| submitted | available | document details (if available) | source link |
|---|---|---|---|
| various | Test Report | Test Report | 995.28 KiB |
FCC Radio Test Report FCC ID: RWO-RZ030188 This report concerns (check one): Original Grant Class II Change Project No. Equipment Model Name Applicant Address
: 1603C186
: Wireless Keyboard
: RZ03-0188
: Razer Inc.
: 201 3rd Street, Suite 900, San Francisco,CA 94103 Date of Receipt Date of Test Issued Date Tested by
: Mar. 16, 2016
: Mar. 16, 2016 ~ Apr. 19, 2016
: Apr. 20, 2016
: BTL Inc. Testing Engineer Technical Manager Authorized Signatory
:
:
:
(Shawn Xiao)
(David Mao)
(Steven Lu) B T L I N C . No.3, Jinshagang 1st Road, Shixia, Dalang Town, Dongguan, TEL: +86-769-8318-3000 FAX: +86-769-8319-6000 Guangdong, China. Report No.: BTL-FCCP-1-1603C186 Page 1 of 61 Declaration BTL represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with standards traceable to international standard(s) and/or national standard(s). BTL's reports apply only to the specific samples tested under conditions. It is manufactures responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. BTL shall have no liability for any declarations, inferences or generalizations drawn by the client or others from BTL issued reports. BTLs report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and BTL-self, extracts from the test report shall not be reproduced except in full with BTLs authorized written approval. and accredited by the conformity assessment authorities listed in this test report. BTLs laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Report No.: BTL-FCCP-1-1603C186 Page 2 of 61 Table of Contents Page 4 . EMC EMISSION TEST 3 . GENERAL INFORMATION 1 . CERTIFICATION 2 . SUMMARY OF TEST RESULTS 4.1 CONDUCTED EMISSION MEASUREMENT 2.1 TEST FACILITY 2.2 MEASUREMENT UNCERTAINTY 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 4.1.2 TEST PROCEDURE 4.1.3 DEVIATION FROM TEST STANDARD 4.1.4 TEST SETUP 4.1.5 EUT OPERATING CONDITIONS 4.1.6 EUT TEST CONDITIONS 4.1.7 TEST RESULTS 6 7 8 8 9 9 3.1 GENERAL DESCRIPTION OF EUT 11 3.2 DESCRIPTION OF TEST MODES 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 11 3.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 12 3.5 DESCRIPTION OF SUPPORT UNITS 12 13 13 13 13 13 14 14 14 14 15 15 16 16 17 18 18 18 19 19 20 20 20 20 20 20 20 20 4.2.1 RADIATED EMISSION LIMITS 4.2.2 TEST PROCEDURE 4.2.3 DEVIATION FROM TEST STANDARD 4.2.4 TEST SETUP 4.2.5 EUT OPERATING CONDITIONS 4.2.6 EUT TEST CONDITIONS 4.2.7 TEST RESULTS (9KHZ TO 30MHZ) 4.2.8 TEST RESULTS (30MHZ TO 1000 MHZ) 4.2.9 TEST RESULTS (ABOVE 1000 MHZ) 5.1.1 TEST PROCEDURE 5.1.2 DEVIATION FROM STANDARD 5.1.3 TEST SETUP 5.1.4 EUT OPERATION CONDITIONS 5.1.5 EUT TEST CONDITIONS 5.1.6 TEST RESULTS 4.2 RADIATED EMISSION MEASUREMENT 5.1 APPLIED PROCEDURES / LIMIT 5 . BANDWIDTH TEST Report No.: BTL-FCCP-1-1603C186 Page 3 of 61 Table of Contents Page 6 . MAXIMUM OUTPUT POWER TEST 6.1 APPLIED PROCEDURES / LIMIT 6.1.1 TEST PROCEDURE 6.1.2 DEVIATION FROM STANDARD 6.1.3 TEST SETUP 6.1.4 EUT OPERATION CONDITIONS 6.1.5 EUT TEST CONDITIONS 6.1.6 TEST RESULTS 7 . ANTENNA CONDUCTED SPURIOUS EMISSION 7.1 APPLIED PROCEDURES / LIMIT 7.1.1 TEST PROCEDURE 7.1.2 DEVIATION FROM STANDARD 7.1.3 TEST SETUP 7.1.4 EUT OPERATION CONDITIONS 7.1.5 EUT OPERATION CONDITIONS 7.1.6 TEST RESULTS 8 . POWER SPECTRAL DENSITY TEST 8.1 APPLIED PROCEDURES / LIMIT 8.1.1 TEST PROCEDURE 8.1.2 DEVIATION FROM STANDARD 8.1.3 TEST SETUP 8.1.4 EUT OPERATION CONDITIONS 8.1.5 EUT TEST CONDITIONS 8.1.6 TEST RESULTS 9 . MEASUREMENT INSTRUMENTS LIST ATTACHMENT A - CONDUCTED EMISSION ATTACHMENT B - RADIATED EMISSION (9KHZ TO 30MHZ) ATTACHMENT C - RADIATED EMISSION (30MHZ TO 1000MHZ) ATTACHMENT D - RADIATED EMISSION (ABOVE 1000MHZ) ATTACHMENT E - BANDWIDTH ATTACHMENT F - MAXIMUM OUTPUT POWER TEST ATTACHMENT G - ANTENNA CONDUCTED SPURIOUS EMISSION ATTACHMENT H - POWER SPECTRAL DENSITY TEST 21 21 21 21 21 21 21 21 22 22 22 22 22 22 22 22 23 23 23 23 23 23 23 23 24 26 29 31 38 51 54 55 59 Report No.: BTL-FCCP-1-1603C186 Page 4 of 61 Issued No. BTL-FCCP-1-1603C186 REPORT ISSUED HISTORY Description Original Issue. Issued Date Apr. 20, 2016 Report No.: BTL-FCCP-1-1603C186 Page 5 of 61
