards. Figure 1 shows the PSE certification. 18 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide ETSI ONT safety guidelines Figure 1 PSE certification This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. Warning 2.2 Safety standards compliance This section describes the ONT compliance with the European safety standards. 19841 2.2.1 EMC, EMI, and ESD compliance The ONT equipment complies with the following EMC, EMI, and ESD requirements:

EN 300-328 v1.9.1 wide band data transmission standards for 2.4GHz bands EN 300-386 V1.5.1: Electromagnetic Compatibility and Radio Spectrum Matters

(ERM): Telecommunications Network Equipment; Electromagnetic Compatibility

(EMC) requirements; Electrostatic Discharge (ESD) requirements EN 55022 (2006): Class B, Information Technology Equipment, Radio Disturbance Characteristics, limits and methods of measurement EN 55024 (2010): Information Technology Equipment, Immunity Characteristics, limits and methods of measurement European Council Directive 2004/108/EC EN 300-386 V1.4.1: 2008 EN 55022:2006 Class B (ONTs) 2.2.2 Equipment safety standard compliance The ONT equipment complies with the requirements of EN 60950-1, Safety of Information Technology Equipment for use in a restricted location (per R-269). Issue: 01 3FE-47555-AAAA-TCZZA 19 ETSI ONT safety guidelines 7368 ISAM ONT G-240W-G Product Guide 2.2.3 Environmental standard compliance The ONT equipment complies with the EN 300 019 European environmental standards. 2.2.4 CE RED RF Radiation Exposure Statement This device complies with CE RED radiation exposure limits set forth for an uncontrolled environment. To comply with CE RED RF exposure compliance requirements, this grant is applicable only for mobile configurations. The antennas used for the transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 2.2.5 Laser product standard compliance For most ONTs, the ONT equipment complies with EN 60825-1 and IEC 60825-2 for laser products. If there is an exception to this compliance regulation, you can find this information in the standards compliance section of the unit data sheet in this Product Guide. 2.2.6 Resistibility requirements compliance The ONT equipment complies with the requirements of ITU Recommendation K.21 for resistibility of telecommunication equipment installed in customer premises to over voltage and overcurrents. 2.2.7 Acoustic noise emission standard compliance The ONT equipment complies with EN 300 753 acoustic noise emission limit and test methods. 20 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide ETSI ONT safety guidelines 2.3 Electrical safety guidelines This section provides the electrical safety guidelines for the ONT equipment. Note 1 The ONTs comply with the U.S. National Electrical Code. However, local electrical authorities have jurisdiction when there are differences between the local and U.S. standards. Note 2 The ONTs comply with BS EN 61140. 2.3.1 Power supplies The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property. 2.3.2 Cabling The following are the guidelines regarding cables used for the ONT equipment:

All cables must be approved by the relevant national electrical code. The cables for outdoor installation of ONTs must be suitable for outdoor use. POTS wiring run outside the subscriber premises must comply with the requirements of local electrical codes. In some markets, the maximum allowed length of the outside run is 140 feet (43 m). If the outside run is longer, NEC requires primary protection at both the exit and entry points for the wire. 2.3.3 Protective earth Earthing and bonding of the ONTs must comply with the requirements of local electrical codes. Issue: 01 3FE-47555-AAAA-TCZZA 21 ETSI ONT safety guidelines 7368 ISAM ONT G-240W-G Product Guide 2.4 ESD safety guidelines The ONT equipment is sensitive to ESD. Operations personnel must observe the following ESD instructions when they handle the ONT equipment. Caution This equipment is ESD sensitive. Proper ESD protections should be used when you enter the TELCO Access portion of the ONT. During installation and maintenance, service personnel must wear wrist straps to prevent damage caused by ESD. 2.5 Laser safety guidelines Observe the following instructions when you perform installation, operations, and maintenance tasks on the ONT equipment. Only qualified service personnel who are extremely familiar with laser radiation hazards should install or remove the fiber optic cables and units in this system. Danger There may be invisible laser radiation at the fiber optic cable when the cable is removed from the connector. Avoid direct exposure to the laser beam. Observe the following danger for laser hazard. Eyes can be damaged when they are exposed to a laser beam. Take necessary precautions before you plug in the optical modules. Danger Possibility of equipment damage. Risk of eye damage by laser radiation. 2.5.1 Laser classification The ONT is classified as a Class 1 laser product based on its transmit optical output. 2.5.1.1 Laser warning labels The following figures show the labels related to laser product, classification and warning. 22 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide ETSI ONT safety guidelines Figure 2 shows a laser product label. Figure 2 Laser product label Figure 3 shows a laser classification label. Laser classification labels may be provided in other languages. Figure 3 Laser classification label 18455 CLASS 1 LASER PRODUCT PRODUCTO LASER CLASE 1

'

'

CLASE 1 DEL LASER LASER CLASSE 1 18992 Figure 4 shows a laser warning label and an explanatory label for laser products. Labels and warning may be provided in other languages. The explanatory label provides the following information:

a warning that calls attention to the invisible laser radiation an instruction against staring into the beam or viewing directly with optical instruments wavelength normal output power maximum output power Issue: 01 3FE-47555-AAAA-TCZZA 23 ETSI ONT safety guidelines 7368 ISAM ONT G-240W-G Product Guide Figure 4 Laser warning labels INVISIBLE LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Wavelength(s): xxxx nm Normal output power: xx m W Max output power: yyy m W Laser Warning Label Laser Warning Label CLASS 1 LASER PRODUCT RAYONNEMENT LASER CLASSE 1 RAYONNEMENT LASER INVISIBLE

'

EVITER TOUTE EXPOSITION AU FAISCEAU NE PAS DEMONTER. FAIRE APPEL A UN PERSONNELL QUALIFIE RADIACION DE LASER INVISIBLE. EVITAR CUALOUIER EXPOSICION AL RAYO LASER. NO DESMONTAR. LLAMAR A PERSONAL AUTORIZADO CLASE 1 DEL LASER INVISIBLE LASER RADIATION PRESENT AT FIBER OPTIC CABLE WHEN NOT CONNECTED. AVOID DIRECT EXPOSURE TO BEAM. Laser Warning Label 18993 2.5.2 Laser classification The ONT is classified as a Class 1 laser product based on its transmit optical output. For Class 1 laser products, lasers are safe under reasonably foreseeable conditions of operation, including the use of optical instruments for intrabeam viewing. Figure 5 shows a sample laser product safety label on the ONT equipment. 24 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide ETSI ONT safety guidelines Figure 5 Sample laser product safety label on the ONT equipment 2.5.3 Transmit optical output The maximum transmit optical output of an ONT is +5 dBm. 2.5.4 Normal laser operation In normal operation, fiber cable laser radiation is always off until it receives signal from the line terminal card. Eyes can be damaged when they exposed to a laser beam. Operating personnel must observe the instructions on the laser explanatory label before plugging in the optical module. Danger Risk of eye damage by laser radiation. 2.5.5 Location class Use cable supports and guides to protect the receptacles from strain. 2.6 Environmental requirements See the ONT technical specification documentation for more information about temperature ranges. Issue: 01 3FE-47555-AAAA-TCZZA 25 ETSI ONT safety guidelines 7368 ISAM ONT G-240W-G Product Guide During operation in the supported temperature range, condensation inside the ONT caused by humidity is not an issue. To avoid condensation caused by rapid changes in temperature and humidity, Nokia recommends:

The door of the ONT not be opened until temperature inside and outside the enclosure has stabilized. If the door of the ONT must be opened after a rapid change in temperature or humidity, use a dry cloth to wipe down the metal interior to prevent the risk of condensation. When high humidity is present, installation of a cover or tent over the ONT helps prevent condensation when the door is opened. 26 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide ETSI environmental and CRoHS guidelines 3 ETSI environmental and CRoHS guidelines This chapter provides information about the ETSI environmental China Restriction of Hazardous Substances (CRoHS) regulations that govern the installation and operation of the optical line termination (OLT) and optical network termination (ONT) systems. This chapter also includes environmental operation parameters of general interest. 3.1 Environmental labels This section describes the environmental instructions that are provided with the customer documentation, equipment, and location where the equipment resides. 3.1.1 Overview CRoHS is applicable to Electronic Information Products (EIP) manufactured or sold and imported in the territory of the mainland of the Peoples Republic of China. EIP refers to products and their accessories manufactured by using electronic information technology, including electronic communications products and such subcomponents as batteries and cables. 3.1.2 Environmental related labels Environmental labels are located on appropriate equipment. The following are sample labels. 3.1.2.1 Products below Maximum Concentration Value

(MCV) label Figure 6 shows the label that indicates a product is below the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products). Products with this label are recyclable. The label may be found in this documentation or on the product. Issue: 01 3FE-47555-AAAA-TCZZA 27 ETSI environmental and CRoHS guidelines 7368 ISAM ONT G-240W-G Product Guide Figure 6 Products below MCV value label 18986 3.1.2.2 Products containing hazardous substances above Maximum Concentration Value (MCV) label Figure 7 shows the label that indicates a product is above the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products). The number contained inside the label indicates the Environment-Friendly User Period (EFUP) value. The label may be found in this documentation or on the product. Figure 7 Products above MCV value label 28 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide ETSI environmental and CRoHS guidelines Together with major international telecommunications equipment companies, Nokia has determined it is appropriate to use an EFUP of 50 years for network infrastructure equipment and an EFUP of 20 years for handsets and accessories. These values are based on manufacturers' extensive practical experience of the design, manufacturing, maintenance, usage conditions, operating environments, and physical condition of infrastructure and handsets after years of service. The values reflect minimum values and refer to products operated according to the intended use conditions. See Hazardous Substances Table (HST) for more information. 3.2 Hazardous Substances Table (HST) This section describes the compliance of the OLT and ONT equipment to the CRoHS standard when the product and subassemblies contain hazardous substances beyond the MCV value. This information is found in this user documentation where part numbers for the product and subassemblies are listed. It may be referenced in other OLT and ONT documentation. In accordance with the Peoples Republic of China Electronic Industry Standard Marking for the Control of Pollution Caused by Electronic Information Products

(SJ/T11364-2006), customers may access the Nokia Hazardous Substance Table, in Chinese, from the following location:

http://www.nokia-sbell.com/wwwroot/images/upload/private/1/media/ChinaRoHS.p df 3.3 Other environmental requirements Observe the following environmental requirements when handling the P-OLT or ONT equipment. 3.3.1 ONT environmental requirements See the ONT technical specification documentation for more information about temperature ranges. 3.3.2 Storage According to ETS 300-019-1-1 - Class 1.1, storage of OLT equipment must be in Class 1.1, weather-protected, temperature-controlled locations. Issue: 01 3FE-47555-AAAA-TCZZA 29 ETSI environmental and CRoHS guidelines 7368 ISAM ONT G-240W-G Product Guide 3.3.3 Transportation According to EN 300-019-1-2 - Class 2.3, transportation of the OLT equipment must be in packed, public transportation with no rain on packing allowed. 3.3.4 Stationary use According to EN 300-019-1-3 - Class 3.1/3.2/3.E, stationary use of OLT equipment must be in a temperature-controlled location, with no rain allowed, and with no condensation allowed. 3.3.5 Thermal limitations When the OLT is installed in the CO or CEV, install air filters on the P-OLT. The thermal limitations for OLT operation in a CO or CEV are:

operating temperature: 5C to 40C (41F to 104F) short-term temperature: 5C to 50C (23F to 122F) operating relative humidity: 5% to 85%

short-term relative humidity: 5% to 95%, but not to exceed 0.024 kg of water/kg 3.3.6 Material content compliance European Union (EU) Directive 2002/95/EC, Restriction of the use of certain Hazardous Substances (RoHS), restricts the use of lead, mercury, cadmium, hexavalent chromium, and certain flame retardants in electrical and electronic equipment. This Directive applies to electrical and electronic products placed on the EU market after 1 July 2006, with various exemptions, including an exemption for lead solder in network infrastructure equipment. Nokia products shipped to the EU after 1 July 2006 comply with the EU RoHS Directive. Nokia has implemented a material/substance content management process. The process is described in: Nokia process for ensuring RoHS Compliance

(1AA002660031ASZZA). This ensures compliance with the European Union Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS2). With the process equipment is assessed in accordance with the Harmonised Standard EN50581:2012 (CENELEC) on Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances. 30 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide ETSI environmental and CRoHS guidelines 3.3.7 End-of-life collection and treatment Electronic products bearing or referencing the symbol shown in Figure 8, when put on the market within the European Union (EU), shall be collected and treated at the end of their useful life, in compliance with applicable EU and local legislation. They shall not be disposed of as part of unsorted municipal waste. Due to materials that may be contained in the product, such as heavy metals or batteries, the environment and human health may be negatively impacted as a result of inappropriate disposal. Note In the European Union, a solid bar under the symbol for a crossed-out wheeled bin indicates that the product was put on the market after 13 August 2005. Figure 8 Recycling/take back/disposal of product symbol At the end of their life, the OLT and ONT products are subject to the applicable local legislations that implement the European Directive 2012/19EU on waste electrical and electronic equipment (WEEE). There can be different requirements for collection and treatment in different member states of the European Union. In compliance with legal requirements and contractual agreements, where applicable, Nokia will offer to provide for the collection and treatment of Nokia products bearing the logo shown in Figure 8 at the end of their useful life, or products displaced by Nokia equipment offers. For information regarding take-back of equipment by Nokia, or for more information regarding the requirements for recycling/disposal of product, contact your Nokia account manager or Nokia take back support at sustainability.global@nokia.com. Issue: 01 3FE-47555-AAAA-TCZZA 31 ETSI environmental and CRoHS guidelines 7368 ISAM ONT G-240W-G Product Guide 32 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide G-240W-G unit data sheet 4 G-240W-G unit data sheet 4.1 G-240W-G part numbers and identification 4.2 G-240W-G general description 4.3 G-240W-G software and installation feature support 4.4 G-240W-G interfaces and interface capacity 4.5 G-240W-G LEDs 4.6 G-240W-G detailed specifications 4.7 G-240W-G GEM ports and T-CONTs 4.8 G-240W-G performance monitoring statistics 4.9 G-240W-G functional blocks 4.10 G-240W-G standards compliance 4.11 G-240W-G special considerations 4.1 G-240W-G part numbers and identification Table 2 provides part numbers and identification information for the G-240W-G indoor ONT. Table 2 Identification of G-240W-G indoor ONTs Ordering kit part number Provisioning number Description CLEI CPR 3FE 47536 AA

(Customer-specific variant) 3FE 47536 AB

(Customer-specific variant) 3FE 47555 AA 3FE 47555 BA GPON indoor ONT, 2 POTS, 4 10/100/1000 Base-T Ethernet interfaces, WiFi 802.11n 2x2 and 802.11 ac 3x3, maximum power excluding antenna, customer-specific pre configuration file, SC/APC, AC/DC power adapter with LED, US plug, and customer logo. GPON indoor ONT, 2 POTS, 4 10/100/1000 Base-T Ethernet interfaces, WiFi 802.11n 2x2 and 802.11 ac 3x3, maximum power excluding antenna, customer-specific pre configuration file, SC/APC, AC/DC power adapter with LED, US plug, and customer logo.

(1 of 2) ECI/

Bar code Issue: 01 3FE-47555-AAAA-TCZZA 33 G-240W-G unit data sheet 7368 ISAM ONT G-240W-G Product Guide Ordering kit part number Provisioning number Description 3FE 47536 AC

(Customer-specific variant) 3FE 47555 CA GPON indoor ONT, 2POTS, 4 10/100/1000 Base-T Ethernet interfaces, WiFi 802.11n 2x2 and 802.11 ac 3x3, maximum power excluding antenna, customer-specific pre configuration file, SC/APC, AC/DC power adapter with LED, US plug, and customer logo.

