INSTR,INSTL,DXS-36AF - LINEAR P/N: 232812 X4 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500 X 11.000 - SCALE: 1-1 - SIDE 1 OF 2 PRINTERS INSTRUCTIONS:
DXS-36AF SUPERVISED DOOR/WINDOW TRANSMITTER Installation Instructions AlarmForce Industries Inc. 675 Garyray Drive Toronto, ON M9L 1R2, Canada ALARMFORCE DXS-36AF TRANSMITTER DXS-31AF FEATURES & ACCESSORIES TRANSMITTER SCREWS AND DOUBLE STICK TAPE ADJUSTABLE MAGNET 1/2" GAP DISTANCE MAXIMUM MAGNET CAN BE MOUNTED UP TO 1/2" FROM LEFT SIDE OF TRANSMITTER MAGNET ADJUSTMENT TAB (EACH SIDE) MAGNET SCREWS AND DOUBLE STICK TAPE SQUEEZE MAGNET TABS TO ADJUST MAGNET HEIGHT (4 POSITIONS) PRODUCT DESCRIPTION The DXS-36AF is a battery powered stationary transmitter designed for use with AlarmForce receivers. Triggering the transmitter with its built-in magnetic switch or an external switch sends a digitally coded wireless signal to its companion receiver. The DXS-36AF can send ve different signals: alarm, restore, low battery, status, and tamper. The digital code format used in the transmitter features over a million possible codes. The transmitter is pre-coded at the factory to a unique system code, so no eld coding is required. The receiver must be programmed to the transmitters system code before testing and operation. Refer to the receivers instructions for details on programming. In a typical installation, the magnet is mounted on a door or window and the transmitter is mounted on the frame. When the magnet moves more than 1/2 away from the transmitter, an alarm signal is sent. When the magnet returns next to the unit, a restore signal is sent. The magnet is adjustable with four height positions. A 1/4 high magnet spacer is also supplied to snap on to the base of the magnet. Alarms and restores can also be sent from external normally closed contacts wired to the transmitters external switch input terminals. The two screw terminals are for connection to one normally closed external contact or multiple normally closed external contacts wired in series. External contacts wire through an opening in the rear of the case. An internal jumper selects which switch input to use. Selections are: internal magnetic switch only, external switch only, or both external and internal switch. Approximately every two hours, the DXS-36AF will send a status signal to the receiver. The status signal updates the receiver to the transmitters current condition. By monitoring status signals, the receiver can determine if a transmitter has a low battery or has been removed from the system. Pressing the test button on the case sends a test signal that updates the receiver with the current state of the transmitter. When the test button is pressed, the transmit indicator lights. For two minutes after the test button is pressed, the indicator will light each time the unit sends a signal. The indicator light shines through the transmitter case. The transmitter contains a feature to detect unauthorized tampering. When the transmitters case is opened, a tamper signal is sent to the receiver. The transmitter is powered from one Type 2450 3-Volt lithium battery with an expected battery life of up to 5 years. OPENING CASE REMOVE BATTERY PROTECTION STRIP PULL BATTERY STRIP TO REMOVE BATTERY PROTECTION STRIP LIFT TWIST OPEN THE CASE TOP BY TWISTING A SMALL FLAT BLADE SCREWDRIVER OR COIN IN THE SLOT ON EITHER END OF THE TRANSMITTER