: Wireless Keyboard
: 514 Chai Chee Lane #07-01 ~ 06 Singapore 469029, Tel: +65 6505 2188
: RAZER TECHNOLOGY AND DEVELOPMENT (SHENZHEN) CO., LTD
: East Wing, 3rd Floor, Block 2, Phase 1 of Vision Shenzhen Business Park Keji 1. CERTIFICATION Equipment Brand Name : RAZER Model Name : RZ03-0188 Applicant
: Razer Inc. Manufacturer : Razer (Asia-Pacific) Pte.,Ltd. Address Factory Address Date of Test Test Sample : Engineering Sample Standard(s) The above equipment has been tested and found compliance with the requirement of the relative standards by BTL Inc. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. BTL-FCCP-1-1603C186) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of TAF according to the ISO-17025 quality assessment standard and technical standard(s). South Road, Hi-Tech Industrial Park, Shenzhen 518057, China
: FCC Part15, Subpart C (15.247) / ANSI C63.10-2013
: Mar. 16, 2016 ~ Apr. 19, 2016 Report No.: BTL-FCCP-1-1603C186 Page 6 of 61 2. SUMMARY OF TEST RESULTS Test procedures according to the technical standard(s):
Applied Standard(s): FCC Part15 (15.247) , Subpart C Standard(s) Section 15.207 15.247(d) 15.247(a)(2) 15.247(b)(3) 15.247(e) 15.203 Test Item Conducted Emission Antenna conducted Spurious Emission 6dB Bandwidth Peak Output Power Power Spectral Density Antenna Requirement 15.209/15.205 Transmitter Radiated Emissions RSS-247 5.5 Band Edge Emissions NOTE:
(1) N/A denotes test is not applicable to this device. Judgment Remark PASS PASS PASS PASS PASS PASS PASS PASS Report No.: BTL-FCCP-1-1603C186 Page 7 of 61 2.1 TEST FACILITY The test facilities used to collect the test data in this report is at the location of No.3, Jinshagang 1st Road, Shixia, Dalang Town, Dongguan, Guangdong, China. BTL's test firm number for FCC: 319330 2.2 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2. The BTL measurement uncertainty is less than the CISPR 16-4-2 Ucispr requirement. The reported uncertainty of measurement y U, where expanded uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. A. Conducted Measurement:
Test Site Method Measurement Frequency Range DG-C02 CISPR 150 KHz ~ 30MHz U, (dB) 2.32 B. Radiated Measurement:
Test Site Method Measurement Frequency DG-CB03 CISPR Range 9KHz~30MHz 9KHz~30MHz 30MHz ~ 200MHz 30MHz ~ 200MHz 200MHz ~ 1,000MHz 200MHz ~ 1,000MHz 1GHz~18GHz 1GHz~18GHz 18GHz~40GHz 18GHz~40GHz Ant. H / V U, (dB) V 3.79 3.57 H 3.82 V H 3.78 4.10 V 4.06 H 3.12 V H 3.68 4.15 V H 4.14 Note: Unless specifically mentioned, the uncertainty of measurement has not been taken into account to declare the compliance or non-compliance to the specification. Report No.: BTL-FCCP-1-1603C186 Page 8 of 61 3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT Equipment Brand Name Model Name Model Difference Product Description Power Source Power Rating Wireless Keyboard RAZER RZ03-0188 N/A Operation Frequency 2402~2480 MHz GFSK(1Mbps) Modulation Technology Bit Rate of Transmitter Output Power (Max.) 1# Battery supplied. 2# Supplied from USB port. 3# DC Voltage supplied from AC/DC adapter (support unit). 1# DC 3.7V 2# DC 5V 1.5A 3# DC 5V 2A 0.22dBm (1Mbps) Note:
1. For a more detailed features description, please refer to the manufacturers specifications or the user's manual. Report No.: BTL-FCCP-1-1603C186 Page 9 of 61 2. Channel List:
Channel 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 Frequency
(MHz) 2402 2404 2406 2408 2410 2412 2414 2416 2418 2420 2422 2424 2426 2428 2430 2432 2434 2436 2438 2440 Channel 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 Frequency