(2 of 2) CLEI CPR ECI/

Bar code Table 3 provides the power supply information for the G-240W-G ONT. For more information on power supplies, see the 7368 ISAM ONT Power Supply and UPS Guide. Table 3 G-240W-G power supply ONT part numbers Power model Kit: 3FE 47536 AA EMA: 3FE 47555 AA Kit: 3FE 47536 AB EMA: 3FE 47555 BA Kit: 3FE 47536 AC EMA: 3FE 47555 CA Mass Power RD1203000-C55-2 0MG MSA-C3000CS12. 0-40W-US 1L43-US1230 Mass Power RD1203000-C55-2 0MG MSA-C3000CS12. 0-40W-US 1L43-US1230 Mass Power RD1203000-C55-2 0MG MSA-C3000CS12. 0-40W-US 1L43-US1230 Power information 36 Watt AC/DC power adapter 36 Watt AC/DC power adapter 36 Watt AC/DC power adapter 36 Watt AC/DC power adapter 36 Watt AC/DC power adapter 36 Watt AC/DC power adapter Customer category or country compliance tested for ETSI, IEC 60950-1 Notes 2-pin US input plug with LED 2-pin US input plug with LED 2-pin US input plug with LED 2-pin US input plug with LED 2-pin US input plug with LED 2-pin US input plug with LED 4.2 G-240W-G general description G-240W-G indoor ONTs provide the subscriber interface for the network by terminating the PON interface and converting it to user interfaces that directly connect to subscriber devices. The ONT is compatible with all existing subscriber equipment, including analog phones with both tone and rotary dial capabilities, cordless phones, modems, fax machines, and caller ID boxes (Type I, Type II, and Type III). 34 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide G-240W-G unit data sheet G-240W-G indoor ONTs provide the following functions:

Single fiber GPON interface with 1.244Gbit/s upstream and 2.488Gbit/s downstream data rates filtering. Advanced data features such as VLAN tag manipulation, classification, and Traffic classification and QoS capability Analog Telephone Adapter (ATA) function integrated based on SIP (RFC3261), with various CLASS services supported, including Caller ID, Call Waiting, Call Forwarding, and Call Transfer Internal Switch 5 REN per line Multiple voice Codec MDI/MDIX auto-negotiation Line Rate L2 traffic UPnP IGD2.0 support Bridged mode or routed mode per LAN port Optics that support received signal strength indication (RSSI) WPS on wireless authorization support 802.11ac support 2.4GHz/5GHz dual band concurrency, both with configurable Wi-Fi tx power from 100mW to 500mW, in 100mW increments (as constrained by local regulations). Internal DHCP server, with configurable DHCP pool and gateway antenna gain: 2.4G and 5G WiFi: 3dBi Enhanced ONT; SSH-Telnet-FTP and http server are disabled from the WAN side Concurrent 802.11n 2x2 MIMO in 2.4GHz and 802.11ac 3x3 MIMO in 5GHz 64/128 WEP encryption WPA, WPA-PSK/TKIP WPA2, WPA2-PSK/AES support for multiple SSIDs (private and public instances); contact your Nokia representative for further details. WLAN on/off push button WPS/PBC button (for 2.4G and 5G) Ethernet-based Point-to-Point (PPPoE) Network Address Translation (NAT) Network Address Port Translation (NAPT) ALG and UPnP port forwarding DMZ Multi-level firewall DNS server DHCP client/server support HT20/HT40 for 802.11b/g/n, and HT20/40/80 for 802.11AC support for up to 32 simultaneous wireless connections IP/MAC filter Issue: 01 3FE-47555-AAAA-TCZZA 35 G-240W-G unit data sheet 7368 ISAM ONT G-240W-G Product Guide External USB HD (Hard Drive) support, accessible to all LAN devices support for AIS with DOWN MEP 4.2.1 Configuring the G-240W-G to function as a single port ONT In addition to functioning as a residential gateway, the G-240W-G ONT can be configured to function as a single port ONT. In the custom configuration, the ONT reports to the OLT as one PPTP port. The physical Ethernet port of the ONT is managed by the RGW using the TR-069 protocol, rather than by the ONT/OMCI. To enable the ONT to function as a single port ONT, the value of the parameter:

InternetGatewayDevice.DeviceInfo.X_ALU-COM_PortReport2OLT.PPTP must be set to PPTP_one A custom pre-configuration file is required to operate the G-240W-G as a single-port ONT. Contact your Nokia support engineer to arrange for a custom pre-configuration file. 4.2.2 Support for CFM over S-tunnel The G-240W-G ONT supports Connectivity Fault Management (CFM) over S-tunnel. This feature eliminates the need for creating many UP MEPs to handle CFM frames with each inner VLAN tag. The UP MEP can be configured using the CLI. Down MEP over S-tunnel is not supported. To configure the S-tunnel, type the following commands:

configure vlan id stacked:1025:0 mode cross-connect in-qos-prof-name name:Default_TC0 mac-mcast-ctrl configure vlan id stacked:1026:0 mode residential-bridge in-qos-prof-name name:Default_TC0 mac-mcast-ctrl To configure the UP MEP, type the following commands:

configure cfm domain 5 name string:MD1 level 1 configure cfm domain 5 association 1 vlan stacked:1025:0 name string:MA1 configure cfm domain 5 association 1 mep 2 location user:1/1/1/1/1/1/1 36 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide G-240W-G unit data sheet The current design does not support the propagation of AIS frames with VLAN information from the received packet. As a result, when a downstream AIS frame is received for UP MEP over S-tunnel, the propagated AIS packet will not contain the VLAN information. 4.2.3 TR-069 parameter support The G-240W-G ONT supports the following TR-069 features:

Host object Port forwarding Optical parameters Object support for Wi-Fi parameters Statistics and troubleshooting Diagnostic parameter Timing parameter 4.2.3.1 Host object support The ONT provides host object support for:

InternetGatewayDeviceLANDevice.Hosts.Host. 4.2.3.2 Port forwarding support The ONT supports the port forwarding of objects via TR-069:

Application Name WAN Port LAN Port Protocol Enable Mapping WAN Connection List Internal Client These are the same port forwarding parameters supported in the GUI. For more information, see Table 45 in the chapter Configure a G-240W-G indoor ONT. Issue: 01 3FE-47555-AAAA-TCZZA 37 G-240W-G unit data sheet 7368 ISAM ONT G-240W-G Product Guide 4.2.3.3 Optical parameters support laser bias current The ONT supports the reading of optical parameters via TR-069:

voltage temperature received signal levels lower thresholds These are the same optical parameters supported in the GUI. For more information, see Table 22 in the chapter Configure a G-240W-G indoor ONT. 4.2.3.4 Object support for Wi-Fi parameters The ONT supports the status retrieval and configuration of the following Wi-Fi parameters via TR-069:

channel SSID password for WPA and WEP Tx power (transmission rate in percentage of maximum transmit power) WPS These are the same TR-069 object parameters that are supported in the GUI. For more information, see Tables 28 and 29 in the chapter Configure a G-240W-G indoor ONT. 4.2.3.5 Statistics and troubleshooting support The ONT supports TR-069 statistics and troubleshooting for LAN, WAN, and WiFi. For more information, see the Procedure Statistics retrieval in the chapter Configure a G-240W-G indoor ONT. 4.2.3.6 Diagnostic parameter support The ONT supports the following TR-069 diagnostic parameters:

TR-143 IP ping traceroute 38 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide G-240W-G unit data sheet These are the same diagnostic parameters supported in the GUI. For more information, see Procedure Diagnose WAN connections in the chapter Configure a G-240W-G indoor ONT. 4.2.3.7 Timing parameter support The ONT supports TR-069 timing parameters. 4.2.4 Independent TR69 session with Saas The prime communication between the Nokia Motive cloud solution and the G-240W-G ONT is TR-069. To keep the Nokia solution independent from the ACS solution of the carrier, the ONT can establish an independent TR-069 session with the Saas. The Saas WiFi Care URL and credentials can be programmed from the ACS solution of the carrier, or they can be incorporated in a pre-configuration file. 4.2.5 TR69 authentication using TLS and CA certificates G-240W-G ONTs support TLS, as well as ACS authentication using SHA-256 pre-installed certificates. If the URL is set to the https://... format, by default, the connection will use TLS without authentication mode. The ONT can also authenticate the ACS using a pre-installed CA certificate. 4.2.6 TR-104 parameter extension support for voice service A proprietary attribute has been added to the TR-104 Voice Service object structure to enable the ACS to configure the name of the embedded GSIP XML file to be selected. The TR-104 Voice Service Object is:

InternetGatewayDevice.Services.VoiceService.{i}.Capabilities.SIP. The proprietary attribute is: X_ALU-COM_XML_File_Name_Path. Issue: 01 3FE-47555-AAAA-TCZZA 39 G-240W-G unit data sheet 7368 ISAM ONT G-240W-G Product Guide 4.2.7 TR-104 voice-related alarms The G-240W-G ONT supports the following four TR-104 voice-related alarms on a per FXS port basis. These alarms all represent SIP registration failures with an alarm level of MAJOR. SIPREGDNS: domain name could not be resolved SIPREGAUTH: authentication failed SIPREGTO: re-transmissions timed out SIPREGERFRSP: error response from the registration server 4.2.8 TR-104 parameters for FX line testing New attributes have been added to the TR-104 Voice Service object structure to enable the ACS to perform line tests. The ONT supports the following electrical line tests:

hazardous potential foreign electrical motive force resistive faults receiver off-hook test ringers test 4.2.9 TR-111 support The G-240W-G ONT supports TR-111, which extends the WAN Management Protocol defined in TR-069 to enhance the ability to remotely manage LAN devices. The device-gateway association enables an ACS to identify the associated gateway through which a device is connected. A connect request via the NAT gateway enables an ACS to initiate a TR-069 session with a device that is operating behind a NAT gateway. 4.2.10 TR-181 parameter support TR-181 parameter support has been introduced or enhanced for the parameter categories and functions listed in Table 4. For details about which parameters are supported, see your Nokia representative. 40 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide G-240W-G unit data sheet Table 4 Support for TR-181 parameter categories Parameter category Diagnostics Functionality Bulk data: collection, reports, HTTP, and encoding DNS IP ping TR-143 uploading and downloading IPv6 Periodic statistics Self test WiFi neighboring End user functional features Bridging port Captive portal Device information, including: processor, data model, and vendor log Device interface DHCPv4 and DCHPv6 client and server Ethernet interface Firewall Hosts Interface stack IP interface configuration End user functional features Management server NAT Neighbor discovery Optical interface PPP interface QoS classification, QoS queue, and QoS shaper Routing and route information Timing Remote access User WiFi: AP configuration, radio configuration, and SSID configuration Statistics and status monitoring Bridging statistics Device information processes WiFi radio statistics

(1 of 2) Issue: 01 3FE-47555-AAAA-TCZZA 41 G-240W-G unit data sheet 7368 ISAM ONT G-240W-G Product Guide Parameter category WiFi

(2 of 2) Functionality Access point configuration Access point associated device Radio configuration SSID configuration 4.2.11 Mobile offload support As part of the E2E solution supported by the ISAM 7750 service router, the G-240W-G ONT offers Mobile Offload support using a combination of EAP-SIM and ITU-T 802.11. EAP-SIM is an authentication method that uses the user credentials on the SIM card and EAP to authenticate the user with the Wi-Fi network, removing the need for user input (username and password). A dedicated public mobile offload SSID in the ONT enables mobile subscribers to connect to the Internet. Encryption is supported by 802.11, providing seamless Wi-Fi authentication for SIM-based user equipment. The ONT acts as the RADIUS client and sends the encapsulated EAP messages to the AAA server via the WLAN Gateway, which acts as the RADIUS proxy server. The interaction between the ONT and the AAA server provides subscriber management for authenticated mobile users without adding authentication load to the 3G network. 4.2.12 Support for soft GRE tunnels This section describes the support for soft GRE tunnels for integration with the 7750 Service Router WLAN gateway. The Nokia 7750 Service Router WLAN GW can accept soft GRE tunnels from any IP Source Address, in a preconfigured Subnet or Access Control List, or MPLS label. 4.2.12.1 GRE Generic Routing Encapsulation (GRE) is a tunneling protocol that can encapsulate a wide variety of network layer protocols inside virtual point-to-point links over an Internet Protocol network. GRE provides a secure path for transporting packets through a public network. In essence, GRE creates a private P2P connection, similar to a VPN, between clients and servers. GRE is the preferred transport mechanism between the Carrier Wi-Fi access network and the WLAN GW. 42 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide G-240W-G unit data sheet GRE works by encapsulating a payload (an inner packet that needs to be delivered to a destination network) inside an outer IP packet. GRE tunnel endpoints send payloads through GRE tunnels by routing encapsulated packets through intervening IP networks. The inner packets are not parsed along the way; only the outer IP packets are parsed as they are forwarded towards the GRE tunnel endpoint, where the GRE encapsulation is removed, and the payload is forwarded to its final destination. 4.2.12.2 Soft GRE In soft GRE, only one side of the tunnel needs to be configured; the other end learns the remote IP addresses of all remote tunnel endpoints by examining the incoming GRE packets. GRE tunnels can be automatically created when devices attach to the AP, eliminating the need for each AP to be explicitly provisioned on the WLAN Gateway. Because this soft GRE is stateless and the tunnel contexts are created based on need, the WLAN Gateway does not need to maintain states for unused tunnels, which improves scalability. The operator can restrict the traffic going through the GRE tunnel based on the SSIDs or LAN ports. Figure 9 shows the soft GRE architecture. Figure 9 Soft GRE-based architecture TR-069 VLAN: 881 Motive VSR Basic vCPE DHCP server Access Network VLAN: 100 IPTV VLAN: 981 Home Network BRG Soft-GRE Tunnel Mgmt IPTV Network Viurs scanner Security Parental Cntl Diag. Qos BW on Demand 25265 Issue: 01 3FE-47555-AAAA-TCZZA 43 G-240W-G unit data sheet 7368 ISAM ONT G-240W-G Product Guide For more information about soft GRE architecture and configuration procedures, see the 7368 Configuration, Management, and Troubleshooting guide. 4.3 G-240W-G software and installation feature support For information on installing or replacing the G-240W-G, see:

Replace a G-240W-G indoor ONT Install a G-240W-G indoor ONT For information on the following topics, see the 7368 ISAM ONT Product Overview Guide:

ONT and MDU general descriptions of features and functions Ethernet interface specifications POTS interface specifications RSSI specifications Wi-Fi specifications ONT optical budget SLID entry via Ethernet port ONT management using an ONT interface 4.4 G-240W-G interfaces and interface capacity Table 5 describes the supported interfaces and interface capacity for G-240W-G indoor ONTs. Table 5 G-240W-G indoor ONT interface connection capacity ONT type and model Maximum capacity POTS G-240W-G

(1) 2 10/ 100 BASE-T 10/ 100/ 1000 BASE-T 4 RF video

(CATV) MoCA VDSL2 E1/T1 Local craft GPON SC/APC 1 Note

(1) 44 The G-240W-G ONTs provide Wi-Fi service that is enabled and disabled using a Wi-Fi on/off switch. 4.4.1 G-240W-G connections and components Figure 10 shows the physical connections for G-240W-G indoor ONTs, 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide G-240W-G unit data sheet Figure 10 G-240W-G indoor ONT physical connections mounting Wall hole mounting Wall hole Fiber optic port Wi-Fi security buttons TEL1 TEL2 LAN1 LAN2 LAN3 LAN4 USB1 USB2 POWER WLAN RESET ON/OFF WPS LED POTS ports (2)

(RJ-11) Ethernet ports (4)

(RJ-45) USB ports (2) Power Wireless on/off button Reset button On/off button 28302 Figure 11 shows the G-240W-G ONT without the fiber cover. Issue: 01 3FE-47555-AAAA-TCZZA 45 G-240W-G unit data sheet 7368 ISAM ONT G-240W-G Product Guide Figure 11 G-240W-G ONT without fiber cover TEL1 TEL2 LAN1 LAN2 LAN3 LAN4 USB1 USB2 POWER WLAN RESET ON/OFF WPS LED Fiber optic connector

