INSTR,INSTL,GD00Z-1 - LINEAR P/N: 235686 X21 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000 X 8.500 - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2 PRINTERS INSTRUCTIONS:
GD00Z-1 GARAGE DOOR OPENER REMOTE COMMAND CONTROLLER with TILT SENSOR Installation Instructions USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340 www.linearcorp.com 3. PRODUCT FEATURES CONTROLLER WARNING LIGHT STATUS INDICATOR POWER INPUT JACK CONTROLLER CONNECTION WIRES TILT SENSOR POWER SUPPLY RETAINING BRACKET DOUBLE SIDED MOUNTING TAPE, SCREWS AND ANCHORS LINK BUTTON ADJUSTABLE MOUNTING BRACKET
(OPTIONAL) POWER SUPPLY 1. PRODUCT DESCRIPTION The Model GD00Z-1 is a garage door opener Remote Command Controller with built-in Z-Wave interoperable two-way RF mesh networking technology designed for use with Lowes Iris hub. A garage door opener connected to the Controller can be remotely activated using the Iris web interface or Iris mobile applications. The GD00Z-1 Controller connects to the garage door openers pushbutton wall console terminals and communicates with the Iris hub using Z-Wave radio signals. A wireless tilt sensor mounts on the garage door and reports the doors position to the Controller. When the Controller receives a command from the Iris hub, it will open or close the garage door. Anytime the garage door opener is activated remotely by the Controller, a warning indicator ashes and a beeper sounds for ve seconds before the door begins to move. If, due to an obstruction or other cause, the door does not completely open or close when it is activated remotely, the Controller will pause for 30 seconds. After the delay, a second remote activation can be attempted. If the door does not complete its motion on the second attempt, the Controller will suspend operation until the door is operated locally with the openers pushbutton wall console. The Controller is powered by a plug-in power supply. The Model TILT 345 tilt sensor is powered by a 2032 lithium battery. If the tilt sensor battery is low, it will be reported to the Iris hub by the Controller. A link button and status light are provided on the Controller for adding or removing the device with the Iris hub. Four screws and anchors are provided for mounting the Controller. An adjustable controller mounting bracket with hardware is supplied for installing the unit onto the door openers hanging hardware. The wireless tilt sensor mounts with double sided tape or the two screws supplied. Z-Wave is a registered trademark of Sigma Designs Inc. and/or its subsidiaries. 4. TILT SENSOR INSTALLATION AND BATTERY TO ACTIVATE THE TILT SENSOR, REMOVE THE BATTERY PROTECTION PULL STRIP ARROWS ON PLATE
& SENSOR POINT UP ATTACH MOUNTING PLATE TO TOP PANEL OF THE DOOR SNAP SENSOR ONTO THE MOUNTING PLATE 2. SAFETY NOTES WARNING This operator system is equipped with an unattended operation feature. This door could move unexpectedly. NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING This system can be installed on sectional type (roll up) doors only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING The Remote Command Controller must be mounted in the garage, in sight of the garage door, where the visual and audible movement warning indicators can be clearly seen and heard. WARNING Do not install the Remote Command Controller on garage door operators manufactured prior to 1993
(models without an operational safety beam entrapment detection system). 5. PAIRING WITH IRIS WALL OUTLET www.lowes.com/iris POWER SUPPLY CONTROLLER POWER INPUT JACK LINK BUTTON
"UP"
ARROWS POST ON BOTTOM USE DOUBLE SIDED TAPE OR THE TWO MOUNTING SCREWS SUPPLIED
(DRILL 1/16" PILOT HOLES IF REQUIRED) TO PAIR WITH THE IRIS HUB TO REMOVE FROM THE IRIS HUB PARING THE CONTROLLER REMOVING THE CONTROLLER IRIS WILL NOTIFY YOU WHEN THE BATTERY IS LOW, REPLACE THE BATTERY WITH A TYPE CR2032 COIN CELL PLUS SIDE UP !!!
