Fortin or iDatalink Bypass Module Receiver/Control Center(RCC) Pink: (+) Ignition 1 Input/Output Red: +12V Input Violet: Starter Output Pink /White: Ignition 2 Output Orange: Accessory Output Red: +12V Input 30A 30A 15A Red: +12V Battery Power Brown: (+) Siren Black: System Main Ground White: Parking Light Relay Output White: Parking Light Relay Power Input 10A Blue: - Negative Door Unlock Output Green: - Negative Door Lock Output 16 15 14 13 12 11 10 9 16 Pin Accessory Harness Wiring:
5678 4 3 2 1 Quick Reference Install Guide REMOTE START with SECURITY & KEYLESS ENTRY SYSTEM Mounting the Receiver/Control Center (RCC):
Menu #1 (Default in Bold) 1. Choose a location on the upper or sides of the vehicle windshield. Chirps A higher location is best. Item Feature 1 2 3 4 5 6 7 8 9 FOR PROFESSIONAL INSTALLATION ONLY!
If you are not proficient in the installation of this product or would like a full ver-
sion of the installation manual, please visit our web site @www.magnadyne.com 2. Remove the backing liner from the mounting tape on the backside of the RCC and stick it to the windshield glass. 3. Route the RCC cable to the location of the control module. Programming System Features:
All CARBINE remote start systems have a menu of features that can be programmed to suit the installation requirements of any vehicle. These features can be set by using the RCC button Feature Programming procedure or by Windows PC programming and the CARBINE web app. Feature Programming by RCC Button 1. Open the drivers door. 2. Turn the ignition key ON then OFF. 1 2 3 4 5 6 7 8 9 Data Protocol ADS Fortin Confirmation Chirps On Off System Arming Active Passive Door Locking Mode Forced Passive Arming Ignition Key Controlled Locking Ignition Key Controlled Unlocking Panic with Ignition On Armed While Driving Active Passive On Off Off On Off On Off Off 0.8 sec 20 ms On On 3.5 sec 30 ms 3. Within 5 seconds, press and hold the RCC button to select the menu.
- A single chirp indicates Menu #1.
- Hold the button longer for two chirps. You are in menu #2. 10 Door Lock Pulse 11 Horn Output 0.4 Sec 40 ms 50 ms Panic Only 16 PIN
(see chart)
- Continue holding the RCC button for three chirps. You are in menu #3. 4. When the desired menu is reached, release the RCC button. 12 Comfort Closure Off CC1 CC2 13 Tilt Sensor Adjust 3*
1.5*
Off Pin Color Function Function Color Orange Green/White
(-) Factory Alarm Re-Arm Output
(-) GND When Armed/Lock while the
= 2 Chirp setting. 1 2 3 4 5 6 7 8 Blue Brown Green Violet Gray
(-) Hood Pin Safety Input Red/White
(-) Channel 3 Output (Trunk) Black/White
(-) Parking Brake Input Lt. Purple/Yellow
(-) Starter Output
(-) Trunk Trigger Lt. Green/Black
(-) Factory Alarm Disarm Output
(-) Door
(+) Door Dk. Blue Ground While Running Orange/White
(-) Accessory Output Lt. Violet/White Tach Input (AC) Pink
(-) Ignition Output Pin 9 10 11 12 13 14 15 16
(+) Vehicle Brake Safety Input Brown/Black
(-) Horn 9. The horn/siren will chirp indicating which setting is selected. 5. Within 5 seconds, press and release the RCC button the number of times corresponding to the feature you want to change then press and hold the button once more to lock the feature. The siren / horn will chirp to match the feature selected. Release the RCC button. Menu #2 (Default in Bold) Item Feature Chirps 3 4 5 6 7 8 9 Note: RCC switch pushes are sequential. For example, if you start at feature #1, then push and release the valet switch 2 more times, you will be at feature #3 and so on. Always remember to push and hold the valet switch one more time after each selection to lock the feature before using the transmitter to change the setting. 6. Use the or buttons on the CARBINE remote to adjust the feature. 7. For features with only two options, the
= 1 Chirp setting, 8. For features with more than two settings, the button selects the settings in ascending order. Press and release the times necessary to adjust the feature. button as many 10. Turn the ignition key to ON to exit feature programming. 1 Pulse 2 Pulses 3 Pulses 4 Pulses 5 Pulses 1 On On On Off Off Progressive Door Trigger Nuisance Pre-
