all | frequencies |
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
Module data sheet | Users Manual | 254.36 KiB | ||||
1 2 |
|
Revised Datasheet | Users Manual | 273.91 KiB | ||||
1 2 |
|
manual | Users Manual | 678.87 KiB | ||||
1 2 | Parts List/Tune Up Info | |||||||
1 2 | Block Diagram | |||||||
1 2 | Attestation Statements | |||||||
1 2 | RF Exposure Info | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | External Photos | |||||||
1 2 | Internal Photos | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | External Photos | |||||||
1 2 | Test Report | |||||||
1 2 | Schematics | |||||||
1 2 | Test Report | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | External Photos | native | ||||||
1 2 | Internal Photos | native | ||||||
1 2 | Parts List/Tune Up Info | |||||||
1 2 | RF Exposure Info | |||||||
1 2 | Schematics | |||||||
1 2 | Operational Description | |||||||
1 2 | Test Report | |||||||
1 2 | Test Setup Photos | native | ||||||
1 2 | External Photos | native |
1 2 | Module data sheet | Users Manual | 254.36 KiB |
Advanced Information Advanced Data Sheet JN5139-xxx-Myy IEEE802.15.4/ZigBee Module Family Overview The JN5139-xxx-Myy family is a range of surface mount modules that enable users to implement IEEE802.15.4 or ZigBee compliant systems with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites. The modules use Jennics JN5139 wireless microcontroller to provide a comprehensive solution with high radio performance and all RF components included. All that is required to develop and manufacture wireless control or sensing products is to connect a power supply and peripherals such as switches, actuators and sensors, considerably simplifying product development. Three basic hardware module variants are available: JN5139-xxx-M00 with an integrated antenna, JN5139-xxx-M01/M03 with an antenna connector and JN5139-
xxx-M02/M04 with a power amplifier and LNA for extended range. Each variant can be provided pre-programmed with a ZigBee network stack (JN5139-Z01-Myy). Module Block Diagram External Antenna Ceramic Antenna Balun M00 Option Connector Balun M01/03 Option Connector Balun PA / LNA M02/04 Option XTAL JN5139 chip RAM 96kB ROM 192kB 2.4GHz Radio O-QPSK Modem RISC CPU IEEE802.15.4 MAC Accelerator Power Management 128-bit AES Encryption Accelerator 128kB Serial Flash Memory SPI 2-wire serial Timers UARTs 12-bit ADC, comparators 11-bit DACs, temp sensor Power Benefits Microminiature module solutions Ready to use in products Minimises product development time No RF test required for systems Compliant with FCC part 15 rules, ETSI ETS 300-328 and Japan ARIB STD-T66 Production volumes supplied pre-programmed with application software Applications Robust and secure low power wireless applications Wireless sensor networks, particularly IEEE802.15.4 /
ZigBee systems Home and commercial building automation Home networks Toys and gaming peripherals Telemetry and utilities Industrial systems
(e.g. AMR) Features: Module 2.4GHz IEEE802.15.4 & ZigBee compliant 2.7-3.6V operation Sleep current (with active sleep timer) 2A JN5139-xxx-M00/01/03
> 1km range M00 has on board antenna M01 has SMA connector M03 has uFl connector o Receiver sensitivity -97dBm o TX power +3dBm o TX current < 39mA o RX current < 39mA o 18x30mm JN5139-xxx-M02/04
> 4km range M02 has SMA connector M04 has uFl connector o Receiver sensitivity -100dBm o 19dBm TX power o TX current < 120mA o RX current < 45mA o 18x40.5mm Features: Microcontroller 16MHz 32-bit RISC CPU 96kB RAM, 192kB ROM 4-input 12-bit ADC, 2 11-bit DACs, 2 comparators, temperature sensor 2 Application timer/counters, 3 system timers 2 UARTs (one for in-system debug) SPI port with 5 selects 2-wire serial interface 21 GPIO Evaluation kits available with full, unlimited, Software Development Kit Industrial temperature range
(-20C to +70C) Lead-free and RoHS compliant Preliminary - JN-DS-JN5139-xxx-Myy v1.1 Jennic 2007 JN5139 Single Chip Wireless Microcontroller Jennic Contents 1. Introduction 1.1. Variants 1.2. Regulatory Approvals 2. Specifications 3. Product Development 3.1. 4. Pin Configurations 4.1. Pin Assignment 4.2. Pin Descriptions 4.3. Power Supplies 4.4. SPI Memory Connections 5. Electrical Characteristics 5.1. Maximum Ratings 5.2. Operating Conditions Appendix A Additional Information A.1 Outline Drawing A.2 Module PCB Footprint A.3 Ordering Information A.4 Tape and Reel Information:
A.4.1 Tape Orientation and dimensions A.4.2 Cover tape details A.4.3 Leader and Trailer A.4.4 Reel Dimensions:
A.5 Related Documents A.6 Federal Communication Commission Interference Statement A.7 RoHS Compliance A.8 Status Information A.9 Disclaimers A.10 Version Control A.11 Contact Details 3 3 3 4 5 5 6 7 8 8 8 9 9 9 10 10 15 16 17 17 17 18 18 19 19 20 20 21 21 22 ii Preliminary - JN-DS-JN5139-xxx-Myy v1.1 Jennic 2007 Jennic 1. Introduction The JN5139-xxx-Myy module family provides designers with a ready made component which allows IEEE802.15.4 [1]
wireless applications, including ZigBee, to be quickly and easily included in product designs. The modules integrate all of the RF components, removing the need to perform expensive RF design and test. Products can be designed by simply connecting sensors and switches to the module IO pins. The modules use Jennics single chip IEEE802.15.4 Wireless Microcontroller, allowing designers to make use of the extensive chip development support material. Hence, this range of modules allows designers to bring wireless applications to market in the minimum time with significantly reduced development effort and cost. Three basic module hardware variants are available: JN5139-xxx-M00 (standard module with on board ceramic antenna), JN5139-xxx-M01 (standard module with SMA connector for use with external antennae) and JN5139-xxx-
M02 (high RF power, improved sensitivity module for extended range applications). uFL connector variants are provided (-M03 standard power and M04 high power) for FCC approved products and for applications where a small connector size is required. Each of these modules can be supplied with a range of protocol stacks, including a simple IEEE802.15.4 protocol for point to point and star applications and a ZigBee mesh networking stack. The variants available are described below. 1.1. Variants Variant JN5139-001-M00 JN5139-Z01-M00 JN5139-001-M01 JN5139-Z01-M01 JN5139-001-M02 JN5139-Z01-M02 JN5139-001-M03 JN5139-Z01-M03 JN5139-001-M04 JN5139-Z01-M04 Description JN5139 Module (IEEE802.15.4 stack, ceramic antenna) JN5139 Module (ZigBee stack, ceramic antenna) JN5139 Module (IEEE802.15.4 stack, SMA connector) JN5139 Module (ZigBee stack, SMA connector) JN5139 Module (High Power (18.5dBm), IEEE802.15.4 stack, SMA connector) JN5139 Module (High Power (18.5dBm), ZigBee stack, SMA connector) JN5139 Module (IEEE802.15.4 stack, uFl connector) JN5139 Module (ZigBee stack, uFl connector) JN5139 Module (High Power (18.5dBm), IEEE802.15.4 stack, uFl connector) JN5139 Module (High Power (18.5dBm), ZigBee stack, uFl connector) 1.2. Regulatory Approvals All module types have been tested against the requirements of European standard ETS 300 328 and a certificate of compliance to this standard is available on request. The High Power modules with M02 suffix are approved for use in Europe with reduced output power. They must not be used with PHY_PIB_ATTR_TX_POWER set above 3 See [4]. Additionally, modules with M00, M03 and M04 suffixes have received FCC Modular Approvals, in compliance with CFR 47 FCC part 15 regulations and in accordance to FCC Public notice DA00-1407. The modules are approved for use with the following half wave dipole antenna families: EAD BKR2400 series, Antenna Factor RCT and RCL series, Centurion WCR2400 & WRR2400, GigaAnt Titanis and Nearson Models 131, 141 & 145. See Appendix A.6 for details on the conditions applying to this modular approval. The high power module variant is classified as mobile device pursuant with FCC 2.1091 and must not be used at a distance of < 20 cm (8) from any nearby people. Jennic 2007 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 3 Jennic 2. Specifications Most specification parameters for the modules are specified in JN-DS-JN513x Datasheet for JN5139 single chip wireless microcontroller, [2]. Where there are differences, the parameters are defined here. VDD=3.0V @ +25C Typical DC Characteristics Deep sleep current Sleep current Radio transmit current Radio receive current JN5139-xxx-
M00/01/03
<1uA
<2uA 40mA 40mA JN5139-xxx-
M02/04
<1uA
<2uA 120mA 45mA Centre frequency accuracy
+/-25ppm
+/-25ppm Typical RF Characteristics Receive sensitivity Max. Transmit power Transmit power at 3.6V Maximum input signal RSSI range RF Port impedance SMA/uFl connector VSWR (max) Peripherals Master SPI port with five select outputs Slave SPI port Two UARTs Two-wire serial I/F (compatible with SMbus & I2C) Two programmable Timer/Counters with capture/compare facility, Tick timer Two programmable Sleep Timers Twenty-one digital IO lines (multiplexed with UARTs, timers and SPI selects) Four-channel, 12-bit, Analogue-to-Digital converter Two 11-bit Digital-to-Analogue converters Two programmable analogue comparators Internal temperature sensor and battery monitor
-96.5dBm
-100dBm
+2.5dBm
-10dBm
-95 to -10 dBm 50 ohm 2:1 18dBm 19dBm
-15dBm
-115 to -20 dBm 50 ohm 2:1 Notes With active sleep timer CPU in doze, radio transmitting CPU in doze, radio receiving Additional +/-15ppm allowance for temperature and aging Notes Nominal for 1% PER, as per 802.15.4 section 6.5.3.3 Nominal With Vdd=3.6V For 1% PER, measured as sensitivity 2.4 - 2.5GHz 2.4 - 2.5GHz Notes 250kHz - 16MHz 250kHz - 16MHz 16550 compatible Up to 400kHz 16MHz clock 32kHz clock Up to 100ks/s Up to 100ks/s Ultra low power mode for sleep 4 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 Jennic 2007 Jennic 3. Product Development Jennic supplies all the development tools and networking stacks needed to enable end product development to occur quickly and efficiently. These are all freely available from Jennics support website: http://www.jennic.com/support/ . A range of evaluation/developer kits is also available, allowing products to be quickly breadboarded. Efficient development of software applications is enabled by the provision of a complete, unlimited, software developer kit. Together with the available libraries for the IEEE802.15.4 MAC and the ZigBee network stack, this package provides everything required to develop application code and to trial it with hardware representative of the final module. The modules can be programmed by the user, for both development and production, using Jennic supplied software. They can also be supplied ready loaded with customer defined software if required. The JN-UG-3007 Flash Loader User Guide [5], describes how to put the module into programming mode, download software onto it and to load individual MAC addresses. Access to the on-chip peripherals, MAC and ZigBee stack software is provided through specific APIs. These are described in the JN-RM-2001 Hardware Peripheral Library Reference Manual [3], JN-RM-
