FCC ID: J9C-QCNFA524 Wi-Fi 6 + BT 5.1 M.2 1216 Module

FCC Radio Frequency (RF) Exposure Information This device has been evaluated to, and shown to be compliant with, the FCC Radio Frequency

(RF) exposure limits. Devices such as Desktop computers and Access Points (AP) that contain wireless functions (such as 802.11, Bluetooth, 3G or 4G) must be installed to provide a separation distance of at least 20cm from people to ensure compliance with the RF exposure requirements. Certain laptop/notebook computers, with antennas located toward the top of the screen, may require a separation distance of at least 20cm between the antennas and persons when they are operating to ensure compliance with the RF exposure requirements. These laptop/notebook computers are designed such that, during normal use with the screen open, the antenna-to-user distance is greater than 20cm. Some devices may have additional requirements for operating conditions to ensure compliance with RF exposure requirements. Specific instructions, where required, will be contained in the manual for that device. Please read your operating manual carefully. Interference Statement This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instruction manual, may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Notice: The FCC regulations provide that changes or modifications not expressly approved by Dell Inc. could void your authority to operate this equipment. These limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:

Reorient the receiving antenna. Relocate the system with respect to the receiver. Move the system away from the receiver. Plug the system into a different outlet so that the system and the receiver are on different branch circuits. If necessary, consult a representative of Dell Inc. or an experienced radio/television technician for additional suggestions. NOTE: Any additional Wireless module must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any other unauthorized installation or use will violate FCC Part 15 regulations. Modifications not expressly approved by Dell could void your authority to operate the equipment.

Quick Start

| | Dmarrage rapide | Quick Start Mulai Cepat | | | Incio rpido

Brzi poetak | Brzo pokretanje | Inicio rpido

Regulatory Model/Type

/ | / | Type/Modle rglementaire | Vorschriftenmodell/-Typ | Tipe/Model Resmi

/ | / | Tipo ou modelo de normalizao

/ | / | Regulatorni model/tip Regulatorni model/tip Modelo/tipo regulatorio

Informacin para NOM, o Norma Oficial Mexicana La informacin que se proporciona a continuacin se mostrar en los dispositivos que se describen en este documento, en conformidad con los requisitos de la Norma Oficial Mexicana (NOM):

Importador:

Dell Mxico, S.A. de C.V Av. Javier Barros Sierra, no 540, Piso 10, Col. Lomas de Santa Fe Delegacin lvaro Obregn, Ciudad de Mxico. C.P. 01219 R.F.C: DME9204099R6 Pas de origen: Hecho en China MCMC certification mark Windows In Windows Search, type System. In the search results, click System. Ubuntu On the desktop, click About This Computer. Di impor oleh:

PT Dell Indonesia Menara BCA Lantai 48 Unit 4804 Jalan M.H Thamrin No. 1 Jakarta Pusat, 10310 Indonesia Connection and use of this communications equipment is permitted by the Nigerian Communications Commission. Read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at Dell.com/regulatory_compliance. Dell.com/regulatory_compliance Regulatory Compliance Homepage () Dell.com/regulatory_compliance Lisez les consignes de scurit livres avec votre ordinateur. Pour des informations supplmentaires sur les pratiques d'excellence, reportez-vous la page d'accueil de la conformit aux rglementations sur Dell.com/regulatory_compliance. Weitere Informationen bieten die im Lieferumfang des Computers enthaltenen Sicherheitshinweise. Um zustzliche Informationen zur bestmglichen Einhaltung der Sicherheitsrichtlinien zu erhalten, sehen Sie die dazugehrige Homepage unter Dell.com/regulatory_compliance. Lihat informasi keselamatan yang disertakan dengan komputer Anda. Untuk informasi praktik keselamatan tambahan, kunjungi Laman Pemenuhan Peraturan di Dell.com/regulatory_compliance. Dell.com/regulatory_compliance

. , Dell.com/regulatory_compliance (Regulatory Compliance)

. Leia as informaes de segurana fornecidas com o seu computador. Para obter mais informaes sobre as boas prticas de segurana, consulte o site de conformidade normativa em Dell.com/regulatory_compliance.

- Dell.com/regulatory_compliance.

- Dell.com/regulatory_compliance. Proitajte bezbednosne informacije koje ste dobili uz raunar. Za dodatne informacije o najboljoj bezbednosnoj praksi pogledajte poetnu stranicu za usklaenost sa odredbama na adresi Dell.com/regulatory_compliance. Proitajte bezbednosne informacije koje ste dobili uz raunar. Za dodatne informacije o najboljim bezbednosnim praksama, pogledajte poetnu stranicu za usklaenost sa propisima na Dell.com/regulatory_compliance. Lea la informacin de seguridad enviada con el equipo. Para obtener informacin adicional sobre las mejores prcticas de seguridad, consulte la Pgina principal de conformidad reglamentaria en Dell.com/regulatory_compliance. Dell.com/regu latory_compliance Regulatory Compliances

. Dell.com/regulatory_compliance

. Do not remove the computer cover unless you need to install internal accessories for your computer. For instructions on removing and replacing parts, see the Owners or Service Manual at Dell.com/support. Dell.com/support Dell.com/support Ne retirez pas le capot de l'ordinateur moins que vous ne deviez installer des accessoires internes votre ordinateur. Pour obtenir des instructions sur le remplacement des pices, reportez-vous au Guide de l'utilisateur ou au Guide de maintenance l'adresse Dell.com/support. Entfernen Sie die Computerabdeckung nur dann, wenn Sie das interne Zubehr fr Ihren Computer einbauen mssen. Weitere Informationen zum Entfernen und Austauschen von Komponenten finden Sie im Benutzer- oder Service-Handbuch unter Dell.com/support. Jangan lepaskan penutup komputer kecuali Anda perlu memasang aksesori internal untuk komputer. Untuk petunjuk mengenai cara melepaskan dan memasang kembali komponen, lihat Panduan Layanan atau Panduan Pemilik di Dell.com/support. Dell.com/support

. Dell.com/support

. No remova a tampa do computador a no ser que queira instalar acessrios internos no computador. Para saber como remover e substituir peas, consulte o Manual de servio do proprietrio em Dell.com/support.

: Dell.com/support.

. " " " " - Dell.com/support. Nemojte uklanjati pokrov raunala osim ako ne trebate instalirati unutarnju dodatnu opremu za raunalo. Za upute o uklanjanju i zamijeni dijelova pogledajte Vlasniki ili Servisni prirunik na Dell.com/support. Ne skidajte poklopac raunara osim ako je potrebno da instalirate unutranji pribor na raunar. Za uputstva o uklanjanju i postavljanju delova pogledajte Uputstvo za upotrebu ili servis na adresi Dell.com/support. No extraiga la cubierta del equipo a menos que necesite instalar accesorios internos en el equipo. Para obtener instrucciones sobre cmo extraer y colocar piezas, consulte el Manual del propietario o el Manual de servicio en Dell.com/support. Dell.com/support

. Dell.com/support

. Retain the filler brackets or cards that ship with your computer. Installing filler brackets or filler cards over empty card-slot openings is necessary to maintain FCC certification of the computer. The filler brackets and filler cards keep dust and dirt out of your computer and maintain the airflow that cools your computer. FCC FCC Conservez les cartes de remplissage ou plaques de recouvrement livres avec votre ordinateur. L'installation des cartes de remplissage ou plaques de recouvrement sur les ouvertures vides de logement de carte est ncessaire pour maintenir la certification FCC de l'ordinateur. Les plaques de recouvrement et les cartes de remplissage permettent de protger votre ordinateur contre la poussire et la salet et de maintenir la circulation d'air servant refroidir votre ordinateur. Bewahren Sie die Abdeckbleche oder -Karten, die sich im Lieferumfang Ihres Computers befinden. Die Abdeckbleche oder -Karten mssen ber die leeren Steckplatzffnungen installiert werden, um die FCC-Zertifizierung des Computers zu erhalten. Die Abdeckbleche oder -Karten halten auch Staub und Schmutz vom Computer fern und helfen, die Khlung und den Luftstrom innerhalb des Computers aufrechtzuerhalten. Tahan braket pengisi atau kartu yang dikirimkan bersama komputer Anda. Braket pengisi atau kartu pengisi harus dipasang di celah slot kartu yang kosong untuk memenuhi sertifikasi FCC komputer. Braket pengisi dan kartu pengisi menjaga agar komputer Anda tidak terkena debu dan kotor serta mempertahankan aliran udara yang berfungsi untuk mendinginkan komputer. FCC

. FCC . Guarde as placas ou os dispositivos de preenchimento fornecidos com o seu computador. A instalao de placas ou dispositivos de preenchimento nas aberturas de slots de placas vazios necessria para manter a certificao da FCC (Federal Communications Commission (Comisso Federal de Comunicaes]) do seu computador. Os dispositivos de preenchimento mantm poeira e sujeira fora do computador e mantm o fluxo de ar que resfria o computador.

(FCC). - -

' ' ' (FCC). - -

' , '. Sauvajte umetke ili kartice koje ste dobili uz raunar. Stavljanje umetaka ili kartica u prazne otvore za kartice je neophodno za ouvanje FCC sertifikata raunara. Umeci i kartice spreavaju da praina i prljavtina prodre u raunar i odravaju protok vazduha kojim se raunar hladi. Zadrite konzole ili kartice za ispunu koje su isporuene sa raunarom. Instaliranje konzola za ispunu ili kartica za ispunu preko praznih leita za kartice je neophodno da bi se zadrao FCC sertifikat raunara. Konzole za ispunu i kartice za ispunu spreavaju da praina i prljavtina dospeju u va raunar i odravaju protok vazduha koji hladi va raunar. Conserve los cubrerranuras o las tarjetas que se envan con el equipo. Deben instalarse los cubrerranuras o las tarjetas de relleno en las aberturas vacas destinadas a tarjetas para conservar la certificacin FCC del equipo. Los cubrerranuras y las tarjetas de relleno evitan la entrada de polvo y suciedad en el equipo y mantienen el flujo de aire para refrigerar el equipo. FCC

. Power Adapter

| | Bloc d'alimentation | Netzteil | Adaptor Daya | | | Adaptador de alimentao

| | Adapter | Adapter za napajanje | Adaptador de alimentacin | |

Input voltage

| | Tension d'entre | Eingangsspannung | Tegangan input |

| Tenso de entrada | | | Ulazni napon | Ulazni napon Voltaje de entrada | |

Input current (maximum)

) | () | Courant d'entre (maximal) | Eingangsstrom (maximal) | Arus input (maksimal)

| () | Corrente de entrada (mxima) | ()

(.) | Ulazna struja (maksimalno) | Ulazna struja (maksimalna) Corriente de entrada (mxima) |

) Input frequency

| | Frquence d'entre | Eingangsfrequenz | Frekuensi input |

| Freqncia de entrada | | | Ulazna frekvencija Ulazna frekvencija | Frecuencia de entrada | |

Output current

| | Courant de sortie | Ausgangsstrom | Arus output |

| Corrente de sada | | | Izlazna struja | Izlazna struja Corriente de salida | |

Output voltage

| | Tension de sortie | Ausgangsspannung | Tegangan output |

| Tenso de sada | | | Izlazni napon | Izlazni napon Voltaje de salida | |

Maximum operating temperature

| | Temprature de fonctionnement maximale | Maximale Betriebstemperatur | Suhu operasi maksimum

| | Temperatura operacional mxima | |

| Maksimalna radna temperatura | Maksimalna radna temperatura | Temperatura de funcionamiento mxima |

Connect the power adapter or the power cable to your computer and to the display, if required. Branchez l'adaptateur secteur ou le cble d'alimentation votre ordinateur et l'cran, au besoin. Verbinden Sie den Netzadapter oder das Netzkabel mit dem Computer und Bildschirm, falls erforderlich. Hubungkan adaptor daya atau kabel daya pada komputer Anda serta pada display, jika diperlukan. Conecte o adaptador de alimentao ou o cabo de alimentao ao seu computador e tela, se necessrio.

' , , . Prikljuite adapter ili kabl za napajanje na raunar i na monitor, ako je to potrebno. Poveite adapter za napajanje ili kabl za napajanje sa raunarom i sa ekranom, ako je potrebno. Conecte el adaptador de alimentacin o el cable de alimentacin al equipo y a la pantalla, si es necesario.

, Power on the computer (and the display, if connected).

() Mettez l'ordinateur sous tension (et l'cran, s'il est branch). Schalten Sie den Computer (und den Bildschirm, falls angeschlossen) ein. Hidupkan komputer (serta display, jika tersambung).

( , ) . Ligue o computador (e a tela, se estiver conectada).

( , ). Ukljuite raunar (i monitor, ako je prikljuen). Ukljuite raunar (i ekran, ako je povezan). Encienda el equipo (y la pantalla, si est conectada).

) Depending on your computer configuration, some ports or connectors may not be available. En fonction de la configuration de votre ordinateur, certains ports ou connecteurs peuvent ne pas tre disponibles. Je nach Ihrer Computerkonfiguration knnen ggf. manche Ports oder Anschlsse nicht vorhanden sein. Tergantung pada konfigurasi komputer Anda, beberapa port mungkin tidak tersedia. Dependendo da configurao do seu computador, algumas portas ou alguns conectores podem no estar disponveis.

' . U zavisnosti od konfiguracije raunara, neki ulazi ili prikljuci nee biti dostupni. U zavisnosti od konfiguracije raunara neki portovi ili konektori moda nee biti dostupni. Segn la configuracin del equipo, algunos de los puertos y conectores pueden no estar disponibles.

, Icons

| | Icnes | Symbole | Ikon | | | cones | | | Ikone | Ikone | Iconos | |

Power adapter

| | Bloc d'alimentation | Netzteil | Adaptor daya |

| Adaptador de alimentao | | | Adapter | Adapter za napajanje Adaptador de alimentacin | |

USB 3.0/USB 3.1 with PowerShare PowerShare USB 3.1 | PowerShare USB | USB avec PowerShare | USB mit PowerShare | USB dengan PowerShare PowerShare USB | PowerShare USB | USB com PowerShare | USB PowerShare USB 3.0/USB 3.1 PowerShare | USB sa PowerShare-om/USB 3.0/USB 3.1 sa PowerShare funkcijom | USB con PowerShare PowerShare USB | PowerShare USB Thunderbolt 3 port with Power delivery (USB-C) Thunderbolt 3 Power Delivery (USB-C) | Thunderbolt 3 Power delivery (USB-C) Port Thunderbolt 3 avec Power delivery (USB-C) | Thunderbolt-3-Anschluss mit Stromversorgung (USB-C) Port Thunderbolt 3 dengan pengiriman Daya (USB-C) | Power Delivery (USB-C) Thunderbolt 3 3 (USB-C) | Porta Thunderbolt 3 com entrega de potncia (USB-C) Thunderbolt 3 (USB-C) | Thunderbolt 3 (USB-C) Thunderbolt 3 ulaz s napajanjem (USB-C) | Thunderbolt 3 port sa funkcijom napajanja (USB-C) | Puerto Thunderbolt 3 con Power Delivery (USB-C)

-C(

Thunderbolt 3 Thunderbolt 3

)USB

-C( |

USB USB 2.0 USB 3.0/USB 3.1 Gen 1 USB 3.1 Type-C eSATA Thunderbolt or or or or or or Icons

| | Icnes | Symbole | Ikon | | | cones | | | Ikone | Ikone | Iconos | |

Network

| | Cartes rseau | Netzwerk | Jaringan | | | rede | | | Mrea | Mrea | Red | |

VGA DVI HDMI DisplayPort Mini DisplayPort TV-in

| | TV-in | Entre TV | TV-Eingang | TV-in | TV | TV | Entrada de TV | TV-in | | Ulaz za TV | TV ulaz | Entrada de TV | |

External Graphics Port

| | Port graphique externe | Externer Grafikkartenanschluss | Port Grafik Eksternal | |

| Porta da placa grfica externa | | | Vanjski ulaz za grafiku karticu | Port za spoljanju grafiku | Puerto externo para grfica |

Infrared (IR) emitter

(IR) | (IR) | metteur infrarouge (IR) | Infrarot (IR)-Emitter | Emitor Inframerah (IR) | (IR)

(IR) | Emissor infravermelho (IR) | () | () | Infracrveni (IC) odailja Infracrveni (IC) emiter | Emisor de infrarrojos (IR) | (IR) | (IR)

Headphone/Audio-out

/ | / | Sortie audio/Casque | Kopfhrer/Audio-Ausgang | Headphone/Audio-out | /

/ | Fone de ouvido / Sada de udio | / | / | Audio izlaz/izlaz za slualice Slualica/Audio izlaz | Auricular/Salida de audio | / |

Headset

| / | Sortie audio/Casque | Headset/Audio-Ausgang | Headset/Audio-out | /

/ | Headset / Sada de udio | / | | Audio izlaz/izlaz za slualice s mikrofonom Slualice sa mikrofonom | Auricular con micro/Salida de audio | / |

HDMI Icons

| | Icnes | Symbole | Ikon | | | cones | | | Ikone | Ikone | Iconos | |

Microphone

| | Microphone | Mikrofon | Mikrofon |

| Microfone | | | Mikrofon | Mikrofon Micrfono | |

Line-in

| | Ligne d'entre | Leitungseingang | Line-in | | | Entrada de linha

| | Linijski ulaz | Linijski ulaz | Lnea de entrada | |

Line-out/Speakers: front left-right

/- | / | Ligne de sortie/Haut-parleurs : avant gauche-droit | Leitungsausgang/Kopfhrer: Vorderseite Links-Rechts | Line-out/Speaker: kiri-kanan depan | / | /: | Sada de linha / Alto-falantes:

direito e esquerdo dianteiros | /: - | /: -

Linijski izlaz/zvunici: napred levo-desno | Linijski izlaz/Zvunici: prednji levi-desni | Linea de salida/Altavoces: frontales izquierdo-derecho

Speakers: rear left-right

- | | Haut-parleurs : arrire gauche-droit | Lautsprecher: Rckseite Links-Rechts | Speaker: kiri-kanan belakang |

| : | Alto-falantes: direito e esquerdo traseiros | : - | : -

Zvunici: nazad levo-desno | Zvunici: zadnji levi-desni | Altavoces: posteriores izquierdo-derecho |

Speakers: side left-right

- | | Haut-parleurs : latral gauche-droit | Lautsprecher: Seite Links-Rechts | Speaker: samping kiri-kanan |

-| : | Alto-falantes: laterais esquerdo e direito | : - | : -

Zvunici: boni levi-desni | Zvunici: boni levi-desni | Altavoces: lateral izquierdo-derecho | / : |

Speakers: Audio center/subwoofer

/ | / | Haut-parleurs : Centre/caisson de basses audio | Lautsprecher: Audio Mitte/Subwoofer Speaker: Audio tengah/subwoofer | / | : / | Alto-falantes: udio central / subwoofer

: / | : / | Zvunici: audio centar/subvufer | Zvunici: Audio centar/niskotonac Altavoces: audio central/altavoz de tonos bajos |

or or or or or or S/PDIF Icons

| | Icnes | Symbole | Ikon | | | cones | | | Ikone | Ikone | Iconos | |

Screen-rotation lock

| | Verrouillage de rotation de l'cran | Bildschirmdrehungssperre | Kunci rotasi-layar

| | Travamento de rotao da tela | |

Blokada okretanja monitora | Blokada rotacije ekrana | Bloqueo de rotacin de pantalla | |

SIM-card slot SIM | SIM | Logement de carte SIM | SIM-Kartensteckplatz | slot kartu SIM | SIM SIM | Slot de carto SIM | SIM- | SIM- | Otvor za SIM-karticu | Slot za SIM karticu Ranura de tarjeta SIM | SIM

| SIM ExpressCard slot

| ExpressCard | Logement ExpressCard | ExpressCard-Steckplatz | Slot ExpressCard | ExpressCard ExpressCard | Slot ExpressCard | ExpressCard | ExpressCard | Otvor za karticu ExpressCard Slot za ExpressCard karticu | Ranura de ExpressCard | ExpressCard | ExpressCard Media-card reader

| Media-card | Lecteur de cartes multimedia | Kartenlesegert | Pembaca kartu media |

| Leitor de carto de mdia | |

ita memorijskih kartica | ita medijskih kartica | Lector de tarjetas multimedia |

Security-cable slot

| | Emplacement pour cble de scurit | Sicherheitskabeleinsteckplatz | Slot kabel pengaman |

| Encaixe do cabo de segurana | |

Otvor za bezbednosni kabl | Slot za zatitni kabl | Ranura del cable de seguridad | |

Power/Battery-status light

/ | / | Voyant d'tat de l'alimentation/la batterie | Anzeigeleuchte fr Betrieb/Akku | Lampu status daya/baterai

| / | / | Luz de status de alimentao

/ | / | Statusno svetlo napajanja/baterije Svetlo za status napajanja/baterije | Luz del estado de la batera/alimentacin | / |

Battery-status light

| | Voyant d'tat de la batterie | Akkustatusanzeige | Lampu status baterai |

| Luz de status da bateria | | /

Statusno svetlo baterije | Svetlo za status baterije | Luz del estado de la batera | |

Hard-drive activity light

| | Voyant d'activit du disque dur | Festplatten-Aktivittsleuchte | Lampu aktivitas hard drive

| | Luz de atividade do disco rgido

| | Indikator aktivnosti vrstog diska Svetlo za aktivnost vrstog diska | Luz de actividad de la unidad de disco duro | |

Icons

| | Icnes | Symbole | Ikon | | | cones | | | Ikone | Ikone | Iconos | |

Wi-Fi light Wi-Fi | Wi-Fi | Voyant Wi-Fi | Wi-Fi-Anzeigeleuchte | Lampu Wi-Fi | Wi-Fi | Wi-Fi | Luz do Wi-Fi Wi-Fi | Wi-Fi | Wi-Fi svetlo | Svetlo za Wi-Fi | Luz Wi-Fi | Wi-Fi | Wi-Fi Bluetooth light

| | Voyant Bluetooth | Bluetooth-Anzeigeleuchte | Lampu Bluetooth | Bluetooth | Bluetooth Luz do Bluetooth | Bluetooth | Bluetooth | Bluetooth svetlo | Svetlo za Bluetooth |

Luz Bluetooth | Bluetooth | Bluetooth

QCNFA524 Product name: Wi-Fi 6 + BT 5.1 M.2 1216 Module Revision History Revision Nov 2019 Description of Changes Initial Release Introduction The QCNFA524 module is designed to support Wi-Fi 6 and Bluetooth applications that support 2.4/5GHz, 2 streams 802.11a/b/g/n/ac/ax, and Bluetooth 5.1. The card uses the Microsoft Windows Client Utility (ACU) which is a user-mode utility designed to edit and add profiles for selected network interface adapters. This module requires professional installation and can be only assembled in a Microsoft Windows laptop/tablet by system manufacture. System Requirements Laptop/ PC containing:

32-bit PCI Express Bus 32 MB memory or greater 300 MHz processor or higher Microsoft Windows 10 Profile Management Configure the wireless network adapter (wireless card) from the Profile Management tab of the Client Utility. Add a profile Edit a profile Import a Profile Export a Profile Order profiles Switch to a different profile Remove a profile Connect to a Different Network The wireless network adapter works in either infrastructure mode (which uses an access point) or ad hoc mode (a group of stations participating in the wireless LAN). Create or Modify a Configuration Profile To add a new configuration profile, click New on the Profile Management tab. To modify a configuration profile, select the configuration from the Profile list and click the Modify button. The Profile Management dialog box displays the General tab. In profile management:

Edit the General tab. Edit the Security tab. Edit the Advanced tab. To configure a profile for ad hoc or access point (infrastructure) mode, edit the Network Type field on the Advanced tab. Note that the ACU only allows the creation of 16 configuration profiles. After the creation of 16 profiles, clicking the New button displays an error message. Remove an old profile or modify an existing profile for a new use. Remove a Configuration Profile 1. Go to the Profile Management tab. 2. Select the profile to remove from the list of configuration profiles. 3. Click the Remove button. Auto Profile Selection Management Including a profile in the auto selection feature allows the wireless adapter to automatically select that profile from the list of profiles and use it to connect to the network. Including a profile in auto profile selection:

1. On the Profile Management tab, click the Order Profiles button. 2. The Auto Profile Selection Management window appears, with a list of all created profiles in the Available Profiles box. 3. Highlight the profiles to add to auto profile selection, then click Add. The profiles appear in the Auto Selected Profiles box. Ordering the auto selected profiles:

1. Highlight a profile in the Auto Selected Profiles box. 2. Click Move Up, Move Down, or Remove as appropriate. The first profile in the Auto Selected Profiles box has highest priority, and the last profile has lowest priority. 3. Click OK. 4. Check the Auto Select Profiles box. 5. Save the modified configuration file. When auto profile selection is enabled by checking Auto Select Profiles on the Profile Management tab, the adapter scans for an available network. The profile with the highest priority and the same SSID as one of the found networks is the one that is used to connect to the network. If the connection fails, the adapter tries the next highest priority profile that matches the SSID, and so on. With auto profile selection enabled, the wireless adapter scans for available networks. The highest priority profile with the same SSID as a found network is used to connect to the network. On a failed connection, the adapter tries with the next highest priority profile. Switching to a Different Configuration Profile 1. To switch to a different profile, go to the Profile Management tab. 2. Click on the profile name in the Profile List. 3. Click the Activate button. The Profile List provides icons that specify the operational state for that profile. The list also provides icons that specify the signal strength for that profile. Import and Export Profiles Importing a Profile 1. From the Profile Management tab, click the Import button. The Import Profile window appears. 2. Browse to the directory where the profile is located. 3. Highlight the profile name. 4. Click Open. The imported profile appears in the profiles list. Exporting a Profile 1. From the Profile Management tab, highlight the profile to export. 2. Click the Export button. The Export Profile window appears. 3. Browse to the directory to export the profile to. 4. Click Save. The profile is exported to the specified location. Scan Available Networks Click the Scan button on the Profile Management tab to scan for available infrastructure and ad hoc networks. On this list, click Refresh to refresh the list at any time. Connecting to a different network Highlight a network name and click the Activate button to connect an available network. If no configuration profile exists for that network, the Profile Management window opens to the General tab. Fill in the profile name and click OK to create the configuration profile for that network. Tray Icon The tray icon appears at the bottom of the screen, and shows the signal strength using colors and the received signal strength indication (RSSI). Hold the mouse cursor over the tray icon to display the current configuration profile name and association, as well as transmit and receive speed and the wireless adapter name and IP address. Right-click on the tray icon to:

Help Open the online help. Open Client Utility Launch the Client Utility (ACU). Use the ACU to configure a profile or view status and statistics information. Troubleshooting Run the Troubleshooting Utility. Preferences Set the ACU startup and menu options. Check to start the program automatically when Windows starts, and check menu items that should appear on the popup menu. Enable/Disable Radio Enable or disable the RF signal. Manual LEAP Login Log in to LEAP manually, if LEAP is set to manually prompt for user name and password on each login. Reauthenticate Reauthenticate to the access point. Select Profile Click a configuration profile name to switch to. If no configuration profile exists for a connection, add a profile. Show Connection Status This window displays connection information:

Active Profile Displays the active configuration profile name. Auto Profile Selection Connection Status Shows whether auto profile selection is enabled. Displays whether the adapter is connected to a wireless network. Link Quality Lists the quality of the link connection. SSID Displays the SSID of the associated network. Access Point Shows the name of the AP the wireless adapter is Name connected to. Access Point Shows the IP address of the access point the IP Address wireless adapter is connected to. Lists the speed of the link connection. Displays the IP address of the wireless adapter. Link Speed Adapter IP Address Exit Exit the Client Utility application. The colors are defined as follows:

Color Green Green Yellow Red Gray Quality Excellent Good Poor Poor RSSI*

20 dB +

10-20 dB +

5-10 dB

< 5 dB No Connection No Connection

*Received signal strength indication RSSI. Displayed in dB or percentage. Enable or disable the tray icon in the Action menu. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module:

KDB 996369 D03 OEM Manual v01 rule sections:

2.2 List of applicable FCC rules This module has been tested for compliance to FCC Part 15 2.3 Summarize the specific operational use conditions The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as co-location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification. 2.4 Limited module procedures Not applicable. 2.5 Trace antenna designs Not applicable. 2.6 RF exposure considerations This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules. 2.7 Antennas The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users. 2 Approved antenna(s) list Antenna No. Brand Model Antenna Net gain Ant. Type Connector Type Cable Length

(mm) 1 WNC 81.EBJ15.005 PIFA i-pex(MHF2) 300 Cable Frequency Loss range

(dBi)

(GHz) 1.15 2.4~2.4835 1.70 5.15~5.35 5.47~5.725 1.74 5.725~5.850 1.79 2.4~2.4835 1.15 1.70 5.15~5.35 5.47~5.725 1.74 5.725~5.850 1.79 3.00 2.56 4.76 4.76 3.62 3.08 3.31 2.42 WNC 81.EBJ15.005 PIFA i-pex(MHF2) 300 2.8 Label and compliance information The final end product must be labeled in a visible area with the following: Contains FCC ID:

J9C-QCNFA524. The grantee's FCC ID can be used only when all FCC compliance requirements are met. 2.9 Information on test modes and additional testing requirements This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification. 2.10 Additional testing, Part 15 Subpart B disclaimer This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product

(including the transmitter) and obtaining a separate FCC authorization. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. OEM/Host manufacturer responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into any other device or system without retesting for compliance as multi-radio and combined equipment Industry Canada statement:

This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 20cm between the radiator & your body. Dclaration d'exposition aux radiations:

Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis plus de 20 cm entre le radiateur et votre corps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed and operated with greater than 20cm between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit tre install et exploit avec plus de 20 cm entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:

In the event that these conditions can not be met (for example certain laptop configurations or co-

location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:

Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed and operated with greater than 20cm between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC: 2723A-QCNFA524. Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un appareil o lantenne peut tre installe et utilise plus de 20 cm entre lantenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC: 2723A-QCNFA524". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. Caution :

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;

(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate;

(iv) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated. Avertissement:

Le guide dutilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment :

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) pour les dispositifs munis dantennes amovibles, le gain maximal dantenne permis pour les dispositifs utilisant les bandes de 5 250 5 350 MHz et de 5 470 5 725 MHz doit tre conforme la limite de la p.i.r.e;

(iii) pour les dispositifs munis dantennes amovibles, le gain maximal dantenne permis (pour les dispositifs utilisant la bande de 5 725 5 850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie, selon le cas;

(iv) lorsquil y a lieu, les types dantennes (sil y en a plusieurs), les numros de modle de lantenne et les pires angles dinclinaison ncessaires pour rester conforme lexigence de la p.i.r.e. applicable au masque dlvation, nonce la section 6.2.2.3, doivent tre clairement indiqus This radio transmitter (IC: 2723A-QCNFA524 / Model: QCNFA524) has been approved by ISED to operate with the antenna type listed below with maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (IC: 2723A-QCNFA524 / Model: QCNFA524) a t approuv par ISED pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Approved antenna(s) list Antenna No. Brand Model 1 WNC 81.EBJ15.005 Antenna Net gain 3.00 2.56 Frequency range

(GHz) 2.4~2.4835 5.15~5.35 Cable Loss

(dBi) 1.15 1.70 Ant. Type Connector Type Cable Length

(mm) PIFA i-pex(MHF2) 300 4.76 4.76 3.62 3.08 3.31 2.42 5.47~5.725 5.725~5.850 2.4~2.4835 5.15~5.35 5.47~5.725 5.725~5.850 1.74 1.79 1.15 1.70 1.74 1.79 2 WNC 81.EBJ15.005 PIFA i-pex(MHF2) 300 1. 2. 1. 2. XXXyyyLPDzzzz-x

WLAN label is sticked on the core side of D cover. Label QCNFA524 Contains FCC ID: J9C-QCNFA524 IC: 2723A-QCNFA524

Marking Specification 1) Marking process will be done on the metal shield cover. 2) The specification can be changed under customer request. Customer Model & Revision

- Model: 9D64T or NGK6Y

- Revision: X00,X01,X02,, A00,A01, 2D Barcode

- Customer Required Information(52digits) S/W option

- KILLER AX500-DBS or QCA6390 Module Model Name

- QCNFA524 Applicant Name

- QUALCOMM TECHNOLOGIES INC Antenna Info.

- MAIN, AUX Certification ID (T.B.D)

- FCC ID: J9C-QCNFA524

- IC:2723A-QCNFA524

- IFT NO.XXXXXXXXX-XXXX

- ANATEL:XXXX-XX-XXXX

- CMIIT ID:XXXXXXXXXX(M) 9D64T X02 KILLER AX500-DBS QCNFA524 QUALCOMM TECHNOLOGIES INC FCC ID:J9C-QCNFA524 IC:2723A-QCNFA524 IFT NO.XXXXXXXXX-XXXX ANATEL:XXXX-XX-XXXX CMIIT ID:XXXXXXXXXX(M) A T 1 0 1 0 1 A 5 1 A J Module Serial Number

- S/N(12digits) 2/5 AUXMAIN

Qualcomm Technologies, Inc. 5775 Morehouse Drive, San Diego, CA 92121-1714 www.qualcomm.com 11 March 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Ref: FCC Class II Permissive change for FCC ID: J9C-QCNFA524 (Original Grant date: 11/20/2019) Dear Examiner, This is to request a Class II permissive change for Wi-Fi 6 + BT 5.1 M.2 1216 Module, Model Name:

QCNFA524, FCC ID: J9C-QCNFA524. The major change filed under this application is:

The subject approved module is being used in a specific host (portable category configuration, brand name/model: see test report). Also please note the following with respect to this application:

Software security remains unchanged from the original filing SAR testing is performed to demonstrate compliance. Power reduction is required to this host to comply SAR requirement. If you have any questions regarding this application, please feel free to contact me. Best Regards Stanley Lin Qualcomm Technologies Inc.

Qualcomm Technologies, Inc. 5775 Morehouse Drive, San Diego, CA 92121-1714 www.qualcomm.com 9 April 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject:

FCC ID:

To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Request for Confidentiality J9C-QCNFA524 Antenna Specification Tune-up Procedure Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until June 10, 2020. Test Setup Photos Internal Photos External Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and that information will be available for public review once the grant of equipment authorization is issued. Best Regards Stanley Lin Qualcomm Technologies, Inc.

Qualcomm Technologies, Inc. 5775 Morehouse Drive, San Diego, CA 92121-1714 www.qualcomm.com 11 March 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Re: Class II Permissive Change, QCNFA524 (FCC ID: J9C-QCNFA524) hosted in DELL computer model P92F To whom it may concern:

I, the undersigned, hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch to act on our behalf in all manners relating to application for equipment authorization of QCNFA524

(FCC ID: J9C-QCNFA524) hosted in DELL computer model P92F 1. Receiving and exchanging data for the purposes of obtaining Type Approval certificates for model QCNFA524 (FCC ID: J9C-QCNFA524) 2. Such authorization includes and is limited to preparing and submitting applications and corresponding documentation and information for certification of model QCNFA524 (FCC ID: J9C-

QCNFA524) This authorization expires 1 year past the date indicated at the top of this letter. This authorization supersedes all previous authorizations provided by the undersigned. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). comply with the relevant provisions of the certification program;

In authorizing Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch as our representative, we still recognize that we are responsible to:

a) b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

c) make claims regarding certification only in respect of the scope for which certification has been granted;

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

use certification only to indicate the products are certified as being in conformity with specified standards;

endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

document the actions taken. k) This authorization is valid until further written notice from the applicant. e) f) g) h) i) j) Best Regards Stanley Lin Qualcomm Technologies Inc.

Qualcomm Technologies, Inc. 5775 Morehouse Drive, San Diego, CA 92121-1714 www.qualcomm.com November 13, 2019 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Authorization of Handling FCC Regulatory Applications FCC Identifier J9C To Whom It May Concern:

I, hereby, authorize Mr. Stanley Lin, to handle FCC Regulatory related applications for Qualcomm Technologies, Inc. FCC Identifier J9C and sign all required application documents. Best Regards, Paul Guckian VP, Engineering Qualcomm Technologies, Inc. 5775 Morehouse Drive San Diego, CA 92121 Office: 858-651-1547 pguckian@qti.qualcomm.com

QualcommTechnologies,Inc. 5775MorehouseDrive,SanDiego,CA92121 1714 19 November 2019 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject:

FCC ID:

To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Request for Confidentiality J9C-QCNFA524

Schematics Diagram

Block Diagram

Theory of Operation

Integrator Instruction

Antenna Specification

Software Security Statement

Tune up letter Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days.

External photos

Test Setup photos

Users manual

Internal Photos It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and that information will be available for public review once the grant of equipment authorization is issued. Best Regards Stanley Lin Qualcomm Technologies, Inc.

QualcommTechnologies,Inc. 5775MorehouseDrive,SanDiego,CA92121 1714 15 November 2019 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. To whom it may concern:

I, the undersigned, hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch to act on our behalf in all manners relating to application for equipment authorization of J9C-

QCNFA524 1. Receiving and exchanging data for the purposes of obtaining FCC grant for model FCC ID:J9C-

QCNFA524 under this permissive change application. 2. Such authorization includes and is limited to preparing and submitting applications and corresponding documentation and information for certification of model FCC ID:J9C-QCNFA524 This authorization expires 1 year past the date indicated at the top of this letter. This authorization supersedes all previous authorizations provided by the undersigned. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). comply with the relevant provisions of the certification program;

In authorizing Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch. as our representative, we still recognize that we are responsible to:

a) b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

c) make claims regarding certification only in respect of the scope for which certification has been granted;

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) f) g) h) i) j) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

use certification only to indicate the products are certified as being in conformity with specified standards;

endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

document the actions taken. k) This authorization is valid until further written notice from the applicant. Best Regards Stanley Lin Qualcomm Technologies, Inc.

FCC ID: J9C-QCNFA524 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch November 19, 2019 Dear Application Examiner, Qualcomm Technologies, Inc., Gigabit RF Card, FCC ID: J9C-QCNFA524 would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of KDB 996369 have been met and shown on the following statements. 1. The modular transmitter must have its own RF shielding. The radio portion of this module has been shielded, please see exhibition External Photo. 2. The modular transmitter must have buffered modulation/data inputs. The EUT has buffered data inputs, it is integrated in chip QCA6390. 3. The modular transmitter must have its own power supply regulation. The part number of this regulator is QCA6390. 4. The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C). The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. The modular transmitter must be tested in a stand-alone configuration The EUT was tested in a stand-alone configuration via an ExpressCard connector. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. The modular transmitter must be labeled with its own FCC ID number. Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: J9C-QCNFA524 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. The modular transmitter must comply with any applicable RF exposure requirements. The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Regards, Andrea Hsia Supervisor Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Tel: 886-3-318 3232 ext. 1628 Fax: 886-3-327 0892 Email: andrea.hsia@tw.bureauveritas.com