Model V680S-HMD64-ETN RFID System Reader/Writer INSTRUCTION SHEET Thank you for selecting OMRON product. This sheet pri-
marily describes precautions required in installing and operating the product. Before operating the product, read the sheet thoroughly to acquire sufficient knowledge of the product. For your con-
venience, keep the sheet at your disposal. TRACEABILITY INFORMATION:
Representative in EU:
Omron Europe B.V. Wegalaan 67-69 2132 JD Hoofddorp, The Netherlands Manufacturer:
Omron Corporation, Shiokoji Horikawa, Shimogyo-ku, Kyoto 600-8530 JAPAN Ayabe Factory 3-2 Narutani, Nakayama-cho, Ayabe-shi, Kyoto 623-0105 JAPAN OMRON Corporation All Rights Reserved. 2013 SAFETY PRECATIONS Meaning of Signal Words WARNING InIndicates a potentially hazardous situation which, if not avoided, will result in minor or moderateinjury, or may result in serious injury or death. Additionally, there may be signicant property damage. Meaning of Alert Symbols Indicates general prohibitions for which there is no specic symbol. Warning WARNING These Products are not designed to be used either directly or indirectly in applications that detect human presence for the purpose of maintaining safety. Do not use these Products as a sensing means for protecting human lives. PRECAUTIONS FOR SAFE USE Observe the following precautions to ensure safe usage of the product. 1. Installation and Storage Environment Do not install the Products near any equipment that generates a large amount of heat (such as heaters,transformers, and large-capacity resistors). If many Reader/Writer are mounted near each other, communications performance may decrease due to mutual interference. Refer to Reference Data in Section 7 Appendices of Users Manual and check to make sure there is no mutual interference. 2. Installation and Removing Do not use the AC power supply. Do not perform wiring incorrectly. Doing so may result in rupture or Ground to 100 or less through a host device (Ethernet switch damage from burning. or PLCs etc). Use an exclusive cable as model V680S-A40, V680S-A41, or V680S-A42. 3. Using Do not bend the cable past a bending radius of 40 mm. The cable may be disconnected. If you find an abnormal operation of the product, immediately stop its operation and turn OFF the power supply. Consult with an OMRON representative. Do not clean the Products with paint thinner, benzene, acetone, or kerosene. 4. Cleaning 5. Disposing Dispose of the Products as industrial waste. PRECAUTIONS FOR CORRECT USE 1. Installation and Storage Environment Do not use or store the Product in the following locations. Locations subject to corrosive gases, dust, dirt, metal powder, or salt. Locations where ambient temperature or ambient humidity range is over the specified. in dew condensation. Locations subject to extreme temperature changes that may result Locations where the product would be directly subjected to vibration or shock exceeding specifications. 2. Installation The Products communicate with RF Tags using the 13.56-MHz frequency. Any transceivers, motors, inverters, or switching power supplies generate noise that can affect communications with the Tags and cause errors. If such devices are located near the Tags, always test operation in advance to confirm whether the system may be affected. When you use the Reader/Writer in RUN mode, the control signal should be connected to the +24 V of the power supply the Reader/Writer will operate in safe mode when the control signal is connected to 0 V of the power supply. Make sure the power supplied by the DC power supply unit is within the rated power supply voltage (24 VDC +10%/15%) before using the Product. Securely tighten the screws to a torque of 1.2Nm when mounting the Use a tightening torque of 0.3 to 0.49Nm when mounting the cable connector. reader/writer. 3. Prohibitions 4. Maintenance Do not drop the Products. Do not pull on the cables with excessive strength. Do not attempt to disassemble, repair, or modify the Procuct. The reader/writer must be inspected on a daily or regular basis. 1. Rating performance Item Dimensions Supply voltage Specifications 75 75 40 mm (excluding protruding parts) 24 VDC (-15% to +10%) Consumption surrent 0.2A max.
