FCC ID: AJDK118 RDS AV RECEIVER with BT and WIFI

DMH-2770NEX DMH-2700NEX RDS AV RECEIVER RCEPTEUR AV AVEC RDS RECEPTOR AV RDS E n g l i s h F r a n a i s E s p a o l Installation Manual Manuel dinstallation Manual de instalacin X:\print\Pioneer\21_ODM\KB010\INST\KB010_UC_INST(A5_Horizon)\020Chapter_EN.fm _INSTM_DMH1700NEXUC_A_artwork.book Page 2 Tuesday, November 10, 2020 2:12 PM Important safety information WARNING Rear visibility systems (backup cameras) are required in certain new vehicles sold in the U.S. and Canada. U.S. regulations began according to a two year phase-in on May 1, 2016, and both the U.S. and Canada require that all such vehicles manufactured on or after May 1, 2018 have rear visibility systems. Owners of vehicles equipped with compliant rear visibility systems should not install or use this product in a way that alters or disables that system's compliance with applicable regulations. If you are unsure whether your vehicle has a rear visibility system subject to the U.S. or Canadian regulations, please contact the vehicle manufacturer or dealer. If your vehicle has a compliant backup camera that displays the backup view through the factory receiver, do not use the Pioneer receiver unless it is connected to and displays the same view as the factory backup camera. Connection to the factory backup camera will require an adaptor, sold separately. Not all vehicles may be able to connect. Please check with a qualified professional installer for installation options specific to your vehicle. Connection Precautions Your new product and this manual Do not operate this product, any applications, or the rear view camera option (if purchased) if doing so will divert your attention in any way from the safe operation of your vehicle. Always observe safe driving rules and follow all existing traffic regulations. If you experience difficulty in operating this 2 En product, pull over, park your vehicle in a safe location and apply the parking brake before making the necessary adjustments. Do not install this product where it may

(i) obstruct the drivers vision,

(ii) impair the performance of any of the vehicles operating systems of safety features, including airbags, hazard lamp buttons, or

(iii) impair the drivers ability to safely operate the vehicle. In some cases, it may not be possible to install this product because of the vehicle type or the shape of the vehicle interior. Important safeguards WARNING Pioneer does not recommend that you install this product yourself. This product is designed for professional installation only. We recommend that only authorized Pioneer service personnel, who have special training and experience in mobile electronics, set up and install this product. NEVER SERVICE THIS PRODUCT YOURSELF. Installing or servicing this product and its connecting cables may expose you to the risk of electric shock or other hazards, and can cause damage to this product that is not covered by warranty. Precautions before connecting the system WARNING Do not take any steps to tamper with or disable the parking brake interlock system which is in place for your protection. Tampering with or disabling the parking brake interlock system could result in serious injury or death. CAUTION Secure all wiring with cable clamps or electrical tape. Do not allow any bare wiring to remain exposed. Do not directly connect the yellow lead of this product to the vehicle battery. If the lead is directly connected to the battery, engine vibration may eventually cause the insulation to fail at the point where the wire passes from the passenger compartment into the engine compartment. If the yellow leads insulation tears as a result of contact with metal parts, short-circuiting can occur, resulting in considerable danger. It is extremely dangerous to allow cables to become wound around the steering column or shift lever. Be sure to install this product, its cables, and wiring away in such so that they will not obstruct or hinder driving. Make sure that the cables and wires will not interfere with or become caught in any of the vehicles moving parts, especially the steering wheel, shift lever, parking brake, sliding seat tracks, doors, or any of the vehicles controls. Do not route wires where they will be exposed to high temperatures. If the insulation heats up, wires may become damaged, resulting in a short circuit or malfunction and permanent damage to the product. Do not shorten any leads. If you do, the protection circuit (fuse holder, fuse resistor or filter, etc.) may fail to work properly. Never feed power to other electronic products by cutting the insulation of the power supply lead of this product and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating. Before installing this product Use this unit with a 12-volt battery and negative grounding only. Failure to do so may result in a fire or malfunction. To avoid shorts in the electrical system, be sure to disconnect the () battery cable before installation. To prevent damage WARNING When speaker output is used by 4 channels , use speakers over 50 W DMH-1770NEX/DMH-1700NEX/DMH-160BT KB010_UC_INST(A5_Horizon)

