Programmable Features PROGRaMMInG FEatURES Step 1 Turn the ignition key ON, then OFF Step 2 Within 5 seconds of step 1, press the valet switch 5 times to access features
~ The built in beeper will sound and the status light will turn on. Step 3 Within 10 seconds of step 2, press the valet switch the number of times cor-
responding with the desired features number.
~ The built in beeper will chirp equal to the selected feature. Step 4 for RF-50-EDP & RF-30-EDP Change the feature by pressing the transmitter button that corresponds with the desired setting. Step 4 for RF-10-EDP Turn the ignition key back ON, some brake circuits require ignition power to operate. Change the feature by pressing the brake pedal the number of times that corresponds with the desired setting.
~ The built in beeper will chirp equal to the selected setting. Step 5 If you wish to change more features, repeat steps 3 & 4 at this time. Step 6 To exit programming, turn the ignition key ON then OFF. Or, you can wait 10 seconds for programming mode to expire. RF-50-EDP / RF-30-EDP / RF-10-EDP Range Extender / OEM Upgrade Kit Feature Programming: Ignition on, off, press valet 5 times
# Feature Lock Button or Brake Pedal x 1 On 1 Ignition Lock/Unlock On 2 Last Door Locking 3 Automatic Relocking On 4 Unlock w/ Trunk Release On 5 Remote Start Activation 1 press Unlock button or Brake Pedal x 2 Lock only Off Off Off 2 presses Trunk button or Brake Pedal x 3 Unlock only START button or Brake Pedal x 4 Off Enhanced 3 presses 4 presses Installation Guide Programming transmitters/Controllers Installation Overview Step 1 Have all transmitters which are to operate the system at hand. Then, turn the ignition on. Step 2 Within 5 seconds of turning on the ignition, press the Valet Switch 5 times. The beeper in the antenna will briefly sound, confirming that for the next 10 seconds the system is ready to learn a transmitter/controller code. Step 3 2-way and 4-button controllers: Press the lock button on each transmitter one at a time. When the first controller is learned, all previous controllers are erased from memory. The transmitters other three buttons functions will automatically be assigned when the lock button is learned. 1-button controllers: Press the start button on each transmitter one at a time. When the first controller is learned, all previous controllers are erased from memory. The antenna will beep once to confirm that each was learned. NOTE: If a code is not received within a 10 second period, the learning process will automatically terminate, as indicated by a long beep. 1) Install the Omegalink RS module per the instructions provided with the chosen firmware and test for proper operation. sure they are cut/capped to prevent a short circuit. If using a T-harness - Connect one end of the ribbon harness to the 4 pin black connector on the T-harness. The T-harness will supply power and ground to the 2) Connect to the Omegalink RS module:
antenna module. the RED power and BLaCK ground wires arent used so make and connect the BLaCK wire to a good chassis ground point free of paint, grease, or dirt. This will provide power to the RF module and the Omegalink RS module. If NOT using a T-harness - Connect one end of the ribbon harness to the 4 pin black connector on the RS module. Connect the RED wire to a constant +12 volt source 3) Connect to the RF-X0-EDP antenna module:
Connect the other end of the 4 pin ribbon harness to the antenna module and test for all primary functions. 4) Mount the antenna module:
Choose a mounting location high on the windshield for best operating range. Be sure that the location will not obstruct the drivers view and is easily reached to access the valet switch. Route the ribbon harness up the A-pillar to your chosen location avoiding sharp or moving objects in the vehicle. Clean the mounting surface and attach the antenna module with the provided double-stick tape. Wiring Overview Status Lights Valet Switch RF-X0-EDP Window module/antenna:
Mount to windshield for easy access and visibility. Chassis Ground (-) Input - BLaCK
(Not required if using a T-harness) Constant 12 v (+) Input - RED
(Not required if using a T-harness) 5 AMP Input trigger Wires{
Omega Carlink Remote Start activation (-) Input - RED/WHItE Lock (-) Input - BROWn Unlock (-) Input - PURPLE/YELLOW adding Omega-Carlink Directly to RS Firmware Kit Connect the Carlink AUX outputs to these inputs and program the outputs for 1 second pulse in the installation details during activation/configuration. Visit www.omegaweblink.com/rs for more info and current vehicle applications. Omegalink module flashed with RS firmware
~ REQUIRED ~
www.caralarm.com | www.omegaweblink.com | www.wiresheet.com | www.facebook.com/omegard | 800.554.4053 IS_RF-X0-EDP 10/19/2012 FCC ID:ELVNTRLF This device complies with FCC Rules Part 15 Operation is subject to the following two conditions (1) This device may not cause harmful interference and (2) this device must accept any interference that may be received, including interference that may cause undesired operation. NOTE:The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void s authority to operate th the user equipment. e