Automate Motor Programming Guide y Please refer to separate Rollease Acmeda System Assembly Manual for full assembly instructions relevant to the hardware system being used. 2. BATTERY MANAGEMENT For battery motors;
Prevent discharging the battery completely for extended periods, recharge as soon as the battery is discharged CHARGING NOTES Before first use please charge motor for 6 hours, using the recommended AC charger During operation, if battery is low, the motor will beep 10 times to prompt the user it needs charging. 3. PRODUCT RANGE The Quick Start Programming Guide is universal for all Automate Motors including:
1. ASSEMBLY 3. PRODUCT RANGE (cont.) 3. PRODUCT RANGE (cont.) INSTALLER BEST PRACTICE AND TIPS SLEEP MODE If pre-programmed: before shipping the motor ensure the motor is put into sleep mode so it doesnt activate during transit. P1 LOCATIONS P1 P1 0.6 Cord Lift LOCK REMOTE Prevent users accidently changing the limit;
ensure the remote is locked as your last step of programming. ZONE / GROUPS Internal Tubular P1 0.8 Cord Lift Hold P1 P1 0.8 Cord Lift Ask the customer the day before to think how shades will be zoned on the remote. This may save an extra call out. SETTLE FABRIC Run the fabric up and down several times to ensure fabric has settled to some extent and re adjust the limits if needed. CHARGE 100%
Curtain Tilt Motor For battery motors ensure the motor is fully charged as per instructions. Note: Curtain motor does not Jog but instead LED flashes INSTALLERS REMOTE Use a spare remote to individually program each shade. Then use that remote to group rooms as per the users needs. If you go back and service the installation later then, that same remote can be used to check the individual shades. 0.6 Cord Lift Hold P1 P1 GREEN SAFETY Tilt Motor WARNING: Important safety instructions to be read before installation and use. Incorrect installation or use can lead to serious injury and will void manufacturers liability and warranty. It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference. Do not expose to water,moisture, humid and damp environments or extreme temperatures. Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, should not be allowed to use this product. Use or modification outside the scope of this instruction manual will void warranty. Installation and programming to be performed by a suitably qualified installer. Follow installation instructions. For use with motorized shading devices. Keep away from children. Frequently inspect for improper operation. Do not use if repair or adjustment is necessary. Keep clear when in operation. Replace battery with correctly specified type. Curtain P1 Large Tubular Internal Tubular Large Tubular DISPOSAL AND RECYCLING Do not dispose of in general waste. INSTALLER QUICK START PROGRAMMING STEP 3 CHECK DIRECTION This setup wizard should be used for new installation or factory reset motors only. Individual steps may not work if you haven't followed the wizard from the beginning. STEP 1 ON REMOTE STEP 2 ON REMOTE OR STEP 5 SET UPPER LIMIT STEP 6 SET BOTTOM LIMIT STEP 7 SAVE YOUR LIMIT 2 SECS
* Internal Tubular pictured. Refer to P1 Locations for specific devices Press the P1 button on the motor for 2 Seconds until the motor responds as below E S N O P S E R R O T O M JOGx2 BEEP x1 Press up or down to check the motor direction. If correct skip to step 5. STEP 4 CHANGE DIRECTION If the shade direction needs to be reversed;
press and hold the up & down arrow together for 5 seconds until the motor Jogs. 5 SECS MOTOR RESPONSE JOGx1 5 SECS 5 SECS 6 SECS Move shade to desired top limit by pressing the up arrow repeatedly. Then press and hold up & stop together for 5 sec to save limit. Move shade to desired bottom limit by pressing the down arrow repeatedly. Then press and hold down & stop together for 5 sec to save limit. Repeat steps 1-6 for all motors. Once complete Press and hold the Lock button for 6 seconds while looking at the LED, and hold until solid. E S N O P S E R R O T O M JOGx2 BEEP x3 E S N O P S E R R O T O M JOGx2 BEEP x3 Select a single or multiple channels by toggling channels as required. Note the corresponding LED next to each channel. Within 4 seconds hold the stop button on the remote for 3 seconds. The motor will respond with Jog and Beep Reversing motor direction using this method is only possible during initial set-up. Tap the arrow several times or hold down if needed; press arrow to stop. Tap the arrow several times or hold down if needed; press arrow to stop. CAUTION This device complies with Part 15 of the FCC Rules /
Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference.
(2) this device must accept any interference received, including interference that may cause undesired operation. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : 1. Lappareil ne doit pas produire de brouillage; 2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FACTORY RESET MOTOR RESET PROCEDURE To reset all settings in the motor press and hold the P1 Button for 14 seconds, you should see 4 independent jogs followed by 4x Beeps at the end. 14 SECS
* Internal Tubular pictured above. Refer to P1 Locations for specific devices MOTOR RESPONSE 2 SECS 6 SECS 10 SECS 14 SECS BEEPx4 I E D U G R E S U I E D U G R E S U BUTTON OVERVIEW REPLACE BATTERY N O T T U B P O T S N O T T U B P U N O T T U B N W O D L E N N A H C WALL MOUNTING Use supplied fasteners and anchors to attach the base to wall. GROUP CONTROL Channel "ALL" is pre-set to control ALL shades paired to your Muli-channel remote. Remove cover from remote;
unscrew with screw driver then firmly press down and slide left. Replace cover by pressing snap latches into place. SELECTING A CHANNEL CONTROL SHADE UP OR DOWN STOPPING THE SHADE
) 2 P
(
G N I T T E S K C O L Install battery CR2430 with positive (+) side facing up. Press any ch to see previously selected channels. The last selected channel will remain in memory. To un-select a channel press the same channel and select any new channels. While the channel is displayed press up or down to move shade accordingly Press the stop button to stop shade at any point I E D U G T R A T S K C U Q I I G N M M A R G O R P D E C N A V D A DISABLE LIMIT SETTING This mode is intended to be used after all shade programming is completed. User Mode will prevent accidental or unintended changing of limits. SET A FAVORITE POSITION Move shade to desired position by pressing UP or DOWN on the remote. Push switch to lock or unlocked position OR P 2 MOTOR RESPONSE JOGx2 BEEP x3 Press STOP on controller CREATE CUSTOM GROUPS It is possible to copy one channel to another channel to create custom groups For 5 CH MOTOR RESPONSE d e k c o l n u n e h w g n k n i l b D E L i d e k c o l n e h w n o d i l o s D E L Pressing the lock button for 6 second will toggle between locked and unlocked LED show Solid or flashing Press P2 on controller MOTOR RESPONSE JOGx1 BEEP x1 JOGx1 BEEP x1 Press STOP on controller STEP 1. EXISTING REMOTE Select the channel you want to transfer STEP 2. NEW REMOTE Select the channel you want to transfer too P 2 P 2 MOTOR RESPONSE JOGx1 BEEP x1 Press P2 Button on existing remote. MOTOR RESPONSE JOGx1 BEEP x1 P 2 Press P2 Button again on existing remote. Next step to be completed within 4 seconds of Step 1 MOTOR RESPONSE JOGx1 BEEP x1 Press P2 Button on new remote.