Oticon Radio Model - Quick Installation Guide Radio Model Name: Oticon BTE SP PEOPLE FIRST The Oticon BTE SP radio model contains two radio transceivers running at 3.84 MHz and 2.4 GHz and both implemented on a single hardware platform. The radio model is implemented in an engine module mounted on the main PCB with connections to the antennas, the microphones, the speaker and the battery terminals. The 3.84 MHz radio is a low power, short range, inductive radio transceiver working at a single channel at 3.84 MHz using MSK modulation with 320 kbit/s data rate and connected to a small coil antenna. The 2.4 GHz radio is a Bluetooth Low Energy (BLE) transceiver using GFSK modulation with 1 Mbit/s data rate also capable of proprietary receiver modes with higher data rates and connected to a short PCB antenna. Oticon A/S Main +45 39 17 71 00 Kongebakken 9 Fax +45 39 27 79 00 DK-2765 Smrum Denmark www.oticon.com CVR-no. 42334219 1 Oticon Radio Model - Quick Installation Guide Radio Model Name: Oticon BTE SP PEOPLE FIRST Below the main flex PCB of the Oticon BTE SP radio model with the most important electrical and electro-mechanical components can be seen:
Oticon BTE SP Radio Model Main PCB Top side The most important part of the radio model is the Engine Module mounted on the main flex PCB, which connects it to both the EEPROM memory and all external connections: On the top side these are the microphones, the battery terminals and the push button. The telecoil is also used for wireless battery charging. The Oticon BTE SP radio model requires only a single cell rechargeable battery and an external speaker (also incl. the wire antenna for the Bluetooth radio part) to be attached and plastic shells, defining the industrial design of a hearing aid end product and holding everything together, in order to be operational. Oticon A/S Main +45 39 17 71 00 Kongebakken 9 Fax +45 39 27 79 00 DK-2765 Smrum Denmark www.oticon.com CVR-no. 42334219 2 Oticon Radio Model - Quick Installation Guide Radio Model Name: Oticon BTE SP PEOPLE FIRST On the bottom side of the main PCB of the Oticon BTE SP radio model the connector for the speaker unit assembly (where the wire antenna for the Bluetooth radio is an integrated part), the programming connector, EEPROM memory and coil antenna for the 3.84 MHz radio can be seen:
The most important parts inside the Engine module are a Digital-Signal-Processor (DSP), a radio Front-End (FE) chip for the 3.84 MHz radio part and an RF chip for the Bluetooth radio part all mounted on a small rigid PCB again mounted on the main flex PCB. The Oticon BTE SP radio model also includes all voltage regulators and buffered data programming inputs on board. The DSP is the main processor controlling the functionality of both radios in the Oticon BTE SP radio model. Oticon BTE SP Radio Model Main PCB Bottom side The Oticon BTE SP radio model is intended to be installed in Oticon, Bernafon, Sonic, SBO Hearing and affiliated wireless hearing aid devices of the Oticon BTE SP (Behind The Ear, Super Power) wearing style. Oticon A/S Main +45 39 17 71 00 Kongebakken 9 Fax +45 39 27 79 00 DK-2765 Smrum Denmark www.oticon.com CVR-no. 42334219 3 Oticon Radio Model - Regulatory Label Information for USA & Canada PEOPLE FIRST Radio Model Name: Oticon BTE SP Contains:
FCC ID:
IC:
U28OTBTESP 1350B-OTBTESP NOTICE:
This device complies with Part 15 of the FCC Rules and with RSS-210 and RSS-247 of Industry Canada. Operation is subject to the following two conditions:
(1)
(2) This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by Oticon A/S may void the FCC authorization to operate this equipment. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. l'appareil ne doit pas produire de brouillage, et l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en L'exploitation est autorise aux deux conditions suivantes:
(1)
(2) compromettre le fonctionnement. Oticon A/S Main +45 39 17 71 00 Kongebakken 9 Fax +45 39 27 79 00 DK-2765 Smrum Denmark www.oticon.com CVR-no. 42334219 4 Oticon Radio Model - Regulatory Label Information for Japan Radio Model Name: Oticon BTE SP Description:
Radio module with 2.4 GHz low power transceiver to be integrated into Oticon, Bernafon, Sonic, and SBO Hearing hearing instruments and associated devices. PEOPLE FIRST NB: The regulatory label for Japan is also included in the IFU for Japan. The grant number is an example. Regulatory label:
This device is granted pursuant to the Japanese Radio Law () under the grant ID n : 202-LSF003
(Example) This device should not be modified (otherwise the granted designation number will become invalid) NB: The regulatory label is not shown on the radio module itself or any end products with it, since they are too small for the label to be readable without any optical aids or magnification. Below the radio module is shown, indicating a size of about 10x15x45 mm. Radio module from the side Radio module from the top side (button side) Oticon A/S Main +45 39 17 71 00 Kongebakken 9 Fax +45 39 27 79 00 DK-2765 Smrum Denmark www.oticon.com CVR-no. 42334219 5