INSTR,INSTL,CX-65; LINEAR P/N: 235121X2 - INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 11.000 x 8.500; SCALE: 1-1 PRINTERS INSTRUCTIONS:
CX-65 Alarm Transmitter Installation Instructions USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340 www.linearcorp.com 1. PRODUCT DESCRIPTION The Model CX-65 is a water resistant, emergency alarm transmitter designed for use with Alert One Response Link format receivers. This transmitter features a large, easy to nd, HELP button. An optional blank face aqua colored button is included for custom labeling or alternate uses. Pressing the button activates the transmitter and sends a digitally coded wireless signal to its companion receiver. To insure sending a complete signal, press the transmitter button for a minimum of two seconds. The transmitter can be wall mounted using the integral snap-on mounting bracket, or simply be placed on a table. Four rubber feet are supplied for table-top use. The CX-65 is factory set to a unique code, so no eld coding is required. The transmitter can send a signal for up to 3 seconds per activation. The green operation indicator lights when the transmitter is activated. Every two hours the transmitter tests for low battery If the battery tests low, a low battery signal is sent to the receiver. Each transmitter is sealed to provide water-resistance. The transmitter is powered by one 2032 coin-cell battery and must be disassembled to replace the battery. Before system testing and operation, each transmitter must be programmed into its receiver. Refer to the receivers or Consoles instructions for details on programming transmitters into the system. 2. FEATURES CX-65 TRANSMITTER TRANSMIT INDICATOR OPTIONAL BLANK AQUA BUTTON MOUNTING PLATE ACTIVATION BUTTON TABLE-TOP FEET (4) MOUNTING SCREWS (2) 3. OPTIONAL WALL MOUNTING 4. PROGRAM TRANSMITTER INTO RECEIVER 5.TESTING TRANSMITTER ATTACH WALL MOUNT BRACKET WITH TWO SCREWS HOOK TOP OF TRANSMITTER ONTO THE BRACKET TABS SWING TRANSMITTER ONTO BRACKET FOR NON-WALL MOUNT APPLICATIONS, STICK THE FOUR ADHESIVE "FEET"
ONTO THE MOUNTING BRACKET TO REMOVE TRANSMITTER PRESS TAB ON BRACKET 6. BATTERY REPLACEMENT OR BUTTON EXCHANGING 7. NOTES TWIST A COIN OR SCREWDRIVER IN THE SLOT ON TOP OF TRANSMITTER TO OPEN THE CASE REMOVE THE CASE TOP, BUTTON, SILICONE SEAL, AND LIFT OUT THE TRANSMITTER CIRCUIT BOARD 1 2 3 REPLACE THE BATTERY WITH ONE TYPE MAXELL CR2032 200mA HR OR DURACELL DL2032 COIN-CELL BATTERY PLUS SIDE AWAY FROM THE CIRCUIT BOARD 4 RE-ASSEMBLE THE UNIT BY REVERSING THE STEPS 5 TEST THE TRANSMITTER AFTER RE-ASSEMBLING 1 2 PLACE THE CONSOLE OR RECEIVER INTO PROGRAMMING MODE ACTIVATE THE TRANSMITTER TO PROGRAM IT INTO THE CONSOLE OR RECEIVER Alert 1 RESET TEST EMERGENCY ALARM STATUS ALERT 1 CONSOLE 1 2 PLACE THE CONSOLE OR RECEIVER INTO TEST MODE ACTIVATE THE TRANSMITTER, VERIFY THAT THE SIGNAL WAS RECEIVED NOTE: TO VERIFY THE RADIO RANGE, BE SURE TO TEST THE TRANSMITTER FROM THE INTENDED MOUNTED OR TABLE-TOP LOCATION TEST SYSTEM WEEKLY!
Alert 1 RESET TEST EMERGENCY ALARM STATUS ALERT 1 CONSOLE LINEAR LIMITED WARRANTY This Linear product is warranted against defects in material and workmanship for twelve (12) months. This warranty extends only to wholesale customers who buy direct from Linear or through Linears normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealers warranty, if any. There are no obligations or liabilities on the part of Linear LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or pro t, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for tness, are valid only until the warranty expires. This Linear LLC Warranty is in lieu of all other warranties express or implied. All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details. IMPORTANT !!!
Linear radio controls provide a reliable communications link and ll an important need in portable wireless signaling. However, there are some limitations which must be observed. For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range. A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings. Changes or modi cations to the device may void FCC compliance. Infrequently used radio links should be tested regularly to protect against undetected interference or fault. A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users. Copyright 2013 Linear LLC 235121 X2