AFTERGLO mal?
COMMUNICATOR FOR PLAYSTATION 3 USER MANUAL Thank you for purchasing the Afterglow Communicator for the PlayStation 3 console. This illuminated wireless Bluetooth headset lets you chat with and send voice messages to other gamers on your PlayStation Network. To chat and send voice messages you need to be signed in to PlayStation Network. This product can also be used with most mobile handsets. WARNING: Before using this product, read this manual as well as the PlayStation 3 console manual for important safety and health information. Keep the manual for future reference. 1, Power/syne/mute button 2. Volume buttons 3. Microphone 4. Operation LEDs 5. Charging port 6. Speaker 7. Ear clip Form and Fit: The Afterglow Bluetooth headset features organic design elements; follow these steps to ensure the most comfortable fit:
1, Slide the ear hook up to the highest position 2. Position the earpiece so it rests lightly in your ear 3. Slide the ear hook down to accommodate your ear size 4. Wrap the ear hook around your ear for comfortable fit WARNING: Please use caution when adjusting the ear hook. You can only adjust the rubberized portion of the ear hook; non-rubberized section might be susceptible to breakage due to excessive force. If you need a replacement ear hook, please contact the PDP support center at 1-800-331-3844
(USA ONLY) ENGLISH Charging Your Communicator: Your Afterglow Communicator should have some charge already when you bought it but it's not 100% charged yet. You can charge your product via PS3 USB ports with the USB cable (provided) or with a USB AC adapter if you have one. It will take approximately 2 hours to fully charge your headset battery. li;
Low Battery Indicator: Once you have about 10% battery power left, your Communicator will warn you visually and audibly. You will see the red LED blinking every 5 seconds. You will also hear a short beep tone every 8 seconds indicating that you're running low on battery. Charging Indicator: While charging you will see the red LED light up. Once the red LED light turns off, the battery is fully charged. NOTE: It is recommended, although not required, to fully charge your headset battery at least every 6 months to ensure the longevity of your battery. Operating Instructions: Pairing is a form of handshake between Bluetooth devices. You will need to pair your Afterglow Communicator with a Bluetooth communication capable device prior to using it, Pairing process is simple. Just follow the below steps. NOTE: Please disconnect the USB charging cable from the Communicator before pairing, as it will not pair while connected.
|\ WARNING: DO NOT USE THE HEADSET NEAR WATER. DO NOT EXPOSE THE HEADSET TO HIGH TEMPERATURES, HIGH HUMIDITY OR DIRECT SUNLIGHT. Pairing yourheadset with.2PS3:
1. Power on your PS3 console. 2. Using your controller, scroll over to Settings on the PS3 menu. 2b. Under Settings, scroll down and select Accessory Settings by pressing (X) on the controller. 3. Within Accessory Settings, scroll down to Manage Bluetooth Devices and select it by pressing (X) on your controller. 4, Within the Manage Bluetooth Devices highlight and select Register New Devices by pressing
(X) on your controller. 4b. A screen will appear with the option to Start Scanning". Do not select t before you initiate the scan, you will need to prepare your headset for pairing. 4c. Make sure that your headset is powered OFF. Press and hold the Power Button of your Afterglow Communicator, for approximately 7 seconds until the board color LED & red LEDs light up and flash alternately. This means your headset is looking for a device to pai 5. Back at the PS3 screen, select Start Scanning by pressing the (X) button on the controller. 6. PS3 should automatically find and display your product name on screen as Afterglow?
Communicator. Select it (by pressing the (X) button on the controller. 7. You'll be prompted to enter a Pass Key to authenticate the pairing headset. This code is
"0000". 8. This completes the pairing process. You should see Register completed on your screen. 9, The Headset is registered and ready for activation. Go to Settings, scroll down to and select Accessory Settings, scroll down to and select Audio Device Settings. Here you will be able to. set your Microphone Level, as well as activate your headsets Input Device (Microphone) and Output Device (Speaker). Highlight and select Audio Device Settings by pressing the (X) button on the controller. You will see 3 options (Microphone, Level - Input Device ~ Output Device). 9b. Highlight Input Device and select it by pressing (X) on the controller. Scroll up to Afterglow?