(without cover) Figure 12 shows the G-240W-G ONT with the fiber cover. Figure 12 G-240W-G ONT with fiber cover TEL1 TEL2 LAN1 LAN2 LAN3 LAN4 USB1 USB2 POWER WLAN RESET ON/OFF WPS LED Fiber optic connector

(covered) 28303 28304 46 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide G-240W-G unit data sheet Table 6 describes the physical connections for G-240W-G indoor ONTs. Table 6 G-240W-G indoor ONT physical connections Connection (1) POTS ports Ethernet ports USB ports WPS button WLAN button LED On/Off button Reset button Power input Description This connection is provided through RJ-11 ports. Up to two POTS connections are supported.The POTS ports support voice services. This connection is provided through Ethernet RJ-45 connectors. Up to four 10/100/1000 Base-T Ethernet interfaces are supported.The Ethernet ports can support both data and in-band video services on all four interfaces. This connection is provided through 2 USB ports. The ONT supports external USB hard drives that can be made accessible to all LAN devices. The Wi-Fi Protected Setup button is labeled as WPS. This button enables and disables WLAN data encryption. Wi-Fi service is compliant with IEEE 802.11 standards and is enabled and disabled using the WLAN button. This button, located on the side of the ONT, turns all LED indicators on or off. Pressing the Reset button for less than 10 seconds reboots the ONT; pressing the Reset button for 10 seconds resets the ONT to the factory defaults, except for the LOID and SLID. This connection is provided through the power connector. A power cable fitted with a barrel connector is used to make the connection. On/Off button This button turns the ONT on or off. Fiber optic port This port provides the connection for the fiber optic cable. Note

(1) The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the power connector. 4.5 G-240W-G LEDs Figure 13 shows the G-240W-G indoor ONT LEDs. Issue: 01 3FE-47555-AAAA-TCZZA 47 G-240W-G unit data sheet 7368 ISAM ONT G-240W-G Product Guide Figure 13 G-240W-G indoor ONT LEDs TEL 1 and 2 LAN 1 to 4 USB 1 and 2 Power WLAN Reset WPS LED On/Off TEL1 TEL2 LA N1 LA N2 LA N3 LA N4 U S B1 U S B2 P O W E R W PS W LA N LE D R ESET O N/O FF Table 7 provides LED descriptions for G-240W-G indoor ONTs. Table 7 G-240W-G indoor ONT LED descriptions 28310 Indicator Power Link Auth LAN 1 to 4 TEL 1 to 2 VOIP

(1 of 2) 48 LED color and behavior Green solid Red solid Off Green solid Off Off Green solid Green flashing LED behavior description Power on Light failed on startup (for example corrupt flash), or self test failed on startup, or self test failed during regular operation or when executed over OMCI Power off GPON link between ONT and OLT is operating normally GPON link is down or no link connected No fiber connected or no Rx power ONT has been configured on the OLT and is in service (UP) ONT is attempting to range with OLT ONT is ranged but not configured on OLT ONT is configured on OLT but admin is down and ONT is OOS ONT is in service and subsequently un-configured on the OLT ONT is in service while services are being configured ONT is in service but admin is down and ONT is OOS Green solid Green flashing Off Green solid Green flashing Off Green solid Off Ethernet is linked LAN activity is present (in either direction) ONT power is off or Ethernet is not connected Phone is off hook Phone is in call in or talking condition All phones are on hook VOIP service is built up and can provide service VOIP service is not built up or out of service 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide G-240W-G unit data sheet Indicator WPS WLAN USB LED color and behavior Green solid Green flashing Red solid Off Off Green solid Green flashing Green solid Green flashing Off LED behavior description WiFi protected setup link is up (negotiation and auto-configuration successful) WiFi protected setup link activity (negotiation and auto-configuration ongoing) WiFi protected setup processing exception or multiple peers using WPS simultaneously WiFi protected setup link down or no link connected (negotiation has not started or has failed) WLAN link is disabled WLAN link is enabled Traffic is passing via WLAN link At least one USB device is connected There is traffic activity on at least on USB device No USB device is connected INTERNET Green solid Green flashing Off HSI WAN is connected: a) the device has an IP address assigned from IPCP, DHCP, or static, and no traffic has been detected; b) the session is dropped due to idle timeout but the PON link is still present. PPPoE or DHCP connection in progress HSI WAN is not connected: a) there is no physical interface connection; b) the device is in bridged mode without an assigned IP address; c) the session has been dropped for reasons other than idle timeout.

(2 of 2) 4.6 G-240W-G detailed specifications Table 8 lists the physical specifications for G-240W-G indoor ONTs. Table 8 G-240W-G indoor ONT physical specifications Description Length Width Height Weight [within 0.5 lb (0.23 kg)]

(net weight of ONT) Specification 9.6 in. (244 mm) 1.4 in. (35.5 mm) 7.6 in. (192 mm) 1.23 lb (0.558 kg) Table 9 lists the power consumption specifications for G-240W-G indoor ONT. Issue: 01 3FE-47555-AAAA-TCZZA 49 G-240W-G unit data sheet 7368 ISAM ONT G-240W-G Product Guide Table 9 G-240W-G indoor ONT power consumption specifications Mnemonic G-240W-G Maximum power (Not to exceed) 19.35 W Condition 2 POTS off-hook, 4 10/100/1000 Base-T Ethernet, Wi-Fi operational Minimum power 2.33 W Condition 2 POTS on-hook, other interfaces/services not provisioned Table 10 lists the environmental specifications for G-240W-G indoor ONT. Table 10 G-240W-G indoor ONT environmental specifications Mounting method On desk or wall mounted Temperature range and humidity Altitude Operating: 23F to 113F (-5C to 45C) ambient temperature 10% to 90% relative humidity, non-condensing Storage: -4F to 158F (-20C to 70C) Contact your Nokia technical support representative for more information 4.7 G-240W-G GEM ports and T-CONTs Table 11 lists the maximum number of supported T-CONTs and GEM ports. See the appropriate release Customer Release Notes for the most accurate list of supported devices. Table 11 G-240W-G indoor ONT capacity for GEM ports and T-CONTs ONT or MDU Package P ONTs GEM ports per indoor or outdoor ONT T-CONTs per indoor or outdoor ONT Maximum Notes 124 32 124 are present; 122 are available, and 2 are reserved for multicast and debugging 32 are present; 31 are available, and 1 is reserved for OMCI 50 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide G-240W-G unit data sheet 4.8 G-240W-G performance monitoring statistics The following section identifies the supported performance monitoring statistics for G-240W-G ONTs. A check mark indicates the statistic is supported on that ONT. An empty cell indicates the statistic is not supported. The following tables are categorized by supported alarm types:

Table 12 provides statistics for ONTENET type counters Table 13 provides statistics for ONTL2UNI type counters Table 14 provides statistics for PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, and PONONTTCVOIP type counters Table 15 provides statistics for PONONTTC aggregate type counters Note If you have trouble accessing G-240W-G ONTs performance monitoring statistics using TL1, please contact your Nokia support representative for more information about how to access and retrieve performance monitoring type counters. Table 12 Package P ONTs ONTENET performance monitoring statistics ONT ONTENET statistics E S C F C E C L O B R F C S F C M T D E T M I E S C E A E R M I L T F O B T E Q S G-240W-G (1) Note

(1) A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 seconds Table 13 Package P ONTs ONTL2UNI performance monitoring statistics ONT ONTL2UNI statistics S E M A R F S E T Y B S E M A R F C M G-240W-G

(1) S M R F D P R D S D S M R F D P R D S U S E M A R F S U S E M A R F S D S E T Y B S U S E T Y B S D S E M A R F C M S U S E M A R F C M S D Issue: 01 3FE-47555-AAAA-TCZZA 51 G-240W-G unit data sheet 7368 ISAM ONT G-240W-G Product Guide Note

(1) A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 seconds Table 14 ONT G-240W-G (1) Package P ONTs PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP perfor-

mance monitoring statistics PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP statistics S K C O L B X T S G A R F X T S K C O L B X R S G A R F X R S R D H M E G D A B S G A R F T S O L Note

(1) A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 seconds Table 15 Package P ONTs PONONTTC aggregate performance monitor-

ing statistics ONT PONONTTC (aggregate) statistics S K C O L B X T S G A R F X T S K C O L B X R S G A R F X R S R D H M E G D A B S G A R F T S O L G-240W-G (1) Note

(1) A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 seconds 52 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide G-240W-G unit data sheet 4.9 G-240W-G functional blocks G-240W-G indoor ONTs are single-residence ONTs that support Wireless (Wi-Fi) service. Wi-Fi service on these ONTs is compliant with the IEEE 802.11 standard and enabled or disabled using a WLAN button. In addition to the Wi-Fi service, these ONTs transmit Ethernet packets to four RJ-45 Ethernet ports and voice traffic to two RJ-11 POTS ports. These ONTs also feature fiber optic, USB, and power connectors. Figure 14 shows the functional blocks for G-240W-G indoor ONT. Figure 14 Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS and without RF video NAND FLASH DDR3 I2C EEPROM SOC USB I2C/RX/TX_SD,TX_PD SerDes LED_CLK/DAT 2*USB 2.0 BOB Shift Register LED PCIE0 PCIE1 WIFI 11b/g/n WIFI 11ac RD/

Antenna 2x2 11b/g/n RD/

Antenna 3x3 11ac GE0 GE1 GE2 GE3 SLIC Transform Protection 4*RJ-45 2*RJ-11 ONT SoC technology serves as the main hardware block for these ONTs; see Figure 15. 28301 Issue: 01 3FE-47555-AAAA-TCZZA 53 G-240W-G unit data sheet 7368 ISAM ONT G-240W-G Product Guide Figure 15 G-240W-G ONT hardware block POTS ports Control processor SoC DSP SoC Bridge Ethernet MACs GPON MAC Ethernet ports GPON 19421 ONT SoC technology consists of five key elements:

GPON MAC The Gigabit Passive Optical Network Media Access Control (GPON MAC) element on the SoC terminates the GPON interface using an optical diplexer. This interface supports GPON as described in G.984.3 (GPON TC Layer) ITU specification. Ethernet MAC The SoC provides up to four GE MACs. DSP interface The Digital Signal Processor (DSP) provides voice processing for 2 POTS lines with 3-way calling. The DSP has a dedicated 64 kbyte instruction cache and shares a 32 kbyte data cache with the Control Processor. It provides up to 4 network processor cores, each at 800MHz. Control Processor The Control Processor features an integral memory management unit that supports a dedicated 64 kbyte instruction cache and shares a single 32 kbyte data cache with the DSP. The Control Processor and DSP also include a single channel Data Management Application (DMA) controller with a 4 kbyte read ahead low-latency Dynamic Random Access Memory (DRAM) access port. Switch matrix The Switch matrix provides an integrated data channel between the four GE MACs, the GPON MAC, the DSP, the control processor, and the other integrated elements such as flash memory, DRAM, and the local bus controller. 54 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide G-240W-G unit data sheet These ONTs can also interact with additional hardware components to support functionality not provided by the SoC technology. 4.10 G-240W-G standards compliance G-240W-G indoor ONTs are compliant with the following standards:

802.1p marking and VLAN based pbit is supported EN 300-328 v1.9.1 wide band data transmission standards for 2.4GHz bands G.711 support for FAX and modem connection G.984 support GPON interface (framing) G.984.2 support for Amd1, class B+

G.984.3 support for activation and password functions G.984.3 support for AES with operator enable/disable on per port-ID level G.984.3 support for FEC in both upstream and downstream directions G.984.3 support for multicast using a single GEM Port-ID for all video traffic G984.4 and G.983.2 support for ONT management and provisioning CE marking for European standards for health, safety, and environmental protection FCC marking for US standards for health, safety, and environmental protection 4.10.1 Energy-related products standby and off modes compliance Hereby, Nokia declares that the G-240W-G ONTs are in compliance with the essential requirements and other relevant provisions of Directive 2009/125/EC together with Commission Regulation (EC) No 1275/2008 and Commission Regulation (EC) No 801/2013. The G-240W-G ONTS qualify as equipment with high network availability (HiNA) functionality. Since the main purpose of G-240W-G ONTs is to provide network functionality with HiNA 7 days /24 hours, the modes Off/Standby, Power Management, and Networked Standby are inappropriate. For information about the type and number of network ports, see G-240W-G interfaces and interface capacity in this chapter. For information about power consumption, see G-240W-G detailed specifications in this chapter. Issue: 01 3FE-47555-AAAA-TCZZA 55 G-240W-G unit data sheet 7368 ISAM ONT G-240W-G Product Guide 4.10.2 FCC statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 4.10.3 FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 4.11 G-240W-G special considerations G-240W-G is a package P ONT. 56 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide G-240W-G unit data sheet 4.11.1 Wi-Fi service G-240W-G indoor ONTs feature Wi-Fi service as well as voice and data services. Wi-Fi is a wireless networking technology that uses radio waves to provide wireless HSI and network connections. This ONT complies with the IEEE 802.11 standards, which the Wi-Fi Alliance defines as the basis for Wi-Fi technology. 4.11.1.1 Wi-Fi physical features G-240W-G indoor ONTs have the following physical features that assist in providing Wi-Fi service:

WLAN button for enabling and disabling Wi-Fi service 5 internal antennas: 2 for 2.4G and 3 for 5G one Wi-Fi Protected Setup (WPS) push button for both 2.4G and 5G controlling 4.11.1.2 Wi-Fi standards and certifications The Wi-Fi service on G-240W-G indoor ONTs supports the following IEEE standards and Wi-Fi Alliance certifications:

certified for IEEE 802.11ac/b/g/n/standards WPA support including WPA-PSK certified for WPA2-Personal and WPA2-Enterprise 4.11.1.3 Wi-Fi GUI features G-240W-G indoor ONTs have HTML-based Wi-Fi configuration GUIs. 4.11.2 G-240W-G ONT considerations and limitations Table 16 lists the considerations and limitations for Package P G-240W-G ONTs. Table 16 G-240W-G ONT considerations and limitations Considerations and limitations Call History Data collection (ONTCALLHST) is supported, except for the following parameters:

RTP packets (discarded), far-end RTCP and RTCP-XR participation, RTCP average and peak round trip delay, MOS, average jitter, number of jitter-buffer over-runs and under runs.

