FCC ID: A3LMB8811QAN Bluetooth Module

Bluetooth Module : MB8811QAN

[top] [bottom]

This MB8811QAN Module is compatible with Bluetooth specification version 4.2. MB8811QAN is a fully integrated RF, baseband controller etc. SPECIFICATION Main Chips Standards CSR8811A12 Bluetooth 4.2 Frequency Band 2402 ~ 2480 MHz Tx Power Rx Sensitivity Distance Power Voltage Dimension Environmental Range 0.25 ~ 10mW (Bluetooth Power Class 1)

< -70dBm (BER 0.1%)

< 10m (open space) 3.3V 18.631.2 3.4 mm Operation temperature : -25 ~ +70 Modulation mode GFSK, 8DPSK Communication method FHSS Pin define(TOP PIN MAP) No 1 2 3 4 5 6 7 8 9 10 Pin Name I/O Description VDD RESET RTS CTS TX GND RX GND SCL SDA I I O I O

-

I

-

O I/O Positive Input for the internal regulator (3.0 ~ 3.6V) Reset if low. Input debounced so must be low for >5ms to cause a reset Bluetooth UART Request to Send. Active-low request. Bluetooth UART Clear to Send.Active-low clear. Bluetooth UART Serial Output. Ground. Bluetooth UART Serial Input. Ground. I2C interface Clock I2C interface DATA 1. VDD 2.RESET 3.RTS 4.CTS 5.TX 6.GND 7.RX 8.GND 9.SCL 10.SDA Dimension TOP View Mark Dimension Mark Dimension Mark Dimension A B C 31.600.3 18.600.3 8.00.2 D E F 2.600.2 2.00.2 1.80.2 G 1.00.2

(Unit : mm) Electrical Characteristics Conditions : VDD = 3.3V, Ta = 25 , unless otherwise noted. Absolute Maximum Ratings Parameter Power Supply Voltage : VDD Storage Temperature Recommended Operating Conditions Parameter Power Supply Voltage Operation Temperature Current consumption Parameter Page scan, Time interval = 1.28s Inquiry and Page scan, Time interval = 1.28s ACL No data transfer ACL data transfer Input/Output Characteristics Parameter VIL Input Voltage Low VIH Input Voltage High VOL Output Voltage Low VOH Output Voltage High Min

-0.4V

-40 Max 3.6V 85 Unit DCV Min 3.0V

-25 Max 3.6V 70 Unit DCV Connection Type Avg Peak Unit

-

-

Master Master 2 2 10 32 3 mA mA mA mA Min

-0.4 Max 0.8 0.7*VDD VDD+0.4

-

VDD-0.2 0.2

-

Unit V V V V General Performance Parameter Frequency Range Transmitter Performance Condition Normal Min 2402 Typ Max Unit

-

2480 MHz Parameter Condition Min Typ Max Unit Transmit Power Power density 20dB bandwidth Adjacent channel power

(F0 = 2441MHz) Out-band Spurious Emission Modulation Characteristic Initial Carrier Frequency Tolerance Carrier Frequency Drift Receiver Performance Normal Normal Normal F=F0 2MHz F=F0 3MHz F=F0 4MHz 30MHz ~ 1GHz 1GHz ~ 12.75GHz 1.8GHz ~ 1.9GHz 5.1GHz ~ 5.3GHz F1avg F2max F2avg / F1avg DH1 packet DH5 packet

-6 0

-

-

-

-

-

-

-

-

140 115 80

-75

-25

-

-

-

-

-

-

-

-

-

-

-

-

8 20 1000

-20

-40

-40

-36

-30

-47

-47 175

-

-

75 25 dBm dBm KHz dBm dBm dBm dBm dBm dBm dBm KHz KHz

%

KHz KHz Parameter Condition Min Type Max Unit Sensitivity at 0.1% BER Sensitivity at 0.1% BER Maximum received signal at 0.1% BER Maximum level of intermodulation interferers Single slot (DH1 packet) Multi slot (DH5 packet) f1-f2 = 5 MHz, Pwanted= -64 dBm

-

-

-20

-39

-

-

-

-

-70

-70

-

-

dBm dBm dBm dBm Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &

your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE:

20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. IC Statement This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. MB8811QAN Test Manual 1) RF Test Utility 2) First time, CSR Bluesuite program must be installed. you can use BTCli.exe and enter DUT(Device Under Test) mode. So RF equipment can inquiry and test. (reference document.)