(MHz) 2442 2444 2446 2448 2450 2452 2454 2456 2458 2460 2462 2464 2466 2468 2470 2472 2474 2476 2478 2480 3. Table for Filed Antenna:
Ant. 1 Brand N/A Model Name Antenna Type Connector Gain (dBi) N/A Printed N/A 2.22 Report No.: BTL-FCCP-1-1603C186 Page 10 of 61 3.2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Mode 1 Description TX Mode NOTE (1) The EUT system operated these modes were found to be the worst case during the pre-scanning test as following:
Final Test Mode Mode 1 Final Test Mode Mode 1 For Conducted Test Description TX Mode For Radiated Test Description TX Mode NOTE (1) Note:
(1) The measurements are performed at the high, middle, low available channels. 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING During testing channel & power controlling software provided by the customer was used to control the operating channel as well as the output power level. The RF output power selection is for the setting of RF output power expected by the customer and is going to be fixed on the firmware of the final end product power parameters of WLAN Test Software Version Frequency (MHz) BT LE N/A 2440 N/A 2480 N/A 2402 N/A Report No.: BTL-FCCP-1-1603C186 Page 11 of 61 3.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 3.5 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Mfr/Brand Model/Type No. A RAZER KSA29B0500200D5 Adapter Item Shielded Type Ferrite Core 1 YES NO Length 1.8m FCC ID N/A Series No. N/A Note USB cable For detachable type I/O cable should be specified the length in m inLengthcolumn. Note:
(1) Report No.: BTL-FCCP-1-1603C186 Page 12 of 61 4. EMC EMISSION TEST 4.1 CONDUCTED EMISSION MEASUREMENT 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS (Frequency Range 150KHz-30MHz) Frequency of Emission (MHz) 0.15 -0.5 0.50 -5.0 5.0 -30.0 Note:
Conducted Limit (dBV) Quasi-peak 66 to 56*
56 60 Average 56 to 46*
46 50
(1) The limit of " * " decreases with the logarithm of the frequency
(2) The test result calculated as following:
Measurement Value = Reading Level + Correct Factor Correct Factor = Insertion Loss + Cable Loss + Attenuator Factor(if use) Margin Level = Measurement Value - Limit Value The following table is the setting of the receiver Receiver Parameters Attenuation Start Frequency Stop Frequency IF Bandwidth Setting 10 dB 0.15 MHz 30 MHz 9 kHz 4.1.2 TEST PROCEDURE a. The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the and forth in the center forming a bundle 30 to 40 cm long. cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d. LISN at least 80 cm from nearest part of EUT chassis. e. For the actual test configuration, please refer to the related Item EUT Test Photos. 4.1.3 DEVIATION FROM TEST STANDARD No deviation Report No.: BTL-FCCP-1-1603C186 Page 13 of 61 4.1.4 TEST SETUP Ve rtic a l R e fe re n c e G ro u n d P la n e Te s t R e c e iv e r 4 0 c m E U T L IS N 8 0 c m H o riz o n ta l R e fe re n c e G ro u n d P la n e N o te : 1 .S u p p o rt u n its w e re c o n n e c te d to s e c o n d L IS N . 2 .B o th o f L IS N s ( A M N ) a re 8 0 c m fro m E U T a n d a t le a s t 8 0 fro m o th e r u n its a n d o th e r m e ta l p la n e s 4.1.5 EUT OPERATING CONDITIONS The EUT was configured for testing in a typical fashion (as a customer would normally use it). The EUT has been programmed to continuously transmit during test. This operating condition was tested and used to collect the included data. 4.1.6 EUT TEST CONDITIONS Temperature: 24C Relative Humidity: 60% Test Voltage: AC 120V/60Hz 4.1.7 TEST RESULTS Please refer to the Attachment A. Remark:
(1) All readings are QP Mode value unless otherwise stated AVG in column ofNote. If the QP Mode Measured value compliance with the QP Limits and lower than AVG Limits, the EUT shall be deemed to meet both QP & AVG Limits and then only QP Mode was measured, but AVG Mode didnt perform.In this case, a * marked in AVG Mode column of Interference Voltage Measured.