(1 of 2) Issue: 01 3FE-47555-AAAA-TCZZA 57 G-240W-G unit data sheet 7368 ISAM ONT G-240W-G Product Guide Considerations and limitations Some voice features are configurable on a per ONT basis, including Call Waiting, Call Hold, 3-Way Calling, and Call Transfer. The following voice features / GSIP parameters are configurable on a per-Client/ per-ONT basis (not per-Subscriber):

Enable Caller ID and Enable Caller Name ID Digitmap and the associated Interdigit and Critical timers and Enter key parameters Warmline timer is enabled per subscriber, but the warmline timer value is configured per ONT and must Miscellaneous timers: Permanent, Timed-release, Reanswer, Error-tone, and CW-alert timers Service Codes for the following features: CCW, Call Hold and Warmline

(2 of 2) Features / functions: Message waiting mode, WMWI refresh interval, DTMF volume level have a lower value than the Permanent time 58 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Install a G-240W-G indoor ONT 5 Install a G-240W-G indoor ONT 5.1 Purpose 5.2 General 5.3 Prerequisites 5.4 Recommended tools 5.5 Safety information 5.6 Procedure 5.1 Purpose This chapter provides the steps to install a G-240W-G indoor ONT. 5.2 General The steps listed in this chapter describe mounting and cabling for G-240W-G indoor ONTs. 5.3 Prerequisites You need the following items before beginning the installation:

all required cables 5.4 Recommended tools You need the following tools for the installation:

#2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter fiber optic splicing tools Issue: 01 3FE-47555-AAAA-TCZZA 59 Install a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide drill and drill bits paper clip 5.5 Safety information Read the following safety information before installing the unit. Danger 1 Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits. Danger 2 Make sure all sources of power are turned off and have no live voltages present on feed lines or terminals. Use a voltmeter to measure for voltage before proceeding. Danger 3 Always contact the local utility company before connecting the enclosure to the utilities. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Note 1 Observe the local and national laws and regulations that may be applicable to this installation. Note 2 Observe the following:

The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See the detailed specifications in the G-240W-G unit data sheet for the temperature ranges for these ONTs. 60 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Install a G-240W-G indoor ONT 5.6 Procedure Use this procedure to install a G-240W-G indoor ONT. 1 Place the indoor ONT unit:

a On the flat surface, such as a desk; go to step 3. Note The G-240W-G cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are:

allow a minimum 100 mm clearance above the top cover allow a minimum 50 mm clearance from the side vents do not place any heat source directly above the top cover or below the bottom cover b On a wall, go to step 2. 2 Mount the G-240W-G indoor ONT on a wall. The G-240W-G indoor ONT must be mounted in a horizontal position, as indicated by the wall mounting key holes in Figure 16. If possible, mount the ONT on a wall stud. Figure 16 shows the ONT with the connections and the key mounting holes. Issue: 01 3FE-47555-AAAA-TCZZA 61 Install a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Figure 16 G-240W-G ONT with connections and key mounting holes mounting Wall hole mounting Wall hole Fiber optic port Wi-Fi security buttons TEL1 TEL2 LAN1 LAN2 LAN3 LAN4 USB1 USB2 POWER WLAN RESET ON/OFF WPS LED POTS ports (2)

(RJ-11) Ethernet ports (4)

(RJ-45) USB ports (2) Power Wireless on/off button Reset button On/off button 28302 i ii Attach the wall mounting keyholes on the ONT. Attach the ONT to the wall. Review the connection locations, as shown in Figure 16. Connect the Ethernet cables to the RJ-45 ports; see Figure 16 for the location of the RJ-45 ports. Route the POTS cables directly to the RJ-11 ports as per local practices. The POTS port to the left is labeled 1 for Line 1 while the port on the right is labeled 2 for Line 2, as shown in Figure 16. 3 4 5 62 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Install a G-240W-G indoor ONT 6 Connect the fiber optic cable with SC/APC adapter into the SC/APC connector; see Figure 16 for the location of the SC/APC connector. Danger Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. Warning Be careful to maintain a bend radius of no less than 1.5 in.

(3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. Note Fiber cable preparation varies depending on the type and size of the inside or outside plant fiber cable being spliced to the SC/APC fiber optic pigtail cable. 7 Install the power supply according to manufacturer specifications. Note Observe the following:

Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12VDC, 3A. 8 9 Connect the power cable to the power connector. Power up the ONT unit by using the power switch. 10 If used, enable the Wi-Fi service. i ii Locate the WLAN button on the ONT; see Figure 16 for location of the WLAN button. Press the WLAN button to change the status of the Wi-Fi service. 11 Verify the ONT LEDs, voltage status, and optical signal levels; see the 7368 Hardware and Cabling Installation Guide. 12 Activate and test the services; see the 7368 Hardware and Cabling Installation Guide. 13 If used, configure the SLID; see the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide. Issue: 01 3FE-47555-AAAA-TCZZA 63 Install a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide 14 If necessary, reset the ONT. i ii Locate the Reset button on a G-240W-G indoor ONT as shown in Figure 16. Insert the end of a straightened paper clip or other narrow object into the hole in the Reset button to reset the ONT. 15 STOP. This procedure is complete. 64 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Replace a G-240W-G indoor ONT 6 Replace a G-240W-G indoor ONT 6.1 Purpose 6.2 General 6.3 Prerequisites 6.4 Recommended tools 6.5 Safety information 6.6 Procedure 6.1 Purpose This chapter provides the steps to replace G-240W-G indoor ONTs. 6.2 General The steps listed in this chapter describe mounting and cabling for G-240W-G indoor ONTs. 6.3 Prerequisites You need the following items before beginning the installation:

all required cables 6.4 Recommended tools You need the following tools for replacing the ONT:

#2 Phillips screwdriver 1/4 in. (6 mm) flat blade screwdriver wire strippers RJ-45 cable plug crimp tool voltmeter or multimeter fiber optic splicing tools Issue: 01 3FE-47555-AAAA-TCZZA 65 Replace a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide optical power meter drill and drill bits 6.5 Safety information Read the following safety information before replacing the unit. Danger 1 Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits. Danger 2 Make sure all sources of power are turned off and have no live voltages present on feed lines or terminals. Use a voltmeter to measure for voltage before proceeding. Danger 3 Always contact the local utility company before connecting the enclosure to the utilities. Warning This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT. Caution Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit. Note 1 Observe the local and national laws and regulations that may be applicable to this installation. Note 2 Observe the following:

The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. The indoor ONT must be installed by qualified service personnel. Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use. See the detailed specifications in the G-240W-G unit data sheet for the ONT temperature ranges for these ONTs. 66 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Replace a G-240W-G indoor ONT 6.6 Procedure Use this procedure to replace a G-240W-G indoor ONT. 1 Deactivate the ONT services at the P-OLT. If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). i Use the RTRV-ONT command to verify the ONT status and th associated services. Record the serial number or the SLID of the ONT displayed in the command output. Example:

RTRV-ONT::ONT-1-1-1-1-1;

ii If the ONT is in service, place the ONT in OOS state. Example:

ED-ONT::ONT-1-1-1-1-1;

2 If used, disable the Wi-Fi service by pressing the WLAN button; see Figure 17 for the location of the WLAN button. Figure 17 G-240W-G indoor ONT connections mounting Wall hole mounting Wall hole Fiber optic port Wi-Fi security buttons TEL1 TEL2 LAN1 LAN2 LAN3 LAN4 USB1 USB2 POWER WLAN RESET ON/OFF WPS LED POTS ports (2)

(RJ-11) Ethernet ports (4)

(RJ-45) USB ports (2) Power Wireless on/off button Reset button On/off button 28302 Issue: 01 3FE-47555-AAAA-TCZZA 67 Replace a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide 3 4 5 Power down the unit by using the on/off power switch. Disconnect the POTS, Ethernet, and power cables from the ONT; see Figure 17 for the connector locations on the G-240W-G indoor ONT. Disconnect the fiber optic cables. Danger Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. i ii Unplug the fiber optic cable with SC/APC connector from the ONT; see Figure 17 for the location of the fiber optic port. Attach a fiber dust cover to the end of the SC/APC connector. 6 Replace the ONT with a new unit:

a b On a flat surface, such as a desk, substitute the new ONT for the old ONT on a flat surface, horizontally resting on its four feet. On a wall. i ii iii Remove the old ONT from the wall. Attach the wall mount adapter bracket (shipped with the ONT) to the two wall mounting key holes on the new ONT. Attach the new ONT to the wall. 7 8 9 Connect the Ethernet cables directly to the RJ-45 ports; see Figure 17 for the location of the RJ-45 ports. Connect the POTS cables directly to the RJ-11 ports as per local practices; see Figure 17 for the location of the RJ-11 ports. The RJ-11 port to the left is labeled 1 for Line 1 while the port on the right is labeled 2 for Line 2. If required, have approved service personnel who are trained to work with optic fiber clean the fiber optic connection. See the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide for more information about fiber optic handling, inspection, and cleaning. Danger Fiber optic cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. 68 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Replace a G-240W-G indoor ONT 10 Connect the fiber optic cable with SC/APC adapter into the SC/APC connector. Figure 17 shows the location of the SC/APC connector. Danger Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. Warning Be careful to maintain a bend radius of no less than 1.5 in.

(3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber. Note Fiber cable preparation varies depending on the type and size of the inside or outside plant fiber cable being spliced to the SC/APC fiber optic pigtail cable. 11 Install the power supply according to manufacturer specifications. Note Observe the following:

Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 VDC, 3 A. 12 Connect the power cable to the power connector. 13 Power up the unit by using the power switch. 14 15 If used, enable the Wi-Fi service by pressing the WLAN button; see Figure 17 for the location of the WLAN button. If used, configure the SLID; see the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide for more information. Note A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager. If the old SLID is used, no changes need to be made at the P-OLT; see the operations and maintenance documentation for the OLT for more details. 16 Verify the ONT LEDs, voltage status, and optical signal levels; see the 7368 Hardware and Cabling Installation Guide. 17 Activate and test the services; see the 7368 Hardware and Cabling Installation Guide. Issue: 01 3FE-47555-AAAA-TCZZA 69 Replace a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide 18 If necessary, reset the ONT. i ii Locate the Reset button on a G-240W-G indoor ONT as shown in Figure 17. Insert the end of a straightened paper clip or other narrow object into the hole in the Reset button to reset the ONT. 19 STOP. This procedure is complete. 70 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT 7 Configure a G-240W-G indoor ONT 7.1 General 7.2 HGU mode GUI configuration 7.3 SFU mode configuration 7.1 General Please refer to the configuration information provided with your OLT for the software configuration procedure for a G-240W-G ONT. For HTTP configuration procedures, please refer to the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide. 7.2 HGU mode GUI configuration Use the procedures below to use the web-based GUI for the G-240W-G in HGU mode. This mode is preset at delivery. A home gateway unit (HGU) is a home networking device, used as a gateway to connect devices in the home through fiber to the Internet. An HGU provides a variety of features for the home network including routing and firewall capability. By using the HGU, users can connect all smart equipment in their home, including personal computers, set-top boxes, mobile phones, and other consumer electronics devices, to the Internet. 7.2.1 Login Use the procedure below to login to the web-based GUI for the G-240W-G. Procedure 6 Login to web-based GUI 1 Open a web browser and enter the IP address of the ONT in the address bar. The login window appears. The default gateway IP address is http://192.168.1.254. You can connect to this IP address using your web browser after connecting your PC to one of Ethernet ports of the ONT. The static IP address of your PC must be in the same 192.168.1.x subnet as the ONT. Issue: 01 3FE-47555-AAAA-TCZZA 71 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide 2 Enter your username and password in the Log in window, as shown in Figure 18. The default user name is userAdmin. The default password is a random number, which is included in the ONT kit. Figure 18 Web login window Caution Pressing the Reset button for less than 10 seconds reboots the ONT; pressing the Reset button for 10 seconds resets the ONT to the factory defaults, except for the LOID and SLID. Note If you forget the current username and password, press the reset button for 5 s and the default values for the username and password will be recovered at startup. 3 Click Login. The Device Information screen appears. Note To help protect the security of your Internet connection, the application displays a pop-up reminder to change both the Wi-Fi password and the ONT password. To increase password security, use a minimum of 10 characters, consisting of a mix of numbers and upper and lower case letters. 4 STOP. This procedure is complete. 7.2.2 Device and connection status G-240W-G ONTs support the retrieval of a variety of device and connection information, including:

device information LAN status WAN status 72 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT WAN status IPv6 Home networking information optics module status statistics retrieval voice information Procedure 7 Device information retrieval 1 Select Status > Device Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 19. Figure 19 Device Information window Note Upon login, the GPON Home Gateway window displays the WAN status block on the bottom left part of each window. This block shows the WAN connection ID, the WAN status, and any WAN errors. This block is accurate upon login, but it is static; click the Refresh button to update the information. Table 17 describes the fields in the Device Information window. Table 17 Device Information parameters Field Device Name Vendor

(1 of 2) Description Name on the ONT Name of the vendor Issue: 01 3FE-47555-AAAA-TCZZA 73 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Field Serial Number Description Serial number of the ONT Hardware version Hardware version of the ONT Boot version Boot version of the ONT Software version Software version of the ONT Chipset Lot Number Chipset of the ONT Production date of the ONT Device Running Time Amount of time the device has run since last reset in hours, minutes, and seconds

(2 of 2) 2 3 Click Refresh to update the displayed information. STOP. This procedure is complete. 74 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Procedure 8 LAN status retrieval 1 Select Status > LAN Status from the top-level menu in the GPON Home Gateway window, as shown in Figure 20. Figure 20 LAN status window Table 18 describes the fields in the LAN status window. Table 18 LAN status parameters Field Wireless Information Wireless Status Wireless Channel SSID Name Description Indicates whether the wireless is on or off Wireless channel number Name of each SSID Wireless Encryption Status Encryption type used on the wireless connection Wireless Rx Packets Wireless Tx Packets Wireless Rx Bytes Wireless Tx Bytes

(1 of 2) Number of packets received on the wireless connection Number of packets transmitted on the wireless connection Number of bytes received on the wireless connection Number of bytes transmitted on the wireless connection Issue: 01 3FE-47555-AAAA-TCZZA 75 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Field Power Transmission (mW) Ethernet Information Ethernet Status Description Power of the wireless transmission, in mW Indicates whether the Ethernet connection is on or off Ethernet IP Address IP address of the Ethernet connection Ethernet Subnet Mask Subnet Mask of the Ethernet connection Ethernet MAC Address MAC address of the Ethernet connection Ethernet Rx Packets Ethernet Tx Packets Ethernet Rx Bytes Ethernet Tx Bytes

(2 of 2) Number of packets received on the Ethernet connection Number of packets transmitted on the Ethernet connection Number of bytes received on the Ethernet connection Number of bytes transmitted on the Ethernet connection 2 3 Click Refresh to update the displayed information. STOP. This procedure is complete. 76 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Procedure 9 WAN status retrieval 1 Select Status > WAN Status from the top-level menu in the GPON Home Gateway window, as shown in Figure 21. Figure 21 WAN status window Table 19 describes the fields in the WAN status window. Table 19 WAN status parameters Field WAN connection list Access Type Connection Mode Enable/Disable VLAN Description Drop-down menu listing all WAN connections. The connection shown is the connection for which WAN status will be shown. Connection mode of the WAN connection Select this checkbox to enable the WAN connection VLAN ID WAN Link Status Whether the WAN link is up or down BRAS Connection Status Whether the BRAS connection is connecting or disconnected PON Link Status Whether the PON link is up or down Tx Packets Rx Packets

(1 of 2) Number of packets transmitted on the WAN connection Number of packets received on the WAN connection Issue: 01 3FE-47555-AAAA-TCZZA 77 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Field Tx Dropped Rx Dropped Err Packets

(2 of 2) Description Number of packets dropped on the transmit WAN connection Number of packets dropped on the receive WAN connection Number of errored packets on the WAN connection 2 3 Click Refresh to update the displayed information. STOP. This procedure is complete. Procedure 10 WAN status IPv6 retrieval 1 Select Status > WAN Status IPv6 from the top-level menu in the GPON Home Gateway window, as shown in Figure 22. Figure 22 WAN status IPv6 window Table 20 describes the fields in the WAN status IPv6 window. 78 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Table 20 WAN status IPv6 parameters Field WAN connection list Description Drop-down menu listing all WAN connections. The connection shown is the connection for which WAN status will be shown. Enable/Disable Select this checkbox to enable the WAN connection VLAN WAN Link Status PON Link Status Tx Packets Rx Packets Tx Dropped Rx Dropped Err Packets Auto Configure IPv6 address IPv6 Prefix IPv6 Gateway Netmask Gateway Primary DNS Second DNS VLAN ID Whether the WAN link is up or down Whether the PON link is up or down Number of packets transmitted on the WAN connection Number of packets received on the WAN connection Number of packets dropped on the transmit WAN connection Number of packets dropped on the receive WAN connection Number of errored packets on the WAN connection IPv6 address that identifies the device and its location IPv6 prefix IPv6 gateway address Network mask Gateway address Primary Domain Name Server Secondary Domain Name Server 2 3 Click Refresh to update the displayed information. STOP. This procedure is complete. Issue: 01 3FE-47555-AAAA-TCZZA 79 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Procedure 11 Home networking information retrieval 1 Select Status > Home Networking from the top-level menu in the GPON Home Gateway window, as shown in Figure 23. Figure 23 Home networking information window Table 21 describes the fields in the Home networking window. Table 21 Home networking parameters Field Local Interface Ethernet Description Table displays the number of Ethernet connections and their settings Wireless (2.4GHz) Table displays the number of wireless connections and their settings Wireless (5GHz) Wireless Settings (2.4GHz) Network Name Name of the wireless network Hexadecimal address of the wireless access point Access Point Wireless Settings (5GHz) Network Name Name of the wireless network