2002 Stack Software Reference Manual [4] and JN-RM-2014 ZigBee Application Development API Reference Manual [6]. Additional information is available on the Jennic support website. 3.1. JN5139 Single Chip Wireless Microcontroller The JN5139-xxx-Myy series is constructed around the JN5139 single chip wireless microcontroller, which includes the radio system, a 32-bit RISC CPU, ROM and RAM memory and a range of analogue and digital peripherals. The chip is described fully in JN-DS-JN513x Datasheet for JN5139 single chip wireless microcontroller [2]. Jennic 2007 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 5 Jennic 4. Pin Configurations a J1 n n e t n A ADC4 DAC1 DAC2 COMP2+
COMP2-
SPICLK SPIMISO SPIMOSI SPISSZ DIO0/SPISEL1 DIO1/SPISEL2 DIO2/SPISEL3 SPISSM SPISWP DIO3/SPISEL4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 D D V D N G A S S V 0 S T C 4 O D I
0 S T R 5 O D I
0 D X T 6 O D I
0 D X R 7 O D I
I T G 0 M T 8 O D I
P A C _ 0 M T 9 O D I
I I T G 1 M T 1 1 O D I
T U O _ 0 M T
0 1 O D I I 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 ADC3 ADC2 ADC1 COMP1+
COMP1-
DIO20/RXD1 DIO19/TXD1 DIO18/RTS1 DIO17/CTS1 DIO16 DIO15/SIF_D DIO14/SIF_CLK RESETN DIO13/TIM1_OUT DIO12/TIM1_CAP Figure 1: Pin Configuration (top view) Note that the same basic pin configuration applies for all module designs. However, DIO3/SPISEL4 and DIO2/SPISEL3 are not available with high power modules. 6 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 Jennic 2007 4.1. Pin Assignment Function Pin Signal Jennic Alternative Function ADC4 DAC1 DAC2 COMP2+
COMP2-
SPICLK Analogue to Digital input Digital to Analogue output Digital to Analogue output Comparator 2 inputs SPI master clock out SPIMISO SPI Master In/Slave Out SPIMOSI SPI Master Out/Slave In SPISSZ SPI select from module - SS0 (output) SPISEL1 SPI Slave Select1 (output) SPISEL2 SPI Slave Select2 (output) General Purpose Digital I/O DIO0 General Purpose Digital I/O DIO1 SPISEL3*
SPI Slave Select3 (output) General Purpose Digital I/O DIO2 *
SPISSM SPI select to FLASH (input) SPISWP FLASH write protect (input) SPI Slave Select4 (output) General Purpose Digital I/O DIO3*
UART0 Clear To Send (input) General Purpose Digital I/O DIO4 UART0 Request To Send (output) General Purpose Digital I/O DIO5 UART0 Transmit Data (output) General Purpose Digital I/O DIO6 SPISEL4*
Hi CTS0 t RTS0 TXD0 RXD0 UART0 Receive Data (input) TIM0GT Timer0 clock/gate (input) TIM0_CAP Timer0 capture (input) TIM0_OUT Timer0 PWM (output) TIM1GT Timer1 clock/gate (input) VDD GND VSSA 3V power Digital ground Analogue ground TIM1_CAP Timer1 capture (input) TIM1_OUT Timer1 PWM (output) RESETN Active low reset General Purpose Digital I/O DIO7 General Purpose Digital I/O DIO8 General Purpose Digital I/O DIO9 General Purpose Digital I/O DIO10 General Purpose Digital I/O DIO11 General Purpose Digital I/O DIO12 General Purpose Digital I/O DIO13 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 SIF_CLK Serial Interface clock / Intelligent peripheral clock General Purpose Digital I/O DIO14 Jennic 2007 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 7 Jennic Pin Signal Function 31 32 33 34 35 36 37 38 39 40 41 SIF_D DIO 16 CTS1 RTS1 TXD1 RXD1 COMP1-
COMP1+
ADC1 ADC2 ADC3 Serial Interface data / Intelligent peripheral data t Intelligent peripheral device select Alternative Function General Purpose Digital I/O DIO15 General Purpose Digital I/O UART1 Clear To Send (input) General Purpose Digital I/O DIO17 UART1 Request To Send (output) General Purpose Digital I/O DIO18 UART1 Transmit Data (output) General Purpose Digital I/O DIO19 UART1 Receive Data (input) General Purpose Digital I/O DIO20 Comparator 1 inputs Analogue to Digital input Analogue to Digital input Analogue to Digital input
*: These two pins are not connected for High power modules 4.2. Pin Descriptions All pins behave as described in the JN513x datasheet [2], with the exception of the following:
4.3. Power Supplies A single power supply pin, VDD is provided. Separate analogue (VSSA) and digital (GND) grounds are provided. These should be connected together at the module pins. 4.4. SPI Memory Connections SPISWP is a write protect pin for the serial flash memory. This should be held low to inhibit writes to the flash device. SPISSZ is connected to SPI Slave Select 0 on the JN5139. SPISSM is connected to the Slave Select pin on the memory. This configuration allows the flash memory device to be programmed using an external SPI programmer if required. For programming in this mode, the JN5139 should be held in reset by taking RESETN low. The memory can also be programmed over the UART by using the programming mode described in JN-UG-3007 Flash Loader User Guide [5]. For normal operation of the module and programming over the UART, SPISSZ should be connected to SPISSM. 8 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 Jennic 2007 5. Electrical Characteristics In most cases, the Electrical Characteristics are the same for both module and chip. They are described in detail in the chip datasheet. Where there are differences, they are detailed below. Jennic 5.1. Maximum Ratings Exceeding these conditions will result in damage to the device. Parameter Device supply voltage VDD Voltage on analogue pins ADC1-4, DAC1-2, COMP1+, COMP1-, COMP2+, COMP2-, SPICLK, SPIMOSI, SPIMISO, SPISSM, SPISWP Voltage on 5V tolerant digital pins DIO-DIO20, RESETN, SPISSZ Storage temperature Solder reflow temperature (According to IPC/JEDEC J-STD-020C) Min
-0.3V
-0.3V
-0.3V
-40C Max 3.6V VDD + 0.3V VDD + 2V or 5.5V, whichever is the lesser 150C 260 C This device is sensitive to ESD and should only be handled using ESD precautions. 5.2. Operating Conditions Supply VDD Ambient temperature range Min 2.7V
-20C Max 3.6V 70C Jennic 2007 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 9 Jennic Appendix A Additional Information A.1 Outline Drawing 18mm J1 a n n e t n A 30mm Thickness: 3.5mm 10 1.27 mm 2.54 mm 2.54 mm 2.79 mm JN5139-xxx-M00 Outline Drawing Preliminary - JN-DS-JN5139-xxx-Myy v1.1 Jennic 2007 Jennic 18mm 9.74mm 4.59mm 30mm 1.27 mm 2.54 mm 2.54 mm 2.79 mm Thickness: 3.5mm over can, 10.6mm at SMA connector JN5139-xxx-M01 Outline Drawing Jennic 2007 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 11 Jennic 30mm 18mm 9.76mm 6.58mm 1.27 mm 2.54 mm 2.54 mm Thickness: 3.5mm 2.79 mm JN5139-xxx-M03 Outline Drawing 12 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 Jennic 2007 Jennic 18mm 7.2mm 4.05mm 40.5mm
. 2.54 mm 1.27 mm 2.54 mm 2.79 mm Thickness: 3.5mm over can, 10.6mm at SMA connector. Note that early versions of this board will be 40mm long but the SMA connector will remain in the same location with respect to the pcb pads. JN5139-xxx-M02 Outline Drawing Jennic 2007 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 13 Jennic 40.5mm
. 2.54 mm Thickness: 3.5mm 18mm 7.2mm 3.99mm 1.27 mm 2.54 mm 2.79 mm JN5139-xxx-M04 Outline Drawing 14 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 Jennic 2007 A.2 Module PCB Footprint 18mm Jennic 1.27 mm 2.54 mm 2.54mm All Pads are 0.9mm square on 1.27mm pitch Note: All modules have the same footprint. RF note for M00 modules with ceramic antenna: No components, ground plane or tracks on any layer of the mother board should be placed within 20mm of the 3 free sides of the antenna. Tracks etc may be placed adjacent to the can, but should not extend past the can towards the antenna end of the module for 20mm from the antenna. Jennic 2007 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 15 Jennic A.3 Ordering Information Part Numbering:
JN5139 - XXX - MY1Y2 Y3 Y4 Shipping R T V Box (10 modules per pack) Tape Mounted 500pcs (00 module only) Tape Mounted 200pcs (01,02,03,04 modules only) Temp Range / Device Status D
-20C to +70C, Qualified Module Type 00 01 02 03 04 Standard Power, Ceramic antenna Standard Power, SMA connector High Power, SMA connector Standard Power, uFl connector High power, uFl connector Software Variant 001 Z01 ZigBee Stack IEEE802.15.4 Stack 16 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 Jennic 2007 A.4 Tape and Reel Information:
A.4.1 Tape Orientation and dimensions Jennic Module type:
A B JN5139-xxx-M00/03 18.4 30.4 JN5139-xxx-M01 18.4 30.4 JN5139-xxx-M02 18.5 40.5 JN5139-xxx-M04 18.5 40.9 W 44 56 56 56 F E P0 P1 P2 T Cover Tape width (W) 20.2 1.75 20.2 1.75 20.2 1.75 20.2 1.75 4.0 4.0 4.0 4.0 2.0 2.0 2.0 2.0 24.0 3.4 37.5 24.0 11.4 49.5 24.0 11.4 49.5 24.0 3.4 49.5 Tolerance 0.1 0.1 0.3 0.1
+0.1 0.1 0.1 0.1 0.1 0.1 A.4.2 Cover tape details Thickness (T) 0.061mm Surface resistivity (component side) 104 to 107 Ohms/sq Surface resistivity (component side) Non-conductive Backing type:
Adhesive type:
Sealing:
Polyester PSA Room ambient Jennic 2007 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 17 Jennic A.4.3 Leader and Trailer 300 MM A.4.4 Reel Dimensions:
300 MM Module type:
JN5139-xxx-M00 JN5139-xxx-
M01/02/03/04 A 330 1.0 330 1.0 B 2.20.5 2.20.5 C 13 0.2 13 0.2 N 100 +0.1 100 +0.1 W (min) 44.5 0.3 56.5 0.3 18 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 Jennic 2007 A.5 Related Documents
[1] IEEE Std 802.15.4-2003 IEEE Standard for Information Technology Part 15.4 Wireless Medium Access Control
(MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LR-WPANs) Jennic
[2] JN-DS-JN513x Datasheet for JN5139 single chip wireless microcontroller
[3] JN-RM-2001 Hardware Peripheral Library Reference Manual
[4] JN-RM-2002 Stack Software Reference Manual
[5] JN-UG-3007 Flash Loader User Guide
[6] JN-RM-2014 ZigBee Application Development API Reference Manual A.6 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. WARNING!