Bluetooth Communicator. A Blue dot will appear near the name of the active device. Press (X) to confirm the device. option yet;
ENGLISH Qc. If the Output Device Doesn't automatically change to Afterglow Bluetooth Communicator", highlight and select Output Device and scroll up to Afterglow Bluetooth Communicator and press (X) to confirm the devi 9d. Highlight and select OK by pressing (X) on your controller to confirm settings. 9e. A successfully paired Afterglow Communicator will have its board color LED light flash every 8 seconds. PLEASE NOTE: There are only a limited number of Bluetooth headsets your PS3 can keep in its memory. If you previously paired many headsets you may not be able to register this new headset prior to deleting one of the old ones. You can do this by going over to the Manage Bluetooth Devices section, highlighting the inactive headset, pressing the triangle button and selecting delete. Pairing your headset with a mobile phon 1. Put your Afterglow Communicator in pairing mode by pressing and holding the Power Button of your Afterglow Communicator, for approximately 7 seconds until the board color LED & red LEDs ht up and flash alternately. This means your headset is looking for a device to pair. 2. From your mobile phone settings menu, seek a Bluetooth device in pairing mode. Once you see Afterglow? Bluetooth Communicator name displayed, select 3. Enter the password which is 0000. Some mobile phones dont ask for this password but ask a question instead such as Afterglow Communicator wants to pair; do you accept? Just accept it. NOTE: Your headset can remain in the pairing mode for 2 minutes. If within these 2 minutes you haven't successfully paired it with a PS3 or a mobile headset you need to put it back in the pairing mode again by pressing the power button for 7 seconds. Muting: Your Afterglow Communicators power button also doubles as a mute button. When Afterglow Communicator is turned on and paired, press it once to mute the microphone. Press it once more to un-mute. While muted you can still hear the incoming audio. PS3 or Mobile Phone turned off: If your Afterglow Communicator is on and paired to the PS3 (or Mobile Phone) and the PS3 (or Mobile Phone) is turned off, you will notice the LEDs flash pattern change. The board color LED and the red LED will flash together followed by a quick board color LED flash. This is indicating that system the communicator is paired with is currently off. If you no longer plan on using the Afterglow Communicator, please turn it off to save battery life. TROUBLESHOOTING:
+ cant see the headset in device menu wi 2 minutes. Make sure you set your PS3 or mobi this 2 minutes. Make sure you are in pairing mode by confirming you can see alternately flashing board color LED and red LED lights.
+ Icant see the red charging light: Your battery might be completely dri for few minutes, then you should be seeing the red charging indication
+ leant hear people: Check your volume level, you might be very low. Increase the volume level by pressing + button. Make sure you properly paired the headset and your board color LED is flashing every 4 seconds. Make sure your headset is paired with the device you intend to use it with.
+ People cant hear me: Make sure you have not muted the headset. Make sure you're speaking clearly while the pointing towards your mouth.
+ Lost connection: Your Afterglow Communicator has a range of 10 meters or approximately 30 feet. This distance may vary depending on the walls or other obstructions between the headset and the paired device. If you move out of range you will not hear incoming chat and nobody will hear you either. Stay within the communication range while you're operating this product. If you walk out of range and re-enter, Afterglow Communicator should reconnect to the device it was last synced to but in case it doesnt, go through the pairing process again. Still having issues? Call the PDP support center at ... 1-800-331-3844 (USA ONLY) ing: Your headset stays in pairing mode for phone to look for the pairing device within ined. Allow it to charge ENGLISH NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. MODIFICATIONS WILL VOID THE USER AUTHORITY TO OPERATE THE EQUIPMENT.
{\CAUTION: Changes or modifications to this equipment not expressly approved by the manufacturer could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is. encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the re is connected Consult the dealer or an experienced radio/TV technician for help. FCC ID for Headset: X5B-PL6360A This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Se Sua ica}
ey Vernon, CA 90058 USA Cee eee etre) Cid Windsor Rees ear OOP ee eet) Prater eater kr CE eae ae enn ry igned Products, PDP, Afterglow and their respective logos ee ere arene er an nares Creme teratoma oe ee eee pen ere ee eae) eran) trademarks of Sony Computer Entertainment, Inc. This product is not designed, manufactued, sponsored or endorsed by Sony. nee)