(1 of 2) 80 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Field Access Point Local Devices Table entry

(2 of 2) Description Hexadecimal address of the wireless access point Each entry indicates the status (active or inactive), connection type, device name, IP address, hardware address, and IP address allocation of each connected local device. 2 3 4 Click Delete to delete a particular local device connection. Click Refresh to update the displayed information. STOP. This procedure is complete. Procedure 12 Optics module status retrieval 1 Select Status > Optics Module Status from the top-level menu in the GPON Home Gateway window, as shown in Figure 24. Figure 24 Optics module status window Table 22 describes the fields in the Optics module status window. Issue: 01 3FE-47555-AAAA-TCZZA 81 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Table 22 Optics module status parameters Field Laser Bias Current (ONT ANI-ONT-Side Optical Measurements) Optics Module Voltage (ONT ANI-ONT-Side Optical Measurements) Optics Module Temperature (ONT ANI-ONT-Side Optical Measurements) Description Laser bias current, measured in uA Optics module voltage, measured in V Optics module temperature, measured in C Rx Optics Signal Level at 1490 nm (ONT ANI-ONT-Side Optical Measurements) Received optics signal level at 1490 nm, measured in dBm Tx Optics Signal Level at 1310 nm (ONT ANI-ONT-Side Optical Measurements) Transmitted optics signal level at 1310 nm, measured in dBm Lower (ONT ANI-ONT-Side Optical Measurements-Optical Threshold) Upper (ONT ANI-ONT-Side Optical Measurements-Optical Threshold) Lower optical threshold, measured in dBm Upper optical threshold, measured in dBm 2 3 Click Refresh to update the displayed information. STOP. This procedure is complete. Procedure 13 Statistics retrieval 1 Select Status > Statistics from the top-level menu in the GPON Home Gateway window. Statistics are available for LAN ports, WAN ports, and WLAN ports. Figure 25 shows the statistics for the LAN ports. 82 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Figure 25 LAN ports Statistics window Figure 26 shows the statistics for the WAN ports. Issue: 01 3FE-47555-AAAA-TCZZA 83 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Figure 26 WAN ports statistics window If there are no WAN connections to display, the system displays a message, as shown in Figure 27. 84 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Figure 27 WAN ports statistics message Figure 28 shows the statistics for the WLAN ports. Issue: 01 3FE-47555-AAAA-TCZZA 85 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Figure 28 WLAN ports statistics window If there are no WLAN connections to display, the system displays a message, as shown in Figure 29. 86 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Figure 29 WLAN ports statistics message 2 STOP. This procedure is complete. Issue: 01 3FE-47555-AAAA-TCZZA 87 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Procedure 14 Voice information retrieval 1 Select Status > Voice Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 30. Figure 30 Voice Information window Table 23 describes the fields in the Voice Information window. Table 23 Voice Information parameters Field Line Line Status Soft Switch(1) Phone Number(1)

(1 of 2) Description Choose a line from the drop-down menu. The default is Line 1. Depending on the line chosen, the line options are:

Up Initializing Registering Unregistering Error Testing Quiescent Disabled The default is Disabled Proxy IP address; blank if the line is not registered Phone number configured for a telephone line 1;

+13290611266 88 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Field Register Status Register Error Code Register Error Reason User Agent IP

(2 of 2) Description The default is Registered Blank if no voice service is provisioned SIP standard error code for the register status; for example, 401, 403, 503 This field is blank if the register is set to OK SIP standard error reason for the register status This field is blank if the register is set to OK IP address of the user agent ExternalIPAddress in WANIPConnection or WANPPPConnection Note

(1) 2 3 This field is only visible at the adminGPON level; it is not visible at the userAdmin level. Click Refresh to update the displayed information. STOP. This procedure is complete. 7.2.3 Network configuration G-240W-G ONTs also support network configuration, including:

LAN LAN IPv6 WAN WAN DHCP WiFi 2.4G WiFi 5G Wireless schedule Routing DNS TR-069 GRE tunnel QoS US (upstream) classification Issue: 01 3FE-47555-AAAA-TCZZA 89 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Procedure 15 LAN networking configuration 1 Select Network > LAN from the top-level menu in the GPON Home Gateway window, as shown in Figure 31. Figure 31 LAN network window Table 24 describes the fields in the LAN network window. Table 24 LAN network parameters Field Port Mode All Ports to Bridge Mode Port 1 - 4 IPv4 Address Subnet Mask DHCP Enable Description Select this checkbox to set all ports to Bridge mode Drop-down port mode for each port: Route mode or Bridge mode IP Address of the ONT Subnet mask of the ONT Select this checkbox to enable DHCP DHCP Start IP Address Starting DHCP IP address

(1 of 2) 90 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Field DHCP End IP Address DHCP Lease Time Primary DNS Secondary DNS Static DHCP Entry MAC Address IPv4 Address

(2 of 2) Description Ending DHCP IP address DHCP lease time (in min) Primary DNS identifier Secondary DNS identifier MAC address for the static DHCP IPv4 address for the static DHCP 2 3 4 5 6 7 8 Select the mode for each port. Click Save. Enter the DHCP configuration information. Click Save. Enter the Static DHCP information. Click Add. You can also use this panel to delete a Static DHCP MAC address or IPv4 address. STOP. This procedure is complete. Issue: 01 3FE-47555-AAAA-TCZZA 91 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Procedure 16 LAN IPv6 networking configuration 1 Select Network > LAN_IPv6 from the top-level menu in the GPON Home Gateway window, as shown in Figure 32. Figure 32 LAN IPv6 network window Table 25 describes the fields in the LAN IPv6 network window. Table 25 LAN IPv6 network parameters Field IPv6 LAN Host Configuration DNS Server Description Choose a DNS server from the drop-down menu. Interface LAN Prefix Enable

(1 of 2) This field appears if you selected the Wan Connection option for the prefix config field. Choose a WAN connection interface from the drop-down menu. This field appears if you selected the Static option for the prefix config field. Type a connection. Select this checkbox to enable the LAN connection 92 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Field Prefix Config Description Choose a prefix config option from the drop-down menu, either WANConnection (prefix will be obtained from the WAN) or Static (enables you to enter the prefix). WAN Interface Choose a WAN interface from the drop-down menu WAN Prefix DHCPv6 Server Enable DHCPv6 Server Pool LAN Prefix RouterAdvertisement LAN Prefix Whether the address info through DCHP Whether other info obtained through DHCP Maximum interval for periodic RA messages Minimum interval for periodic RA messages

(2 of 2) Choose a WAN prefix from the drop-down menu Select this checkbox to enable the DHCPv6 Server connection This field appears if you selected the Static option for the prefix config field. Type a connection. This field appears if you selected the Static option for the prefix config field. Type a connection. Select this checkbox to enable address information retrieval through DHCP. Select this checkbox to enable retrieval of other information through DHCP. Enter the maximum interval (in seconds) for periodic Router Advertisement messages. The interval range is from 4 to 1800. Enter the minimum interval (in seconds) for periodic Router Advertisement messages. The interval range is from 4 to 1800. 2 3 4 5 6 Choose a DNS server, prefix config, and interface. Select or enter the DHCP configuration information. Enter the maximum and minimum intervals for RA messages. Click Save/Apply. STOP. This procedure is complete. Issue: 01 3FE-47555-AAAA-TCZZA 93 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Procedure 17 WAN networking configuration 1 Select Network > WAN from the top-level menu in the GPON Home Gateway window, as shown in Figure 33. Figure 33 WAN network window Table 26 describes the fields in the WAN network window. Table 26 WAN network parameters Field WAN Connection List Description Choose a WAN connection from the drop-down menu to set the connection parameters Connection Type Choose a connection type: IPoE or PPPoE IP mode Choose an IP mode from the drop-down menu: IPv4 or IPv6 Enable/Disable Select this checkbox to enable the WAN connection

(1 of 2) 94 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Field NAT Service Description Select this checkbox to enable NAT Select the checkboxes to enable service types for this connection Enable VLAN Select this checkbox to enable VLAN VLAN ID VLAN PRI Enter the VLAN ID Enter the VLAN PRI WAN IP Mode Choose an IP mode from the drop-down menu Connection Type Choose a connection type from the drop-down menu Enter the username Enter the password Enter the Keep Alive Time (from 5 to 60 seconds) The number of keep alive time retires (1 to 10); this field cannot be modified in regular user mode The echo value: the keep alive time value multiplied by the number of retries; this field cannot be modified in regular user mode Username Password Keep Alive Time Keep Alive Retry Echo Value DHCPv6 Enable Request Address Request Prefix Request Option Auto Configured Enable

(2 of 2) 2 3 4 Configure a specific WAN connection. Click Save. STOP. This procedure is complete. Issue: 01 3FE-47555-AAAA-TCZZA 95 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Procedure 18 WAN DHCP configuration 1 Select Network > WAN DHCP from the top-level menu in the GPON Home Gateway window, as shown in Figure 34. Figure 34 WAN DHCP window Table 27 describes the fields in the WAN DHCP window. Table 27 WAN DHCP parameters Field WAN Connection List DHCP Option 50 Persistent Description Choose a WAN connection from the drop-down menu Select this checkbox to enable DHCP Option 50 persistent Enable DHCP Option 60 Select this checkbox to enable DHCP Option 60 (vendor class identifier) Enable DHCP Option 61 Select this checkbox to enable DHCP Option 61 (client identifier) Enable DHCP Option 77 Select this checkbox to enable DHCP Option 77 Enable DHCP Option 90 Select this checkbox to enable DHCP Option 90 2 Configure a WAN DHCP option. 96 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT 3 4 Click Save. STOP. This procedure is complete. Procedure 19 WiFi 2.4G networking configuration 1 Select Network > WiFi 2.4G from the top-level menu in the GPON Home Gateway window, as shown in Figure 35. Figure 35 WiFi 2.4G network window Table 28 describes the fields in the WiFi 2.4G network window. Table 28 WiFi 2.4G network parameters Field Enable

(1 of 3) Description Select this checkbox to enable WiFi Issue: 01 3FE-47555-AAAA-TCZZA 97 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Field Mode Bandwidth Channel Transmitting Power WMM Total MAX Users SSID Configuration SSID Select SSID Name Enable SSID auto (b/g/n) b g n b/g Description Choose a Wi-Fi mode from the drop-down menu:

Choose from:

Choose a channel from the drop-down menu or choose Auto to have the channel automatically assigned 20 MHz 40 MHz 20/40 MHz Choose a percentage for the transmitting power from the drop-down menu:

Low (25%) Medium (50%) High (75%) Maximum (100%) Choose Enable or Disable from the drop-down menu to enable or disable WiFi multi-media Enter the number of total MAX users Choose the SSID from the drop-down menu Enter the SSID name Enable or disable SSID from this drop-down menu SSID Broadcast Enable or disable SSID broadcast from this drop-down menu MAX Users Enter the number of MAX users Encryption Mode WPA Version WPA Encryption Mode WPA Key Enable WPS

(2 of 3) Choose an encryption mode from the drop-down menu:

OPEN WEP WPA/WPA2 Personal WPA/WPA2 Enterprise (1) (2) Choose a WPA version from the drop-down menu:

WPA1 WPA2 WPA1/WPA2 Choose a WPA encryption mode from the drop-down menu:

TKIP AES Enter the WPA key TKIP/AES Enable or disable WPS from this drop-down menu 98 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Field WPS Mode

(3 of 3) Description Choose a WPS mode from the drop-down menu: PBC (Push Button Connect) or PIN

(Personal Identification Number) Notes

(1) When Encryption Mode is set to WPA/WPA2 Enterprise, the following options are no longer available: WPA version, WPA encryption mode, WPA key, Enable WPS, WPS mode.

(2) When Encryption Mode is set to WPA/WPA2 Enterprise, the following options become available: Primary RADIUS server, port and password; Secondary RADIUS server, port, and password; RADIUS accounting port. 2 3 4 5 Configure the WiFi connection. If you have enabled and configured WPS, click WPS connect. Click Save. STOP. This procedure is complete. Issue: 01 3FE-47555-AAAA-TCZZA 99 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Procedure 20 WiFi 5G networking configuration 1 Select Network > WiFi 5G from the top-level menu in the GPON Home Gateway window, as shown in Figure 36. Figure 36 WiFi 5G network window Table 29 describes the fields in the WiFi 5G network window. Table 29 WiFi 5G network parameters Field Enable Bandwidth Channel

(1 of 2) Description Select this checkbox to enable WiFi 20 MHz 40 MHz 80 MHz Choose from:

Choose a channel from the drop-down menu or choose Auto to have the channel automatically assigned 100 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Field Transmitting Power WMM Enable MU-MIMO Description Choose a percentage for the transmitting power from the drop-down menu:

Low (20%) Medium (40%) High (60%) Maximum (100%) Choose Enable or Disable from the drop-down menu to enable or disable WiFi multi-media Choose Enable or disable MU-MIMO from this drop-down menu The default is Enable, which enables users and wireless terminals to communicate with each other. MU-MIMO may decrease Wi-Fi performance for clients who do not support it, in which case Nokia recommends that you choose Disable. Total MAX Users Enter the total number of MAX users DFS re-entry Choose Enable or Disable from the drop-down menu to enable or disable DFS re-entry SSID Configuration SSID Select SSID Name Enable SSID Choose the SSID from the drop-down menu Change the name of the selected SSID Choose Enable or disable SSID from this drop-down menu SSID Broadcast Choose Enable or disable SSID broadcast from this drop-down menu MAX Users Enter the number of MAX users Encryption Mode WPA Key Enable WPS WPS Mode

(2 of 2) Choose an encryption mode from the drop-down menu:

OPEN WEP WPA/WPA2 Personal WPA/WPA2 Enterprise (1) (2) Enter the WPA key Choose Enable or disable WPS from this drop-down menu Choose a WPS mode from the drop-down menu: PBC (Push Button Connect) or PIN (Personal Identification Number) Notes

(1) When Encryption Mode is set to WPA/WPA2 Enterprise, the following options are no longer available: WPA version, WPA encryption mode, WPA key, Enable WPS, WPS mode.