CR2032 INSERT THE BATTERY INTO THE TRANSMITTER TO OPEN THE CASE, TWIST A SMALL SCREWDRIVER IN CASE SLOT SLOT 1 2 3 4 FROM THE IRIS WEB SITE, CLICK
"DEVICES", THEN CLICK THE
"ADD DEVICES" BUTTON SELECT GARAGE DOOR CONTROLLER FROM THE LIST FOLLOW THE ON-SCREEN INSTRUCTIONS TO PAIR THE CONTROLLER WITH THE HUB WHEN INSTRUCTED, PRESS THE LINK BUTTON ON THE CONTROLLER 1 2 3 4 FROM THE IRIS WEB SITE, CLICK "DEVICES"
ON THE GARAGE DOOR CONTROLLER DEVICE CLICK
"MANAGE", THEN CLICK "REMOVE"
FOLLOW THE ON-SCREEN INSTRUCTIONS TO UN-PAIR THE CONTROLLER WITH THE HUB WHEN INSTRUCTED, PRESS THE LINK BUTTON ON THE CONTROLLER INSTR,INSTL,GD00Z-1 - LINEAR P/N: 235686 X21 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000 X 8.500 - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 2 OF 2 PRINTERS INSTRUCTIONS:
6. CONTROLLER MOUNTING 7. CONTROLLER CONNECTIONS 8. SYSTEM OPERATION TILT SENSOR MOUNTED ON THE TOP PANEL OF THE DOOR THE CONTROLLER TYPICALLY MOUNTS ON THE CEILING NEAR THE OPENER AND THE POWER OUTLET 2 PLUG THE POWER CORD INTO THE POWER INPUT JACK ON THE CONTROLLER THE CONTROLER'S WARNING LAMP MUST BE VISIBLE IN ALL DOOR POSITIONS THE CONTROLLER CAN ALSO BE ATTACHED TO THE OPENER'S HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET 1 CONNECT THE CONTROLLER CONNECTION WIRES TO THE PUSHBUTTON WALL CONSOLE TERMINALS ON THE GARAGE DOOR OPENER. THE TERMINALS MAY BE NAMED "PWC", "WC", "PB", "PUSHBUTTON", OR "RED AND WHITE". TERMINAL NAMES AND LOCATIONS VARY BY MODEL. 3 PLUG THE POWER SUPPLY INTO 115 VAC OUTLET AND SECURE IT WITH THE RETAINING BRACKET DO NOT DISCONNECT ANY WIRES CURRENTLY CONNECTED TO THE GARAGE DOOR OPENER !!!
3/16" HOLES FOR ANCHORS THE OPTIONAL ADJUSTABLE MOUNTING BRACKET FITS 3 WAYS ON THE CONTROLLER SECURE BRACKET WITH SCREW THE BRACKET SNAPS ONTO INDENTS ON EITHER SIDE OR ON THE END OF THE CONTROLLER INDENT INDENT INDENT EITHER WIRE CAN CONNECT TO EITHER TERMINAL BE SURE WIRES ARE CLEAR OF ALL MOVING PARTS OF THE GARAGE DOOR AND OPENER 1 2 3 USE THE IRIS WEB SITE AND MOBILE APPS TO CONTROL YOUR GARAGE DOOR, VIEW STATUS, AND SET CUSTOM RULES THE CONTROLLER WILL BEEP AND FLASH FOR FIVE SECONDS BEFORE THE DOOR MOVES THE CONTROLLER WILL ACTIVATE THE DOOR OPENER AND OPEN OR CLOSE THE DOOR 4 THE IRIS WEB PAGE OR MOBILE APP WILL SHOW THE NEW STATUS OF THE DOOR AFTER THE DOOR COMPLETES ITS CYCLE BEEP BEEP BEEP FLASH FLASH FLASH GARAGE DOOR OPENER USE THE BOLTS AND NUTS SUPPLIED TO ATTACH THE BRACKET TO A SECURE STRUCTURE BE SURE THE CONTROLLER IS CLEAR OF ALL MOVING PARTS OF THE GARAGE DOOR PUSHBUTTON PUSHBUTTON USE THE FOUR SCREWS AND ANCHORS TO MOUNT THE CONTROLLER ABOVE THE OPENER 9. OPERATION NOTES 1. The warning light will ash and the warning beeper will sound ve seconds before the door opener is activated. STAY CLEAR OF THE DOOR, AND DOOR OPENER. THEY ARE ABOUT TO MOVE!