(2) Measuring frequency range from 150KHz to 30MHz.
(3) N/A denotes test is not applicable to this device. Report No.: BTL-FCCP-1-1603C186 Page 14 of 61 4.2 RADIATED EMISSION MEASUREMENT 4.2.1 RADIATED EMISSION LIMITS In case the emission fall within the restricted band specified on 15.205(a), then the 15.209(a) limit in the table below has to be followed. LIMITS OF RADIATED EMISSION MEASUREMENT (9KHz-1000MHz) Frequency
(MHz) 0.009~0.490 0.490~1.705 1.705~30.0 30~88 88~216 216~960 960~1000 Field Strength
(microvolts/meter) 2400/F(KHz) 24000/F(KHz) 30 100 150 200 500 Measurement Distance
(meters) 300 30 30 3 3 3 3 LIMITS OF RADIATED EMISSION MEASUREMENT (Above 1000MHz) Frequency (MHz) Above 1000 Notes:
(dBuV/m) (at 3 meters) PEAK 74 AVERAGE 54
(1) The limit for radiated test was performed according to FCC PART 15C.
(2) The tighter limit applies at the band edges.
(3) Emission level (dBuV/m)=20log Emission level (uV/m).
(4) The test result calculated as following:
Measurement Value = Reading Level + Correct Factor Correct Factor = Antenna Factor + Cable Loss - Amplifier Gain(if use) Margin Level = Measurement Value - Limit Value Spectrum Parameter Attenuation Start Frequency Stop Frequency RBW / VBW Setting Auto 1000 MHz 10th carrier harmonic RBW 1MHz VBW 3MHz peak detector for Pk value
(Emission in restricted band) RMS detector for AV value Report No.: BTL-FCCP-1-1603C186 Page 15 of 61 Receiver Parameter Attenuation Start ~ Stop Frequency Start ~ Stop Frequency Start ~ Stop Frequency Start ~ Stop Frequency Start ~ Stop Frequency Setting Auto 9KHz~90KHz for PK/AVG detector 90KHz~110KHz for QP detector 110KHz~490KHz for PK/AVG detector 490KHz~30MHz for QP detector 30MHz~1000MHz for QP detector 4.2.2 TEST PROCEDURE a. The measuring distance of 3 m shall be used for measurements. The EUT was placed on the top of a rotating table 0.8 meter above the ground at a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation.(below 1GHz) b. The measuring distance of 3 m shall be used for measurements. The EUT was placed on the top of a rotating table 1.5 meter above the ground at a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation.(above 1GHz) c. The height of the equipment or of the substitution antenna shall be 0.8 m or 1.5 m, the height of the test antenna shall vary between 1 m to 4 m. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. The initial step in collecting radiated emission data is a receiver peak detector mode pre-scanning the measurement frequency range. Significant peaks are then marked and then Quasi Peak detector mode re-measured. e. All readings are Peak unless otherwise stated QP in column of Note. Peak denotes that the Peak reading compliance with the QP Limits and then QP Mode measurement didnt perform.