(Maximum input power) and between 4 to 8 (impedance value). Do not use 1 to 3 speakers for this unit. The black cable is ground. When installing this unit or power amp (sold separately), make sure to connect the ground wire first. Ensure that the ground wire is properly connected to metal parts of the cars body. The ground wire of the power amp and the one of this unit or any other device must be connected to the car separately with different screws. If the screw for the ground wire loosens or falls out, it could result in fire generation of smoke or malfunction. Ground wire POWER AMP Other devices

(Another electronic device in the car) Metal parts of cars body

*1 Non supplied for this unit When replacing the fuse, be sure to only use a fuse of the rating prescribed on this product. This product cannot be installed in a vehicle without ACC (accessory) position on the ignition switch. ACC position No ACC position To avoid short-circuiting, cover the disconnected lead with insulating tape. It is especially important to insulate all unused speaker leads, which if left uncovered may cause a short circuit. For connecting a power amp or other devices to this product, refer to the manual for the product to be connected. The graphical symbol placed on the product means direct current. Notice for the blue/

white lead When the ignition switch is turned on

(ACC ON), a control signal is output through the blue/white lead. Connect to an external power amps system remote control terminal, the auto-antenna relay control terminal, or the antenna booster power control terminal (max. 300 mA 12 V DC). The control signal is output through the blue/white lead, even if the audio source is switched off. This product Be sure to use the Sirius XM cable (Sirius XM Tuner Only) supplied with this product. Refer to the instruction manual for SiriusXM Connect Vehicle Tuner (sold separately). Fuse (10 A) Power supply To connector 1 Wired remote input (STEERING WHEEL CONTROL) Hard-wired remote control adapter can be connected (sold separately). Brown (REAR VIEW CAMERA IN) Yellow/black (MUTE) GPS antenna 3.55 m Power cord E n g l i s h Black (ground) To vehicle (metal) body. Violet/white Of the two lead wires connected to the back lamp, connect the one in which the voltage changes when the gear shift is in the REVERSE (R) position. This connection enables the unit to sense whether the car is moving forward or backward. Pink Car speed signal input Blue/white Connect to system control terminal of the power amp (max. 300 mA 12 V DC). Light green Used to detect the ON/OFF status of the parking brake. This lead must be connected to the power supply side of the parking brake switch. Power supply side Parking brake switch Ground side Speaker leads Microphone 3 m (9 ft. 10-1/8 in.) This product Antenna jack Connector 1 (REAR VIEW CAMERA IN/

MUTE/STEERING WHEEL CONTROL) Connector 2 (AUX IN) Pre out supply SiriusXM Connect Vehicle Tuner To power supply Power cord Yellow To terminal supplied with power regardless of ignition switch position. Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF Orange/white To lighting switch terminal. To power supply Power cord Left Right Front speaker Rear speaker 3En X:\print\Pioneer\21_ODM\KB010\INST\KB010_UC_INST(A5_Horizon)\020Chapter_EN.fm _INSTM_DMH1700NEXUC_A_artwork.book Page 4 Tuesday, November 10, 2020 2:12 PM White White/black Gray Gray/black Green Green/black Violet Violet/black NOTE With a two-speaker system, do not connect anything to the speaker leads that are not connected to speakers. Power amp (sold separately) Important The speaker leads are not used when this connection is in use. 4 En Subwoofer output (SUBWOOFER OUT L/SUBWOOFER OUT R) RCA cable (sold separately) Power amp Front output (FRONT OUT L/FRONT OUT R) Rear output (REAR OUT L/REAR OUT R) Yellow/black (MUTE) If you use an equipment with Mute function, wire this lead to the Audio Mute lead on that equipment. If not, keep the Audio Mute lead free of any connections. Pre out cord To pre out supply To connector 1 System remote control Connect to Blue/white cable. Rear speaker Front speaker DMH-1770NEX/DMH-1700NEX/DMH-160BT KB010_UC_INST(A5_Horizon) X:\print\Pioneer\21_ODM\KB010\INST\KB010_UC_INST(A5_Horizon)\020Chapter_EN.fm _INSTM_DMH1700NEXUC_A_artwork.book Page 5 Tuesday, November 10, 2020 2:12 PM Subwoofer iPhone and smartphone Smartphone (Android device) NOTES For details on how to connect an external device using a separately sold cable, refer to the manual for the cable. For details concerning the connection and operations of iPhone or smartphone, refer to the Operation Manual. iPhone with Lightning connector Connecting via the USB port iPhone with Lightning connector USB interface cable for iPhone (sold separately) USB cable 1.5 m (4 ft. 11 in.) USB port Connecting via the USB port E n g l i s h Smartphone USB - micro USB cable (Type USB A -

