submitted | available | document details (if available) | source link |
---|---|---|---|
February 06 2016 | February 06 2016 | 10011739X1.indd Copyright © 2016 Nortek Security & Control Acrobat Distiller 10.1.16 (Windows) |
various | User Manual - SW-ATT-DB-Z | Users Manual | 307.72 KiB | February 06 2016 |
INSTR,INSTL,SW-ATT-DB-Z; P/N: 10011739X1; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500 x 11.000; TOL: .125; SCALE: 1-1 PRINTERS INSTRUCTIONS:
SW-ATT-DB-Z Installation Instructions PUSHBUTTON WITH ILLUMINATED RING PHILLIPS SCREWS (2) SW-ATT-DB-B PUSHBUTTON MOUNTING HOLE SW-ATT-DB-Z Door Chime Button/Sensor Product Description The AT&T model number SW-ATT-DB-Z is a fully supervised proprietary two-way 915 MHz door chime button transmitter designed to signal the DLC and ring a local door chime when its pushbutton is pressed. Two terminals in the transmitter connect to the existing household door chime wires. The transmitter is powered by the voltage present on the door chime button wires. When the transmitters pushbutton is pressed, the two terminals provide a circuit closure that activates the household door chime. Installing the Transmitter MOUNTING HOLE (2) PROTECTIVE FOAM BACKING LEARN BUTTON Mounting Door Chime Transmitter Pushbutton 4. Connect the two door chime wires to the two screw terminals inside the transmitter. Polarity is not important. Wait to close the sensor until after the discovery process. Discovering and Registering the Transmitter Follow these steps to discover and register the SW-ATT-DB-Z sensor with the customers system:
1. Use the Web tool to place the system into Discovery Mode. 2. Make the SW-ATT-DB-Z discoverable by pressing and holding the sensors LEARN button for three seconds. The signal indicator will slowly blink during discovery. The LED will turn solid for 15 seconds if discovery successfully completes. The LED will blink fast for 15 seconds if discovery fails. 3. Con rm that the SW-ATT-DB-Z sensor has been discovered by the system. If desired, edit the sensors name and/or location in the system. 4. 5. Attach the sensor to the mounting plate by inserting the two tabs on the bottom end of the mounting plate into the terminal end of the sensors top case, then snap the case closed. SCREW TERMINALS 6. Use the Web tool to place the system into Test Mode then test the sensor by pressing the sensors pushbutton. The existing household doorbell should also ring when the sensors pushbutton is pressed. SW-ATT-DB-Z Component Locations The transmitter typically mounts in the location that replaces the current hardwired door chime pushbutton. Follow these steps to install the transmitter:
1. Remove the current hardwired door chime pushbutton. Disconnect the two door chime wires and prepare them to connect to the new transmitter. 2. Twist a small screwdriver in the slot on the end of the transmitter and remove the mounting plate. 3. Route the door chime wires through the mounting plate. Be sure the arrow on the mounting plate points up and attach the mounting plate to the surface with the two screws provided. EXISTING DOOR CHIME WIRES FASTEN WIRES TO SCREW TERMINALS WITH PHILLIPS SCREWDRIVER Copyright 2016 Nortek Security & Control LLC Door Chime/Sensor Mounting Speci cations
Operating Temperature: -25 to 55 C
Operating Frequency: 915 MHz
Dimensions: 2.75 x 1.17 x 0.63 in. (6.98 x 2.97 x 1.00 cm)
External Input: 16VAC Class 2 transformer
Weight: approx. 1 oz.
Housing Material: ABS plastic
Colors: SW-ATT-DB-Z Oil-Rubbed Bronze FCC Compliance Statement This device complies with FCC Rules and Regulations as Part 15 devices as well as Industry Canada license exempt RSS Rules and Regulations. Operation is subject to the following two (2) conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Increase the separation between the equipment and receiver
Reorient or relocate the receiving antenna
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help. Any changes or modi cations not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes: (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. 10011739X1
This product uses the FCC Data API but is not endorsed or certified by the FCC