(below 1GHz) f. All readings are Peak Mode value unless otherwise stated AVG in column of Note. If the Peak Mode Measured value compliance with the Peak Limits and lower than AVG Limits, the EUT shall be deemed to meet both Peak & AVG Limits and then only Peak Mode was measured, but AVG Mode didnt perform. (above 1GHz) g. For the actual test configuration, please refer to the related Item EUT Test Photos. 4.2.3 DEVIATION FROM TEST STANDARD No deviation Report No.: BTL-FCCP-1-1603C186 Page 16 of 61 4.2.4 TEST SETUP
(A) Radiated Emission Test Set-Up Frequency Below 1 GHz
(B) Radiated Emission Test Set-Up Frequency Above 1 GHz Report No.: BTL-FCCP-1-1603C186 Page 17 of 61
(C) For radiated emissions below 30MHz 4.2.5 EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 4.1.5 unless otherwise a special operating condition is specified in the follows during the testing. 4.2.6 EUT TEST CONDITIONS Temperature: 22C Relative Humidity: 56% Test Voltage: AC 120V/60Hz 4.2.7TEST RESULTS (9KHZ TO 30MHZ) Please refer to the Attachment B Remark:
(1) The amplitude of spurious emissions which are attenuated by more than 20 dB below the permissible value has no need to be reported.
(2) Distance extrapolation factor = 40 log (specific distance / test distance) (dB).
(3) Limit line = specific limits (dBuV) + distance extrapolation factor. Report No.: BTL-FCCP-1-1603C186 Page 18 of 61 4.2.8TEST RESULTS (30MHZ TO 1000 MHZ) Please refer to the Attachment C. Remark:
(1) All readings are Peak unless otherwise stated QP in column ofNote. Peak denotes that the Peak reading compliance with the QP Limits and then QP Mode measurement didnt perform.
(2) Measuring frequency range from 30MHz to 1000MHz.
(3) If the peak scan value lower limit more than 20dB, then this signal data does not show in table. 4.2.9TEST RESULTS (ABOVE 1000 MHZ) Please refer to the Attachment D. Remark:
(1) All readings are Peak unless otherwise stated QP in column ofNote. Peak denotes that the Peak reading compliance with the QP Limits and then QP Mode measurement didnt perform.
(2) Radiated emissions measured in frequency range above 1000MHz were made with an instrument using Peak detector mode and AV detector mode of the emission
(3) A preamp and high pass filter were used for this test in order to provide sufficient measurement sensitivity.
(4) EUT Orthogonal Axis:
X - denotes Laid on TableY - denotes Vertical StandZ - denotes Side Stand
(5) During the measurements above 1 GHz it is taken care of that the EUT is always within the 3 dB cone of radiation BW of the used antenna
(6) No limit: This is fundamental signal, the judgment is not applicable. For fundamental signal judgment was referred to Peak output test. Report No.: BTL-FCCP-1-1603C186 Page 19 of 61 5. BANDWIDTH TEST 5.1 APPLIED PROCEDURES / LIMIT FCC Part15 (15.247) , Subpart C Section Test Item Limit 15.247(a)(2) Bandwidth 5.1.1 TEST PROCEDURE
>= 500KHz
(6dB bandwidth) Frequency Range
(MHz) Result 2400-2483.5 PASS a. The EUT was directly connected to the spectrum analyzer and antenna output port as show in the block diagram below, b. Spectrum Setting : RBW= 100KHz, VBW=300KHz, Sweep time = 2.5 ms. 5.1.2 DEVIATION FROM STANDARD No deviation. 5.1.3 TEST SETUP 5.1.4 EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 4.1.5 unless otherwise a special operating condition is specified in the follows during the testing. 5.1.5 EUT TEST CONDITIONS Temperature: 24C Relative Humidity: 60% Test Voltage: AC 120V/60Hz 5.1.6 TEST RESULTS Please refer to the Attachment E. Report No.: BTL-FCCP-1-1603C186 Page 20 of 61 6. MAXIMUM OUTPUT POWER TEST 6.1 APPLIED PROCEDURES / LIMIT FCC Part15 (15.247) , Subpart C Section Test Item Limit Frequency Range