micro USB B) (sold separately) USB Type-C cable (Type USB A - USB C)

(sold separately) USB cable 1.5 m (4 ft. 11 in.) USB port NOTES The length of Type USB A - micro USB B cable cannot exceed 2 m (6 ft. 6 in.) and Type USB A - USB C cannot exceed 4 m

(13 ft. 1 in.) according to the USB cable standard. When using a cable other than the above conditions, the main unit function may not operate properly. Android is a trademark of Google LLC. Camera About rear view camera When you use the rear view camera, the rear view image is automatically switched from the video by moving the shift lever to REVERSE (R). Camera View mode also allows you to check what is behind you while driving. 5 En DMH-1770NEX/DMH-1700NEX/DMH-160BT KB010_UC_INST(A5_Horizon) X:\print\Pioneer\21_ODM\KB010\INST\KB010_UC_INST(A5_Horizon)\020Chapter_EN.fm _INSTM_DMH1700NEXUC_A_artwork.book Page 6 Tuesday, November 10, 2020 2:12 PM WARNING USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY RESULT IN INJURY OR DAMAGE. CAUTION The screen image may appear reversed. With the rear view camera you can keep an eye on trailers, or back into a tight parking spot. Do not use for entertainment purposes. Objects in rear view may appear closer or more distant than in reality. The image area of full-screen images displayed while backing or checking the rear of the vehicle may differ slightly. Refer to Power cord on page 3. RCA cable (sold separately) To video output Rear view camera (sold separately) NOTES Connect only the rear view camera to REAR VIEW CAMERA IN. Do not connect any other equipment. Some appropriate settings are required to use rear view cameras. For details, refer to the Operation Manual. External video component and the display This product Connector 1 Power supply To connector 1 To power supply Power cord Brown (REAR VIEW CAMERA IN) Violet/white (REVERSE-GEAR SIGNAL INPUT) 6 En This product Pre out supply Connector 2 To connector 2 To pre out supply Pre out cord Mini-jack AV cable (sold separately) AUX input (AUX IN) Yellow (REAR MONITOR OUT) Yellow Red, white RCA cables (sold separately) To video input Rear display with RCA input jacks To video output To audio outputs External video component (sold separately) NOTE The appropriate setting is required to use the external video component. For details, refer to the Operation Manual. WARNING NEVER install the rear display in a location that enables the driver to watch the video source while driving. This products rear video output is for connection of a display to enable passengers in the rear seats to watch the video source. CAUTION Be sure to use a mini-jack AV cable (sold separately) for wiring. If you use other cables, the wiring position might differ resulting in disturbed images and sounds. L : Left audio (White) R : Right audio (Red) V : Video (Yellow) G : Ground DMH-1770NEX/DMH-1700NEX/DMH-160BT KB010_UC_INST(A5_Horizon) X:\print\Pioneer\21_ODM\KB010\INST\KB010_UC_INST(A5_Horizon)\020Chapter_EN.fm _INSTM_DMH1700NEXUC_A_artwork.book Page 7 Tuesday, November 10, 2020 2:12 PM Installation Precautions before installation CAUTION Never install this product in places where, or in a manner that:

Could injure the driver or passengers if the vehicle stops suddenly. May interfere with the drivers operation of the vehicle, such as on the floor in front of the drivers seat, or close to the steering wheel or shift lever. To ensure proper installation, be sure to use the supplied parts in the manner specified. If any parts are not supplied with this product, use compatible parts in the manner specified after you have the part compatibility checked by your dealer. If parts other than supplied or compatible ones are used, they may damage internal parts of this product or they may work loose and the product may become detached. Do not install this product where it may