FCC Radiation Exposure Statement:
This portable equipment with its antenna complies with FCCs RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance follow the instructions below;
1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. Avoid direct contact to the antenna, or keep it to a minimum while using this equipment. This transmitter module is authorized to be used in other devices only by OEM integrators under the following condition:
The transmitter module must not be co-located with any other antenna or transmitter. Jennic 2007 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 19 Jennic As long as the above condition is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). High Power Module usage limitation The high power module variants are classified as mobile device pursuant with FCC 2.1091 and must not be used at a distance of < 20 cm (8) from any nearby people. IMPORTANT NOTE: In the event that these conditions can not be met (for certain configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user manual of the end product. The user manual for the end product must include the following information in a prominent location;
To comply with FCCs RF radiation exposure requirements, the antenna(s) used for this transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter. A.7 RoHS Compliance JN5139-xxx-Myy devices meet the requirements of Directive 2002/95/EC of the European Parliament and of the Council on the Restriction of Hazardous Substance (RoHS). A.8 Status Information The status of this Data Sheet is Advanced. Jennic products progress according to the following format:
Advanced The Data Sheet shows the specification of a product in planning or in development. The functionality and electrical performance specifications are target values and may be used as a guide to the final specification. Jennic reserves the right to make changes to the product specification at anytime without notice. Preliminary The Data Sheet shows the specification of a product that is in production, but is not yet fully qualified. The functionality of the product is final. The electrical performance specifications are target values and may used as a guide to the final specification. Modules are identified with an R suffix, for example JN5139-Z01-M00R. Jennic reserves the right to make changes to the product specification at anytime without notice. Production This is the final Data Sheet for the product. 20 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 Jennic 2007 Jennic All functional and electrical performance specifications, including minimum and maximum values are final. This Data Sheet supersedes all previous document versions. Jennic reserves the right to make changes to the product specification at anytime to improve its performance. A.9 Disclaimers The contents of this document are subject to change without notice. Jennic reserves the right to make changes, without notice, in the products, including circuits and/or software, described or contained herein in order to improve design and/or performance. Information contained in this document regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. Jennic assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work infringement, unless otherwise specified. Jennic products are not intended for use in life support systems, appliances or systems where malfunction of these products can reasonably be expected to result in personal injury, death or severe property or environmental damage. Jennic customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Jennic for any damages resulting from such use. All trademarks are the property of their respective owners. A.10 Version Control Version Notes 1st Issue of Advanced Datasheet Update to correct connector positions on drawings and typo on module numbering. 000 modules now read 001. 1.0 1.1 Jennic 2007 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 21 Jennic A.11 Contact Details Corporate Headquarters Jennic Ltd, Furnival Street Sheffield S1 4QT, UK Tel: +44 (0)114 281 2655 Fax: +44 (0) 114 281 2951 info@jennic.com www.jennic.com Jennic Ltd Japan Osakaya building 4F 1-11-8 Higashigotanda Shinagawa-ku Tokyo 141-0022, Japan Tel: +81 3 5449 7501 Fax: +81 3 5449 0741 info@jp.jennic.com www.jennic.com Jennic Ltd Taiwan 19F-1, 182, Sec.2 Tun Hwa S. Road. Taipei 106, Taiwan Tel: +886 2 2735 7357 Fax: +886 2 2739 5687 info@tw.jennic.com www.jennic.com Jennic America Inc - East Coast Office 1322 Scott Street, Suite 203 Point Loma, CA 92106, USA Tel: +619 223 2215 Fax: +619 223 2081 info@us.jennic.com www.jennic.com Jennic America Inc - West Coast Office 1060 First Avenue, Suite 400 King of Prussia, PA 19406, USA Tel: +1 484 868 0222 Fax: +1 484 971 5015 info@us.jennic.com www.jennic.com Jennic Ltd Korea 701, 7th Floor, Kunam Bldg., 831-37, Yeoksam-Dong, Kangnam-ku Seoul 135-080 Korea Tel: +82 2 552 5325 Fax: +82 2 3453 8802 info@kr.jennic.com www.jennic.com 22 Preliminary - JN-DS-JN5139-xxx-Myy v1.1 Jennic 2007
1 2 | Revised Datasheet | Users Manual | 273.91 KiB |
Data Sheet JN5139-xxx-Myy IEEE802.15.4/ZigBee Module Family Overview The JN5139-xxx-Myy family is a range of surface mount modules that enable users to implement systems using IEEE802.15.4, 6LoWPAN, JenNet or ZigBee with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites. The modules use Jennics JN5139 wireless microcontroller to provide a comprehensive solution with high radio performance and all RF components included. All that is required to develop and manufacture wireless control or sensing products is to connect a power supply and peripherals such as switches, actuators and sensors, considerably simplifying product development. Three basic hardware module variants are available: JN5139-xxx-M00 with an integrated antenna, JN5139-xxx-M01/M03 with an antenna connector and JN5139-
xxx-M02/M04 with a power amplifier and LNA for extended range. Variants are available either with a ZigBee network stack (JN5139-Z01-Myy) or supporting the other stacks (JN5139-001-Myy). Module Block Diagram XTAL JN5139 chip RAM 96kB ROM 192kB 2.4GHz Radio O-QPSK Modem RISC CPU External Antenna Ceramic Antenna Balun M00 Option Connector Balun M01/03 Option Connector Balun PA / LNA M02/04 Option Power Management IEEE802.15.4 MAC Accelerator 128-bit AES Encryption Accelerator 128kB Serial Flash Memory SPI 2-wire serial Timers UARTs 12-bit ADC, comparators 11-bit DACs, temp sensor Power Benefits
Microminiature module solutions
Ready to use in products
Minimises product development time
No RF test required for systems
Compliant with FCC part 15 rules, IC Canada, ETSI ETS 300-328 and Japan ARIB STD-
T66
Production volumes supplied pre-programmed with application software Applications
Robust and secure low power wireless applications
Wireless sensor networks, particularly IEEE802.15.4 /
ZigBee systems
Home and commercial building automation
Home networks
Toys and gaming peripherals
Telemetry and utilities Industrial systems
(e.g. AMR) Features: Module
2.4GHz IEEE802.15.4 & ZigBee compatible
2.7-3.6V operation
Sleep current (with active sleep timer) 2.6A
JN5139-xxx-M00/01/03 up to 1km range (ext antenna) M00: on board antenna M01: SMA connector M03: uFl connector o Receiver sensitivity 96dBm o TX power +2.5dBm o TX current 37mA o RX current 37mA o 18x30mm
JN5139-xxx-M02/04 up to 4km range M02: SMA connector M04: uFl connector o Receiver sensitivity -100dBm o 19dBm TX power o TX current 125mA o RX current 45mA o 18x41mm Features: Microcontroller
16MHz 32-bit RISC CPU
96kB RAM, 192kB ROM
4-input 12-bit ADC, 2 11-bit DACs, 2 comparators, temperature sensor
2 Application timer/counters, 3 system timers
2 UARTs (one for in-system debug)
SPI port with 5 selects
2-wire serial interface
21 GPIO
Evaluation kits available with full, unlimited, Software Development Kit Temperature range
-20C to +70C Lead-free and RoHS compliant JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 Jennic Contents 1. Introduction 1.1. Variants 1.2. Regulatory Approvals 2. Specifications 3. Product Development 3.1. JN5139 Single Chip Wireless Microcontroller 4. Pin Configurations 4.1. Pin Assignment 4.2. Pin Descriptions 4.2.1 4.2.2 Power Supplies SPI Memory Connections 5. Electrical Characteristics 5.1. Maximum Ratings 5.2. Reflow Profile 5.3. Operating Conditions Appendix A Additional Information A.1 Outline Drawing A.2 Module PCB Footprint A.3 Ordering Information A.4 Tape and Reel Information:
A.4.1 Tape Orientation and dimensions A.4.2 Cover tape details A.4.3 Leader and Trailer A.4.4 Reel Dimensions:
A.5 Related Documents A.6 Federal Communication Commission Interference Statement A.6.1 Antennas approved by FCC for use with JN5139 modules A.6.2 High Power Module usage limitation A.6.3 FCC End Product Labelling A.7 European R & TTE Directive 1999/5/EC Statement A.8 Industry Canada Statement A.8.1 Industry Canada End Product Labelling A.9 RoHS Compliance A.10 Status Information A.11 Disclaimers A.12 Version Control 3 3 3 4 6 6 7 8 9 9 9 10 10 10 11 12 12 17 18 19 19 19 20 20 21 21 22 23 23 24 25 25 25 26 26 27 ii JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 Jennic 1. Introduction The JN5139-xxx-Myy module family provides designers with a ready made component which allows IEEE802.15.4 [1]
wireless applications, using Jennics JenNet networking protocol or ZigBee, to be quickly and easily included in product designs. The modules integrate all of the RF components required, removing the need to perform expensive RF design and test. Products can be designed by simply connecting sensors and switches to the module IO pins. The modules use Jennics single chip IEEE802.15.4 Wireless Microcontroller, allowing designers to make use of the extensive chip development support material. Hence, this range of modules allows designers to bring wireless applications to market in the minimum time with significantly reduced development effort and cost. Three module hardware variants are available: JN5139-xxx-M00 (standard module with on board ceramic antenna), JN5139-xxx-M01 (standard module with SMA connector for use with external antennae recommended for evaluation use) and JN5139-xxx-M02 (high RF power, improved sensitivity module for evaluation of extended range applications). For volume production applications, uFL connector variants are provided (-M03 standard power and M04 high power). These devices, together with the M00 variants have FCC modular approvals. Each of these modules can be supplied with a range of protocol stacks, including JenNet for most tree and linear networks, IEEE802.15.4 protocol for point-to-point and star applications and a ZigBee mesh networking stack. The variants available are described below. 1.1. Variants Variant Description FCCID Industry Canada ID JN5139-001-M00 IEEE802.15.4 stack, ceramic antenna TYOJN5139M0 JN5139-Z01-M00 ZigBee stack, ceramic antenna TYOJN5139M0 JN5139-001-M01 JN5139-Z01-M01 JN5139-001-M02 JN5139-Z01-M02 IEEE802.15.4 stack, SMA connector - for evaluation ZigBee stack, SMA connector for evaluation High Power, IEEE802.15.4 stack, SMA connector for evaluation High Power, ZigBee stack, SMA connector for evaluation N/A N/A N/A N/A JN5139-001-M03 IEEE802.15.4 stack, uFl connector TYOJN5139M3 JN5139-Z01-M03 ZigBee stack, uFl connector TYOJN5139M3 JN5139-001-M04 High Power, IEEE802.15.4 stack, uFl connector TYOJN5139M4 IC: 7438A-CYO5139M0 IC: 7438A-CYO5139M0 IC: 7438A-CYO5139M6 IC: 7438A-CYO5139M6 IC: 7438A-CYO5139M4 IC: 7438A-CYO5139M4 IC: 7438A-CYO5139M6 IC: 7438A-CYO5139M6 IC: 7438A-CYO5139M4 JN5139-Z01-M04 High Power, ZigBee stack, uFl connector TYOJN5139M4 IC: 7438A-CYO5139M4 1.2. Regulatory Approvals All module types have been tested against the requirements of European standard ETS 300 328 v1.7.1 and a Notified Body statement of opinion for this standard is available on request. The High Power modules with M02 or M04 suffix are approved for use in Europe with reduced output power: +10dBm EIRP is the maximum permitted in Europe. They must not be used with PHY_PIB_ATTR_TX_POWER set above 50 See [3] JN-RM-2002 802.15.4 Stack API. Additionally, modules with M00, M03 and M04 suffixes have received FCC Modular Approvals, in compliance with CFR 47 FCC part 15 regulations and in accordance to FCC Public notice DA00-1407. The modules are approved for use with a number of antennase, refer to section A.6.1 for details. See Appendix A.6 for details on the conditions applying to this modular approval. The modular approvals notice and test reports are available on request. The high power module variant is classified as mobile device pursuant with FCC 2.1091 and must not be used at a distance of less than 20 cm (8) from any person. In addition, all modules have Industry Canada RSS 210 Issue 7 (June 2007) certification. Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 3 Jennic 2. Specifications Most specification parameters for the modules are specified in the chip datasheet - JN-DS- JN513x Wireless Microcontroller Datasheet, [2]. Where there are differences, the parameters are defined here. VDD=3.0V @ +25C Deep sleep current Sleep current Radio transmit current Radio receive current Typical DC Characteristics Notes JN5139-xxx-
M00/01/03 JN5139-xxx-
M02/04 1.3uA 2.6uA 37mA 37mA 1.3uA 2.6uA With active sleep timer 125mA CPU in doze, radio transmitting 45mA CPU in doze, radio receiving Centre frequency accuracy