vention Circuit Valet Switch Pulse Count for Override Door Trigger Error Chirp Double Pulse Lock Double Pulse Unlock 2 Off Off Off On On Siren Duration 30 sec 60 sec Factory Alarm Disarm with Trunk Release Factory Alarm Disarm Pulse On Off Single Double 1 2 3 4 5 6 7 8 9 10 Factory Alarm Disarm With Unlock Before Unlock Remote Start Only Menu #3 (Default in Bold) Item Feature Chirps 1 2 3 4 5 6 7 8 9 Transmission Type Automatic Manual Engine Checking Mode Wireless Tach Voltage Wired Tach Off Wireless Tach Learning 1. After the installation is completed, use the CARBINE key fob and initiate the remote start sequence. 2. If the engine does not start on the first attempt, let the CARBINE module cycle and attempt to start the engine again. Up to (3) cranking attempts may be needed to start and run the engine. 3. When the engine starts and runs, let it run for at least 30 seconds. 4. Use the CARBINE key fob to shut down the engine. Cranking Duration 0.6 Sec 0.8 sec 1.0 sec 1.2 sec 1.4 sec 1.6 sec 1.8 sec 2.0 sec 4.0 sec Wireless Tach is programmed. 1 2 3 4 5 6 7 8 9 Remote Start Run Time 12 Minutes 24 Minutes 60 Minutes Timer 15 sec Timer 35 sec Timer 45 sec Off Off On Diesel Start Delay ACC Output During Diesel Wait to Start 2nd Ignition Behavior Parking Light Behavior Ignition 1 Accessory Constant Flashing Timer Mode Run Time 12 Minutes 3 Minutes 6 Minutes 9 Minutes 10 Turbo Timer Run Time 1 Minute 3 Minutes 5 Minutes 10 Minutes Hardwire Tach or Data Tach
- Hardwire Tach requires the Lt.Violet/White wire to be connected to a fuel injector wire or a coil wire.
- Check the data bypass module spec to make sure it will provide a data tach signal. Additional pre-programming of the data module may be required. Refer to the data module instructions. To learn the tach signal 1. Start the vehicle with the key. 2. Within 5 seconds, press and hold the valet button on the RCC. 3. Once the tach signal is learned, the blue LED on the RCC will
- When tach learning from a hardwire connection, the parking light or flash. lights will flash one time
- When tach learning via the data module, the parking lights will Note: Depending on the data bypass module used, you may have to put the bypass module into tach learning mode first before performing the above procedure. Review the instructions of the data bypass module before proceeding. Pairing a Remote Controller:
Your CARBINE system remote controls are already paired to the control module. If you are replacing or adding remotes to your system, they must be programmed (paired) to the control module before they will operate the system. In order to perform remote control pairing, you must know where your Valet Button is located as you will use the button and the LED indica-
tor to perform the pairing function. Remote Pairing Procedure 1. Open the drivers door. 2. Insert the ignition key into the key cylinder. Turn ON the ignition key. 3. Press and release the valet button then press and hold the valet button for 1.5 seconds. The LED flashes and the horn/siren chirps (if connected). Release the valet button. The system is now in pairing mode and will stay in Pairing mode for 60 seconds. button on the new remote control. 5. Press and hold the 6. Press and release the A. The LED on a 4 button transmitter will begin to flash slowly. B. The word (PAir) will be displayed in the clock area of a button 5 times. 5 button LCD transmitter. The remote will remain in this state for 15 seconds. 7. Press and release the button on the new transmitter. The horn/siren chirps 1 long chirp. The new remote is programmed. 8. Turn the ignition key to the Off position. A long chirp from the horn confirms that the pairing mode is off. Note: Your CARBINE security system will accept codes from up to
(4) transmitters. Access another feature within the same menu 1. Press and release the RCC Button the number of times to advance from the last feature programmed to the next feature to be programmed. flash two times. 2. Press the RCC button and hold it. 3. Use the CARBINE remote and follow steps 5 or 6 above to adjust the feature. Access another menu 1. Press and hold the RCC Button 2. After 3 seconds, the system will advance to the next menu and conform with chirps and LED flashes. Exiting the feature program mode 1. Set the ignition key to ON. A long confirmation chirp will be hear if a horn or siren is connected. 2. Automatic after 30 seconds with no input from the RCC button