(MHz) 15.247(b)(3) Maximum Output Power 1 watt or 30dBm 2400-2483.5 Result PASS 6.1.1 TEST PROCEDURE a. The EUT was directly connected to the power meter and antenna output port as show in the block diagram below, b. The maximum peak conducted output power was performed in accordance with method 9.1.2 of FCC KDB 558074 D01 DTS Meas Guidance v03r04. 6.1.2 DEVIATION FROM STANDARD No deviation. 6.1.3 TEST SETUP 6.1.4 EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 4.1.5 unless otherwise a special operating condition is specified in the follows during the testing. 6.1.5 EUT TEST CONDITIONS Temperature: 24C Relative Humidity: 60% Test Voltage: AC 120V/60Hz 6.1.6 TEST RESULTS Please refer to the Attachment F. Report No.: BTL-FCCP-1-1603C186 Page 21 of 61 7. ANTENNA CONDUCTED SPURIOUS EMISSION 7.1 APPLIED PROCEDURES / LIMIT In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated device is operating, the RF power that is produced shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided that the transmitter demonstrates compliance with the peak conducted power limits. 7.1.1 TEST PROCEDURE the block diagram below, a. The EUT was directly connected to the spectrum analyzer and antenna output port as show in b. Spectrum Setting : RBW= 100KHz, VBW=300KHz, Sweep time = 10 ms. c. Offset=antenna gain+cable loss 7.1.2 DEVIATION FROM STANDARD No deviation. 7.1.3 TEST SETUP 7.1.4 EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 4.1.5 unless otherwise a special operating condition is specified in the follows during the testing. 7.1.5 EUT OPERATION CONDITIONS Temperature: 24C Relative Humidity: 60% Test Voltage: AC 120V/60Hz 7.1.6 TEST RESULTS Please refer to the Attachment G. Report No.: BTL-FCCP-1-1603C186 Page 22 of 61 8. POWER SPECTRAL DENSITY TEST 8.1 APPLIED PROCEDURES / LIMIT FCC Part15 (15.247) , Subpart C Section Test Item Limit 15.247(e) Power Spectral Density 8 dBm
(in any 3KHz) 8.1.1 TEST PROCEDURE Frequency Range
(MHz) Result 2400-2483.5 PASS a. The EUT was directly connected to the spectrum analyzer and antenna output port as show in b. Spectrum Setting: RBW=3KHz, VBW=10 KHz, Sweep time = auto. the block diagram below, 8.1.2 DEVIATION FROM STANDARD No deviation. 8.1.3 TEST SETUP 8.1.4 EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 4.1.5 unless otherwise a special operating condition is specified in the follows during the testing. 8.1.5 EUT TEST CONDITIONS Temperature: 24C Relative Humidity: 60% Test Voltage: AC 120V/60Hz 8.1.6 TEST RESULTS Please refer to the Attachment H. Report No.: BTL-FCCP-1-1603C186 Page 23 of 61 9. MEASUREMENT INSTRUMENTS LIST Conducted Emission Measurement Calibrated until Mar. 27, 2017 Mar. 27, 2017 Mar. 10, 2017 Mar. 27, 2017 Mar. 27, 2017 N/A Calibrated until Mar. 27, 2017 Nov. 09, 2016 Oct. 11, 2016 Jun. 28, 2016 N/A N/A Item Kind of Equipment Manufacturer 1 2 3 LISN LISN Test Cable 4 EMI Test Receiver 50 Terminator 5 Measurement 6 Software EMCO R&S emci R&S SHX Farad Type No. 3816/2 ENV216 RG223(9KHz-30M