INSTR,INSTL,GD00BLE-1 - P/N: 10026532 X8 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000 X 8.500 - TOL. +/-.125" - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2 PRINTERS INSTRUCTIONS:
1 PRODUCT DESCRIPTION GD00BLE-1 Summary of Operation GD00BLE-1 connects to the garage door openers pushbutton wall console terminals. A wireless tilt sensor mounts on garage door and reports doors position to GD00BLE-1. Please download the Walmart InHome app from the Apple or Android PlayStore. 2 SAFETY NOTES WARNING GD00BLE-1 EXCLUSIVELY FOR WALMART GARAGE DOOR OPENER REMOTE COMMAND TRANSCEIVER with TILT SENSOR Installation Instructions 3 PRODUCT COMPONENTS STATUS INDICATOR POWER INPUT JACK CONNECTION WIRES OPTIONAL ADJUSTABLE GD00BLE-1 MOUNTING BRACKET GD00BLE-1 uses BLE for communication to open or close the garage. A warning indicator light flashes and a beeper sounds for 5 seconds before the door begins to move. If the door does not completely open or close, a second open or close command can be sent after 30seconds. If the door does not completely open or close after the second attempt, the GD00BLE-1 operation is suspended until a local garage door pushbutton is activated. Reserved for Walmart URL pointer on-boarding text and QR Code Available if needed Reserved for HomeKit QR Code and label GD00BLE-1 WARNING LIGHT 4 TILT SENSOR INSTALLATION AND BATTERY 1 To activate the tilt sensor, remove the battery protection pull strip LINK BUTTON MOUNTING SCREWS AND ANCHORS FOR GD00BLE-1 2 Attach the mounting plate to the top panel of the door 3 Snap the sensor onto the mounting plate ARROWS ON PLATE
& SENSOR POINT UP
"UP"
ARROWS POST ON BOTTOM WIRE TIES Use double sided tape or the two mounting screws supplied
(drill 1/16" pilot holes if required) The system will notify you when the battery is low, replace the battery with a type CR2032 coin cell LOW BATTERY REPLACEMENT 2 PLUS SIDE UP !!!
CR2032 Insert the battery into the transmitter POWER SUPPLY SCREW AND MOUNTING HARDWARE FOR ADJUSTABLE BRACKET TILT SENSOR SCREWS AND MOUNTING TAPE FOR TILT SENSOR This operator system is equipped with an unattended operation feature. This door could move unexpectedly. NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING This system can be installed on sectional type doors only per
(UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING The Remote Command Transceiver must be mounted in the garage, in sight of the garage door, where the visual and audible movement warning indicators can be clearly seen and heard. WARNING Do not install the Remote Command Transceiver on garage door operators manufactured prior to 1993 (models without an operational safety beam entrapment detection system). 5 PAIRING TILT SENSOR & RESETTING TO FACTORY DEFAULTS WALL OUTLET POWER SUPPLY GD00BLE-1 POWER INPUT JACK LINK BUTTON The GD00BLE has already been set to factory defaults and pre-paired with the tilt sensor. NO RESET OR PAIRING IS REQUIRED. The following instructions are provided for reference only Quickly pressing the LINK button 5 times will reset the GD00BLE to the factory defaults (Tilt pairing will be preserved). Long pressing with LINK button (3-5 seconds) until an audible beep is heard will re-pair/learn the Tilt Sensor. 1 To open the case, twist a small screwdriver in case slot SLOT Reserved for Bluetooth QR Code 6 GD00BLE-1 MOUNTING Tilt sensor mounted on the top panel of the door The GD00BLE-1 typically mounts on the ceiling near the opener and the power outlet
! WARNING !
REMOVE POWER FROM THE GARAGE DOOR OPENER BEFORE CONTINUING THE GD00BLE-1 WARNING LAMP MUST BE VISIBLE IN ALL DOOR POSITIONS 1 Use the four screws and anchors to mount the GD00BLE-1 above the opener 3/16" HOLES FOR ANCHORS 9 OPERATION NOTES 1. The warning light will flash and the warning beeper will sound for five seconds before the door opener is activated. STAY CLEAR OF THE DOOR AND DOOR OPENER. THEY ARE ABOUT TO MOVE!
2. If the door does not completely open or close after remote activation, the GD00BLE-1 will allow user to try to operate the door one more time. If the second attempt fails, the GD00BLE-1 will go into lock-out mode. 3. If the GD00BLE-1 is in lock-out mode and will not accept remote commands, activate the door from the pushbutton wall console. 4. Once the GD00BLE-1 has initiated the movement of the garage door, another command cannot be sent for 30 seconds. This eliminates the chance of bouncing the garage door and possibly damaging the garage door opener. Strobe: 360 Lumens Communications: Bluetooth Audible Alarm: 85 db @ 10 feet GD00BLE-1 Specifications Power Supply: Input: 120 VAC, 0.35 A, Output: 12 VDC, 1 A Operating Temperature: -4122 F (-2050 C) Operating Temperature: -4122 F (-2050 C) Mounting to Garage Door: Double-sided tape or two mounting screws Battery Life: 24 Months (typical) Communications: Proprietary 345 MHz Tilt Sensor Specifications Power Supply: Type CR2032 Coin Cell Battery Mounting: Screws and anchors to the ceiling. Range: 100 feet line-of-sight to GD00BLE-1
(Specifications subject to change without notice) 7 GD00BLE-1 CONNECTIONS 2 Plug the power cord into the power input jack on the GD00BLE-1 1 Connect the GD00BLE-1 connection wires to the pushbutton wall console terminals on the garage door opener. The terminals may be named "PWC", "WC",
"PB", "PUSHBUTTON", or "RED and WHITE". Terminal names and locations vary by model. 3 Plug into the outlet. DO NOT DISCONNECT ANY WIRES CURRENTLY CONNECTED TO THE GARAGE DOOR OPENER !!!