2. If the door does not completely open or close after remote activation, the Controller will allow user to try to operate the door one more time. If the second attempt fails, the Controller will go into lock-out mode and blink the status indicator. See Note #3. 3. If the status indicator is blinking, the Controller is in lock-out mode and will not accept remote commands. Activate the door from the pushbutton wall console then check that the status indicator stops blinking. NOTICE TO USERS IN CALIFORNIA - CR COIN CELL LITHIUM BATTERY INFORMATION:
THIS PRODUCT CONTAINS A CR COIN CELL LITHIUM BATTERY WHICH CONTAINS PERCHLORATE MATERIAL - SPECIAL HANDLING MAY APPLY - SEE www.dtsc.ca.gov/hazardouswaste/perchlorate KEEP AWAY FROM SMALL CHILDREN. IF BATTERY IS SWALLOWED, PROMPTLY SEE A DOCTOR. DO NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL OF USED BATTERIES MUST BE MADE IN ACCORDANCE WITH THE WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA. Changes or modi cations not expressly approved by the manufacturer could void the users authority to operate the equipment. Les changements ou modi cations non approuvs expressment par la partie responsable de la conformit pourrait annuler lautorit de lutilisateur faire fonctionner lquipement. 10. TROUBLESHOOTING PROBLEM The Controller does not ash or beep when activated. POSSIBLE CAUSE No power to the Controller. The Controller ashes and beeps when activated but the door does not move. Obstruction blocking the door or incorrect wiring. Garage door opens or closes, but the status does not change on the Iris website or mobile app. The tilt sensor signal is not being received by the Controller. CORRECTIVE ACTION 1. Make sure the power supply is plugged in securely to a live outlet. 2. Make sure the power cord is plugged in securely to the Controller. 1. Make sure that there are no obstacles preventing the door from moving. 2. Make sure that the Controllers connection wires are connected to the proper terminals on the garage door opener. Trace the wires from the garage door openers pushbutton wall console to the door opener. This is where the Controllers connection wires should be connected to. 1. Make sure the tilt sensor is mounted correctly on the garage door, with the arrow pointing up. 2. Make sure the battery pull tab has been removed from the tilt sensor. 3. Replace the battery in the tilt sensor. STAY CLEAR OF THE DOOR !!!
LINEAR LIMITED RETAIL WARRANTY Linear LLC (the Company) warrants to the original purchaser that products delivered hereunder will be free of defects in materials and workmanship for a period of one (1) year from the date of purchase. The Company within said period shall at its option, either repair or replace free of charge, any product or part thereof found, upon the Companys inspection, to be so defective, and will return the repaired or replaced product to the purchaser at Companys expense. All products returned for warranty service require a Return Product Authorization Number (RPA#). For warranty service, shipping instructions, and an RPA#, contact Linear Technical Services at 1-855-546-3351. Devices must be sent to the Company at owners expense and be accompanied with statement of defect and proof of purchase. This warranty is conditioned on the following:
1. The Company must be noti ed within one year of purchase and have been given the opportunity of inspection by return of any alleged defective product free and clear of all liens and encumbrances to the Company or its distributor; and 2. The product must not have been abused, misused or improperly maintained and/or repaired during such period; and 3. Such defect has not been caused by corrosion or exposure to other than ordinary wear and tear. THE COMPANY MAKES NO OTHER WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. The Companys maximum liability hereunder is limited to the purchased price of the product. In no event shall the Company be liable for any consequential, indirect, incidental or special damages of any nature arising from the sale or use of the product, whether based in contract, tort, strict liability or otherwise. Note: Some states do not allow limitations on incidental or consequential damages or how long an implied warranty lasts, so that the above limitations may not fully apply. This warranty gives speci c legal rights and you may also have other rights which may vary from state to state. This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Copyright 2014 Linear LLC 235686 X21