(i) obstruct the drivers vision,

(ii) impair the performance of any of the vehicles operating systems or safety features, including airbags, hazard lamp buttons or

(iii) impair the drivers ability to safely operate the vehicle. Never install this product in front of or next to the place in the dashboard, door, or pillar from which one of your vehicles airbags would deploy. Please refer to your vehicles owners manual for reference to the deployment area of the frontal airbags. Before installing Consult with your nearest dealer if installation requires drilling holes or other modifications of the vehicle. Before making a final installation of this product, temporarily connect the wiring to confirm that the connections are correct and the system works properly. Installation notes Do not install this product in places subject to high temperatures or humidity, such as:

Places close to a heater, vent or air conditioner. Places exposed to direct sunlight, such as on top of the dashboard. Places that may be exposed to rain, such as close to the door or on the vehicles floor. Install this product horizontally on a surface within 0 to 60 degrees tolerance. 5 cm Leave ample space 5 cm Installation using the screw holes on the side of this product 1 Fastening this product to the factory radio-mounting bracket. Position this product so that its screw holes are aligned with the screw holes of the bracket, and tighten the screws at three locations on each side. Use either the truss head screws (5 mm 9 mm) or flush surface screws (5 mm 9 mm), depending on the shape of the brackets screw holes. When installing, to ensure proper heat dispersal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents. TIP The amount of this unit's protrusion from the dashboard/console can be adjusted by shifting the position of the screw hole of this unit to the factory radio-mounting bracket. E n g l i s h Factory radio-mounting bracket If the pawl interferes with installation, you may bend it down out of the way. Dashboard or console Truss head screw or flush surface screw Be sure to use the screws supplied with this product. Installing the microphone Install the microphone in a place where its direction and distance from the driver make it easiest to pick up the drivers voice. Be sure to turn off (ACC OFF) the product before connecting the microphone. Depending on the vehicle model, the microphone cable length may be too short when you mount the microphone on the sun visor. In such cases, install the microphone on the steering column. 7 En DMH-1770NEX/DMH-1700NEX/DMH-160BT KB010_UC_INST(A5_Horizon) X:\print\Pioneer\21_ODM\KB010\INST\KB010_UC_INST(A5_Horizon)\020Chapter_EN.fm _INSTM_DMH1700NEXUC_A_artwork.book Page 8 Tuesday, November 10, 2020 2:12 PM Mounting on the sun visor Installation on the steering column Adjusting the microphone angle 1 Fit the microphone lead into the 1 Detach the microphone base from the The microphone angle can be adjusted. groove. microphone clip by sliding the microphone base while pressing the tab. Microphone lead Groove 2 Attach the microphone clip to the sun visor. Tab Microphone base 2 Mount the microphone on the steering column. Microphone clip Clamps Use separately sold clamps to secure the lead where necessary inside the vehicle. Install the microphone on the sun visor when it is in the up position. It cannot recognise the drivers voice if the sun visor is in the down position. Double-sided tape Clamps Use separately sold clamps to secure the lead where necessary inside the vehicle. NOTE Install the microphone on the steering column, keeping it away from the steering wheel. 8 En DMH-1770NEX/DMH-1700NEX/DMH-160BT KB010_UC_INST(A5_Horizon) X:\print\Pioneer\21_ODM\KB010\INST\KB010_UC_INST(A5_Horizon)\020Chapter_EN.fm _INSTM_DMH1700NEXUC_A_artwork.book Page 9 Tuesday, November 10, 2020 2:12 PM E n g l i s h 9 En DMH-1770NEX/DMH-1700NEX/DMH-160BT KB010_UC_INST(A5_Horizon) 2022 PIONEER CORPORATION

<INSTM_DMH2700NEXUC_A> UC

RDS AV RECEIVER RCEPTEUR AV AVEC RDS RECEPTOR AV RDS DMH-W2770NEX DMH-W2700NEX Quick start guide Guide de dmarrage rapide Gua de inicio rpido Franais Ce guide est destin vous guider dans les fonctions de base de cet appareil. Pour les dtails, veuillez vous reporter au Mode demploi disponible sur le site Web. https://www.pioneerelectronics.com/PUSA/

