submitted | available | document details (if available) | source link |
---|---|---|---|
February 08 2013 | February 08 2013 |
various | Users Manual | Users Manual | 871.64 KiB | February 08 2013 |
8252 Smart DECT Handset Reference Guide 1.) Phone description 14 9 10 7 5 4 2 3 1 6 8 14 11 12 13 Access menu Answer the call 1 2 Hang up 3 Return to previous menu; erase a character; delete an entire field 4 5 Navigate and confirm 6 Numeric digit keys 7 8 Home: Back to homepage Soft key: Left; Mid; Right 9 F1: Function key 1 F2: Function key 2 Silent: set to silent mode LED:
green steady: the phone is on the charger and the battery is fully charged red steady: the phone is on the charger and the battery is charging slow yellow flashing: telephonic event such as unread message, missed call, etc. rapid yellow flashing: incoming call 3.5mm jack plug for headset 10 11 Volume up; Volume down; Emergency call 12 13 Micro USB port to PC 14 Power on/ off handset 5V supply input to charger 2.) Installing the battery in the handset 3.) Charging handset battery 4.) Switching on handset 5.) Call for conversation 5.1) Making a call Dial numeric digit keys Send the call, you are in communication Press hang up key to end the call 5.1) Receiving a call To prevent possible hearing damage, do not listen at high volume levels for long periods. Only used at altitude not exceeding 2000m. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Increase the separation between the equipment and receiver. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. IC SAR Waring :
The device has been tested and compliance with SAR limits, users can obtain Canadian information on RF exposure and compliance. Le prsent appareil est conforme Aprs examen de ce matriel aux conformit aux limites DAS et/ou aux limites dintensit de champ RF, les utilisateurs peuvent sur lexposition aux radiofrquences et la conformit and compliance dacqurir les informations correspondantes Customer Information 1. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. 2. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. If this equipment [US: T7HW4NANCT8131] causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. 3. 4. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the 5. operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with this equipment [US: T7HW4NANCT8131], for repair or warranty information, Service can be facilitated through our office at:
U.S. Agent Company name: RTX America Inc. Address: 501 AirTech Parkway Plainfield IN 46168 USA Tel: 1-408-441-8600 If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. 6. Please follow instructions for repairing if any (e.g. battery replacement section); otherwise do not alternate or repair any parts of device except specified. For repair procedures, follow the instructions outlined under the limited warranty. 7. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission 8. 9. or corporation commission for information. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this [CT8131]
does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. If the telephone company requests information on what equipment is connected to their lines, inform them of:
a) The ringer equivalence number [NAN]
Facility Interface Codes (FIC) [N/A]
b) The USOC jack required [N/A]
c) d) Service Order Codes (SOC) [N/A]
e) The FCC Registration Number [US: T7HW4NANCT8131]
10. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. The REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point. For this product the FCC Registration number is [US: T7HW4NANCT8131] indicates the REN would be NAN 11. This product is equipped with a corded or cordless handset, it is hearing aid compatible
This product uses the FCC Data API but is not endorsed or certified by the FCC