COMPONENT LOCATIONS TYPE 2450 BATTERY INPUT SELECT JUMPER NOTE: SIGNAL INDICATOR IS ENABLED FOR TWO MINUTES AFTER PRESSING THE TEST BUTTON LEFT OPENING DOOR TRANSMITTER MOUNTED ON DOOR JAMB EXAMPLE INSTALLATIONS SLIDING WINDOW MAGNET MOUNTED ON WINDOW FRAME MAGNET MOUNTED ON DOOR MOUNTING SCREW HOLES TAMPER DETECTOR SIGNAL INDICATOR NOTE: BE SURE TO KEEP TAMPER DETECTOR AREA CLEAR OF ANY WIRES RIGHT OPENING DOOR TRANSMITTER MOUNTED ON DOOR JAMB MAGNET MOUNTED ON DOOR TRANSMITTER MOUNTED ON WINDOW SILL DOUBLE-HUNG WINDOW TRANSMITTER MOUNTED ON WINDOW FRAME MAGNET MOUNTED ON WINDOW SASH STILE INTERNAL MAGNETIC SWITCH TEST BUTTON EXTERNAL SWITCH INPUT INSTR,INSTL,DXS-36AF - LINEAR P/N: 232812 X4 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500 X 11.000 - SCALE: 1-1 - SIDE 2 OF 2 PRINTERS INSTRUCTIONS:
TRANSMITTER MOUNTING ATTACH TRANSMITTER AND MAGNET USING THE SCREWS OR THE DOUBLE-STICK TAPE PROVIDED ADJUSTING MAGNET HEIGHT ADJUST MAGNET HEIGHT UNTIL CASE LEVELS ARE ABOUT EQUAL NOTE: ATTACHING THE TRANSMITTER WITH DOUBLE-STICK TAPE IS NOT ALLOWED IN UL INSTALLATIONS MAGNET TRANSMITTER CASE BOTTOM THE SNAP-ON MAGNET SPACER CAN BE USED TO ADD 1/4" HEIGHT TO THE MAGNET (SPACERS CAN ALSO BE SNAPPED TOGETHER FOR MORE LIFT) OPTION JUMPER POSITIONS CONNECTING EXTERNAL CONTACTS JUMPER ON 2 & 3 SELECTS EXTERNAL SWITCH TERMINALS JUMPER ON 1 & 2 SELECTS INTERNAL MAGNETIC SWITCH NO JUMPER SELECTS BOTH THE INTERNAL MAGNETIC SWITCH AND THE EXTERNAL SWITCH TERMINALS WIRE EXTERNAL NORMALLY CLOSED CONTACTS TO THE SCREW TERMINALS WIRE MULTIPLE EXTERNAL CONTACTS IN SERIES INTERNAL EXTERNAL BOTH PLACE JUMPER ON PINS 2 & 3 FOR EXTERNAL CONTACT ONLY REMOVE THE JUMPER TO USE BOTH INTERNAL AND EXTERNAL CONTACTS NOTE: THE INTERNAL AND EXTERNAL CONTACTS ARE IN SERIES. BOTH NEED TO BE CLOSED TO RESTORE THE TRANSMITTER REMOVE SEALING PLUG AND ROUTE WIRES THROUGH SLOT IN BOTTOM OF CASE PROGRAMMING RECEIVER CHANGING THE BATTERY NOTE: THE CASE MUST BE CLOSED TO LEARN INTO THE RECEIVER
(IT WON'T LEARN IN IF TRANSMITTER IS IN TAMPER MODE) OPEN DOOR, THE TRANSMIT INDICATOR SHOULD LIGHT 1. PLACE RECEIVER INTO PROGRAM OR "LEARN" MODE 2. PRESS THE TRANSMITTER'S TEST BUTTON 3. ACTIVATE TRANSMITTER BY OPENING DOOR OR WINDOW 4. VERIFY THAT THE RECEIVER ACCEPTED THE SIGNAL 5. REPLACE TRANSMITTER COVER WHEN FINISHED NOTE: THE TRANSMIT INDICATOR WILL ONLY LIGHT DURING TRANSMISSIONS FOR TWO MINUTES AFTER PRESSING THE TEST BUTTON WHEN THE SYSTEM INDICATES A LOW BATTERY FOR THE TRANSMITTER, REMOVE THE OLD BATTERY AND REPLACE IT WITH A FRESH TYPE 2450 3-VOLT COIN CELL BATTERY TEST THE SYSTEM AFTER CHANGING THE BATTERY BE SURE TO INSTALL THE BATTERY WITH THE PLUS SIDE UP !!!
The radios are required to comply with IC Rules and Regulations. As such, they have limited transmitter power and therefore limited range.
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.
Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help Any changes or modi cations not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device conforms to Industry Canadas rules. Any changes to the equipment, not expressly approved by Linear LLC, could void the users authority to operate the equipment. Cet appareil est conforme aux rglements de lIndustrie Canada. Tout changement lquipement, sans le consentement exprs de Linear LLC, peut rsulter lannulation de lautorit con e lusager doprer cet quipement. Copyright 2012 232812 X4