Hz) ESCI TF2-3G-A EZ-EMC Ver.NB-03A1-01 Serial No. 0052765 101447 C_17 100382 08122901 N/A Radiated Emission Measurement Item Kind of Equipment Manufacturer Schwarbeck 1 2 3 Antenna Amplifier Receiver 4 5 6 7 8 9 Test Cable Controller Measurement Software Antenna Amplifier Receiver HP AGILENT emci CT Farad ETS Agilent AGILENT 10 Test Cable emci Type No. VULB9160 8447D N9038A Serial No. 9160-3232 2944A09673 MY52130039 LMR-400(30MHz-1 GHz) SC100 EZ-EMC Ver.NB-03A1-01 C-01 N/A N/A 3115 8449B N9038A 00075789 3008A02274 MY52130039 Mar. 27, 2017 Nov. 01, 2016 Oct. 11, 2016 EMC104-SM-SM-1 0000(1GHz-26.5G Hz) C-68 Jun. 28, 2016 11 Broad-Band Horn Antenna Microwave Preamplifier With Adaptor Active Loop Antenna 12 13 Schwarzbeck BBHA 9170 9170319 Mar. 27, 2017 EMC INSTRUMENT EMC2654045 980039 &
HA01 Mar. 27, 2017 R&S HFH2-Z2 830749/020 Sep. 07, 2016 Report No.: BTL-FCCP-1-1603C186 Page 24 of 61 Item Kind of Equipment 1 Spectrum Analyzer Manufacturer R&S Type No. FSP 40 Serial No. 100185 Calibrated until Oct. 11, 2016 6dB Bandwidth Measurement Item Kind of Equipment 1 2 Power Meter Pulse Power Sensor Peak Output Power Measurement Manufacturer ANRITSU ANRITSU Type No. ML2495A Serial No. 1128009 Calibrated until Mar. 27, 2017 MA 2411B 1027500 Mar. 27, 2017 Antenna Conducted Spurious Emission Measurement Item Kind of Equipment 1 Spectrum Analyzer Manufacturer R&S Type No. FSP 40 Serial No. 100185 Calibrated until Oct. 11, 2016 Item Kind of Equipment 1 Spectrum Analyzer R&S Type No. FSP 40 Serial No. 100185 Calibrated until Oct. 11, 2016 Power Spectral Density Measurement Manufacturer Remark: N/A denotes no model name, serial no. or calibration specified. All calibration period of equipment list is one year. Report No.: BTL-FCCP-1-1603C186 Page 25 of 61 ATTACHMENT A - CONDUCTED EMISSION Report No.: BTL-FCCP-1-1603C186 Page 26 of 61 Test Mode:
TX Mode Line Report No.: BTL-FCCP-1-1603C186 Page 27 of 61 Test Mode:
TX Mode Neutral Report No.: BTL-FCCP-1-1603C186 Page 28 of 61 ATTACHMENT B - RADIATED EMISSION (9KHZ TO 30MHZ) Report No.: BTL-FCCP-1-1603C186 Page 29 of 61 Test Mode:
TX Mode Frequency
(MHz) 0.0098 0.0098 0.0286 0.0286 0.0368 0.0368 0.0562 0.0562 0.5081 1.9523 Ant 0/90 0 0 0 0 0 0 0 0 0 0 Frequency
(MHz) 0.0124 0.0124 0.0258 0.0258 0.0446 0.0446 0.0575 0.0575 0.6225 2.0534 Ant 0/90 90 90 90 90 90 90 90 90 90 90 Read level dBuV/m 13.42 14.29 6.34 8.50 3.41 5.46 1.20 2.48 19.62 23.24 Read level dBuV/m 13.57 14.45 7.30 8.61 5.32 6.20 1.63 2.42 22.20 24.53 Factor
(dB) 24.95 24.95 23.76 23.76 23.24 23.24 22.28 22.28 19.83 19.50 Factor
(dB) 24.30 24.30 23.93 23.93 22.74 22.74 22.25 22.25 20.19 19.47 Measured(FS) Limit
(dBuV/m) 38.37 39.24 30.10 32.26 26.65 28.70 23.48 24.76 39.45 42.74 Measured(FS)
(dBuV/m) 37.87 38.75 31.23 32.54 28.06 28.94 23.88 24.67 42.39 44.00
(dBuV/m) 127.78 147.78 118.48 138.48 116.29 136.29 112.61 132.61 73.49 69.54 Limit
(dBuV/m) 125.74 145.74 119.37 139.37 114.62 134.62 112.41 132.41 71.72 69.54 Note Margin
(dB) AVG
-89.41
-108.54 PEAK
-88.38 AVG
-106.22 PEAK
-89.64 AVG
-107.59 PEAK
-89.13 AVG
-107.85 PEAK
-34.04 QP QP
-26.80 Note Margin
(dB)
-87.87 AVG
-106.99 PEAK
-88.14 AVG
-106.83 PEAK
-86.56 AVG
-105.68 PEAK
-88.53 AVG
-107.74 PEAK QP
-29.33
-25.54 QP Report No.: BTL-FCCP-1-1603C186 Page 30 of 61 ATTACHMENT C - RADIATED EMISSION (30MHZ TO 1000MHZ) Report No.: BTL-FCCP-1-1603C186 Page 31 of 61 Test Mode:
TX 2402MHz -CH00 -1Mbps Vertical Report No.: BTL-FCCP-1-1603C186 Page 32 of 61 Test Mode:
TX 2402MHz -CH00 -1Mbps Horizontal Report No.: BTL-FCCP-1-1603C186 Page 33 of 61 Test Mode:
TX 2440MHz -CH19 -1Mbps Vertical Report No.: BTL-FCCP-1-1603C186 Page 34 of 61 Test Mode:
TX 2440MHz -CH19 -1Mbps Horizontal Report No.: BTL-FCCP-1-1603C186 Page 35 of 61 Test Mode:
TX 2480MHz -CH39 -1Mbps Vertical Report No.: BTL-FCCP-1-1603C186 Page 36 of 61 Test Mode:
TX 2480MHz -CH39 -1Mbps Horizontal Report No.: BTL-FCCP-1-1603C186 Page 37 of 61 ATTACHMENT D - RADIATED EMISSION (ABOVE 1000MHZ) Report No.: BTL-FCCP-1-1603C186 Page 38 of 61 Test Mode :
TX 2402MHz _CH00_1Mbps Vertical Report No.: BTL-FCCP-1-1603C186 Page 39 of 61 Test Mode :
TX 2402MHz _CH00_1Mbps Vertical Report No.: BTL-FCCP-1-1603C186 Page 40 of 61 Test Mode :
TX 2402MHz _CH00_1Mbps Horizontal Report No.: BTL-FCCP-1-1603C186 Page 41 of 61 Test Mode :
TX 2402MHz _CH00_1Mbps Horizontal Report No.: BTL-FCCP-1-1603C186 Page 42 of 61 Test Mode :
TX 2440MHz _CH19_1Mbps Vertical Report No.: BTL-FCCP-1-1603C186 Page 43 of 61 Test Mode :
TX 2440MHz _CH19_1Mbps Vertical Report No.: BTL-FCCP-1-1603C186 Page 44 of 61 Test Mode :
TX 2440MHz _CH19_1Mbps Horizontal Report No.: BTL-FCCP-1-1603C186 Page 45 of 61 Test Mode :
TX 2440MHz _CH19_1Mbps Horizontal Report No.: BTL-FCCP-1-1603C186 Page 46 of 61 Test Mode :
TX 2480MHz _CH39_1Mbps Vertical Report No.: BTL-FCCP-1-1603C186 Page 47 of 61 Test Mode :
TX 2480MHz _CH39_1Mbps Vertical Report No.: BTL-FCCP-1-1603C186 Page 48 of 61 Test Mode :
TX 2480MHz _CH39_1Mbps Horizontal Report No.: BTL-FCCP-1-1603C186 Page 49 of 61 Test Mode :
TX 2480MHz _CH39_1Mbps Horizontal Report No.: BTL-FCCP-1-1603C186 Page 50 of 61 ATTACHMENT E - BANDWIDTH Report No.: BTL-FCCP-1-1603C186 Page 51 of 61 Test Mode:
TX Mode Frequency
(MHz) 2402 2440 2480 6dB Bandwidth 99% Occupied BW
(MHz) 0.63 0.63 0.64
(MHz) 1.30 1.32 1.18 TX CH00 Min. Limit
(kHz) 500 500 500 Test Result Complies Complies Complies Report No.: BTL-FCCP-1-1603C186 Page 52 of 61 TX CH19 TX CH39 Report No.: BTL-FCCP-1-1603C186 Page 53 of 61 ATTACHMENT F - MAXIMUM OUTPUT POWER TEST Frequency
(MHz) 2402 2440 2480 Conducted Power (dBm) 0.22
-0.47
-1.46 Test Mode Conducted Power (W) 0.0011 0.0009 0.0007 Max. Limit Max. Limit
(dBm) 30.00 30.00 30.00
(W) 1.00 1.00 1.00 Result Complies Complies Complies Report No.: BTL-FCCP-1-1603C186 Page 54 of 61 ATTACHMENT G - ANTENNA CONDUCTED SPURIOUS EMISSION Report No.: BTL-FCCP-1-1603C186 Page 55 of 61 Test Mode :
CH00, CH19 , CH39 - 1Mbps CH00 (Lower) - 1Mbps CH39 (upper) - 1Mbps Report No.: BTL-FCCP-1-1603C186 Page 56 of 61 CH00 (10 Harmonic of the frequency) CH19 (10 Harmonic of the frequency) Report No.: BTL-FCCP-1-1603C186 Page 57 of 61 CH39 (10 Harmonic of the frequency) Report No.: BTL-FCCP-1-1603C186 Page 58 of 61 ATTACHMENT H - POWER SPECTRAL DENSITY TEST Report No.: BTL-FCCP-1-1603C186 Page 59 of 61 Test Mode:
TX Mode Frequency
(MHz) 2402 2440 2480 Power Density
(dBm/3kHz) Power Density
(mW/3kHz) Max. Limit
(dBm/3kHz)
-13.83
-14.07
-15.06 0.04 0.04 0.03 TX CH00 8.00 8.00 8.00 Result Complies Complies Complies Report No.: BTL-FCCP-1-1603C186 Page 60 of 61 TX CH19 TX CH39 Report No.: BTL-FCCP-1-1603C186 Page 61 of 61
This product uses the FCC Data API but is not endorsed or certified by the FCC