+/-25ppm
+/-25ppm Additional +/-15ppm allowance for temperature and ageing Typical RF Characteristics Notes Receive sensitivity
-96dBm
-102dBm Nominal for 1% PER, as per 802.15.4 section 6.5.3.3 (Note 1) Maximum Transmit power
+1dBm 17.5dBm Nominal (Note 1) Maximum Transmit power [Boost Mode]
+2.5dBm N/A
(Note 1) Transmit power at 3.6V 19dBm With Vdd=3.6V Maximum input signal
+10dBm
+10dBm For 1% PER, measured as sensitivity RSSI range
-95 to -10
-105 to -20 dBm dBm RF Port impedance SMA/uFl connector 50 ohm 50 ohm 2.4 - 2.5GHz VSWR (max) 2:1 2:1 2.4 - 2.5GHz Peripherals Notes 5 selects 3 selects 250kHz - 16MHz Master SPI port Slave SPI port Two UARTs Two-wire serial I/F (compatible with SMbus & I2C) Two programmable Timer/Counters with capture/compare facility, Tick timer Two programmable Sleep Timers Digital IO lines (multiplexed with UARTs, timers and SPI selects) Four channel Analogue-to-Digital converter Two channel Digital-to-Analogue converter Two programmable analogue comparators Internal temperature sensor and battery monitor
21
250kHz - 8MHz 16550 compatible Up to 400kHz 16MHz clock 32kHz clock 19 12-bit, up to 100ks/s 11-bit, up to 100ks/s Ultra low power mode for sleep
4 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 The performance of all peripherals is defined in the JN-DS- JN513x Wireless Microcontroller Datasheet [2]
Note 1: Sensitivity is defined for conducted measurements on connectorised modules. Modules with an integrated antenna have approximately 4 dB less e.i.r.p and reciprocal receive sensitivity. Jennic Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 5 Jennic 3. Product Development Jennic supplies all the development tools and networking stacks needed to enable end product development to occur quickly and efficiently. These are all freely available from Jennics support website: http://www.jennic.com/support/ . A range of evaluation/developer kits is also available, allowing products to be quickly breadboarded. Efficient development of software applications is enabled by the provision of a complete, unlimited, software developer kit. Together with the available libraries for the JenNet networking stack, the IEEE802.15.4 MAC and the ZigBee network stack, this package provides everything required to develop application code and to trial it with hardware representative of the final module. The modules can be user programmed both in development and in production using software supplied by Jennic. They can also be supplied ready loaded with customer defined software if required. Access to the on-chip peripherals, MAC and network stack software is provided through specific APIs. This information is available on the Jennic support website, together with many example applications, user guides, reference manuals and application notes. 3.1. JN5139 Single Chip Wireless Microcontroller The JN5139-xxx-Myy series is constructed around the JN5139 single chip wireless microcontroller, which includes the radio system, a 32-bit RISC CPU, ROM and RAM memory and a range of analogue and digital peripherals. The chip is described fully in JN-DS- JN513x Wireless Microcontroller Datasheet [2]. The module also includes a 1Mbit serial flash memory which holds the application code that is loaded into the JN5139 during the boot sequence. 6 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 4. Pin Configurations Jennic a J1 n n e t n A ADC4 DAC1 DAC2 COMP2+
COMP2-
SPICLK SPIMISO SPIMOSI SPISSZ DIO0/SPISEL1 DIO1/SPISEL2 DIO2/SPISEL3 SPISSM SPISWP DIO3/SPISEL4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 41 40 39 ADC3 ADC2 ADC1 38 COMP1+
37 36 35 34 33 COMP1-
DIO20/RXD1 DIO19/TXD1 DIO18/RTS1 DIO17/CTS1 32 DIO16 31 30 29 28 DIO15/SIF_D DIO14/SIF_CLK RESETN DIO13/TIM1_OUT 27 DIO12/TIM1_CAP 0 S T C 4 O D I
0 S T R 5 O D I
0 D X T 6 O D I
D D V D N G A S S V 0 D X R 7 O D I
I T G 0 M T 8 O D I
P A C _ 0 M T 9 O D I
I T U O _ 0 M T 0 1 O D I
I I T G 1 M T 1 1 O D I
Figure 1: Pin Configuration (top view) Note that the same basic pin configuration applies for all module designs. However, DIO3/SPISEL4 and DIO2/SPISEL3 are not available on the high power modules. Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 7 Jennic 4.1. Pin Assignment Pin Signal Function Alternative Function 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 ADC4 DAC1 DAC2 COMP2+
COMP2-
Analogue to Digital input Digital to Analogue output Digital to Analogue output Comparator 2 inputs SPICLK SPI master clock out SPIMISO SPI Master In/Slave Out SPIMOSI SPI Master Out/Slave In SPISSZ SPI select from module - SS0 (output) SPISEL1 SPI Slave Select1 (output) General Purpose Digital I/O DIO0 SPISEL2 SPI Slave Select2 (output) General Purpose Digital I/O DIO1 SPISEL3*
SPI Slave Select3 (output) General Purpose Digital I/O DIO2 *
SPISSM SPI select to FLASH (input) SPISWP FLASH write protect (input) SPISEL4*
SPI Slave Select4 (output) General Purpose Digital I/O DIO3*
CTS0 RTS0 TXD0 UART0 Clear To Send (input) General Purpose Digital I/O DIO4 UART0 Request To Send (output) General Purpose Digital I/O DIO5 UART0 Transmit Data (output) General Purpose Digital I/O DIO6 RXD0 UART0 Receive Data (input) General Purpose Digital I/O DIO7 TIM0GT Timer0 clock/gate (input) General Purpose Digital I/O DIO8 TIM0_CAP Timer0 capture (input) General Purpose Digital I/O DIO9 TIM0_OUT Timer0 PWM (output) General Purpose Digital I/O DIO10 TIM1GT Timer1 clock/gate (input) General Purpose Digital I/O DIO11 VDD GND 3V power Digital ground VSSA Analogue ground TIM1_CAP Timer1 capture (input) General Purpose Digital I/O DIO12 TIM1_OUT Timer1 PWM (output) General Purpose Digital I/O DIO13 RESETN Active low reset SIF_CLK Serial Interface clock / Intelligent peripheral clock General Purpose Digital I/O DIO14 8 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 Jennic Pin Signal Function Alternative Function 31 32 33 SIF_D Serial Interface data / Intelligent peripheral data out (output) General Purpose Digital I/O DIO15 DIO 16 Intelligent peripheral device data in (input) General Purpose Digital I/O CTS1 UART1 Clear To Send (input) / Intelligent peripheral device select (input) General Purpose Digital I/O DIO17 34a RTS1 UART1 Request To Send (output) / Intelligent peripheral interrupt (output) General Purpose Digital I/O DIO18 35 36 37 38 39 40 41 TXD1 UART1 Transmit Data (output) General Purpose Digital I/O DIO19 RXD1 UART1 Receive Data (input) General Purpose Digital I/O DIO20 COMP1-
COMP1+
ADC1 ADC2 ADC3 Comparator 1 inputs Analogue to Digital input Analogue to Digital input Analogue to Digital input
*: These two pins are not connected for High power modules 4.2. Pin Descriptions All pins behave as described in the JN-DS- JN513x Wireless Microcontroller Datasheet [2], with the exception of the following:
4.2.1 Power Supplies A single power supply pin, VDD is provided. Separate analogue (VSSA) and digital (GND) grounds are provided. These should be connected together at the module pins. 4.2.2 SPI Memory Connections SPISWP is a write protect pin for the serial flash memory. This should be held low to inhibit writes to the flash device. SPISSZ is connected to SPI Slave Select 0 on the JN5139. SPISSM is connected to the Slave Select pin on the memory. This configuration allows the flash memory device to be programmed using an external SPI programmer if required. For programming in this mode, the JN5139 should be held in reset by taking RESETN low. The memory can also be programmed over the UART by using the flash programmer software provided by Jennic. This is available as part of the Software Developer kit and libraries available from Jennics support website www.jennic.com/support. To enter this programming mode, SPIMISO (pin 7) should be held low whilst the chip is reset. Once programming has finished, the chip should be reset, when it will execute the new code downloaded. For normal operation of the module and programming over the UART, SPISSZ should be connected to SPISSM. Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 9 Jennic 5. Electrical Characteristics In most cases, the Electrical Characteristics are the same for both module and chip. They are described in detail in the chip datasheet. Where there are differences, they are detailed below. 5.1. Maximum Ratings Exceeding these conditions will result in damage to the device. Parameter Device supply voltage VDD Voltage on analogue pins: ADC1-4, DAC1-2, COMP1-, COMP1+, COMP2-, COMP2+, DIO9, DIO10, SPISSM, SPISWP, SPICLK, SPIMOSI, SPIMISO, Voltage on 5v tolerant digital pins: SPISSZ, DIO0-
DIO8, DIO11-DIO20, RESETN Min
-0.3V
-0.3V Max 3.6V VDD + 0.3V
-0.3V Lower of (VDD + 2V) and 5.5V 150C 260C Storage temperature Reflow soldering temperature according to IPC/JEDEC J-STD-020C
-40C This device is sensitive to ESD and should only be handled using ESD precautions. 5.2. Reflow Profile For reflow soldering, it is recommended to follow the reflow profile in Figure 2 as a guide, as well as the paste manufacturers guidelines on peak flow temperature, soak times, time above liquidus and ramp rates. Temperature 25~160 C 160~190 C
> 220 C 230~Pk. Pk. Temp
(235C) Target Time (s) 90~130 30~60 20~50 10~15 160~270 Figure 2: Recommended solder reflow profile 10 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 5.3. Operating Conditions Supply VDD Ambient temperature range Min 2.7V
-20C Jennic Max 3.6V 70C Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 11 Jennic Appendix A Additional Information A.1 Outline Drawing 18mm J1 a n n e t n A 30mm 1.27 mm 2.54 mm 2.54 mm 2.76 mm Thickness: 3.5mm Figure 3 JN5139-xxx-M00 Outline Drawing 12 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 Jennic 18mm 9.74mm 4.59 mm 30mm 1.27 mm 2.54 mm 2.54 mm 2.76 mm Thickness: 3.5mm over can, 10.8mm at SMA connector Figure 4 JN5139-xxx-M01 Outline Drawing Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 13 18mm 9.76mm 6.58 mm Jennic 30mm 1.27 mm 2.54 mm 2.54 mm 2.76 mm Thickness: 3.5mm Figure 5 JN5139-xxx-M03 Outline Drawing 14 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 Jennic 18mm 7.2mm 4.32 mm 41mm 1.27 mm 2.54 mm
. 2.54 mm 2.76 mm Thickness: 3.5mm over can, 10.8mm at SMA connector. Figure 6 JN5139-xxx-M02 Outline Drawing Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 15 18mm 7.2mm 4.05mm Jennic 40.5mm 1.27 mm 2.54 mm
. 2.54 mm 2.76 mm Thickness: 3.5mm Figure 7 JN5139-xxx-M04 Outline Drawing 16 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 A.2 Module PCB Footprint Jennic Dimensions in mm Note: All modules have the same footprint. Figure 8 Module PCB footprint RF note for M00 modules with ceramic antenna: No components, ground plane or tracks on any layer of the mother board should be placed within 20mm of the 3 free sides of the antenna. Tracks etc may be placed adjacent to the can, but should not extend past the can towards the antenna end of the module for 20mm from the antenna. Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 17 Jennic A.3 Ordering Information JN5139 - XXX - MY1Y2 Y3 Y4 Label line 1: IC ID Number Label line 2: FCC ID Number Label line 3: Part Name Label line 4: Barcode Label Label line 5: YYWWTNNNNN (see below) Identifier Description Format YY WW T NNNNN Year Week Module type Serial Number 06(example) 45(example) Shipping X T V Tape mounted samples up to 50 pieces Tape Mounted 500pieces reel (00, 03, 04 modules only) Tape Mounted 200pieces reel (01,02 modules only) Temp Range / Device Status blank -20C to +70C, qualified Module Type 00 01 02 03 04 Standard Power, Ceramic antenna Standard Power, SMA connector High Power, SMA connector Standard Power, uFl connector use for new designs High power, uFl connector use for new designs Software Variant 001 Z01 ZigBee Stack IEEE802.15.4 Stack IC: 7438A-CYO5139M0 FCC ID: TYOJN5139M0 JN51XX-XXX-XXX JENNIC YYWWTNNNNN Figure 9: Example module labelling for FCC approved modules 18 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 Jennic A.4 Tape and Reel Information:
A.4.1 Tape Orientation and dimensions All dimensions are in mm Module type:
A B W F E P0 P1 P2 T Cover Tape width (W) JN5139-xxx-M00/03 18.4 30.4 44 20.2 1.75 4.0 2.0 24.0 3.4 37.5 JN5139-xxx-M01 18.4 30.4 56 26.2 1.75 4.0 2.0 24.0 11.2 49.5 JN5139-xxx-M02 18.5 41.5 56 26.2 1.75 4.0 2.0 24.0 11.1 49.5 JN5139-xxx-M04 18.5 40.9 56 26.2 1.75 4.0 2.0 24.0 3.4 49.5 Tolerance 0.1 0.1 0.3 0.1
+0.1 0.1 0.1 0.1 0.1 0.1 A.4.2 Cover tape details Thickness (T) 0.061mm Surface resistivity (component side) 104 to 107 Ohms/sq Surface resistivity (component side) Non-conductive Backing type:
Adhesive type:
Polyester PSA Sealing:
Room ambient Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 19 Jennic A.4.3 Leader and Trailer 300 MM 300 MM A.4.4 Reel Dimensions:
Module type:
A B C N W (min) JN5139-xxx-M00/03 330 1.0 2.20.5 13 0.2 100 +0.1 44.5 0.3 JN5139-xxx-M01/02/04 330 1.0 2.20.5 13 0.2 100 +0.1 56.5 0.3 Dimensions in mm 20 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 Jennic A.5 Related Documents
[1] IEEE Std 802.15.4-2003 IEEE Standard for Information Technology Part 15.4 Wireless Medium Access Control
(MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LR-WPANs)
[2] JN-DS- JN513x Wireless Microcontroller Datasheet
[3] JN-RM-2002 802.15.4 Stack API A.6 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. WARNING!
