FCC ID: 2ASIVPGA300RF Wireless Transceiver

R REV0.1 ERPPLA3544Q-GL-SMT00030A-V1 ERP P/N:

PLA3544Q/PGA300RF,STM000,REV.B,160x80mm,80G,

, ROHS2.0,REACH,POPs,PAHS,PROP65, 80x40mm DesignedWalter Date2022-05-07 K WWW.LOCKLYPRO.COM Lockly Guard Wireless Transceiver is built with F433.92MHz and Lockly 2.0 proprietary encryption to provide stable wireless connectivity, security and reliability. It operates on 12V DC from the Access Control power supply and supports high-level or low-level of PUSH and monitors door open/closed status of the electromagnetic lock*. It is very quick and easy to install anywhere. 1. To remove cover, slide the bottom of the case as shown. 2. Refer to the wiring diagram Insert cables through the bottom hole and connect to corresponding wireless transceiver terminals : PUSH GND, GND, +12V and LOCK NC. Then connect the cables to the corresponding terminals on the Access Control Power Supply : PUSH, V-, V+ and LOCK NC to electromagnetic lock NC terminal. Ensure you followed the wiring diagram and cables are connect-

ed to the corresponding terminals. Tighten the screws to secure the cables. Access Control Power Supply WIRELESS TRANSCEIVER (PGA300RF) Installation & User Manual Note The NC port is used to detect the opening and closing status of the door. Only the Lockly Guard Electromagnetic Lock supports this function. If you use a third-party Electromagnetic Lock other than the Lockly Guard Electromagnetic Lock, you do not need to connect this NC cable.

*Works ONLY with Lockly Electromagnetic Lock. Connection to NC of the LOCK NC cable is required. 3. Pair Wireless Transceiver to the Lockly Guard Ingress or Ingress Vision Access Control power supply will activate the Wireless Transceiver. Wireless Transceiver Blue light indicator will be ON once connected to Ingress or Ingress Vision. Refer to the Ingress/Ingress Vision Manual for pairing instructions. Short Press the wireless transceiver pairing button to start connecting with Ingress/Vision, Blue light indicator flashes when pairing starts. It will automatically exit pairing mode if pairing is successful. If pairing is unsuccessful, it will continue to flash and automatically exits in 3 minutes. Short press the wireless transceiver pairing button again to re-enter pairing mode.

+12V GND PUSH GND PUSH 12V LOCK NC 4. How Wireless Transceiver and Ingress/Ingress Vision Works 1) When wireless transceiver is activated through the smart access control power supply, the Blue light indicator turns ON when the door locks or unlocks. 2) When the electromagnetic lock (LOCK NC) is triggered, the Blue light indicator turns ON. Electromagnetic Lock Wirelless Transceiver FCC Warning:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement The Secure Link Wi-Fi Hub complies with FCC radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with minimum distance 20cm between the radiator & your body. licence-exempt IC WARNING that comply with This device contains Innovation,Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. transmitter(s) Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. IC Radiation Exposure Statement This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102. It should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. Cet quipement est conforme l'exemption des limites d'valuation habituelle de la section 2.5 de la norme RSS-102. Il doit tre install et utilis une distance minimale de 20 cm entre le radiateur et toute partie de votre corps. WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.

Reference No.: WTX22X01008675W-1 Page 1 of 8 ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the devices expected lifetime. Proposed Label Location on EUT FCC ID Label Location Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn

PIN GENIE, INC. DBA LOCKLY 676 Transfer Rd., St. Paul, MN 55114, United States

Date: 2022-05-06 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2ASIVPGA300RF Confidentiality Request To whom it may concern, Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of the information accompanying this application as outlined below:

Block Diagram Operational Description Schematics Parts List Tune-Up Information Security Information Software Defined Radio (SDR) Information The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, PIN GENIE, INC. DBA LOCKLY

(Cindy zhou)

(COO)

PIN GENIE, INC. DBA LOCKLY 676 Transfer Rd., St. Paul, MN 55114, United States

(FCC ID2ASIVPGA300RF) POWER OF ATTORNEY DATE: 2022-05-06 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, PIN GENIE, INC. DBA LOCKLY are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, PIN GENIE, INC. DBA LOCKLY

(Cindy zhou)

(COO)