-10 to 55No freezing. 25 to 85RH(No dew condensation) Ambient operating temperature Ambient operating humidity Ambient storage temperature Ambient storage humidity Insulation resistance 20M min.with 500 VDC megohmmeter 25 to 85RH(No dew condensation)
-25 to 70No freezing. Dielectric strengh Vibration resistanse Between cable terminals and casing 1000VAC,50/60Hz,1min Between cable terminals and casing 10 to 500 Hz, double amplitude: 1.5 mm, Max. Acceleration: 100m/s2,with 10 sweeps for 11 min. each in 3 directions Shock resistance Mechanical durability: 500m/s2, 3times each in 6 directions Degree of protection Material Mass IP67 (IEC 60529) Oil resistance equivalent to IP67F (JIS C 0920:2003, Appendix 1) Case: PBT resin, Filled resin: Urethane resin Approx. 270 g Mounting method M4 screws Host communication interface Host communication protocol Accessory Please use more than 12 mm of the screw length. EtherNet 10/100BASE-T MODBUS TCP Instruction Seet: 1 sheet Description of Regulations and Standard: 1 sheet IP Address label: 1 sheet 2. Installation M4 screw Spring washer Flat washer Mounting Hole Dimensions 650.2 Four, M4 4. Dimensions 2
. 0 5 6 Seven, Operation indicators 75 65 Four, 4.5-dia. mounting holes
(Unit mm) Standards label Mount the Reader/Writer with four M4 screws with spring washers and flat washers as shown above. Recommended tightening torque: 1.2 Nm Attaching Reader/Writer to the cable 1. Hold the cable connector, and insert the cable connector into the Reader/Writer connector. 2. Turn the threaded portion of the cable connector clockwise to lock it in place. Recommended tightening torque: 0.39 to 0.49 Nm 3. Part Names and functions RF LINK/ACT RUN NORM/ERR NORM/ERR NORM/ERR NORM/ERR Connector 1Connector The connector is used to connect the exclusive cable as model V680S-A40, V680S-A41, or V680S-A42. PIN No. Name Function 1 2 3 4 5 6 24P FG CONT TD-
RD+
+24V Frame ground Control signal Ethernet send data -
Ethernet receive data +
TD+
Ethernet send data +
The color of the wiring of the V680S-A41. Brown
Purple
2 3 4 8 5 1 7 6 7 8 2Status indicators 24N RD-
0V Ethernet receive data -
Blue
The color of the wiring of the V680S-A42. Brown
(Drain wire) Purple Orange Green/White
(stripe) Orange/White
(stripe) Blue Green Name RUN RF NORM/ERR LINK/ACT Color green Flashing green Not lit yellow Not lit green red Flashing red Not lit green Description Lighting while the Reader/Writer is operating normally. Flash while the Reader/Writer is operating in Safe mode. Turn off when power is not supplied. Lighting during communication for RF Tag. Turn off when not in communication with the RF tags. Lighting when the communications finish with no error. Lighting once when an error occurs during communications with the host device, or during communications with an RF Tag. Lighting when unrecoverable error occurs. Flash when recoverable error occurs.
(Configuration memory error, or Control signal wiring mistake, etc.) Turn off when the standby state. Lighting during linking normaly. Flashing green Flash during detects a carrier. Not lit Turn off when the ethernet cable is not connected. 5 7 5 6 2 9
) 7 1
M12 threaded section 9
. 5 6 40 1 3 5
. 7 1 32 Connector Suitability for Use THE PRODUCTS CONTAINED IN THIS SHEET ARE NOT SAFETY RATED. THEY ARE NOT DESIGNED OR RATED FOR ENSURING SAFETY OF PERSONS, AND SHOULD NOT BE RELIED UPON AS A SAFETY COMPONENT OR PROTECTIVE DEVICE FOR SUCH PURPOSES. Please refer to separate catalogs for OMRON's safety rated products. OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of the products in the customer's application or use of the product. Take all necessary steps to determine the suitability of the product for the systems, machines, and equipment with which it will be used. Know and observe all prohibitions of use applicable to this product. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. See also Product catalog for Warranty and Limitation of Liability. EUROPE OMRON EUROPE B.V. Sensor Business Unit Carl-Benz Str.4, D-71154 Nufringen Germany Phone:49-7032-811-0 Fax: 49-7032-811-199 NORTH AMERICA OMRON ELECTRONICS LLC One Commerce Drive Schaumburg,IL 60173-5302 U.S.A. Phone:1-847-843-7900 Fax : 1-847-843-7787 ASIA-PACIFIC OMRON ASIA PACIFIC PTE. LTD. No. 438A Alexandra Road #05-05-08(Lobby 2), Alexandra Technopark, Singapore 119967 Phone : 65-6835-3011 Fax :65-6835-2711 CHINA OMRON(CHINA) CO., LTD. Room 2211, Bank of China Tower, 200 Yin Cheng Zhong Road, PuDong New Area, Shanghai, 200120, China Phone : 86-21-5037-2222 Fax :86-21-5037-2200 OMRON Corporation D OCT, 2009 o The Products conform to the following regulations and standards. 1. /The United States FCC Part 15 Subpart C FCC ID E4EV680S64 FCC ID E4EV680S66
/Reader/Writer V680S-HMD64-ETN V680S-HMD66-ETN
/Regulations and Standards FCC NOTICE This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. /Canada IC ID: 850J-V680S64 IC ID: 850J-V680S66
/Reader/Writer V680S-HMD64-ETN V680S-HMD66-ETN This device complies with Industry Canada Iicence-exempt RSS standards. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.