OWNERS MANUAL CAUTION:
To reduce the risk of fire or electric shock:
Do not mount or support cords or cables in a manner that can cut or damage wire insulation;
Use only the adapter provided with this product, and Make sure connectors are fully inserted and secured by fully fastening the connector rings. Specifications Input: AC 120V/60Hz, 2A (Max) Output: AC 120V/60Hz, 4x0.5A (Max) Model: PDR-026-120V USE & CARE Before using or reusing, inspect the product carefully. Discard any products that have cut, damaged or frayed wire insulation or cords, loose connections, or exposed copper wire. IMPORTANT:
Connect only standard LED lights without any functions. This product is equipped with an internal protection device (circuit breaker) that shuts off the power to an outlet when the outlet is overloaded. If lights with amperage over 0.5A are plugged to the outlet, the device will automatically switch off the outlet. Remove the lights and the outlet will work normally again. See TROUBLESHOOTING. 1. Connect your LED lights (not included) to one of the four outlets of the product. The actual number of lights to be connected to each outlet varies with the actual Rated Amperage of your lights. Please refer to the specifications and user manual of your lights. Do not exceed the maximum rated amperage or it may cause damage to the product and/or the user. IMPORTANT: Connect only standard LED lights without any functions. Plug 2. Plug the product to a wall or electrical outlet. Standard LED lights
(not included) 3. When not in use, unplug the product from power and store in a cool, dry place away from sunlight. 4. When storing the product, carefully remove the product from wherever it is placed, including trees, branches, or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires. TROUBLESHOOTING Lights of one (or more) of the outlets go off The outlet is overloaded. Unplug the power and wait for 30 minutes. Meanwhile check that the power output of your lights does not exceed 0.5Amp, the maximum capacity of each outlet. Replace with lights of less lighting load. Connect with only static, constant standard LED lights without any functions. Lights flash abnormally Remove your lights and replace with only static/constant LED lights without any functions or controller; the product should then work normally. 2 FUNCTIONS 1. Press to select from the 10 preset Shows in the following sequence:
Show#1: Steady Glow Show#2: Multi-speed Fading Show#3: Multi-speed Blinking Show#4: Chasing Show#5: Shooting Star Show#6: Stacking Show#7: Sparkle Show#8: Cross Wave Show#9: Alternating Show#10: Combo Press once after Show#10 to turn off the product.
* If you unplug and reconnect the product to power, the product will replay the last Show youve chosen. 2. Press to select from the 4 preset timer settings:
a. Setting 1: 4 hours ON and then 20 hours OFF (LED in Green) b. Setting 2: 6 hours ON and then 18 hours OFF (LED in Blue) c. Setting 3: 8 hours ON and then 16 hours OFF (LED in Red) d. Setting 4: OFF (LED in Yellow)
* The LED Timer Indicator of the product will constantly be on.
* The LED light on the remote control will blink 5 times in red before turning off. 3. The Timer will reset after each Show/Timer selection, and after you unplug and reconnect the product to power. MAINTENANCE Battery Cover Battery Replacement 1. To place/replace batteries, open the cover. 2. Insert two AAA-size batteries (not included) into the compartment. 3. Close the cover. WARNING:
Insert batteries with correct polarity (+/-). Use ONLY AAA size (LR03) batteries. For longer battery life, use alkaline batteries. WARNING: CHOKING HAZARD - AAA BATTERIES ARE SMALL PARTS, KEEP AWAY FROM CHILDREN. Do not expose light set to moisture. Do not mix old and new batteries. Do not mix alkaline, standard (Carbon - Zinc), lithium, or rechargeable
(NiCd, NiMH or other type) batteries. Remove batteries when not used for an extended period of time, or when depleted. Dispose of used batteries properly by following directions on batteries. Dry wipe with a cloth to clean the battery contacts prior to battery installation. DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES MAY EXPLODE OR LEAK. Fuse Replacement:
1. Grasp the plug and unplug the product from power. Do not unplug by pulling on the cord. 2. Slide open the fuse cover and remove the blown fuse carefully. 3. Insert the included spare fuse. Risk of fire: replace only with 10 Amp 125 Volt fuse provided with the product. 4. Slide close the fuse cover. OWNERS MANUAL LED LED Function Timer 2 x AAA batteries (not included) 10A SPARE FUSE 3