(long chirp). 3. The RCC button has been press too many times (long chirp). Feature Programming by PC/App 1. A windows computer with internet support is required. The APP supports Windows 7 (sp1) thru Windows 10 (Apple/Mac computers are not supported) 2. The programming adaptor model #ALA-21P is required 3. Follow the instructions provided with the ALA-21P accessory. Engine Checking Mode:
The engine checking mode on all CARBINE remote start systems is set at Wireless Tach by default. Once all the wiring is complete and correct, the engine can be remote started without any other changes. Engine type, Extreme weather etc. may require a more defined type of engine checking for reliable operation. Use the information enclosed to setup alternate engine checking modes. Remote Start Shutdown Diagnostics If the remote starter activates but the engine fails to remain running, a diagnostic procedure can be run to try and determine where the fault in the system is. To Perform Shutdown Diagnostics 1. With the ignition key Off, press and hold the RCC button. 2. While holding the RCC button, turn the ignition key On then Off. 3. Release the RCC button. 4. Press and release the RCC button one time. The RCC LED will report the last shutdown reason for 1 minute or until the ignition key is turned On again. Compare the LED flashes to the chart below. Status LED Flashes Reason for Shutdown 1 2 3 4 5 6 7 9 10 11 Over-Rev Shutdown Runtime Expired Shutdown by Transmitter (or Optional Push button) Low or No RPM Detection Hood Open Shutdown
(+) Brake Shutdown
(-) Parking Brake Shutdown Low Vehicle Battery (Voltage Checking Mode Only) Wait-to-Start Alarm Trigger During Remote Start Programming the Digital Shock Sensor:
Follow the enclosed procedure to set the sensitivity of the digital shock sensor. Note: The pre-warning sensitivity adjusts in proportion to the shock sensitivity. 1. Set the system in disarmed mode. 2. Turn the ignition key ON/OFF 3 times (ending in off). 3. Within 5 seconds, press buttons together for 2 seconds. The horn/siren will emit (1) long chirp to indicate you are in Shock Sensor Sensitivity Adjustment Mode.
4. To increase sensitivity, press the button. Each time you press the button you will hear (1) chirp. When you reach the MAX level adjustment, you will hear 1 short + 1 long chirp. 5. To decrease sensitivity, press the button. Each time you press the button you will hear (2) chirps. When you reach the MIN level adjustment, you will hear 2 short + 1 long chirp. 6. The shock sensor has 20 steps available for adjustment. The default setting is 10. 7. To return the shock sensor back to its default setting, button. You will hear 3 chirps. press and release the 8. During the process you can test by knocking:
1short chirp - prewarn; 1 Long chirp - TRIGGER To exit the Shock Sensor Sensitivity Adjustment Mode, turn the ignition key on. You will hear 3 long chirps. Reset and Deletion If the programmable features need to be reset to default or the Wireless Tach feature needs to be reset for re-programming, follow the enclosed procedure. 1. Open the drivers door. 2. Turn the ignition key to the ON position 3. Within 5 seconds, press and release the RCC button the number of times required below to perform the task.
- Press and release the RCC button two times to delete all of the programmed remote controls.
- Press and release the RCC button three times to delete all features programming back to their default settings. Note: This procedure does not erase Wireless Tach information.
- Press and release the RCC button four times to erase all pre-learned Wireless Tach information. 4. Once you have selected the function you want to perform, press and hold the RCC button. The RCC LED will flash and the horn will chirp
(if connected) to confirm the functional step chosen. Do Not release the button. 5. Press and release the button of a programmed remote. The horn will chirp to confirm the feature has been reset/deleted. 6. Release the RCC button and turn off the ignition key. The horn will chirp (if connected) to confirm exit. Magnadyne Corporation 1111 W. Victoria Street Compton CA 90210 (310) 735-2000 For Warranty Information: Please Visit Our Website at www.magnadyne.com IM_QS-55CSR