Either wire can connect to either terminal USE WIRE TIES TO SECURE EXCESS WIRING CLEAR OF ALL MOVING PARTS OF THE GARAGE DOOR AND OPENER GARAGE DOOR OPENER PUSHBUTTON PUSHBUTTON 10 PROBLEM TROUBLESHOOTING POSSIBLE CAUSE CORRECTIVE ACTION Reserved for Bluetooth Connectivity Troubleshooting Obstruction blocking the door or incorrect wiring. The tilt sensor signal is not being received by the GD00BLE-1. The GD00BLE-1 flashes and beeps when activated but the door does not move. The GD00BLE-1 flashes and beeps when activated but the door does not move. 1. Make sure that there are no obstacles preventing the door from moving. 2. Make sure that the GD00BLE-1 connection wires are connected to the proper terminals on the garage door opener. Trace the wires from the garage door openers pushbutton wall console to the door opener. This is where the GD00BLE-1 connection wires should be connected. 1. Pair the tilt sensor with the GD00BLE-1 Garage Door Controller. a. Press and hold the pair button on the side of the GD00BLE-1 main unit for about 7 seconds. It will emit a short chirp. b. Release the button. c. Rotate the tilt sensor 90 degrees to trigger a transmission. A short chirp should be heard. d. If a short short chirp is not heard, rotate the tilt sensor again. 2. Make sure the tilt sensor is mounted correctly on the garage door, with the arrow pointing up. 3. Make sure the battery pull tab has been removed from the tilt sensor. 4. Replace the battery in the tilt sensor. 8 SYSTEM OPERATION & SETUP 1 2 3 4 5 6 Restore power to your garage door opener To synchronize the system, use the garage door opener's pushbutton to manually open and close the door Use the previously downloaded Walmart InHome app to congure, activate and operate your garage door. The Walmart InHome app QR code can be found in this set of instructions in panel 1. The Bluetooth QR code can be found in Panel 5. The GD00BLE-1 will beep and ash for ve seconds before the door moves The GD00BLE-1 will activate the door opener and open or close the door STAY CLEAR OF THE DOOR !!!
BEEP BEEP BEEP FLASH FLASH FLASH Optional HomeKit conguration is supported. The HomeKit app QR code can be found in Panel 1. STAY CLEAR OF THE DOOR !!!
Walmart Nortek Smart Garage Door Controller One (1) Year Limited Warranty WALMART as the seller of the Nortek Smart Garage Door Controller (the Product) provides this limited warranty against defects in materials and/or workmanship under normal use for a period of ONE (1) YEAR from the date of purchase by the original purchaser (Warranty Period). If a defect arises and valid claim is received within the Warranty Period, then as your sole remedy (and WALMARTs sole liability), WALMART will either 1) repair the defect at no charge, using new or refurbished replacement parts, or 2) replace the Product with a new product that is functionally equivalent to the original, in each case within 30 days following receipt of the returned Product. A replacement product assumes the remaining warranty of the original Product. When a Product is exchanged, any replacement item becomes your property and the replaced Product or part becomes WALMART property. Software and firmware upgrades, modifications, patches and/or new releases provided as part of the Product and InHome App Support shall not extend the One (1) Year Limited Warranty. Obtaining Service: Please contact us at 1-833-235-2111 REGULATORY NOTICES Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. Les changements ou modifications non approuvs expressment par la partie responsable de la conformit pourrait annuler lautorit de lutilisateur faire fonctionner lquipement. This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Increase the separation between the equipment and receiver Reorient or relocate the receiving antenna Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. We, Nortek Security & Control, LLC of 5919 Sea Otter Place, Carlsbad, CA 92010, declare under our sole responsibility that the device, GD00BLE-1 complies with Part 15 of the FCC rules. This device complies with Part 15 of the FCC Rules and Industry Canada license exempt standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference received that may cause undesired operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitatio n est autorise aux deux conditions suivantes:
(1) lappareil ne doit pas produire de brouillage, et
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible de n compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003 Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada KEEP AWAY FROM SMALL CHILDREN. IF BATTERY IS SWALLOWED, PROMPTLY SEE A DOCTOR. DO NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL OF USED BATTERIES MUST BE MADE IN ACCORDANCE WITH THE WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA. Copyright 2019 Nortek Security & Control LLC 10026532 X8