* reference document : MB8811QA_JIG_DUT_BLE_MANUAL.pdf 3) RF Test method RF Test tool is BlueTest.exe at CSR bluesuite program. You can see detail explanation from reference document.

* reference document : BlueTest Instruction Manual.pdf Conformity Assessment Display Company name: Samsung Electronics Model : Specific micro-power wireless devices (wireless data communication system devices)

(MB8811QAN) Manufacture Year : 2019. Manufacturer / Manufacture Country : Samsung Electronics / Korea

CTK Co., Ltd.

(Ho-dong), 113, Yejik-ro, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-624-9501 www.e-ctk.com EUT Internal Photographs 1 / 1

CTK Co., Ltd.

(Ho-dong), 113, Yejik-ro, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-624-9501 www.e-ctk.com EUT External Photographs Antenna 1 / 1

CTK Co., Ltd.

(Ho-dong), 113, Yejik-ro, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-624-9501 www.e-ctk.com Label 1 / 1

19 Chapin Rd, Building D. Pine Brook, New Jersey Tel No : 973-808-6361 Fax No : -

Special Power of Attorney Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Product/ Model Number: BT module / MB8811QAN I, Jenni Chun of Samsung Electronics Co Ltd hereby Young-taek Lee of CTK Co., Ltd. to represent me to act on my behalf to do any and all of the following :

Sign on my behalf the agency, anti-drug and confidentiality cover letters and apply to FCC for the products. The right, powers and authority in fact to exercise any and all of the rights and powers herein granted shell commence and be in full force from 11/12/2019 and continue to e effective unless specifically terminated by either party. This authorization is limited to the product of as following:

FCC ID: A3LMB8811QAN Dated 11/12/2019, Sincerely,. NAME: Jenni Chun TITLE: General Manager Applicant: Samsung Electronics Co Ltd Address: 19 Chapin Rd, Building D. Pine Brook, New Jersey

19 Chapin Rd, Building D. Pine Brook, New Jersey Tel No : 973-808-6361 Fax No : -

Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: A3LMB8811QAN Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Block Diagram File Name Block Diagram (MB8811QAN).pdf Schematics (MB8811QAN).pdf Schematics_PCB Layout (MB8811QAN).pdf Part List (MB8811QAN).pdf Operational description (MB8811QAN).pdf Operational description_Ant Spec

(MB8811QAN).pdf Schematics Parts List Operational description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Minhyung Cho / General Manager Samsung Electronics Co Ltd

19 Chapin Rd, Building D. Pine Brook, New Jersey Tel No : 973-808-6361 Fax No : -

MODULAR APPROVAL LETTER 2019-11-12 Applicant: Samsung Electronics Co., Ltd. FCC ID: A3LMB8811QAN We would like to answer for Single Modular Approval in accordance with the requirement of rule part 15.212 as described below No. Requirements Comment Comply (Y/N) 1 2 3 4 5 The radio element of the modular transmitter has its own shielding The modular transmitter must have buffered modulation data/inputs (if such inputs are provided) The modular transmitter must have its own power supply regulation. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. The modular transmitter must be labeled with its own FCC ID. If the FCC ID is not visible when the module is installed inside Refer to the external photo the EUT has buffered data input. it is integrated in chip(GT24C02A-2TFLI-

TR) Power supply regulation (Part :

AZC399-04C.R7G) Refer to the internal photo The modular transmitter was tested in a stand-alone configuration. The peripherals in the Test Setup Photo document are Jig. 6 another device, then the outside of the device into which the Refer to the user manual module is installed must also display a label referring to the enclosed module The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete 7 transmitter and the manufacturer must provide adequate Refer to the user manual instructions along with the module to explain any such requirements 8 The modular transmitter must comply with any applicable RF exposure requirements Refer to the RF exposure statement for more details. Sincerely, NAME: Minhyung Cho Applicant: Samsung Electronics Co., Ltd. Y Y Y Y Y Y Y Y