FCC Radiation Exposure Statement:
This portable equipment with its antenna complies with FCCs RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance follow the instructions below;
1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. Avoid direct contact to the antenna, or keep it to a minimum while using this equipment. This transmitter module is authorized to be used in other devices only by OEM integrators under the following condition:
The transmitter module must not be co-located with any other antenna or transmitter. As long as the above condition is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 21 Jennic A.6.1 Antennas approved by FCC for use with JN5139 modules Brand Model Number Description Gain (dBi) Connector type 1 Aveslink Technology, Inc E-0360-AT Patch Antenna - outdoor 2 Aveslink Technology, Inc E-0260-AT Patch Antenna - outdoor 3 Aveslink Technology, Inc E-1050-AT Vertical - outdoor colinear 4 Aveslink Technology, Inc E-1040-AT Vertical - outdoor colinear 5 Aveslink Technology, Inc E-0100-AC Patch Antenna - flying lead 6 Aveslink Technology, Inc E-1030-AT Vertical - outdoor colinear 7 Aveslink Technology, Inc E-1020-AT Vertical - outdoor colinear 8 Aveslink Technology, Inc E-1710-GC 9 Aveslink Technology, Inc E-1710-GM 10 Aveslink Technology, Inc E-1511-GC Vertical - swivel Vertical - swivel Vertical - swivel 11 Aveslink Technology, Inc E-0030-AA Patch Antenna - flying lead 12 Aveslink Technology, Inc E-0030-AC Patch Antenna - flying lead 13 Aveslink Technology, Inc E-1204-AC Ceiling antenna - flying lead 14 Aveslink Technology, Inc E-1520-CA Vertical - bulkhead- flying lead 15 Aveslink Technology, Inc E-1520-GC Vertical - swivel 16 Aveslink Technology, Inc E-1450-GC Vertical-swivel mount 17 18 Nearson S152CL-L-PX-2450S Vertical - knuckle-flying lead Antenna Factor ANT-2.4-CW-RCL Vertical - knuckle antenna 19 Aveslink Technology, Inc E-0901-AA Embedded - flying lead 20 21 22 Antenna Factor ANT-2.4-CW-RCT-RP Vertical - knuckle antenna Antennova 2010B6090-01 Vertical - knuckle antenna Hyperlink Technology HG2402RD-RSF Vertical - knuckle antenna 23 Aveslink Technology, Inc E-0005-AC Vertical- flying lead 24 Aveslink Technology, Inc E-2411-GC Vertical - swivel 25 Aveslink Technology, Inc E-2410-CA Vertical - bulkhead- flying lead 26 Aveslink Technology, Inc E-2410-GC Vertical - swivel 27 Aveslink Technology, Inc E-2820-CA Vertical - bulkhead- flying lead 28 Aveslink Technology, Inc E-2820-GC Vertical - swivel 29 Aveslink Technology, Inc E-0903-AX Embedded - nickel silver strip 30 Aveslink Technology, Inc E-0904-AX Embedded - nickel silver strip 31 Embedded Antenna Design FBKR35068-RS-KR Vertical - knuckle antenna 32 33 34 Nearson S131CL-L-PX-2450S Vertical - knuckle-flying lead Laird Technologies WRR2400-IP04 Vertical - knuckle-flying lead Laird Technologies WRR2400-RPSMA Vertical - knuckle-flying lead 35 Aveslink Technology, Inc E-6170-DA Vertical - right angle 36 Laird Technologies WCR2400-SMRP Vertical - knuckle antenna 18 15 15 12 10 9 7 7 7 5 4 4 4 4 4 4 4 2.9 2.5 2.2 2.2 2.2 2 2 2 2 2 2 2 2 2 2 1.5 1.3 1 1 RP-N 1 RP-N 1 RP-N RP-N RP-SMA RP-N RP-N RP-SMA RP-TNC RP-SMA uFL RP-SMA RP-SMA uFL RP-SMA RP-SMA uFL RP-SMA uFL RP-SMA RP-SMA RP-SMA RP-SMA RP-SMA uFL RP-SMA uFL RP-SMA None None RP-SMA uFL uFL RP-SMA uFL RP-SMA These antennae or versions with alternative connectors may be used to meet European regulations, provided the gain is less than 4.4dBi. 1 These antennas may not be used with High Power Modules 22 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 Jennic This device has been designed to operate with the antennas listed above. Antennas not included in this list or having a gain greater than 18 dBi are strictly prohibited for use with this device. The required antenna impedance is 50ohms. A.6.2 High Power Module usage limitation The high power module variants are classified as mobile device pursuant with FCC 2.1091 and must not be used at a distance of < 20 cm (8) from any nearby people. IMPORTANT NOTE: In the event that these conditions can not be met (for certain configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user manual of the end product. The user manual for the end product must include the following information in a prominent location;
To comply with FCCs RF radiation exposure requirements, the antenna(s) used for this transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter. A.6.3 FCC End Product Labelling The final end product should be labelled in a visible area with the following:
Contains TX FCC ID: TYOJN5139M0, TYOJN5139M3 or TYOJN5139M4 to reflect the version of the module being used inside the product. Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 23 Jennic A.7 European R & TTE Directive 1999/5/EC Statement All modules listed in this datasheet are compliant with ETSI EN 300 328V1.7.1 (2006/05) and are subject to Notified Body Opinion RU1548/9025 Issue 2. The modules are approved for use with the antennas listed in the following table. The high power modules M02 and M04 are limited to an antenna with a gain of 2.2 dBi or less. Brand Model Number Description Gain Connector type Antenna Factor Antenna Factor ANT-2.4-CW-RCL Vertical - knuckle antenna 2.9dBi RP-SMA ANT-2.4-CW-RCT-SS Vertical - knuckle antenna Laird Technologies WCR2400-SMA Vertical - knuckle antenna Laird Technologies WRR2400-IP04 Vertical - knuckle-flying lead 1.5dBi uFL 2.2dBi 1.0dBi SMA SMA 2.0dBi 4.4dBi Embedded Antenna Design BKR2400 Vertical - knuckle antenna Antennova Nearson Nearson Titanis Vertical - knuckle antenna S131CL-L-PX-2450S Vertical - knuckle-flying lead 2.0dBi S152CL-L-PX-2450S Vertical - knuckle-flying lead 4.0dBi Aveslink Technology, Inc E-0030-AA Patch Antenna - flying lead Aveslink Technology, Inc E-0030-AB Patch Antenna - flying lead Aveslink Technology, Inc E-1204-AB Ceiling antenna - flying lead Aveslink Technology, Inc E-0005-AB Vertical- flying lead Aveslink Technology, Inc E-1450-GB Vertical-swivel mount Aveslink Technology, Inc E-1450-GC Vertical-swivel mount 4dBi 4dBi 4dBi 2dBi 4dBi 4dBi Aveslink Technology, Inc E-1520-CA Vertical - bulkhead- flying lead 4dBi Aveslink Technology, Inc E-1520-GB Vertical - swivel Aveslink Technology, Inc E-1520-GC Vertical - swivel Aveslink Technology, Inc E-2411-GB Vertical - swivel 4dBi 4dBi 2dBi Aveslink Technology, Inc E-2410-CA Vertical - bulkhead- flying lead 2dBi Aveslink Technology, Inc E-2410-GB Vertical - swivel Aveslink Technology, Inc E-2410-GC Vertical - swivel Aveslink Technology, Inc E-2410-HA Vertical - swivel -flying lead 2dBi 2dBi 2dBi Aveslink Technology, Inc E-2820-CA Vertical - bulkhead- flying lead 2dBi Aveslink Technology, Inc E-2820-GB Vertical - swivel Aveslink Technology, Inc E-2820-GC Vertical - swivel Aveslink Technology, Inc E-6170-DA Vertical - right angle 2dBi 2dBi 1dBi Aveslink Technology, Inc E-0901-AA Embedded - flying lead 2.5dBi SMA SMA uFL uFL uFL SMA SMA SMA SMA RP-SMA uFL SMA RP-SMA SMA uFL SMA RP-SMA uFL uFL SMA RP-SMA uFL uFL Hyperlink Technologies HG2402RD-RSF Vertical tilt and swivel 2.2dBi RP-SMA 24 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 A.8 Industry Canada Statement To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. These modules have been designed to operate with antennas having a maximum gain of 4.4 dBi. Antennas having a gain greater than 4.4 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. The following table shows the approved list of antennas:
Jennic Brand Model Number Description Antenna Factor ANT-2.4-CW-RCL Knuckle Antenna Antenna Factor ANT-2.4-CW-RCT-RP Knuckle Antenna Centurion Centurion Nearson Nearson Nearson WCR2400-SMRP Knuckle Antenna WRR2400-SMRP Knuckle Antenna S131CL-L-PX-2450S Knuckle Antenna 2.0 dBi S141AH-2450 Knuckle Antenna S152CL-L-PX-2450S Knuckle Antenna Hyperlink Technologies HG2402RD-RSF Knuckle Antenna Gain 2.9 dBi 2.2 dBi 1.0 dBi 1.3 dBi 2.0 dBi 4.0 dBi 2.2 dBi As long as the above condition is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc). A.8.1 Industry Canada End Product Labelling For Industry Canada purposes the following should be used. Contains Industry Canada ID IC: 7438A-CYO5139M0, IC: 7438A-CYO5139M4 or IC: 7438A-CYO5139M6 to reflect the version of the module being used inside the product. A.9 RoHS Compliance JN5139-xxx-Myy devices meet the requirements of Directive 2002/95/EC of the European Parliament and of the Council on the Restriction of Hazardous Substance (RoHS). The JN5139-xxx-M00, M03 and M04 modules are fully compliant with the Chinese RoHS requirements SJ/T11363-
2006. Further information can be found on the Jennic support website at www.jennic.com/support Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 25 Jennic A.10 Status Information The status of this Data Sheet is Production. Jennic products progress according to the following format:
Advanced The Data Sheet shows the specification of a product in planning or in development. The functionality and electrical performance specifications are target values and may be used as a guide to the final specification. Jennic reserves the right to make changes to the product specification at anytime without notice. Preliminary The Data Sheet shows the specification of a product that is in production, but is not yet fully qualified. The functionality of the product is final. The electrical performance specifications are target values and may used as a guide to the final specification. Modules are identified with an R1 suffix, for example JN5139-Z01-M00R1. Jennic reserves the right to make changes to the product specification at anytime without notice. Production This is the final Data Sheet for the product. All functional and electrical performance specifications, including minimum and maximum values are final. This Data Sheet supersedes all previous document versions. Jennic reserves the right to make changes to the product specification at anytime to improve its performance. A.11 Disclaimers The contents of this document are subject to change without notice. Jennic reserves the right to make changes, without notice, in the products, including circuits and/or software, described or contained herein in order to improve design and/or performance. Information contained in this document regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. Jennic warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with Jennics standard warranty. Testing and other quality control techniques are used to the extent Jennic deems necessary to support this warranty. Except where mandatory by government requirements, testing of all parameters of each product is not necessarily performed. Jennic assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work infringement, unless otherwise specified. Jennic products are not intended for use in life support systems, appliances or systems where malfunction of these products can reasonably be expected to result in personal injury, death or severe property or environmental damage. Jennic customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Jennic for any damages resulting from such use. All trademarks are the property of their respective owners. 26 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 Jennic A.12 Version Control Version Notes 1.0 1.1 1.2 1.3 1.4 1.5 1st Issue of Advanced Datasheet Update to correct connector positions on drawings and typo on module numbering. 000 modules now read 001. Updated to preliminary status, solder reflow profile and antenna lists added. Increased length of M02 variants Updated part numbering and addition of Industry Canada approvals Minor specification updates Updated to Production status, updated antenna information and other minor specification updates Jennic Ltd Furnival Street Sheffield S1 4QT United Kingdom Tel: +44 (0)114 281 2655 Fax: +44 (0) 114 281 2951 E-mail: info@jennic.com For the contact details of your local Jennic office or distributor, refer to the Jennic web site:
