802.11 b/g/n RTL8723DE Combo module User Manual

RTL8723DE Users Manual RTL8723DE PCI-Express NGFF1630-S2-E Users Manual Realtek Semiconductor Corp. No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan Tel.: +886-3-578-0211. Fax: +886-3-577-6047 www.realtek.com.tw RTL8723DE Users Manual Installing the Wireless PCIe NGFF1630 module Hardware Step . Shut down the computer. Step . Installing PCIe NGFF module to PCIe NGFF connector. RTL8723DE Users Manual Step . Connect two external Wi-Fi antennas on I-PEX connectors. step%. Power on the computer. RTL8723DE Users Manual Un-installing the Wireless PCIe NGFF1630 module Hardware Step . Shut down the computer. Step . Remove external Wi-Fi Antennas from the Wireless PCIe NGFF module board. Step . Remove the Wireless PCIe NGFF module board from PCIe RTL8723DE Users Manual NGFF connector port. Step %. Power on the computer. Installing the Wireless PCIe NGFF1630 module Software Before you proceed with the installation, please notice following descriptions. Note1: The following installation was operated under Windows 7. Note2: If you have installed the WLAN driver & utility before, please uninstall the old version first. If you install the Realtek11n Single Chip PCIE WLAN NIC Mass production kit into your laptop computer before installing the software RTL8723DE Users Manual program from the CD. A. Insert the Installation CD to your CD-ROM Drive. Execute the setup Program, Click Next to process the installation B. Click Install to process the installation RTL8723DE Users Manual C. Click Install this driver software anyway D. After step C please press Next button. E. Please click YES to install BT package. RTL8723DE Users Manual F. Please click to continue. G. Please click to continue. RTL8723DE Users Manual H. Please click to start installation. I. Please click to finish the installation. RTL8723DE Users Manual J. Press Finish button to complete the install process RTL8723DE Users Manual Un-installing the Wireless PCIe NGFF1630 module Software If you install Realtek11n Single Chip PCIE WLAN NIC Mass production kit into your laptop computer after installing the software program from the CD. When you install Realtek11n Single Chip WLAN PCIE NGFF1630 Adapter, the following dialog will be shown. A. Uninstall the RTL8723DE WLAN Driver from Start All Programs REALTEK 11n 8723DE PCIE WLAN NIC Massproduction kit Please click Uninstall to remove RTL8723DE WLAN driver. RTL8723DE Users Manual Installing the Bluetooth USB Module Software A. Insert the NGFF1630 card into system connector. B. Boot on system then the Geniric Bluttooth Adapter device will show up in device manager. C. Click right button on RT Bluetooth Radio and select Update Driver. RTL8723DE Users Manual D. After select Update Driver Software then the Hardware Update Wizard will pop up, please select Browse my computer for driver software and press Next button. E. After step D please Select Let me pick from a list of device drivers on my computer . RTL8723DE Users Manual F. Finish step E then select Have Disk.. G. Now select browse to find the driver for device and press Next button.(The drivers locate is the same with WiFi driver ) RTL8723DE Users Manual RTL8723DE Users Manual H. Then click Install this driver software anyway to continue. I. Press close button to complete the install process and you can see the Driver will be show up in Device Manager. RTL8723DE Users Manual Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

-

-

-

-

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This EUT is compliance with SAR for general population/uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C. This equipment should be installed and operated with minimum distance 0.5 cm between the radiator & your body. RTL8723DE Users Manual IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 13. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. Ant. Brand Model Name Antenna

(P/N) Type Connector Gain(dBi) LYNwave ALA110-222050-300011 PIFA PSA RFDPA171320EMLB301 Dipole I-PEX I-PEX 3.5dBi 3.14dBi 1 2 Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains TX FCC ID:

TX2-RTL8723DE ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. RTL8723DE Users Manual Industry Canada Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device French translation:

Ce dispositif est conforme aux CNR d'IndustrieCanada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. This device has been designed to operate with an antenna having a maximum gain of 3.5dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication. French translation:

Ce dispositif a t conu pour fonctionner avec une antenne ayant un gain maximum de 3.5 dBi. Une antenne gain plus lev est strictement interdite par les rglements d'Industrie Canada. L'impdance d'antenne requise est de 50 ohms. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peutfonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pourl'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que lapuissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. IMPORTANT NOTE:

IC Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. RTL8723DE Users Manual French translation:

NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles) Dclaration d'exposition aux radiations:

Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. For product available in the Canada market, only channel 1~13 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux Canada du march, seul le canal 1 13 peuvent tre exploits. Slection d'autres canaux n'est pas possible. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with IC multi-transmitter product procedures. Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without reassessment permissive change. Cet appareil et son antenne (s) ne doit pas tre co-localiss ou fonctionnement en association avec une autre antenne ou transmetteur. This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. USERS MANUAL OF THE END PRODUCT:

In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. RTL8723DE Users Manual LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains IC :

6317A-RTL8723DE ". The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online. This radio transmitter (IC:6317A-RTL8723DE) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio(IC:6317A-RTL8723DE) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Ant. Brand Model Name Antenna

(P/N) Type Connector Gain(dBi) LYNwave ALA110-222050-300011 PIFA PSA RFDPA171320EMLB301 Dipole I-PEX I-PEX 3.5dBi 3.14dBi 1 2 Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. NCC RTL8723DE Users Manual XXXyyyLPDzzzz-x (NCC ID) Japan Statement Host system must be labeled with "Contains MIC ID:xxxxxx, MIC ID displayed on label