English This guide is intended to guide you through the basic functions of this unit. For details, please refer to the Operation manual stored on the website. https://www.pioneerelectronics.com/PUSA/

https://www.pioneerelectronics.ca/POCEN/

English Precaution Information to user https://www.pioneerelectronics.ca/POCEN/

Espaol https://www.pioneerelectronics.ca/POCEN/

Para obtener ms informacin, consulte el manual de operaciones que se encuentra en el sitio web. connected. Consult the dealer or an experienced radio/TV technician for help. https://www.pioneerelectronics.com/PUSA/

This device contains licence-exempt transmitter(s)/receiver(s) that complies with Part 15 of FCC Rules and Innovation, Science, and Economic Development Canada licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of this device. The Bluetooth antenna cannot be removed (or replaced) by user. This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules.This equipment should be installed and operated keeping the radiator at least 20 cm or more away from person's body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Information to User - Alteration or modifications carried out without appropriate authorization may invalidate the users right to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is FEDERAL COMMUNICATIONS COMMISSION SUPPLIER'S DECLARATION OF CONFORMITY Product Name: RDS AV RECEIVER Model Number: DMH-W2770NEX, DMH-W2700NEX Responsible Party Name: PIONEER ELECTRONICS (USA) INC. SERVICE SUPPORT DIVISION Address: 2050 W. 190TH STREET, SUITE 100, TORRANCE, CA 90504, U.S.A. Phone: 1-800-421-1404 URL: http://www.pioneerelectronics.com WARNING Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as papers, floor mat, cloths). CAUTION This product is evaluated in moderate and tropical climate condition under the Audio, video and similar electronic apparatus - Safety requirements, IEC 60065. The Safety of Your Ears is in Your Hands Get the most out of your equipment by playing it at a safe levela level that lets the sound come through clearly without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing. Sound can be deceiving. Over time, your hearing comfort level adapts to higher volumes of sound, so what sounds normal can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts. ESTABLISH A SAFE LEVEL:

Set your volume control at a low setting. Slowly increase the sound until you can hear it comfortably and clearly, without Once you have established a comfortable sound level, set the dial and leave it distortion. there. BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:

Do not turn up the volume so high that you cant hear whats around you. Use caution or temporarily discontinue use in potentially hazardous situations. Do not use headphones while operating a motorized vehicle; the use of headphones may create a traffic hazard and is illegal in many areas. CAN ICES-3 B/NMB-3 B

<QSG_DMHW2700NEXUC_A>

English Whats What Touch Touch and slide Touch and hold Selecting the clock Tuner operation Moving images operation Audio operation List search operation Display off Power off Display the top menu screen Mute or unmute Activate the voice recognition mode VOL (+/-) Switch to clock adjustment display Adjust the clock Selecting the source Select a source Store the strongest broadcast frequencies Select a band Tune into the next station Recall the preset channel stored to a key from memory Store the current broadcast frequency to a key Displays a preset channel for 10 seconds and switches to the next channel automatically. Tune into only radio stations with sufficiently strong signals Start seek turning Pause and start playback Change the playback point Selects the previous file or the next file. Performs fast forward or fast reverse. Touch again to change the playback speed. Pause and start playback Selects the previous file or the next file. Performs fast forward or fast reverse. Touch again to change the playback speed. Set the function for playing audio Display the playlist screen Select the media file types Select a list title or folder that you want to play Scroll the list Enter the phone number directly Switch to the phone book mode Switch to the call history list Make an outgoing call

[Wi-Fi Settings]

Wi-Fi connection 1 Turn on the Wi-Fi function on the device. 2 3 Set [Wi-Fi] to on. 4 Check the password in the [Password] menu. 5 6 Check the [Network Name] and select the network name on the mobile device. 7 Input the password displayed in [Password] on the mobile device.

[Device Information]

[Bluetooth Settings]

Bluetooth connection 1 2 NOTE The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Pioneer Corporation is under license. Other trademarks and trade names are those of their respective owners. the Bluetooth device name.

[Search]. Bluetooth telephone operation

851mm _ PICNESE _ Woce\nodste: DMH-W2770NEX pe

(eK 8 84938947893" 9 i MADE IN THABANDIFABRIQUE EN THAILANDE PIONEER CORPORATION KB021DXNUC-LABEL-A PIONEE _sosewWosele: D 9c, 144 IMIH-W2700NEX c.caisav FCC ID:AJDK118 CANICES-3 B/NMB-3 B Ic: T75E-K118 HUG. MADE IN THAILANDIFABRIQUE EN THATLANDE KB021XNUC-LABEL-A qe my 8 9 8493847893 PIONEER CORPORATION

PIONEER CORPORATION Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: AJDK118. Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type

(Block Diagram, Schematics, Operational Description, Parts List, Tune Up ) File Name

(1.Block Diagram.pdf; 4.MB_P4_sch.pdf;

3.Operation Description.pdf; 2.BOM.pdf; 8. Tuneup.pdf;) The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below:

Time180days Exhibit Type

(External Photos, Internal Photos, Test Setup Photos, Manual) File Name

(Appendix A.1-External Photos.pdf; Appendix A.2-Internal Photos.pdf; Appendix A.3-Test setup.pdf; Appendix D Photographs-.pdf; 7. User Manual.pdf;) Sincerely, Date:

City:

Name:

15/09/2021 Tokyo Takashi Tsuzura Function:

Manager Signature:

Rev 11/20/07

RF_160, Issue 04 PIONEER CORPORATION Declaration of Authorization We Name:

Address:

City:

Country:

Declare that:

PIONEER CORPORATION 28-8, Honkomagome 2-Chome, Bunkyo-ku, Tokyo 113-0021, Japan Tokyo Japan Name Representative of agent:

Agent Company name:

Address:

Nanshan District, Shenzhen, Guangdong, China. City:

Country Shenzhen China Chris You CCIC Southern Testing Co., Ltd. Electronic Testing Building, No. 43 Shahe Road, Xili Street, is authorized to apply for Certification of the following product(s):

Product description: RDS AV RECEIVER Type designation:

Trademark:

FCC ID :

on our behalf. DMH-W2700NEX / DMH-W2770NEX Pioneer AJDK118 Date:

Email:

Name:

15/09/2021 takashi_tsuzura@post.pioneer.co.jp Takashi Tsuzura (2) Function:

Manager Signature:

Notes:

(1): Required for FCC application

(2): For FCC it must be the Grantee Code owner or the authorized agent.

PIONEER CORPORATION 28-8, Honkomagome 2-Chome, Bunkyo-ku, Tokyo 113-0021, Japan To who it may concern:

We, PIONEER CORPORATION, declare that we are solely responsible for The product differences between DMH-W2770NEX and DMH-W2700NEX are as follows:

Model name DMH-W2770NEX DMH-W2700NEX HW/SW The same The same remote control(without RF function) With without Except listings above, the others are all the same as previous version. Should you have any questions or comments regarding this matter, please have my best attention.

PIONEER CORPORATION 28-8, Honkomagome 2-Chome, Bunkyo-ku, Tokyo 113-0021, Japan UNII Declaration Letter We have declared below featured for FCC equipment authorization, device FCC ID:AJDK118

(1) DFS Device --

Master, Client without radar detection capability, Client with Radar detection capability , N/A

(2) Active / Passive Scanning , adhoc mode access point capability Frequency Band

(MHz) Active Scanning

(the device can transmit a probe

(beacon)) 5745 MHz Yes, No passive scanning

(where the device is can listen only with no probes) Yes, No Yes, Ad Hoc Mode capability Access point capability No Yes, No

(3) Country code selection ability -

If no, pls explain how was implemented : use Microsoft network utility Yes , No

(4) Meet 15.202 requirement - Yes , pls check below :

No , A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network.

(5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes can not be modified by end user or an installer. Apply , No Apply ,

(If apply , pls help to provide explanation on how it was implement (By hardware or software , and how software was controlled) If you have any questions, please feel free to contact me at the address shown below. Yours sincerely, Date:

15/09/2021 Email:

Name:

takashi_tsuzura@post.pioneer.co.jp Takashi Tsuzura Function:

Manager Signature: