ZK601 Hardware Specification ZK601 Hardware Specifications GSM/GPRS/LTE CAT.M1&NB1 GPS Intelligent Terminal Version: 1.00 ZK601 Hardware Specification Document Title ZK601 Hardware Specification Version Author Date 1.00 Xin Yang 2019-08-05 Note 1: T-Panel 201 is Model Name for sales. ZK601 is a model name for T-Panel 201 in company inside. Note 2: This manual is a Worldwide version. The operation frequency band of the product will be different for different countries.Details please consult Queclink. ZK601 Hardware Specification Contents 0. Revision History ............................................................................................................... 1 1. Introduction .................................................................................................................... 2 2. Special Note .................................................................................................................... 2 3. Basic Specification ............................................................................................................ 2 4. Hardware Description ....................................................................................................... 3 4.1. Hardware Block Diagram .......................................................................................... 3 4.2. Internet RF Specification .......................................................................................... 3 4.2.1. ZK601 (GSM&GPRS) RF specification ....................................................... 3 4.2.2. ZK601 (LTE CAT.M1&CAT.NB1) RF specification ....................................... 4 4.3. GPS Specification ..................................................................................................... 4 4.4. BLE Specification ..................................................................................................... 5 4.5. NFC Specification .................................................................................................... 5 4.6. Other Parameters .................................................................................................... 5 5. Hardware Interface Description ......................................................................................... 6 5.1. ECU Interface .......................................................................................................... 6 5.2. Debug Interface ...................................................................................................... 6 5.3. Dual Brake Interface ................................................................................................ 7 5.4. Accelerator Interface ............................................................................................... 7 5.5. Front Light Interface ................................................................................................ 7 5.6. LED Display ............................................................................................................. 8 5.7. Audio Codec ........................................................................................................... 8 5.8. Battery Charging Management ................................................................................. 8 6. User Guide ...................................................................................................................... 9 6.1. Guiding .................................................................................................................. 9 ZK601 Hardware Specification 0. Revision History Version Date Author Description of Change 1.00 2019-08-05 Xin Yang Initial Version 1 ZK601 Hardware Specification 1. Introduction ZK601 software function development mainly involves electric control unit (ECU), @Track Air Protocol, instrument display, headlight control, acceleration, brake, key on panel, voice broadcast and Bluetooth. ZK601 device is designed to connect to the scooter to enable remotely lock/unlock, to track the position information and to report the status of the scooter. By using the accelerator or brake, the user can increase or decrease the speed of the scooter. By using the key on the panel, the user can turn on the headlight, switchover the speed-up mode or end using the scooter. All the information will be reported to the backend sever to facilitate the basic functions of the scooter. 2. Special Note LoT must be powered on again by pressing power button or charging if it is powered down unexpectedly. 3. Basic Specification Item Dimension Input Power Specification Length*Width*Height: 149mm*47mm*51mm DC: 36V5V( withstand 60V for less than 2 seconds) Backup Battery Li-Polymer, 750mAh IP Grade IP67 Operating Temperature
-20 ~ +60 Power Consumption Active: 36V@ 21mA Sleep: 36V@ 5mA Shut-down: 36V@ 100uA 2 ZK601 Hardware Specification 4. Hardware Description 4.1. Hardware Block Diagram Following is the Hardware Block Diagram of ZK601:
4.2. Internet RF Specification The ZK601 supports GSM/GPRS/EDGE/ LTE CAT-M1/ CAT-NB1 for selection. 4.2.1. ZK601 (GSM&GPRS) RF specification Item ZK601 (GSM&GPRS) RF specification Applicable Region Worldwide Technology GSM&GPRS&EDGE GSM:
Operation Band US:GSM850/ PCS1900 EU: EGSM900/ DCS1800 GPRS:
Support GPRS multi-slot class 33 Max 107kbps (DL)/Max 85.6kbps (UL) EDGE:
Support EDGE multi-slot class 33 Max 296kbps (DL)/Max 236.8kbps (UL) CSD:
GSM/GPRS/EDGE Features CSD transmission rates: 14.4kbps non-transparent RF Output Power Class 4 (33dBm2dB) for GSM850 and EGSM900 3 ZK601 Hardware Specification Class 1 (30dBm2dB) for DCS1800 and PCS1900 Class E2 (27dBm3dB) for GSM850 and EGSM900 8-PSK Class E2 (26dBm3dB) for DCS1800 and PCS1900 8-PSK Receive Sensitivity GSM850: -109.5dBm (typ.) EGSM900: -108.5dBm (typ.) DCS1800: -110dBm (typ.) PCSM1900: -108dBm (typ.) Transmit Mode TCP Antenna Internal only 4.2.2. ZK601 (LTE CAT.M1&CAT.NB1) RF specification Item ZK601 (LTE CAT.M1&CAT.NB1) RF Specification Applicable Region Worldwide Technology LTE CAT.M1&CAT.NB1:
LTE-FDD:
Operation Band US: B2/B4/B5/B12/B13/B/B25 EU: B1/B3/B8/B20/B28 Support LTE Cat.M1 and LTE Cat.NB1 LTE Features Cat.M1: Max. 375kbps (DL)/375kbps (UL) Cat.NB1: Max. 32kbps (DL)/70kbps (UL) RF Output Power LTE-FDD: 23dBm2.7dB Receive Sensitivity LTE-FDD: -107 dBm (typ.) for CAT.M1, -117 dBm (typ.) for CAT.NB1 Transmit Mode TCP Antenna Internal only 4.3. GPS Specification Item GPS Chipset Receive Type Receive Sensitivity
(GPS+GLONASS) Position Accuracy (CEP) TTFF(Open Sky/GPS+GLONASS) Antenna GPS Specification U-blox M8 u-blox All-In-One GPS receiver Tracking & Navigation: -167 dBm Reacquisition: -160 dBm Cold Start: -148 dBm Hot Start: -157 dBm GPS<2.5m GPS+GLONASS<2.5m BEIDOU<3m GLONASS<4m Could Start: 26S average Hot Start: < 1s Internal only 4 ZK601 Hardware Specification 4.4. BLE Specification Full Bluetooth 4.1 or higher integration from ST. The minimum communication distance is 15 meters regardless of device orientation. Item Frequency BLE Specification 2.4GHz RF transceiver compatible with Bluetooth low energy
(BLE) Receive Sensitivity
-88dBm RF Output Power Up to 10dBm Antenna Internal only 4.5. NFC Specification Item Frequency Read Range NFC Specification Contactless communication at 13.56MHz
<2cm Support Protocol ISO/IEC 15693 Antenna Internal only 4.6. Other Parameters Item MCU G-Sensor Audio Codec Specification STM32F411RET6:
Core: Cortex M4 Flash memory: 512K bytes Ram: 128k bytes Frequency: Up to 100Mhz Mode Type: 3D accelerometer Acceleration Range: 2/4/8/16g I2S/PCM serial port 24-bit, 8 to 96 kHz sampling frequency 95 dB signal to noise ratio 1.25W@8/5V or 1.8W@4/4.2V mono class D speaker driver 5 ZK601 Hardware Specification 5. Hardware Interface Description 5.1. ECU Interface Power Input:
Wide range input: 36V5V DC Short-circuit protection Soft-start timer Smart Power Management UART Interface:
Baud rate auto adaption, support 9600bps, 19200bps,115200bps 3.3V and 5V TTL level compatible Power Control Wire To activate ECU OD drain output, compatible with external pull-up voltage 3V-36V 5.2. Debug Interface Main Features:
For purpose of configuration/firmware upgrade of MCU 3.3V and 5V TTL level compatible 6 ZK601 Hardware Specification 5.3. Dual Brake Interface Main Features:
The power 5V for the brake HALL sensor is controllable HALL output voltage 1-4V, sensitivity: 1.2mV/G 5.4. Accelerator Interface Main Feature:
The power 5V for the brake HALL sensor is controllable HALL output voltage 1-4V, sensitivity: 1.2mV/G 5.5. Front Light Interface Main Feature:
Drives LED strings up to 12V Switch current limit: 0.4A PWM dimming frequency: 20KHz~1MHz (this function is reserved) 7 ZK601 Hardware Specification 5.6. LED Display Drive LED SEG up to 50mA@5V, Drive up LED GRID to 200 mA@5V Display mode: 8seg*6dig Refresh Rate: 450KHz 5.7. Audio Codec Main Feature:
High performance and low power multibit delta-sigma audio ADC and DAC I 2S/PCM master or slave serial data port 24-bit, 8 to 96 kHz sampling frequency Signal to noise ratio: 95 dB, THD+N: -85 dB 1.25W@8/5V or 1.8W@4/4.2V mono class D speaker driver 5.8. Battery Charging Management Main Feature:
Integrated dynamic power path management Supports up to 0.3A charge current Supports short-circuit and chip thermal protection Support battery temperature detection during charging Status indication - Charging/Done 8 ZK601 Hardware Specification 6. User Guide 6.1. Guiding 1. Connect ZK601 to Scooter with 5 Pin Serial port Cable. 2. To charge Scooter to activate ZK601. 3. ZK601 uploads the GPS data or the status of Scooter to Server. 4. ZK601 receives command from Server to control Scooter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 9 ZK601 Hardware Specification This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente
(p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. ce matriel est conforme aux limites de dose d'exposition aux rayonnements, CNR-102 nonce dans un autre environnement.cette eqipment devrait tre install et exploit avec distance minimale de 20 entre le radiateur et votre corps. RF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. 10