(2) When Encryption Mode is set to WPA/WPA2 Enterprise, the following options become available: Primary RADIUS server, port and password; Secondary RADIUS server, port, and password; RADIUS accounting port. 2 3 Configure the WiFi connection. If you have enabled and configured WPS, click WPS connect. Issue: 01 3FE-47555-AAAA-TCZZA 101 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide 4 5 Click Save. STOP. This procedure is complete. Procedure 21 Wireless scheduling 1 Select Network > Wireless Schedule from the top-level menu in the GPON Gateway window, as shown in Figure 37. Figure 37 Wireless Schedule window 2 3 4 5 Select the Schedule Function checkbox to turn the wireless signal off for the configured period. Click the plus sign (+) to add a scheduling rule. A separate panel displays for configuring wireless schedule rules. Enter a start time and end time for the period in which you want the wireless signal off. Choose Everyday or Individual Days from the drop-down menu. 102 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT 6 7 8 9 If you chose Individual Days, select the checkboxes for the desired days. The Recurrence Pattern shows the rules created to date. If desired, click the plus sign (+) to add more rules. Click Save Changes. STOP. This procedure is complete. Procedure 22 Routing configuration 1 Select Network > Routing from the top-level menu in the GPON Home Gateway window, as shown in Figure 38. Figure 38 Routing network window Table 30 describes the fields in the Routing network window. Issue: 01 3FE-47555-AAAA-TCZZA 103 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Table 30 Routing network parameters Field Enable Routing Description Select this checkbox to enable routing Destination IP Address Enter the destination IP address Destination Netmask Enter the destination network mask Gateway IPv4 Interface Enter the gateway address Choose a WAN connection previously created in the WAN network window from the drop-down menu Forwarding Policy Choose a forwarding policy from the drop-down menu 2 3 4 Enter the routing information. Click Add. STOP. This procedure is complete. 104 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Procedure 23 DNS configuration 1 Select Network > DNS from the top-level menu in the GPON Home Gateway window, as shown in Figure 39. Figure 39 DNS network window Table 31 describes the fields in the DNS network window. Table 31 DNS network parameters Field DNS Proxy Domain Name IPv4 Address Origin Domain New Domain Description Select the Enabled checkbox to enable the DNS proxy Domain name Domain IP address Origin domain name New domain name 2 3 Select the Enabled checkbox and click Save to enable the DNS proxy. Enter the domain name and IPv4 address and click Add. Issue: 01 3FE-47555-AAAA-TCZZA 105 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide 4 5 If required, associate an origin domain with a new domain, click Add. STOP. This procedure is complete. Procedure 24 TR-069 configuration 1 Select Network > TR-069 from the top-level menu in the GPON Home Gateway window, as shown in Figure 40. Figure 40 TR-069 network window Table 32 describes the fields in the TR-069 network window. Table 32 TR-069 network parameters Field Periodic Inform Enable Description Select this checkbox to enable periodic inform updates Periodic Inform Interval(s) Time between periodic inform updates, in seconds URL Username Password URL of the auto-configuration server Username used to log in to the auto-configuration server Password used to log in to the auto-configuration server Connect Request Username Username used to log in to the ONT Connect Request Password Password used to log in to the ONT 2 Configure TR-069 by entering the required information. 106 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT 3 4 Click Save. STOP. This procedure is complete. Procedure 25 GRE Tunnel configuration 1 Select Network > GRE Tunnel from the top-level menu in the GPON Home Gateway window, as shown in Figure 41. Figure 41 GRE Tunnel window Table 33 describes the fields in the GRE Tunnel window. Table 33 GRE Tunnel parameters Field Tunnel Name

(1 of 2) Description Choose Create new GRE Tunnel, or Choose an existing tunnel from the drop-down menu. The tunnel name is automatically assigned by the system. Up to 3 GRE tunnels are supported. Issue: 01 3FE-47555-AAAA-TCZZA 107 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Field WAN Interface Primary Remote End Secondary Remote End (optional) Description Choose a WAN interface from the drop-down menu. GRE tunnels can only be created on HSI-enabled WAN interfaces. Enter an IP address or FQDN that is unique in the system. If the primary remote endpoint is down or unreachable, the secondary remote endpoint becomes active, if configured. The secondary remote endpoint remains active until it becomes unreachable, in which case the primary remote endpoint becomes active again. Revertive mode is not supported. If both endpoints are unreachable, the GRE tunnel is declared down. Connected Remote End This field displays the current data traffic path for the GRE tunnel. Failover mechanism This feature is automatically selected by the system. Traffic timeout to start pings Enter the traffic timeout in seconds (0 to 100). No. of retries before unreachable Enter the number of retries before the tunnel is declared down (2 to 1024).

(2 of 2) 2 3 4 Configure the GRE tunnel by entering or selecting the required information. Click Save. STOP. This procedure is complete. Procedure 26 QoS configuration 1 Select Network > QoS Config from the top-level menu in the Home Gateway window. Figure 42 shows the window for configuring QoS L2 (Layer 2 packet sizes). 108 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Figure 42 QoS Config window (L2) Figure 43 shows the window for configuring QoS L3 (Layer 3 packet sizes). Issue: 01 3FE-47555-AAAA-TCZZA 109 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Figure 43 QoS Config window (L3) Table 34 describes the fields in the QoS Config window. Table 34 QoS Config parameters Field Type Source MAC Interface DSCP Mark 802.1p Mark

(1 of 2) Description Choose a QoS service layer type from the drop-down menu L2 or L3. Enter the source MAC Select the Exclude checkbox to exclude the source MAC Choose an interface from the drop-down menu Enter the value for the DSCP mark (range: 0-63); valid only for L3 Criteria Enter the value for the 802.1p (range: 0-7) 110 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Field Forwarding Policy Additional fields for L3 Protocol Application Source IP and Source IP Mask Destination IP and Destination IP Mask Description Enter the number for the forwarding policy (range: 1-7) Choose a protocol from the drop-down menu, or select the Exclude checkbox Choose an application from the drop-down menu Enter the values for the source IP and IP mask, or select the Exclude checkbox Enter the values for the destination IP and IP mask, or select the Exclude checkbox Source Port and Source Port Max Enter the values for the source port and port max (highest port number) or select the Exclude checkbox Destination Port and Destination Port Max Enter the values for the destination port and port max (highest port number), or select the Exclude checkbox

(2 of 2) 2 3 4 5 Choose a QoS type from the drop-down menu: L2 or L3. Configure a QoS policy. Click Add to add a QoS policy. STOP. This procedure is complete. Procedure 27 Upstream (US) Classifier configuration The US Classifier feature is used to create policies, classifiers, and classifier rules for upstream traffic handling. This feature is available to admin users (super users) only. A policy defines an action to be performed on a set of LAN or WAN packets. A policy can be created at any time and then subsequently assigned to one or more classifiers. A classifier is used to select key fields for which the classifier rules will be written. A classifier can be created at any time and then subsequently assigned to one or more classifier rules. A classifier rule is used to assign actions to a group of packets based on a set of parameters. A classification rule must be created against a pre-defined classifier. Up to 16 policies can be created, with up to 8 classifiers and 32 classifier rules. 1 Select Network > US Classifier from the top-level menu in the GPON Home Gateway window, and select the Policy tab, as shown in Figure 44. All classifier policies are displayed in the policy table in the window. Issue: 01 3FE-47555-AAAA-TCZZA 111 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Figure 44 US Classifier Policy window Table 35 describes the fields in the US Classifier Policy window. Table 35 US Classifier Policy parameters Field Tunnel Type Tunnel Interface VLAN ID VLAN Tag VLAN Priority IP TOS/DSCP Drop Description The tunnel type is set to GRE and cannot be modified. Choose a tunnel interface from the drop-down menu: No Tunnel, GRE Tunnel, or LAN traffic. Enter a VLAN ID (0-4094). This field is not configurable. The VLAN tag is set to 8100 (hexadecimal). Enter a VLAN priority level (0 to 7). A lower number indicates a higher priority. This field is not configurable. All tunnel packets are generated with a default DSCP value (usually 0). Select this checkbox to drop the packets 2 3 Select a tunnel interface. Enter a VLAN ID and priority level. 112 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT 4 5 6 Click Save. To delete a policy, click the Delete option for the applicable policy in the policy table. A policy can only be deleted if it is not associated with any classifier rules. Select Network > US Classifier from the top-level menu in the GPON Home Gateway window, and select the Classifier tab, as shown in Figure 45. All classifiers are displayed in the classifier table in the window. Figure 45 US Classifier window Table 36 describes the fields in the US Classifier window. Table 36 US Classifier parameters Field Interface Source MAC Destination MAC Source IP

(1 of 2) Description Choose an interface from the drop-down menu; for example, None, LAN, 2.4G SSID, or 5G SSID. Click to enter a source MAC Click to enter a destination MAC Click to enter a source IP Issue: 01 3FE-47555-AAAA-TCZZA 113 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Field Destination IP Source Port Destination Port Protocol Priority

(2 of 2) Description Click to enter a destination IP Click to enter a source port Click to enter a destination port Click to enter a protocol Choose a priority level from 1 to 8. The lower the number, the higher the priority. No more than 1 classifier can be created with the same priority. 7 8 9 Configure the US classifier. At least one field must be selected to create a classifier. A maximum of four fields may be selected to create a classifier; this includes the interface field. Click Save. To delete a classifier, click the Delete option for the applicable classifier in the classifier table. A classifier can only be deleted if it is not associated with any classifier rules. 10 Select the Classifier Rules tab, as shown in Figure 46. All classifier rules are displayed in the classifier rules table in the window. Figure 46 US Classifier Rules window 114 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Table 37 describes the fields in the US Classifier Rules window. Table 37 US Classifier Rules parameters Field Policy Classifier Interface Source MAC Destination MAC Source IP Destination IP Source Port Destination Port IP Protocol Type Description Choose a policy from the drop-down menu Choose a classifier from the drop-down menu Choose an interface from the drop-down menu; for example, None, LAN, 2.4G SSID, 5G SSID. Enter a source MAC Enter a destination MAC Enter a source IP Enter a destination IP Enter a source port Enter a destination port Enter a value between 0 and 254 11 Configure the classifier rule. 12 Click Save. 13 To delete a classifier rule, click the Delete option for the applicable classifier rule in the classifier rules table. 14 STOP. This procedure is complete. 7.2.4 Security configuration firewall IP filter G-240W-G ONTs also supports security configuration, including:

MAC filter URL filter parental control DMZ and ALG access control Issue: 01 3FE-47555-AAAA-TCZZA 115 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Procedure 28 Firewall configuration 1 Select Security > Firewall from the top-level menu in the GPON Home Gateway window, as shown in Figure 47. Figure 47 Firewall window Firewall security applies only to services provided by the ONT. Internet access from the LAN side is not affected by this firewall. Four security options are available: High, Low, Off, and Advanced. HighTraffic denied inbound and minimally permit common services outbound LowAll outbound traffic and pinhole-defined inbound traffic is allowed OffAll inbound and outbound traffic is allowed AdvancedAdvanced firewall configuration applies as specified Table 38 describes the fields in the firewall window. Table 38 Firewall parameters Field Security Level

(1 of 2) Description Choose the security level from the drop-down menu: High, Low, Off, or Advanced 116 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Field Level Advance Attack Protection

(Protection against DoS or DDoS attacks)

(2 of 2) Description Choose Advanced to configure the DMZ and IP filter Choose Enable or Disable attack protection from the drop-down menu. The default is Enable. 2 3 4 Configure the firewall. Click Save. STOP. This procedure is complete. Procedure 29 MAC filter configuration 1 Select Security > Mac Filter from the top-level menu in the GPON Home Gateway window, as shown in Figure 48. Figure 48 MAC filter window Table 39 describes the fields in the MAC filter window. Issue: 01 3FE-47555-AAAA-TCZZA 117 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Table 39 MAC filter parameters Field Ethernet Interface MAC Filter Mode Description Choose the MAC filter mode from the drop-down menu: Blocked or Allowed LAN Port LAN port range MAC Address Wi-Fi SSID MAC Filter Mode Choose a MAC address from the drop-down menu or enter the address in the text field Choose the MAC filter mode from the drop-down menu: Blocked or Allowed SSID Select Choose the SSID from the drop-down menu Enable Select this checkbox to enable the MAC filter MAC Address Choose a MAC address from the drop-down menu or enter the address in the text field 2 3 4 5 Click Refresh to update the information. Configure a MAC filter. Click Add. STOP. This procedure is complete. 118 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Procedure 30 IP filter configuration 1 Select Security > IP filter from the top-level menu in the GPON Home Gateway window, as shown in Figure 49. Figure 49 IP filter window Table 40 describes the fields in the IP filter window. If the firewall level is not set to advanced, the IP filter rules are not available. IP filter parameters Table 40 Field Mode Internal Client Local IP Address Description Choose an IP filter mode from the drop-down menu:

Drop for upstream Drop for downstream Choose an internal client from the drop-down menu:

Customer setting - uses the IP address input below Local IP address IP - uses the connecting devices' IP to the ONT Source Subnet Mask Source subnet mask Remote IP Address Remote IP address Destination Subnet Mask Destination subnet mask Protocol Choose an application protocol or all from the drop-down menu Issue: 01 3FE-47555-AAAA-TCZZA 119 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide 2 3 4 Configure the IP filter. Click Add. STOP. This procedure is complete. Procedure 31 URL filter configuration 1 Select Security > URL Filter from the top-level menu in the GPON Home Gateway window, as shown in Figure 50. Figure 50 URL Filter window Note You cannot use URL filtering for HTTPS. The URL is encrypted when using HTTPS. Table 41 describes the fields in the URL Filter window. 120 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Table 41 URL Filter parameters Field Enable URL filter Description Select the checkbox to enable the URL filter URL filter type URL List URL Address Select the radio button to block the URL or allow the URL Type the URL address Port - default to 80 Type the port number; the default is 80 2 3 4 Configure the URL Filter. Click Add Filter. STOP. This procedure is complete. Issue: 01 3FE-47555-AAAA-TCZZA 121 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Procedure 32 Parental control 1 Select Security > Parent Control from the top-level menu in the GPON Gateway window, as shown in Figure 51. 122 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Figure 51 Parental Control window Table 42 describes the fields in the Parental Control window. Issue: 01 3FE-47555-AAAA-TCZZA 123 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Table 42 Parental control parameters Description Select this checkbox to enable access control Field Access Control Add Access Control rule Policy Name Enter a name for the parental control policy or choose a policy from the list MAC Address IPv4 Address Url Port Days of week From To Enter the MAC address or choose a MAC address from the list Enter the IPv4 address for the device or choose an IPv4 address from the list Enter the URL port for the device Choose Every Day, or Individual Days and select the checkboxes for the days of the week for which the policy applies Enter the times for the policy to be in effect Select the Access Control checkbox. Click on the plus sign (+) to add a policy. A separate panel displays for configuring the policy name, IP address of the device, and dates and times for the policy. Configure the parental control policy. Click Enable to activate the policy. STOP. This procedure is complete. 2 3 4 5 6 124 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Procedure 33 DMZ and ALG configuration 1 Select Security > DMZ and ALG from the top-level menu in the GPON Home Gateway window, as shown in Figure 52. Figure 52 DMZ and ALG window Table 43 describes the fields in the DMZ and ALG window. Table 43 DMZ and ALG parameters Description Select the checkboxes to enable the protocols to be supported by the ALG: FTP, TFTP, SIP, H323, RTSP, L2TP, IPSEC, PPTP Choose a WAN connection from the drop-down menu Select this checkbox to enable DMZ on the chosen WAN connection Choose Customer Setting and enter the DMZ IP address or choose the IP address of a connected device from the drop-down menu Field ALG Config DMZ Config WAN Connection List Enable DMZ DMZ IP Address 2 3 4 Configure ALG. Click Save ALG. Configure DMZ. Issue: 01 3FE-47555-AAAA-TCZZA 125 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide 5 6 Click Save DMZ. STOP. This procedure is complete. Procedure 34 Access control configuration This procedure describes how to configure the access control level (ACL). Note 1 ACL takes precedence over the firewall policy. Note 2 The trusted network object will be shared for all WAN connections; it is not applied individually to a WAN connection. 1 Select Security > Access Control from the top-level menu in the GPON Home Gateway window, as shown in Figure 53. Figure 53 Access Control window Table 44 describes the fields in the Access Control window. Table 44 Access control parameters Field WAN

(1 of 2) Description Choose a connection from the drop-down menu 126 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Field Trusted Network Enable ICMP, SSH, HTTP, TR-069 Description Click the checkbox to enable or disable Select an access control level for each protocol:

WAN side: Allow, Deny, or Trusted Network Only LAN side: Allow or Deny Trusted Network Source IP Start Source IP End