www.jennic.com Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 27
1 2 | manual | Users Manual | 678.87 KiB |
Preliminary Data Sheet JN5139-xxx-Myy IEEE802.15.4/ZigBee Module Family Overview The JN5139-xxx-Myy family is a range of surface mount modules that enable users to implement systems using IEEE802.15.4, 6LoWPAN, JenNet or ZigBee with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites. The modules use Jennics JN5139 wireless microcontroller to provide a comprehensive solution with high radio performance and all RF components included. All that is required to develop and manufacture wireless control or sensing products is to connect a power supply and peripherals such as switches, actuators and sensors, considerably simplifying product development. Three basic hardware module variants are available: JN5139-xxx-M00 with an integrated antenna, JN5139-xxx-M01/M03 with an antenna connector and JN5139-
xxx-M02/M04 with a power amplifier and LNA for extended range. Variants are available either with a ZigBee network stack (JN5139-Z01-Myy) or supporting the other stacks (JN5139-001-Myy). Module Block Diagram External Antenna Ceramic Antenna Balun M00 Option Connector Balun M01/03 Option Connector Balun PA / LNA M02/04 Option XTAL JN5139 chip RAM 96kB ROM 192kB 2.4GHz Radio O-QPSK Modem RISC CPU IEEE802.15.4 MAC Accelerator 128-bit AES Encryption Accelerator Power Management 128kB Serial Flash Memory SPI 2-wire serial Timers UARTs 12-bit ADC, comparators 11-bit DACs, temp sensor Power Benefits Microminiature module solutions Ready to use in products Minimises product development time No RF test required for systems Compliant with FCC part 15 rules, IC Canada, ETSI ETS 300-328 and Japan ARIB STD-
T66 Production volumes supplied pre-programmed with application software Applications Robust and secure low power wireless applications Wireless sensor networks, particularly IEEE802.15.4 /
ZigBee systems Home and commercial building automation Home networks Toys and gaming peripherals Telemetry and utilities Industrial systems
(e.g. AMR) Features: Module 2.4GHz IEEE802.15.4 & ZigBee compatible 2.7-3.6V operation Sleep current (with active sleep timer) 2.6A JN5139-xxx-M00/01/03 up to 1km range (ext antenna) M00: on board antenna M01: SMA connector M03: uFl connector o Receiver sensitivity 96dBm o TX power +2.5dBm o TX current 37mA o RX current 37mA o 18x30mm JN5139-xxx-M02/04 up to 4km range M02: SMA connector M04: uFl connector o Receiver sensitivity -100dBm o 19dBm TX power o TX current 125mA o RX current 45mA o 18x41mm Features: Microcontroller 16MHz 32-bit RISC CPU 96kB RAM, 192kB ROM 4-input 12-bit ADC, 2 11-bit DACs, 2 comparators, temperature sensor 2 Application timer/counters, 3 system timers 2 UARTs (one for in-system debug) SPI port with 5 selects 2-wire serial interface 21 GPIO Evaluation kits available with full, unlimited, Software Development Kit Temperature range
-20C to +70C Lead-free and RoHS compliant JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 JN5139 Single Chip Wireless Microcontroller Jennic Jennic Jennic Jennic Contents 1. Introduction 1.1. Variants 1.2. Regulatory Approvals 2. Specifications 3. Product Development 3.1. 4. Pin Configurations 4.1. Pin Assignment 4.2. Pin Descriptions Power Supplies 4.2.1 4.2.2 SPI Memory Connections 5. Electrical Characteristics 5.1. Maximum Ratings 5.2. Reflow Profile 5.3. Operating Conditions Appendix A Additional Information A.1 Outline Drawing A.2 Module PCB Footprint A.3 Ordering Information A.4 Tape and Reel Information:
A.4.1 Tape Orientation and dimensions A.4.2 Cover tape details A.4.3 Leader and Trailer A.4.4 Reel Dimensions:
A.5 Related Documents A.6 Federal Communication Commission Interference Statement A.6.1 Antennas approved by FCC for use with JN5139 modules A.6.2 High Power Module usage limitation A.6.3 FCC End Product Labelling A.7 European R & TTE Directive 1999/5/EC Statement A.8 Industry Canada Statement A.8.1 Industry Canada End Product Labelling A.9 RoHS Compliance A.10 Status Information A.11 Disclaimers A.12 Version Control 3 3 3 4 5 5 6 7 8 8 8 9 9 9 10 11 11 16 17 18 18 18 19 19 20 20 21 22 22 23 24 24 24 25 25 26 ii JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 Jennic Jennic Jennic Jennic 1. Introduction The JN5139-xxx-Myy module family provides designers with a ready made component which allows IEEE802.15.4 [1]
wireless applications, using Jennics JenNet networking protocol or ZigBee, to be quickly and easily included in product designs. The modules integrate all of the RF components required, removing the need to perform expensive RF design and test. Products can be designed by simply connecting sensors and switches to the module IO pins. The modules use Jennics single chip IEEE802.15.4 Wireless Microcontroller, allowing designers to make use of the extensive chip development support material. Hence, this range of modules allows designers to bring wireless applications to market in the minimum time with significantly reduced development effort and cost. Three module hardware variants are available: JN5139-xxx-M00 (standard module with on board ceramic antenna), JN5139-xxx-M01 (standard module with SMA connector for use with external antennae recommended for evaluation use) and JN5139-xxx-M02 (high RF power, improved sensitivity module for evaluation of extended range applications). For volume production applications, uFL connector variants are provided (-M03 standard power and M04 high power). These devices, together with the M00 variants have FCC modular approvals. Each of these modules can be supplied with a range of protocol stacks, including JenNet for most tree and linear networks, IEEE802.15.4 protocol for point-to-point and star applications and a ZigBee mesh networking stack. The variants available are described below. 1.1. Variants Variant Description FCCID JN5139-001-M00 IEEE802.15.4 stack, ceramic antenna TYOJN5139M0 JN5139-Z01-M00 JN5139-001-M01 ZigBee stack, ceramic antenna IEEE802.15.4 stack, SMA connector - for evaluation ZigBee stack, SMA connector for evaluation JN5139-Z01-M01 JN5139-001-M02 High Power, IEEE802.15.4 stack, SMA JN5139-Z01-M02 High Power, ZigBee stack, SMA connector connector for evaluation JN5139-001-M03 for evaluation IEEE802.15.4 stack, uFl connector JN5139-Z01-M03 JN5139-001-M04 High Power, IEEE802.15.4 stack, uFl ZigBee stack, uFl connector connector TYOJN5139M0 N/A N/A N/A N/A TYOJN5139M3 TYOJN5139M3 TYOJN5139M4 JN5139-Z01-M04 High Power, ZigBee stack, uFl connector TYOJN5139M4 Industry Canada ID IC: 7438A-CYO5139M0 IC: 7438A-CYO5139M0 IC: 7438A-CYO5139M6 IC: 7438A-CYO5139M6 IC: 7438A-CYO5139M4 IC: 7438A-CYO5139M4 IC: 7438A-CYO5139M6 IC: 7438A-CYO5139M6 IC: 7438A-CYO5139M4 IC: 7438A-CYO5139M4 1.2. Regulatory Approvals All module types have been tested against the requirements of European standard ETS 300 328 v1.7.1 and a Notified Body statement of opinion for this standard is available on request. The High Power modules with M02 or M04 suffix are approved for use in Europe with reduced output power: +10dBm EIRP is the maximum permitted in Europe. They must not be used with PHY_PIB_ATTR_TX_POWER set above 50 See [3] JN-RM-2002 802.15.4 Stack API. Additionally, modules with M00, M03 and M04 suffixes have received FCC Modular Approvals, in compliance with CFR 47 FCC part 15 regulations and in accordance to FCC Public notice DA00-1407. The modules are approved for use with a number of antennase, refer to section A.6.1 for details. See Appendix A.6 for details on the conditions applying to this modular approval. The modular approvals notice and test reports are available on request. The high power module variant is classified as mobile device pursuant with FCC 2.1091 and must not be used at a distance of less than 20 cm (8) from any person. In addition, all modules have Industry Canada RSS 210 Issue 7 (June 2007) certification. Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 3 Jennic Jennic Jennic Jennic 2. Specifications Most specification parameters for the modules are specified in the chip datasheet - JN-DS- JN513x Wireless Microcontroller Datasheet, [2]. Where there are differences, the parameters are defined here. Typical DC Characteristics Notes Centre frequency accuracy
+/-25ppm
+/-25ppm Typical RF Characteristics Notes VDD=3.0V @ +25C Deep sleep current Sleep current Radio transmit current Radio receive current Receive sensitivity Maximum Transmit power Maximum Transmit power [Boost Mode]
Transmit power at 3.6V Maximum input signal RSSI range RF Port impedance SMA/uFl connector VSWR (max) Master SPI port Slave SPI port Two UARTs Two-wire serial I/F (compatible with SMbus & I2C) Two programmable Timer/Counters with capture/compare facility, Tick timer Two programmable Sleep Timers Digital IO lines (multiplexed with UARTs, timers and SPI selects) Four channel Analogue-to-Digital converter Two channel Digital-to-Analogue converter Two programmable analogue comparators Internal temperature sensor and battery monitor JN5139-xxx-
M00/01/03 JN5139-xxx-
M02/04 1.3uA 2.6uA 37mA 37mA 1.3uA 2.6uA 125mA 45mA With active sleep timer CPU in doze, radio transmitting CPU in doze, radio receiving Additional +/-15ppm allowance for temperature and ageing
-96dBm
-102dBm Nominal for 1% PER, as per 802.15.4 section 6.5.3.3 (Note 1)
+1dBm
+2.5dBm 17.5dBm Nominal (Note 1) N/A
(Note 1) 19dBm With Vdd=3.6V
+10dBm
+10dBm For 1% PER, measured as sensitivity
-95 to -10 dBm 50 ohm 2:1
-105 to -20 dBm 50 ohm 2.4 - 2.5GHz 2:1 2.4 - 2.5GHz 21 19 250kHz - 8MHz 16550 compatible Up to 400kHz 16MHz clock 32kHz clock 12-bit, up to 100ks/s 11-bit, up to 100ks/s Ultra low power mode for sleep Peripherals Notes 5 selects 3 selects 250kHz - 16MHz The performance of all peripherals is defined in the JN-DS- JN513x Wireless Microcontroller Datasheet [2]
Note 1: Sensitivity is defined for conducted measurements on connectorised modules. Modules with an integrated antenna have approximately 4 dB less e.i.r.p and reciprocal receive sensitivity. 4 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 Jennic Jennic Jennic Jennic 3. Product Development Jennic supplies all the development tools and networking stacks needed to enable end product development to occur quickly and efficiently. These are all freely available from Jennics support website: http://www.jennic.com/support/ . A range of evaluation/developer kits is also available, allowing products to be quickly breadboarded. Efficient development of software applications is enabled by the provision of a complete, unlimited, software developer kit. Together with the available libraries for the JenNet networking stack, the IEEE802.15.4 MAC and the ZigBee network stack, this package provides everything required to develop application code and to trial it with hardware representative of the final module. The modules can be user programmed both in development and in production using software supplied by Jennic. They can also be supplied ready loaded with customer defined software if required. Access to the on-chip peripherals, MAC and network stack software is provided through specific APIs. This information is available on the Jennic support website, together with many example applications, user guides, reference manuals and application notes. 3.1. JN5139 Single Chip Wireless Microcontroller The JN5139-xxx-Myy series is constructed around the JN5139 single chip wireless microcontroller, which includes the radio system, a 32-bit RISC CPU, ROM and RAM memory and a range of analogue and digital peripherals. The chip is described fully in JN-DS- JN513x Wireless Microcontroller Datasheet [2]. The module also includes a 1Mbit serial flash memory which holds the application code that is loaded into the JN5139 during the boot sequence. Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 5 Jennic Jennic Jennic Jennic 4. Pin Configurations a J1 n n e t n A ADC4 DAC1 DAC2 COMP2+
COMP2-
SPICLK SPIMISO SPIMOSI SPISSZ DIO0/SPISEL1 DIO1/SPISEL2 DIO2/SPISEL3 SPISSM SPISWP DIO3/SPISEL4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 ADC3 ADC2 ADC1 COMP1+
COMP1-
DIO20/RXD1 DIO19/TXD1 DIO18/RTS1 DIO17/CTS1 DIO16 DIO15/SIF_D DIO14/SIF_CLK RESETN DIO13/TIM1_OUT DIO12/TIM1_CAP D D V D N G A S S V 0 S T C
4 O D I 0 S T R
5 O D I 0 D X T
6 O D I 0 D X R
7 O D I I T G 0 M T
8 O D I P A C _ 0 M T
9 O D I I T U O _ 0 M T
0 1 O D I I I T G 1 M T
1 1 O D I Figure 1: Pin Configuration (top view) Note that the same basic pin configuration applies for all module designs. However, DIO3/SPISEL4 and DIO2/SPISEL3 are not available on the high power modules. 6 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 4.1. Pin Assignment Function Pin Signal Jennic Jennic Jennic Jennic Alternative Function 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 ADC4 DAC1 DAC2 COMP2+
COMP2-
Analogue to Digital input Digital to Analogue output Digital to Analogue output Comparator 2 inputs SPICLK SPI master clock out SPIMISO SPI Master In/Slave Out SPIMOSI SPI Master Out/Slave In SPISSZ SPI select from module - SS0 (output) SPISEL1 SPI Slave Select1 (output) General Purpose Digital I/O DIO0 SPISEL2 SPI Slave Select2 (output) General Purpose Digital I/O DIO1 SPISEL3*
SPI Slave Select3 (output) General Purpose Digital I/O DIO2 *
SPISSM SPI select to FLASH (input) SPISWP FLASH write protect (input) SPISEL4*
SPI Slave Select4 (output) General Purpose Digital I/O DIO3*
CTS0 RTS0 TXD0 RXD0 UART0 Clear To Send (input) General Purpose Digital I/O DIO4 UART0 Request To Send (output) General Purpose Digital I/O DIO5 UART0 Transmit Data (output) General Purpose Digital I/O DIO6 UART0 Receive Data (input) General Purpose Digital I/O DIO7 TIM0GT Timer0 clock/gate (input) General Purpose Digital I/O DIO8 TIM0_CAP Timer0 capture (input) General Purpose Digital I/O DIO9 TIM0_OUT Timer0 PWM (output) General Purpose Digital I/O DIO10 TIM1GT Timer1 clock/gate (input) General Purpose Digital I/O DIO11 VDD GND VSSA 3V power Digital ground Analogue ground TIM1_CAP Timer1 capture (input) General Purpose Digital I/O DIO12 TIM1_OUT Timer1 PWM (output) General Purpose Digital I/O DIO13 RESETN Active low reset SIF_CLK Serial Interface clock / Intelligent peripheral clock General Purpose Digital I/O DIO14 Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 7 Jennic Jennic Jennic Jennic Pin Signal Function Alternative Function 31 32 33 SIF_D Serial Interface data / Intelligent peripheral data out (output) General Purpose Digital I/O DIO15 DIO 16 Intelligent peripheral device data in (input) General Purpose Digital I/O CTS1 UART1 Clear To Send (input) / Intelligent peripheral device select (input) General Purpose Digital I/O DIO17 34a RTS1 UART1 Request To Send (output) / Intelligent peripheral interrupt (output) General Purpose Digital I/O DIO18 35 36 37 38 39 40 41 TXD1 RXD1 COMP1-
COMP1+
ADC1 ADC2 ADC3 UART1 Transmit Data (output) General Purpose Digital I/O DIO19 UART1 Receive Data (input) General Purpose Digital I/O DIO20 Comparator 1 inputs Analogue to Digital input Analogue to Digital input Analogue to Digital input
*: These two pins are not connected for High power modules 4.2. Pin Descriptions All pins behave as described in the JN-DS- JN513x Wireless Microcontroller Datasheet [2], with the exception of the following:
4.2.1 Power Supplies A single power supply pin, VDD is provided. Separate analogue (VSSA) and digital (GND) grounds are provided. These should be connected together at the module pins. 4.2.2 SPI Memory Connections SPISWP is a write protect pin for the serial flash memory. This should be held low to inhibit writes to the flash device. SPISSZ is connected to SPI Slave Select 0 on the JN5139. SPISSM is connected to the Slave Select pin on the memory. This configuration allows the flash memory device to be programmed using an external SPI programmer if required. For programming in this mode, the JN5139 should be held in reset by taking RESETN low. The memory can also be programmed over the UART by using the flash programmer software provided by Jennic. This is available as part of the Software Developer kit and libraries available from Jennics support website www.jennic.com/support. To enter this programming mode, SPIMISO (pin 7) should be held low whilst the chip is reset. Once programming has finished, the chip should be reset, when it will execute the new code downloaded. For normal operation of the module and programming over the UART, SPISSZ should be connected to SPISSM. 8 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 5. Electrical Characteristics In most cases, the Electrical Characteristics are the same for both module and chip. They are described in detail in the chip datasheet. Where there are differences, they are detailed below. Jennic Jennic Jennic Jennic 5.1. Maximum Ratings Exceeding these conditions will result in damage to the device. Parameter Device supply voltage VDD Voltage on analogue pins: ADC1-4, DAC1-2, COMP1-, COMP1+, COMP2-, COMP2+, DIO9, DIO10, SPISSM, SPISWP, SPICLK, SPIMOSI, SPIMISO, Voltage on 5v tolerant digital pins: SPISSZ, DIO0-
DIO8, DIO11-DIO20, RESETN Storage temperature Reflow soldering temperature according to IPC/JEDEC J-STD-020C Min
-0.3V
-0.3V
-0.3V
-40C Max 3.6V VDD + 0.3V Lower of (VDD + 2V) and 5.5V 150C 260C This device is sensitive to ESD and should only be handled using ESD precautions. 5.2. Reflow Profile For reflow soldering, it is recommended to follow the reflow profile in Figure 2 as a guide, as well as the paste manufacturers guidelines on peak flow temperature, soak times, time above liquidus and ramp rates. Temperature 25~160 C 160~190 C
> 220 C 230~Pk. Pk. Temp
(235C) Target Time (s) 90~130 30~60 20~50 10~15 160~270 Figure 2: Recommended solder reflow profile Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 9 Jennic Jennic Jennic Jennic 5.3. Operating Conditions Supply VDD Ambient temperature range Min 2.7V
-20C Max 3.6V 70C 10 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 Appendix A Additional Information A.1 Outline Drawing 18mm J1 a n n e t n A 30mm Jennic Jennic Jennic Jennic 1.27 mm 2.54 mm 2.54 mm Thickness: 3.5mm 2.76 mm Figure 3 JN5139-xxx-M00 Outline Drawing Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 11 Jennic Jennic Jennic Jennic 30mm 18mm 9.74mm 4.59 mm 1.27 mm 2.54 mm 2.54 mm 2.76 mm Thickness: 3.5mm over can, 10.8mm at SMA connector Figure 4 JN5139-xxx-M01 Outline Drawing 12 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 Jennic Jennic Jennic Jennic 18mm 9.76mm 6.58 mm 30mm 1.27 mm 2.54 mm 2.54 mm 2.76 mm Figure 5 JN5139-xxx-M03 Outline Drawing Thickness: 3.5mm Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 13 18mm 7.2mm 4.32 mm Jennic Jennic Jennic Jennic 41mm 1.27 mm 2.54 mm 2.76 mm
. 2.54 mm Thickness: 3.5mm over can, 10.8mm at SMA connector. Figure 6 JN5139-xxx-M02 Outline Drawing 14 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 Jennic Jennic Jennic Jennic 18mm 7.2mm 4.05mm 40.5mm 1.27 mm 2.54 mm 2.76 mm Figure 7 JN5139-xxx-M04 Outline Drawing
. 2.54 mm Thickness: 3.5mm Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 15 Jennic Jennic Jennic Jennic A.2 Module PCB Footprint Dimensions in mm Note: All modules have the same footprint. Figure 8 Module PCB footprint RF note for M00 modules with ceramic antenna: No components, ground plane or tracks on any layer of the mother board should be placed within 20mm of the 3 free sides of the antenna. Tracks etc may be placed adjacent to the can, but should not extend past the can towards the antenna end of the module for 20mm from the antenna. 16 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 A.3 Ordering Information JN5139 - XXX - MY1Y2 Y3 Y4 Jennic Jennic Jennic Jennic Shipping X T V Tape mounted samples up to 50 pieces Tape Mounted 500pieces reel (00, 03, 04 modules only) Tape Mounted 200pieces reel (01,02 modules only) Temp Range / Device Status blank -20 C to +70 C, qualified Module Type 00 01 02 03 04 Standard Power, Ceramic antenna Standard Power, SMA connector High Power, SMA connector Standard Power, uFl connector use for new designs High power, uFl connector use for new designs Software Variant 001 Z01 ZigBee Stack IEEE802.15.4 Stack Label line 1: IC ID Number Label line 2: FCC ID Number Label line 3: Part Name Label line 4: Barcode Label Label line 5: YYWWTNNNNN (see below) Identifier Description Format YY WW T NNNNN Year Week Module type Serial Number 06(example) 45(example) IC: 7438A-CYO5139M0 FCC ID: TYOJN5139M0 JN51XX-XXX-XXX JENNIC YYWWTNNNNN Figure 9: Example module labelling for FCC approved modules Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 17 Jennic Jennic Jennic Jennic A.4 Tape and Reel Information:
A.4.1 Tape Orientation and dimensions All dimensions are in mm Module type:
A B W F E P0 P1 P2 T Cover Tape width (W) JN5139-xxx-M00/03 18.4 30.4 44 20.2 1.75 4.0 JN5139-xxx-M01 18.4 30.4 56 26.2 1.75 4.0 JN5139-xxx-M02 18.5 41.5 56 26.2 1.75 4.0 JN5139-xxx-M04 18.5 40.9 56 26.2 1.75 4.0 2.0 2.0 2.0 2.0 24.0 3.4 37.5 24.0 11.2 49.5 24.0 11.1 49.5 24.0 3.4 49.5 Tolerance 0.1 0.1 0.3 0.1
+0.1 0.1 0.1 0.1 0.1 0.1 A.4.2 Cover tape details Thickness (T) 0.061mm Surface resistivity (component side) 104 to 107 Ohms/sq Surface resistivity (component side) Non-conductive Backing type:
Adhesive type:
Sealing:
Polyester PSA Room ambient 18 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 A.4.3 Leader and Trailer Jennic Jennic Jennic Jennic 300 MM A.4.4 Reel Dimensions:
300 MM Module type:
A B JN5139-xxx-M00/03 330 1.0 2.20.5 JN5139-xxx-M01/02/04 330 1.0 2.20.5 C 13 0.2 13 0.2 N 100 +0.1 100 +0.1 W (min) 44.5 0.3 56.5 0.3 Dimensions in mm Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 19 Jennic Jennic Jennic Jennic A.5 Related Documents
[1] IEEE Std 802.15.4-2003 IEEE Standard for Information Technology Part 15.4 Wireless Medium Access Control
(MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LR-WPANs)
[2] JN-DS- JN513x Wireless Microcontroller Datasheet
[3] JN-RM-2002 802.15.4 Stack API A.6 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. WARNING!
FCC Radiation Exposure Statement:
This portable equipment with its antenna complies with FCCs RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance follow the instructions below;
1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. Avoid direct contact to the antenna, or keep it to a minimum while using this equipment. This transmitter module is authorized to be used in other devices only by OEM integrators under the following condition:
The transmitter module must not be co-located with any other antenna or transmitter. As long as the above condition is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). 20 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 A.6.1 Antennas approved by FCC for use with JN5139 modules Brand Model Number Description Gain (dBi) Connector type Jennic Jennic Jennic Jennic Nearson Antenna Factor E-0360-AT E-0260-AT E-1050-AT E-1040-AT E-0100-AC E-1030-AT E-1020-AT E-1710-GC E-1710-GM E-1511-GC E-0030-AA E-0030-AC E-1204-AC E-1520-CA E-1520-GC E-1450-GC 1 Aveslink Technology, Inc 2 Aveslink Technology, Inc 3 Aveslink Technology, Inc 4 Aveslink Technology, Inc 5 Aveslink Technology, Inc 6 Aveslink Technology, Inc 7 Aveslink Technology, Inc 8 Aveslink Technology, Inc 9 Aveslink Technology, Inc 10 Aveslink Technology, Inc 11 Aveslink Technology, Inc 12 Aveslink Technology, Inc 13 Aveslink Technology, Inc 14 Aveslink Technology, Inc 15 Aveslink Technology, Inc 16 Aveslink Technology, Inc 17 18 19 Aveslink Technology, Inc 20 21 22 23 Aveslink Technology, Inc 24 Aveslink Technology, Inc 25 Aveslink Technology, Inc 26 Aveslink Technology, Inc 27 Aveslink Technology, Inc 28 Aveslink Technology, Inc 29 Aveslink Technology, Inc 30 Aveslink Technology, Inc 31 Embedded Antenna Design FBKR35068-RS-KR 32 S131CL-L-PX-2450S 33 34 35 Aveslink Technology, Inc 36 E-0005-AC E-2411-GC E-2410-CA E-2410-GC E-2820-CA E-2820-GC E-0903-AX E-0904-AX Laird Technologies Laird Technologies 2010B6090-01 HG2402RD-RSF Hyperlink Technology S152CL-L-PX-2450S WRR2400-RPSMA Laird Technologies ANT-2.4-CW-RCL WCR2400-SMRP WRR2400-IP04 Antenna Factor E-6170-DA E-0901-AA Antennova Nearson ANT-2.4-CW-RCT-RP Patch Antenna - outdoor Patch Antenna - outdoor Vertical - outdoor colinear Vertical - outdoor colinear Patch Antenna - flying lead Vertical - outdoor colinear Vertical - outdoor colinear Vertical - swivel Vertical - swivel Vertical - swivel Patch Antenna - flying lead Patch Antenna - flying lead Ceiling antenna - flying lead Vertical - bulkhead- flying lead Vertical - swivel Vertical-swivel mount Vertical - knuckle-flying lead Vertical - knuckle antenna Embedded - flying lead Vertical - knuckle antenna Vertical - knuckle antenna Vertical - knuckle antenna Vertical- flying lead Vertical - swivel Vertical - bulkhead- flying lead Vertical - swivel Vertical - bulkhead- flying lead Vertical - swivel Embedded - nickel silver strip Embedded - nickel silver strip Vertical - knuckle antenna Vertical - knuckle-flying lead Vertical - knuckle-flying lead Vertical - knuckle-flying lead Vertical - right angle Vertical - knuckle antenna 18 15 15 12 10 9 7 7 7 5 4 4 4 4 4 4 4 2.9 2.5 2.2 2.2 2.2 2 2 2 2 2 2 2 2 2 2 1.5 1.3 1 1 RP-N 1 RP-N RP-N RP-N RP-SMA RP-N RP-N RP-SMA RP-TNC RP-SMA uFL RP-SMA RP-SMA uFL RP-SMA RP-SMA uFL RP-SMA uFL RP-SMA RP-SMA RP-SMA RP-SMA RP-SMA uFL RP-SMA uFL RP-SMA None None RP-SMA uFL uFL RP-SMA uFL RP-SMA These antennae or versions with alternative connectors may be used to meet European regulations, provided the gain is less than 4.4dBi. 1 This antenna may not be used with High Power Modules Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 21 Jennic Jennic Jennic Jennic This device has been designed to operate with the antennas listed above. Antennas not included in this list or having a gain greater than 18 dBi are strictly prohibited for use with this device. The required antenna impedance is 50ohms. A.6.2 High Power Module usage limitation The high power module variants are classified as mobile device pursuant with FCC 2.1091 and must not be used at a distance of < 20 cm (8) from any nearby people. IMPORTANT NOTE: In the event that these conditions can not be met (for certain configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user manual of the end product. The user manual for the end product must include the following information in a prominent location;
To comply with FCCs RF radiation exposure requirements, the antenna(s) used for this transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter. A.6.3 FCC End Product Labelling The final end product should be labelled in a visible area with the following:
Contains TX FCC ID: TYOJN5139M0, TYOJN5139M3 or TYOJN5139M4 to reflect the version of the module being used inside the product. 22 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 A.7 European R & TTE Directive 1999/5/EC Statement All modules listed in this datasheet are compliant with ETSI EN 300 328V1.7.1 (2006/05) and are subject to Notified Body Opinion RU1548/9025 Issue 2. The modules are approved for use with the antennas listed in the following table. The high power modules M02 and M04 are limited to an antenna with a gain of 2.2 dBi or less. Jennic Jennic Jennic Jennic Gain Connector type Brand Description Model Number ANT-2.4-CW-RCL Vertical - knuckle antenna ANT-2.4-CW-RCT-SS Vertical - knuckle antenna Vertical - knuckle antenna WCR2400-SMA Vertical - knuckle-flying lead WRR2400-IP04 Vertical - knuckle antenna Vertical - knuckle antenna Antenna Factor Antenna Factor Laird Technologies Laird Technologies Embedded Antenna Design BKR2400 Antennova Nearson Nearson Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Aveslink Technology, Inc Hyperlink Technologies 2.9dBi 2.2dBi 1.0dBi 1.5dBi 2.0dBi 4.4dBi Titanis 2.0dBi S131CL-L-PX-2450S Vertical - knuckle-flying lead 4.0dBi S152CL-L-PX-2450S Vertical - knuckle-flying lead 4dBi E-0030-AA Patch Antenna - flying lead 4dBi Patch Antenna - flying lead E-0030-AB 4dBi Ceiling antenna - flying lead E-1204-AB 2dBi E-0005-AB Vertical- flying lead 4dBi Vertical-swivel mount E-1450-GB Vertical-swivel mount E-1450-GC 4dBi Vertical - bulkhead- flying lead 4dBi E-1520-CA E-1520-GB Vertical - swivel 4dBi 4dBi Vertical - swivel E-1520-GC Vertical - swivel E-2411-GB 2dBi E-2410-CA Vertical - bulkhead- flying lead 2dBi 2dBi Vertical - swivel E-2410-GB 2dBi Vertical - swivel E-2410-GC Vertical - swivel -flying lead E-2410-HA 2dBi E-2820-CA Vertical - bulkhead- flying lead 2dBi 2dBi Vertical - swivel E-2820-GB 2dBi Vertical - swivel E-2820-GC 1dBi Vertical - right angle E-6170-DA E-0901-AA Embedded - flying lead 2.5dBi 2.2dBi Vertical tilt and swivel HG2402RD-RSF RP-SMA SMA SMA uFL SMA SMA uFL uFL uFL SMA SMA SMA SMA RP-SMA uFL SMA RP-SMA SMA uFL SMA RP-SMA uFL uFL SMA RP-SMA uFL uFL RP-SMA Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 23 Jennic Jennic Jennic Jennic A.8 Industry Canada Statement To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. These modules have been designed to operate with antennas having a maximum gain of 4.4 dBi. Antennas having a gain greater than 4.4 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. The following table shows the approved list of antennas:
Brand Antenna Factor Antenna Factor Centurion Centurion Nearson Nearson Nearson Model Number Description ANT-2.4-CW-RCL ANT-2.4-CW-RCT-RP WCR2400-SMRP WRR2400-SMRP S131CL-L-PX-2450S S141AH-2450 S152CL-L-PX-2450S Knuckle Antenna Knuckle Antenna Knuckle Antenna Knuckle Antenna Knuckle Antenna Knuckle Antenna Knuckle Antenna Knuckle Antenna Gain 2.9 dBi 2.2 dBi 1.0 dBi 1.3 dBi 2.0 dBi 2.0 dBi 4.0 dBi 2.2 dBi Hyperlink Technologies HG2402RD-RSF As long as the above condition is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc). A.8.1 Industry Canada End Product Labelling For Industry Canada purposes the following should be used. Contains Industry Canada ID IC: 7438A-CYO5139M0, IC: 7438A-CYO5139M4 or IC: 7438A-CYO5139M6 to reflect the version of the module being used inside the product. A.9 RoHS Compliance JN5139-xxx-Myy devices meet the requirements of Directive 2002/95/EC of the European Parliament and of the Council on the Restriction of Hazardous Substance (RoHS). The JN5139-xxx-M00, M03 and M04 modules are fully compliant with the Chinese RoHS requirements SJ/T11363-
2006. Further information can be found on the Jennic support website at www.jennic.com/support 24 JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009 Jennic Jennic Jennic Jennic A.10 Status Information The status of this Data Sheet is Production. Jennic products progress according to the following format:
Advanced The Data Sheet shows the specification of a product in planning or in development. The functionality and electrical performance specifications are target values and may be used as a guide to the final specification. Jennic reserves the right to make changes to the product specification at anytime without notice. Preliminary The Data Sheet shows the specification of a product that is in production, but is not yet fully qualified. The functionality of the product is final. The electrical performance specifications are target values and may used as a guide to the final specification. Modules are identified with an R1 suffix, for example JN5139-Z01-M00R1. Jennic reserves the right to make changes to the product specification at anytime without notice. Production This is the final Data Sheet for the product. All functional and electrical performance specifications, including minimum and maximum values are final. This Data Sheet supersedes all previous document versions. Jennic reserves the right to make changes to the product specification at anytime to improve its performance. A.11 Disclaimers The contents of this document are subject to change without notice. Jennic reserves the right to make changes, without notice, in the products, including circuits and/or software, described or contained herein in order to improve design and/or performance. Information contained in this document regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. Jennic warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with Jennics standard warranty. Testing and other quality control techniques are used to the extent Jennic deems necessary to support this warranty. Except where mandatory by government requirements, testing of all parameters of each product is not necessarily performed. Jennic assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work infringement, unless otherwise specified. Jennic products are not intended for use in life support systems, appliances or systems where malfunction of these products can reasonably be expected to result in personal injury, death or severe property or environmental damage. Jennic customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Jennic for any damages resulting from such use. All trademarks are the property of their respective owners. Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 25 Jennic Jennic Jennic Jennic A.12 Version Control Version Notes 1.0 1.1 1.2 1.3 1.4 1.5 26 1st Issue of Advanced Datasheet Update to correct connector positions on drawings and typo on module numbering. 000 modules now read 001. Updated to preliminary status, solder reflow profile and antenna lists added. Increased length of M02 variants Updated part numbering and addition of Industry Canada approvals Minor specification updates Updated to Production status, updated antenna information and other minor specification updates Jennic Ltd Furnival Street Sheffield S1 4QT United Kingdom Tel: +44 (0)114 281 2655 Fax: +44 (0) 114 281 2951 E-mail: info@jennic.com www.jennic.com For the contact details of your local Jennic office or distributor, refer to the Jennic web site:
JN-DS-JN5139-xxx-Myy 1v5 Jennic 2009
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2009-03-26 | 2400 ~ 2483.5 | DTS - Digital Transmission System | Class II permissive change or modification of presently authorized equipment |
2 | 2007-03-28 | 2400 ~ 2483.5 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2009-03-26
|
||||
1 2 |
2007-03-28
|
|||||
1 2 | Applicant's complete, legal business name |
NXP Laboratories UK Ltd
|
||||
1 2 | FCC Registration Number (FRN) |
0014596860
|
||||
1 2 | Physical Address |
Furnival St
|
||||
1 2 |
Sheffield, N/A S1 4QT
|
|||||
1 2 |
United Kingdom
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
p******@tracglobal.com
|
||||
1 2 |
m******@trlcompliance.com
|
|||||
1 2 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
TYO
|
||||
1 2 | Equipment Product Code |
JN5139M0
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
C****** F******
|
||||
1 2 | Telephone Number |
+44 1********
|
||||
1 2 | Fax Number |
+44 1********
|
||||
1 2 |
c******@nxp.com
|
|||||
app s | Technical Contact | |||||
1 2 | Firm Name |
Jennic Ltd
|
||||
1 2 | Name |
C**** F****
|
||||
1 2 | Physical Address |
Furnival Street
|
||||
1 2 |
S1 4QT
|
|||||
1 2 |
United Kingdom
|
|||||
1 2 | Telephone Number |
+44 1********
|
||||
1 2 | Fax Number |
+44 1********
|
||||
1 2 |
c******@jennic.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | DTS - Digital Transmission System | ||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | IEEE 802.15.4 Wireless Microcontroller | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Single Modular Approval | ||||
1 2 | Purpose / Application is for | Class II permissive change or modification of presently authorized equipment | ||||
1 2 | Original Equipment | |||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Output power listed is conducted. Modular Approval for mobile RF Exposure conditions, the antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Approval is limited to OEM installation only. OEM integrators must be provided with antenna installation instructions. OEM integrators and end-users must be provided with transmitter operating conditions for satisfying RF exposure compliance. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no instructions to remove or install the device. This Grant covers the following Module Variants: JN5139-T01-C1, JN5139-J1-C1, JN5139-001-M and JN5139-Z01-M | ||||
1 2 | Output power is conducted. Modular Approval. | |||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
R.N. Electronics Ltd.
|
||||
1 2 | Name |
R****** R******
|
||||
1 2 | Telephone Number |
44-12********
|
||||
1 2 | Fax Number |
44-12********
|
||||
1 2 |
r******@RNelectronics.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2400.00000000 | 2483.50000000 | 0.0018000 | ||||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15C | 2400.00000000 | 2483.50000000 | 0.0018000 | JN5139 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC