1 Please note your phone is battery-embedded design with removable battery and battery cover. Unauthorized personnel are strictly prohibited from disassembling the phone. Make sure to use only the power adapter (5V 2A Output AC/DC) that came with PM90. In case your phone does not work as expected, you are strongly recommended to restart it by pressing and holding the power button for at least 12 seconds until the startup screen appears. If your phone has encountered a serious error and cannot be recovered, you should reset your phone to factory settings by using the menu, either Backup & Reset, or Factory Reset. For more details, please refer to Factory data reset section on page 32. Note: Please be cautious while performing the factory data reset. Because this will erase personalized settings and data saved in your phone, such as SMS, Contacts, Music, etc. www.sar-tick.com Body-worn Operation This device was tested for typical bodyworn operations with the Front & back of the device kept 0.59 inches (1.5cm) between the users body and the Front & back of the device. To comply with FCC RF exposure requirements, a minimum separation distance of 0.59 inches (1.5cm) must be maintained between the users body and the Front & back of the device. Any beltclips, holsters, and similar accessories containing metallic components may not be used. Body-worn accessories that cannot maintain 0.59 inches (1.5cm) separation distance between the users body and the Front & back of the device, and have not been tested for typical body-
worn operations may not comply with FCC RF exposure limits and should be avoided. PROTECT YOUR HEARING To prevent possible hearing damage, do not listen at high volume levels for long periods. Exercise caution when holding your device near your ear while the loudspeaker is in use. 2 Table of Contents Table of Contents ............................................... 3 1 2 Accessary ............................................. 5 Setup PM90 .......................................... 6 2.1 Remove the Battery Cover ......................... 6 2.2 Insert the Battery ................................... 7 2.3 Close the Battery Cover ............................ 7 2.4 Insert and Remove the SIM-SAM card ............ 8 2.5 3 4 Install and Remove the microSD card ............. 9 Charge PM90 ...................................... 10 Turn On/Off PM90 ................................ 11 3 1 Major Parts 1 Display, Touch panel 9 Power button 2 Receiver 3 Front camera 4 Buttons 5 Scan window 6 Volume button 7 Left scan button 8 Right scan button Earphone cover Rear camera Speaker Battery cover Battery cover locker USB port cover Charging cradle connector 10 11 12 13 14 15 16 4 2 Accessary 5V 2.0A AC/DC Adapter Micro USB C Type Cable AC plug (US/EU/UK) Battery (2900mAh) Battery (5800mAh) Stylus Wrist landyard LCD protection film 5 3 Setup PM90 2.1 Remove the Battery Cover 1. Slide the Battery locker. 2. Lift up the Battery Cover. 3. Remove the Battery Cover. 6 2.2 Insert the Battery Insert Battery from top area. 2.3 Close the Battery Cover Insert Battery Cover from top area first and then put in bottom area. Press battery cover with both hand firmly. 7 2.4 Insert and Remove the SIM-SAM card You must insert your SIM card to make phone calls. Please power off your phone before inserting or removing the SIM card. 1. Remove the Battery Cover and the Battery. 2. Lift up the SIM rubber. 3. Insert the SIM-SAM card into the slot. (Gold plate should face down). Make sure that it is correctly inserted. 4. To remove the card, repeat step1 and step2, then remove the card out of the slot. Note: Your device only supports SIM cards. Do not attempt to insert other SIM types such as Micro and Nano SIM card, this may cause damage to your device. If you have to use different SIM card types, please use SIM adaptor. 8 2.5 Install and Remove the microSD card 1. Remove the Battery Cover and the Battery. 2. Lift up the SIM rubber. 3. Insert the microSD card into the slot (Gold plate should face down). 4. To remove the microSD card, repeat step1 and step2, then remove the card out of the slot. Note: To avoid data loss and SD card damage, please power off your phone before inserting or removing the SD card. 9 3 Charge PM90 1. Connect the AC/DC adaptor to your device and wall socket respectively. 2. LED indicator will display charging status. Steady Red Battery is charging or Battery level is low Blinking Red Battery level is critical low Steady Green Battery is fully charged PM90 Battery Specification Standard Battery 2,900mAh 3.85V Backup Battery 5,800mAh 3.85V Charging time About 5 hours Note: Always use an original charger and cable from the Point Mobile. Other chargers and cables may damage PM90. In addition, make sure connector, charger, cables are not wet. 10 4 Turn On/Off PM90 Turn On 1. Press and hold down the Power Key for a few seconds. 2. When PM90 enter to the boot mode, it will display SMART BEYOND RUGGED logo with short vibration. 3. Release the Power Key and wait until PM90 finish booting. Note: If you cannot turn on your PM90, try below steps:
- To turn on PM90, battery needs to be charged certain level. Please charge first.
- Press and hold the Power key for 12 seconds to force reboot. Turn Off 1. Press and hold the Power Key until you see the power menu. 2. Among the menu, tap Power off. 11 FCC warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help Caution: Any changes or modifications to this device not expressly approved by the party responsible for compliance could void your authority to operate the equipment. IC warning This device complies with Industry Canada license-exempt RSS standard(s).Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorisee aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radioelectrique subi, meme 12 si lebrouillage est susceptible den compromettre le fonctionnement. This device is restricted to indoor use only within the 5.15 ~ 5.35GHz Band. Cet appareil est restreint a l'utilisation a l'interieur seulement dans la bande 5.15
~ 5.35GHz. This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC/IC. Cet equipement est conforme aux limites d'exposition aux radiations FCC / IC definies pour un environnement non controle. Cet emetteur ne doit pas etre colocalise ou fonctionner en conjonction avec une autre antenne ou un autre emetteur, a moins d'etre autorise a le faire par le FCC / IC. E-label (FCC ID & IC, etc) Users can able to access the FCC/IC information in 3steps in devices menu. The actual steps are :
- Settings -> About phone -> Certificates WCDMA/LTE feature is optional Some product options only include WLAN feature. FCC ID IC ID WLAN PHONE V2X-PM90G V2X-PM90W 10664A-PM90G 10664A-PM90W 13