(2 of 2) Enter a start IP address for the new subnet trusted network Enter an end IP address for the new subnet trusted network 2 3 4 5 6 Select a WAN connection from the drop-down menu. Click to enable or disable Trusted Network. Select an access control level for each of the four protocols: ICMP, SSH, HTTP, and TR-069 for both the WAN and the LAN side. Click Save. Optionally, add one or more subnet trusted networks. The maximum number of entries is 32. You can also use the Source IP fields to delete a previously created entry for a subnet trusted network. 7 STOP. This procedure is complete. 7.2.5 Application configuration G-240W-G ONTs also supports application configuration, including:

port forwarding port triggering DDNS NTP USB UPnP and DLNA voice setting Issue: 01 3FE-47555-AAAA-TCZZA 127 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Procedure 35 Port forwarding configuration 1 Select Application > Port forwarding from the top-level menu in the GPON Home Gateway window, as shown in Figure 54. Figure 54 Port forwarding window Table 45 describes the fields in the port forwarding window. Table 45 Port forwarding parameters Field Application Name WAN Port LAN Port Internal Client Protocol Enable Mapping WAN Connection List Description Choose an application name from the drop-down menu WAN port range LAN port range Choose a connected device from the drop-down menu and enter the associated IP address Choose the port forwarding protocol from the drop-down menu:

TCP UDP Select this checkbox to enable mapping TCP/UDP Choose a WAN connection from the drop-down menu Note: only active devices are shown on this menu 2 Configure port forwarding. 128 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT 3 4 Click Add. STOP. This procedure is complete. Procedure 36 Port triggering 1 Select Application > Port Triggering from the top-level menu in the GPON Gateway window, as shown in Figure 55. Figure 55 Port Triggering window Table 46 describes the fields in the Port Triggering window. Table 46 Port triggering parameters Field Application Name Open Port Triggering Port Expire Time

(1 of 2) Description Choose an application name from the drop-down menu Enter the open port range Enter the triggering port range Enter the expiration time in seconds Issue: 01 3FE-47555-AAAA-TCZZA 129 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Field Open Protocol Trigger Protocol Enable Triggering WAN Connection List

(2 of 2) TCP/UDP Description Choose the open port protocol from the drop-down menu:

TCP UDP Choose the triggering port protocol from the drop-down menu:

TCP UDP Select this checkbox to enable port triggering TCP/UDP Choose a WAN connection from the drop-down menu Note: only active devices are shown on this menu 2 3 4 Configure port triggering. Click Add. STOP. This procedure is complete. 130 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Procedure 37 DDNS configuration 1 Select Application > DDNS from the top-level menu in the GPON Home Gateway window, as shown in Figure 56. Figure 56 DDNS window Table 47 describes the fields in the DDNS window. Table 47 DDNS parameters Field WAN Connection List Description Choose a WAN connection from the drop-down menu Enable DDNS Select this checkbox to enable DDNS on the chosen WAN connection ISP Choose an ISP from the drop-down menu. Domain Name Domain name Username Password Displays the status of the DDNS: Synchronized, Synchronization failed, or blank if no update message has been received from the ISP. Username Password DDNS Status 2 Configure DDNS. Issue: 01 3FE-47555-AAAA-TCZZA 131 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide 3 4 Click Save. STOP. This procedure is complete. Procedure 38 NTP configuration 1 Select Application > NTP from the top-level menu in the GPON Home Gateway window, as shown in Figure 57. Figure 57 NTP window Table 48 describes the fields in the NTP window. Table 48 NTP parameters Field Enable NTP Service Description Select this checkbox to enable NTP service Current Time Enter the current local date and time Primary Time Server Choose a time server from the drop-down menu or choose Customer setting and enter the address of the time server. Secondary Time Server Choose a time server from the drop-down menu or choose Customer setting and enter the address of the time server.

(1 of 2) 132 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Field Third Time Server Description Choose a time server from the drop-down menu or choose Customer setting and enter the address of the time server. Interval Time Time Zone

(2 of 2) Interval at which to get the time from the time server, in seconds Choose the local time zone from the drop-down menu 2 3 4 Configure NTP. Click Save. STOP. This procedure is complete. Procedure 39 USB configuration You can connect USB storage devices and USB printers to the USB ports of the device. The USB menu enables you to configure FTP, SFTP, and Samba servers for your USB storage devices. Note Due to image size limitations, some OLTs may not be able to support the Samba server feature. For this reason, two types of ONT software images are available: the Premium Image supports the FTP, SFTP, and Samba features; the Advanced Image supports the FTP and SFTP features but does not support the Samba server feature. For more information, contact your Nokia representative. You can also use the USB menu to enable and disable USB printer sharing across clients on the LAN. The USB connected devices are shown in overview table on the bottom of the USB window. The device incorporates a CUPS server to enable USB printer sharing across the LAN by using the RAW print-through protocol. When a USB printer is connected to the device, it can be configured on LAN clients by referring to http://<hostname>:631/printers/<printer_name>

Issue: 01 3FE-47555-AAAA-TCZZA 133 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide as a shared printer, where <hostname> refers to the DNS name or the IP address of the device and the <printer_name> is displayed in the connected USB device table of the USB page. The USB printer driver must be installed on the LAN client to execute print jobs. When an error prevents the print job from being completed, a generic error message is returned to the LAN client. Up to four print jobs at a time are supported. 1 Select Application > USB from the top-level menu, as shown in Figure 58. Figure 58 USB window Table 49 describes the fields in the USB window. Table 49 USB parameters Description Select this checkbox to enable using an FTP server Username for the FTP server Password for the FTP server Password for the FTP server Field Enable FTP server Username Password Re-enter Password 2 Configure USB. 134 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT 3 4 Click Save. STOP. This procedure is complete. Procedure 40 UPnP and DLNA configuration 1 Select Application > UPnP and DLNA from the top-level menu in the GPON Home Gateway window, as shown in Figure 59. Figure 59 UPnP and DLNA window 2 3 4 Select the Enable UPnP/DLNA checkbox to enable UPnP/DLNA. Click Save/Apply. STOP. This procedure is complete. Issue: 01 3FE-47555-AAAA-TCZZA 135 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Procedure 41 Voice setting 1 Select Application > Voice Setting from the top-level menu in the GPON Home Gateway window, as shown in Figure 60. Figure 60 Voice setting window Table 50 describes the fields in the Voice Setting window. Table 50 Voice setting parameters Field Voice Setting Outbound Proxy Description Enter the SIP outbound proxy Outbound Proxy Port Enter the outbound proxy port Proxy Server Enter the proxy server Proxy Server Port Enter the proxy server port

(1 of 2) 136 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Field Registrar Server Description Enter the registrar server Registrar Server Port Enter the registrar server port UserAgentDomain Enter the user agent domain UserAgentPort Enter the user agent port DigitMap DTMF Mode FaxT38 Line Setting POTS line Enable A string of characters with a length limit of 1024 bytes. A dial plan can consist of several dial plan tokens. Each token is a component of the overall dial plan. Choose InBand, RFC2833, Info, or Auto from the drop-down menu Choose False or True from the drop-down menu Choose a POTS line from the drop-down menu Choose Enabled or Disabled from the drop-down menu Directory Number Enter a directory number AuthUserName AuthPassword Enter an authorized user name Enter a password for the user URI

(2 of 2) The Uniform Resource Identifier of the SIP URL 2 3 4 Configure voice setting. Click Save. STOP. This procedure is complete. 7.2.6 Maintenance G-240W-G ONTs also supports maintenance tasks, including:

change password test WAN speed configure LOID configure SLID manage device backup and restore upgrade firmware diagnose WAN connections reboot device restore factory defaults Issue: 01 3FE-47555-AAAA-TCZZA 137 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide view log diagnose PPPoE connection Procedure 42 Password configuration A password must adhere to the password rules, which are as follows:

the password may consist of uppercase letters, lowercase letters, digital numbers, and the following special characters ! # + , - / @ _ : = ]

the password length must be from 8 to 24 characters the first character must be a digital number or a letter the password must contain at least two types of characters: numbers, letters, or special characters the same character must not appear more than 8 times in a row When the password meets the password rules, the application displays the message Your password has been changed successfully. When the password does not meet the password rules, the application displays a message to indicate which password rule has not been followed, for example:

the password is too short the password is too long 138 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT the first character cannot be a special character there are not enough character classes 1 Select Maintenance > Password from the top-level menu in the GPON Home Gateway window, as shown in Figure 61. Figure 61 Password window Table 51 describes the fields in the password window. Table 51 Password parameters Field Original Password Description Current password New Password New password (must adhere to the password rules described above) Re-enter password Must match the new password entered above exactly Prompt message Password prompt message 2 Configure the new password. Issue: 01 3FE-47555-AAAA-TCZZA 139 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide 3 4 Click Save. STOP. This procedure is complete. Procedure 43 WAN speed test 1 Select Maintenance > Speed Test from the top-level menu in the GPON Home Gateway window, as shown in Figure 62. Figure 62 Speed Test window 2 3 Click Start to start the speed test. Enter the URL for the test server in the pop-up window. STOP. This procedure is complete. 140 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Procedure 44 LOID configuration 1 Select Maintenance > LOID Config from the top-level menu in the GPON Home Gateway window, as shown in Figure 63. Figure 63 LOID Config window Table 52 describes the fields in the LOID configuration window. Table 52 LOID configuration parameters Field LOID Description Type the LOID; the maximum number of characters is 24 If the password is null, this field may be left blank Password Type the password; the maximum number of characters is 12 2 3 4 Configure the LOID. Click Save/Apply. STOP. This procedure is complete. Issue: 01 3FE-47555-AAAA-TCZZA 141 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Procedure 45 SLID configuration 1 Select Maintenance > SLID Configuration from the top-level menu in the GPON Home Gateway window, as shown in Figure 64. Figure 64 SLID configuration window Table 53 describes the fields in the SLID configuration window. Table 53 SLID configuration parameters Field Current SLID Description Displays current SLID Enter new SLID Input new SLID SLID Mode Choose a SLID mode from the drop-down menu 2 Configure the new SLID. 142 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT 3 4 Click Save. STOP. This procedure is complete. Procedure 46 Device management 1 Select Maintenance > Device Management from the top-level menu in the GPON Home Gateway window, as shown in Figure 65. Figure 65 Device management window Table 54 describes the fields in the Device management window. Table 54 Device management parameters Field Host Name Host Alias Description Choose a host from the drop-down menu Enter an alias for the chosen host Issue: 01 3FE-47555-AAAA-TCZZA 143 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide 2 3 4 Configure an alias for a specific host. Click Add. STOP. This procedure is complete. Procedure 47 Backup and restore 1 Select Maintenance > Backup and Restore from the top-level menu in the GPON Home Gateway window, as shown in Figure 66. Figure 66 Backup and Restore window 2 Click Choose file and select a backup file. 144 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT 3 4 Click Import Config File to restore the ONT to the saved backup or click Export Config File to export the current ONT configuration to the backup file. STOP. This procedure is complete. Procedure 48 Upgrade firmware 1 Select Maintenance > Firmware Upgrade from the top-level menu in the GPON Home Gateway window, as shown in Figure 67. Figure 67 Firmware upgrade window 2 3 4 Click Choose file and select the firmware file. Click Upgrade to upgrade the firmware. STOP. This procedure is complete. Issue: 01 3FE-47555-AAAA-TCZZA 145 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Procedure 49 Reboot ONT 1 Select Maintenance > Reboot Device from the top-level menu in the GPON Home Gateway window, as shown in Figure 68. Reboot window Figure 68 2 3 Click Reboot to reboot the ONT. STOP. This procedure is complete. 146 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Procedure 50 Restore factory defaults 1 Select Maintenance > Factory Default from the top-level menu in the GPON Home Gateway window, as shown in Figure 69. Figure 69 Factory default window 2 3 Click Factory Default to reset the ONT to its factory default settings. STOP. This procedure is complete. Issue: 01 3FE-47555-AAAA-TCZZA 147 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Procedure 51 Diagnose WAN connections 1 Select Maintenance > Diagnose from the top-level menu in the GPON Home Gateway window, as shown in Figure 70. Figure 70 Diagnose window 2 3 4 5 6 7 8 Choose a WAN connection to diagnose from the drop-down menu. Enter the IP address or domain name. Select the test type: ping, traceroute, or both. Enter the number of ping attempts to perform (1 - 1000); the default is 4. Enter a ping packet length (64-1024); the default is 64. Enter the maximum number of trace hops (1-255); the default is 30. Click Start Test. Results will be displayed at the bottom of the window. 148 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT 9 Click Cancel to cancel the test. 10 STOP. This procedure is complete. Procedure 52 View log files 1 Select Maintenance > Log from the top-level menu in the GPON Home Gateway window, as shown in Figure 71. Figure 71 Log window Issue: 01 3FE-47555-AAAA-TCZZA 149 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide 2 3 4 5 Choose a write level from the drop-down menu to determine which types of events are recorded in the log file:

Emergency Alert Critical Error Warning Notice Debug Informational Choose a reading level from the drop-down menu to determine which types of events to display from the log file:

Emergency Alert Critical Error Warning Notice Debug Informational The log file is displayed at the bottom of the window. STOP. This procedure is complete. 150 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Procedure 53 Diagnose PPPoE connections 1 Select Maintenance > PPPoE Diagnostics from the top-level menu in the GPON Home Gateway window, as shown in Figure 72. Figure 72 PPPoE Diagnostics window 2 Click Check to view the results for the PPPoE diagnostics, as shown in Figure 73. Issue: 01 3FE-47555-AAAA-TCZZA 151 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Figure 73 PPPoE diagnostics results Table 55 describes the fields on the PPPoE diagnostics results window. Table 55 PPPoE diagnostics results parameters Field PON PPPoE Internet Description Reports whether the PON link is up or down Reports whether the PPPoE IPv4 or IPv6 connection is up, connecting, down, not configured, or not found For each Internet connection, reports whether the connection succeeded, failed (missing DNS address), or was not found; also reports failures due to packet loss higher than the threshold of 30 3 STOP. This procedure is complete. 7.2.7 RG troubleshooting counters The Troubleshooting Counters feature enables service providers and end users to monitor the performance of their broadband connection. 152 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Tests are run to retrieve upstream and downstream throughput, latency, and DNS response time. The Troubleshooting Counters window also displays upstream and downstream packet loss and Internet status. Procedure 54 Retrieve Residential Gateway (RG) troubleshooting counters 1 Select RG Troubleshooting Counters from the left menu in the GPON Home Gateway window. The RG Troubleshooting Counters window appears; see Figure 74. Figure 74 RG Troubleshooting Counters window Table 56 describes the fields in the RG Troubleshooting Counters window. Table 56 RG Troubleshooting Counters parameters Field WAN Connection List US Throughput DS Throughput US Packet Loss DS Packet Loss Internet Status

(1 of 2) Description Choose a WAN connection from the list This test is used to determine the upstream throughput/speed Click US Speed Test to specify the time for the upstream test The default is weekly, performed at idle to a public server This test is used to determine the downstream throughput/speed Click DS Speed Test to specify the time for the downstream test The default is weekly, performed at idle to a public server The number of upstream packages lost The number of downstream packages lost Whether the broadband connections is active (UP) or not (DOWN) Issue: 01 3FE-47555-AAAA-TCZZA 153 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Field Latency DNS Response Time Description This test is used to determine the lowest round-trip time in milliseconds by pinging the target server multiple times Click Latency Test to specify the time for the test The default is weekly, performed at idle to a public server This test is used to determine the lowest round-trip time in milliseconds by sending a request to the target DNS server Click DNS Response Test to specify the time for the test The default is weekly, performed at idle to a public server

(2 of 2) 2 3 4 Configure the test times if desired. Click Refresh to update the data. STOP. This procedure is complete. 7.3 SFU mode configuration HGU is the default mode for the G-240W-G ONT, but you can use SFU mode to view device status information, change the password, authenticate the LOID, and change the SLID. 7.3.1 Switch from default HGU mode to SFU mode To switch from the default HGU mode to using SFU mode, use the procedure below. Procedure 55 Switching to SFU mode 1 2 3 4 Power up the G-240W-G ONT. Change the Operator ID (OPID) to XXXX to enable the ONT to switch to SFU mode, as described in Modifying the operator ID. Reboot the ONT. STOP. This procedure is complete. 154 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Procedure 56 Modifying the operator ID 1 2 3 4 5 6 7 8 Register the ONT with the OLT. Check the original OPID. Use the T&D command on the ONT console (ri tool dump) to check the current OPID. Using an XML editor, create a file called OntConfig.xml with the following content:

<OperatorObject version=1.0>

<OperatorID=abcd>

</OperatorObject>

where: abcd is the correct operator ID, for example ALCL for HGU mode with TR-069 or TR-104 voice management, ALCO for HGU mode with OMCI V1 or V2 voice management, or XXXX for generic SFU mode. Use a TFTP client tool to transfer the OntConfig.xml file to the OLTs ONT directory and change the filename to the software version number, for example, 3FE123456789.xml. See the OLT documentation for the location of the ONT directory. Use a TL1 command to configure ONUSWCRTL:

ENT-ONTSWCTRL::1::::HWVER=hwver,VARNT=,PLNDSWVER=UNPLANNED, PLNDSWVERCONF=UNPLANNED,DLDSWVER=swver;

where:

hwver is the EQPTVERNUM, for example EQPTVERNUM=3FE12345AAAA. swver is the software version number used as the filename in step 2, for example 3FE123456789.xml. See the TL1 Commands and Messages Guide for the 7342 or 7360 for more information about the ENT-ONTSWCTRL command. Download the xml file to update the operator ID:

ED-ONT::ONT-1/1/3/1/19::::DLSW=AUTO;

Restart the ONT, then connect to the LAN and use the T&D command on the ONT console

(ri tool dump) to check the OPID. Use a TL1 command to disable further downloads:

ED-ONT::ONT-1/1/3/1/19::::DLSW=DISABLED;

Issue: 01 3FE-47555-AAAA-TCZZA 155 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide To enable auto download again, use the DEL-ONTSWCTRL command. See the TL1 Commands and Messages Guide for the 7342 or 7360 for more information about the DEL-ONTSWCTRL command. 9 STOP. This procedure is complete. 7.3.2 Login Use the procedure below to login to the web-based GUI for the G-240W-G ONT. Procedure 57 Login to web-based GUI 1 Open a web browser and enter the IP address of the ONT in the address bar. The login window appears. The default gateway IP address is http://192.168.1.254. You can connect to this IP address using your web browser after connecting your PC to one of Ethernet ports of the ONT. The static IP address of your PC must be in the same subnet as the ONT. 2 Enter your username and password in the Log in window, as shown in Figure 75. The default username is adminadmin. The default password is ALC#FGU. Figure 75 Web login window Caution Pressing the Reset button for less than 10 seconds reboots the ONT; pressing the Reset button for 10 seconds resets the ONT to the factory defaults, except for the LOID and SLID. 156 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Note If you forget the current username and password, press the reset button for 5 s and the default values for the username and password will be recovered at startup. 3 4 Click Login. STOP. This procedure is complete. 7.3.3 Device and connection status G-240W-G ONTs support the retrieval of a variety of device information. Procedure 58 Device information retrieval 1 Select Status > Device Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 76. Figure 76 Device Information window Table 57 describes the fields in the Device Information window. Issue: 01 3FE-47555-AAAA-TCZZA 157 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide Table 57 Device Information parameters Field Device Name Vendor Serial Number Description Name on the ONT Name of the vendor Serial number of the ONT Hardware version Hardware version of the ONT Boot version Boot version of the ONT Software version Software version of the ONT Chipset Chipset of the ONT Device Running Time Amount of time the device has run since last reset in hours, minutes, and seconds 2 3 Click Refresh to update the displayed information. STOP. This procedure is complete. 7.3.4 Maintenance G-240W-G ONTs also support maintenance tasks, including:

password change LOID configuration SLID configuration Procedure 59 Password configuration A password must adhere to the password rules, which are as follows:

the password may consist of uppercase letters, lowercase letters, digital numbers, and the following special characters ! # + , - / @ _ : = ]

the password length must be from 8 to 24 characters the first character must be a digital number or a letter the password must contain at least two types of characters: numbers, letters, or special characters the same character must not appear more than 8 times in a row When the password meets the password rules, the application displays the message Your password has been changed successfully. 158 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT When the password does not meet the password rules, the application displays a message to indicate which password rule has not been followed, for example:

the password is too short the password is too long the first character cannot be a special character there are not enough character classes 1 Select Maintenance > Password from the top-level menu in the GPON Home Gateway window, as shown in Figure 77. Figure 77 Password window Table 58 describes the fields in the password window. Table 58 Password parameters Field New Password Description New password (must adhere to the password rules described above) Re-enter Password Must match the new password entered above exactly Prompt Message Password prompt message 2 Configure the new password. Issue: 01 3FE-47555-AAAA-TCZZA 159 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide 3 4 Click Save. STOP. This procedure is complete. Procedure 60 LOID configuration 1 Select Maintenance > LOID Config from the top-level menu in the GPON Home Gateway window, as shown in Figure 78. Figure 78 LOID configuration window 2 3 4 5 Enter the LOID. Enter the password, if applicable. Click Save/Apply. STOP. This procedure is complete. 160 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide Configure a G-240W-G indoor ONT Procedure 61 SLID configuration 1 Select Maintenance > SLID Configuration from the top-level menu in the GPON Home Gateway window, as shown in Figure 79. Figure 79 SLID configuration window Table 59 describes the fields in the SLID configuration window. Table 59 SLID configuration parameters Field Current SLID Description Displays current SLID Input New SLID Enter new SLID SLID Mode Choose a SLID mode from the drop-down menu 2 3 4 Configure the new SLID. Click Save. STOP. This procedure is complete. Issue: 01 3FE-47555-AAAA-TCZZA 161 Configure a G-240W-G indoor ONT 7368 ISAM ONT G-240W-G Product Guide 162 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide ONT configuration file over OMCI 8 ONT configuration file over OMCI 8.1 Purpose 8.2 Supported configuration file types 8.3 ONT configuration file over OMCI 8.1 Purpose This procedure describes how to use configuration files over OMCI to configure ONTs. Some advantages include:

ability to securely download any configuration file to an ONT ability to avoid using embedded configuration files in ONT software flexibility to change the ONT default behavior by downloading configuration file flexibility to update a deployed ONT by downloading updated parameters Note This feature is supported for use with the 7360 ISAM FX and the 7342 ISAM FTTU. 8.2 Supported configuration file types Table 60 describes the configuration file types that are supported from 7368 ISAM ONT R05.02.00 and later. Issue: 01 3FE-47555-AAAA-TCZZA 163 ONT configuration file over OMCI 7368 ISAM ONT G-240W-G Product Guide Supported ONTs/DPU HGU ONTs:

G-240G-C,G-240W-A, G-240W-B, G-240W-C, G-240W-G, I-240W-A Table 60 Supported configuration files File Index PRE Description ONT pre-configuration file CFG ONT configuration delta file XML Voice XML file

(1 of 2) Details The XML-based PRECONFIG file controls the working mechanics of the ONT for various services. The default behavior of different ONTs may vary based on the factory settings. The pre-configuration file includes the factory default value for the residential gateway. Note: the pre-configuration file does not work with SFU ONTs; therefore, this feature applies only to Residential Gateway ONTs. The pre-configuration file can be used as is, but Nokia provides its customers with the flexibility to customize the pre-configuration file. This pre-configuration file enables operators to change the default behavior by downloading a customized pre-configuration based on customer inputs. This PRE XML file includes a custom OPERID. The Nokia defined index for the PRECONFIG file is:

"PRE"

The XML-based CFG file updates the configurable parameters (the PRE settings) in the existing PRE file of a deployed ONT, where required. This configuration file enables operators to change the deployed behavior by downloading customized updates in the CFG file. This file is used only to modify the parameters in the PRE file; it is not used for service provisioning. No OPERID is required, because the update is based on the OPERID used for the PRE file. The Nokia defined index for the PRECONFIG DELTA file is: "CFG"

The Voice XML file provides an alternate method for securely downloading voice parameters from the OLT, rather than using FTP (OMCIv1/OMCIv2) or HTTPS

(TR-069). Downloading this file makes the applicable changes in the voice parameters. This file enables operators to change the voice behavior by downloading the updated voice XML file. Nokia recommends using this procedure, rather than embedded voice XML files. The Nokia defined index for the Voice XML file is:

"XML"

164 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide ONT configuration file over OMCI File Index GFT Description G.fast-related configuration file

(2 of 2) Supported ONTs/DPU HGU ONTs:

G-240G-C,G-240W-A, G-240W-B, G-240W-C, G-240W-G, I-240W-A Details This text-based json script file controls the default behavior of the G.Fast ONT. This file includes the provisioning parameters of the G.fast transports layer; it does not include VLAN or QoS provisioning. While the ONT functions well with the default values;

they can optionally be customized. While default values can work in VDSL mode, a download file is required for the device to function as a G.fast ONT. The Nokia defined index for the G.fast file is: "GFT"

8.2.1 Filename conventions Nokia provides the raw configuration files, which must be saved by the operator in a TAR file to be uploaded. TAR file names must be unique. The filenames of the raw configuration files may not adhere to the naming conventions outlined below. In this case, the files must be renamed to adhere to the naming conventions before the operator generates the TAR file. Filenames are not case-sensitive. ABCXXXXVER where ABC is the file index type (PRE, CFG, XML, GFT) XXXX is the operator ID For PRE and CFG, a valid operator ID is required For XML and GFT, any characters may be used VER is the file version (from 001 to 999) Note: you cannot update the configuration using two files with the same name. 8.3 ONT configuration file over OMCI Warning Executing the following procedure will trigger the ONT to reboot, which will impact ongoing services. Use this procedure to configure ONTs using configuration files via OMCI. Issue: 01 3FE-47555-AAAA-TCZZA 165 ONT configuration file over OMCI 7368 ISAM ONT G-240W-G Product Guide Procedure 62 Configuring an ONT using a configuration file via OMCI 1 Generate the TAR file to be uploaded to the OLT. Using the raw configuration file(s) provided by Nokia, generate the TAR file as follows:

i ii On a Linux platform, rename the raw configuration file to adhere to the naming convention, as described in section 8.2. Tar the ABCXXXXVER raw configuration file:

tar -cf ABCXXXXVER.tar ABCXXXXVER Where ABCXXXXVER Is the name of the file created in step i. This creates two files: ABCXXXXVER and ABCXXXXVER.tar. iii Rename ABCXXXXVER to ABCXXXXVER.org iv Remove the .tar extension from ABCXXXXVER.tar file. Upload the ABCXXXXVER TAR file to the /ONT/ directory in the OLT. A maximum of 250 files can be kept in the OLT file system. Using OLT commands, download the TAR file to the ONT. For OLT commands, refer to the 7360 ISAM FX CLI Command Guide for 100_320Gbps FD NT and FX NT, or the 7342 ISAM FTTU Operation and Maintenance Using TL1 and CLI. 2 3 Please note:

pri-cfgfile-pland/dnload or sec-cfgfile-pland/dnload can be 1 to 14 characters. pri-cfgfile-pland and pri-cfgfile-dnload should be the same name. Examples Note: X can be 1 or 2 unless specified:

i ii If pland-cfgfileX= Disabled and dnload-cfgfileX= Disabled , no file will be downloaded to the ONT. If pland-cfgfileX=FILENAME1 and dnload-cfgfileX= Disabled , FILENAME1 will be downloaded and FILENAME1 will be made active. An ONT reboot is required. iii If pland-cfgfileX=Disabled and dnload-cfgfileX= FILENAME2 166 3FE-47555-AAAA-TCZZA Issue: 01 7368 ISAM ONT G-240W-G Product Guide ONT configuration file over OMCI iv v FILENAME2 will be downloaded and FILENAME2 will be made passive. An ONT reboot is not required. If pland-cfgfileX=FILENAME3 and dnload-cfgfileX= FILENAME 4, the OLT reports an error because the filenames are not the same. Configure equipment interface pland-cfgfile1=XMLXXXXXX1 and dnload-cfgfile1 XMLXXXXXX1 Configure equipment interface pland-cfgfile2=XMLXXXXXX2 and dnload-cfgfile2 XMLXXXXXX2 Although the OLT permits the above two steps without reporting an error, Nokia does not recommend executing them, because the ONT may exhibit unexpected behavior. vi If pland-cfgfileX=Auto and dnload-cfgfileX= Auto The OLT will download the XML file from "sw-ctr-list" (configure equipment ont sw-ctrl) 4 STOP. This procedure is complete. The ONT will distribute the configuration files to the different services based on the active indication from the OLT and on the Nokia defined index. The ONT automatically reboots to apply the configuration files. After the ONT reboots and reports the active version, the OLT completes the file download procedure. Operators must check the committed file from the OLT to verify whether the corresponding file has been applied. If an error occurs, contact Nokia for support. Issue: 01 3FE-47555-AAAA-TCZZA 167 ONT configuration file over OMCI 7368 ISAM ONT G-240W-G Product Guide 168 3FE-47555-AAAA-TCZZA Issue: 01 Customer document and product support Customer documentation Customer Documentation Welcome Page Technical Support Customer Documentation Technical Support Documentation feedback Customer Documentation Feedback Copyright 2018 Nokia. 3FE-47555-AAAA-TCZZA

2ADZRG240WGExternalPhoto Adapter 1 Adapter 2 Adapter 3 Adapter 4 Adapter 5 Adapter 6 Adapter 7

-0.2 59.5mm This device complies with Pa

(Operation is subject to the falling two conditions:

(A) this devee may not cause harmful interference, nd

(2) this device must accept any interference received, Incing interference that may cause undesied operation. DANGER- Invisible Laser radiation when open

[AVOID OIRECT EXPOSURE TO BEAM DDANGER- Rayonnement laser invisible lorsqu'elie fest ouverte, fvtexFexpositon direct au faiseau, 2301 Sugar Sush Re Raleigh, Noz7612 Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No.50,dated June 24,2007. NOKIA 12v0c === 3A, ASSEMBLED IN CHINA, FE FCCID:2ADZRG240WG LTE. Cc US sere Intertek 4006119

= 39.5mm >

C2 Mal oad

NOKIA Shanghai Bell CO. Ltd. Letter of Authorization Company: NOKIA Shanghai Bell CO. Ltd. Address: No. 388, Ningqiao Rd. Pilot Free Trade Zone, Shanghai, China Product Name: 7368 ISAM ONT Model Number(s): G-240W-G Product Description: 7368 ISAM ONT We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc.is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: 2018-10-16 Name:

Liguo Leng Hardware Consultant Engineer Title:

Company: NOKIA Shanghai Bell CO. Ltd.

NOKIAShanghaiBellCO.Ltd. Request for Confidentiality Date: _2018-9-12_ Subject: Confidentiality Request for: _____ FCCID: 2ADZRG240WG_______ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent*1 Permanent Permanent Permanent Permanent Permanent*

Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BOM software security requirement Schematics Test Setup Photos Users Manual

*Note: ______(Insert Explanation as Necessary)______ ____ NOKIA Shanghai Bell CO. Ltd._____ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TCB in the event information regarding the product or the product is made available to the public. TCB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, Liguo Leng

(Print name) By:

(Signature/Title2)

NOKIA Shanghai Bell CO. Ltd. FCC Software Configuration Control Declaration Date: October 19, 2018 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Product/ Model Number: G-240W-G Regarding FCC Country Code Selection guidelines identified in KDB 594280. All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Signature:

Name: Liguo Leng Company: NOKIA Shanghai Bell CO. Ltd. Telephone: 86-21-38434963 FCC Software Configuration Control Declaration Rev1.1.docx