FCC ID: 2AQZU-18010 CEILING FAN REMOTE CONTROLLER

.CEILING FAN REMOTE CONTROLLER OPERATION AND INSTALLATION INSTRUCTIONS

(Please keep this instruction pamphlet.) IMPORTANT YOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHT KIT (IF ANY) TO ON POSITION BEFORE OPERATING REMOTE CONTROL. IMPORTANT POINTS TO REMEMBER:

1. Read and save these instructions. 2. Please note that all fixed wiring appliances should be installed by a qualified electrician. 3. The supply to the remote control receiver should be connected through a mains switch, i.e. existing wall switch. 4. Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan. 5. Install receiver into the ceiling fan canopy of the fan to ensure proper protection. 6. This unit is to be used for the control of ceiling fan and in an AC120V 60Hz power supply only. 7. Do not install in wet locations or immerse in water. 8. Do not pull on or cut leads shorter. 9. Do not drop or bump the unit. 10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place as this will damage the transmitter. Dispose of used battery properly, keep the battery out of reach of children. 11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable (rheostat) wall control. INSTALLATION INSTRUCTIONS CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER. 1. Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pressing the Light Switch after installation. 2. Press and hold the emitters SET key for about 3S in 30 seconds of turning the Receivers AC power ON, The receiver learn the emitters CODE and the emitter can remote the receiver.(FIG.1 / 2 / 3) 3. Your transmitter is ready for use after 2pc DC1.5V/ AAA, battery installation(FIG. 1) FIG. 1 FIG. 2 FIG. 3 FUNCTIONS OF TRANSMITTER 1 ON/OFF - Press and release immediately to turn on or off light. DIMMER - Press and hold to dim or brighten light to the desired level and release.

(Only when the dip switch was set on D dimmer setting) 2. FAN SPEEDPressing key s 123

, it will control receiver FAN at speed 1~3 and OFF. 3. Pressing key

: Press and release immediately to set fan direction:

4.. Natural wind Function: Pressing key

, Fan will run in natural wind. 5.. Learning keys: Learning distance is no limition. Please press learning keysblack, Then receiver will remind that learning is finished. Only transmitter was learned can control receiver. 6. It has corresponding keys LED indicator, Pressing KEY, The LED indicator will flash. 7. key of color tempreture can be chosen to use. 8. Transmitter has learning key and toggle switch with 4 position (reserved). It has O/D switch. 9. Transmitter can be controlled by hand or you can place it in wall socket to control. To assure continued FCC compliance:

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. FCC ID2AQZU-18010 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC WARNING This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.

.CEILING FAN REMOTE CONTROLLER OPERATION AND INSTALLATION INSTRUCTIONS

(Please keep this instruction pamphlet.) IMPORTANT YOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHT KIT (IF ANY) TO ON POSITION BEFORE OPERATING REMOTE CONTROL. IMPORTANT POINTS TO REMEMBER:

1. Read and save these instructions. 2. Please note that all fixed wiring appliances should be installed by a qualified electrician. 3. The supply to the remote control receiver should be connected through a mains switch, i.e. existing wall switch. 4. Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan. 5. Install receiver into the ceiling fan canopy of the fan to ensure proper protection. 6. This unit is to be used for the control of ceiling fan and in an AC120V 60Hz power supply only. 7. Do not install in wet locations or immerse in water. 8. Do not pull on or cut leads shorter. 9. Do not drop or bump the unit. 10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place as this will damage the transmitter. Dispose of used battery properly, keep the battery out of reach of children. 11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable (rheostat) wall control. INSTALLATION INSTRUCTIONS CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER. 1. Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pressing the Light Switch after installation. 2. Press and hold the emitters SET key for about 3S in 30 seconds of turning the Receivers AC power ON, The receiver learn the emitters CODE and the emitter can remote the receiver.(FIG.1 / 2 / 3) 3. Your transmitter is ready for use after 2pc DC1.5V/ AAA, battery installation(FIG. 1) FIG. 1 FIG. 2 FIG. 3 FUNCTIONS OF TRANSMITTER 1 ON/OFF - Press and release immediately to turn on or off light. DIMMER - Press and hold to dim or brighten light to the desired level and release.

(Only when the dip switch was set on D dimmer setting) 2. FAN SPEEDPressing key s 1234

, it will control receiver FAN at speed 1~4 and OFF. 3. Pressing key

: Press and release immediately to set fan direction:

4.. Natural wind Function: Pressing key

, Fan will run in natural wind. 5.. Learning keys: Learning distance is no limition. Please press learning keysblack, Then receiver will remind that learning is finished. Only transmitter was learned can control receiver. 6. It has corresponding keys LED indicator, Pressing KEY, The LED indicator will flash. 7. key of color tempreture can be chosen to use. 8. Transmitter has learning key and toggle switch with 4 position (reserved). It has O/D switch. 9. Transmitter can be controlled by hand or you can place it in wall socket to control. To assure continued FCC compliance:

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. FCC ID2AQZU-18010 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC WARNING This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.

.CEILING FAN REMOTE CONTROLLER OPERATION AND INSTALLATION INSTRUCTIONS

(Please keep this instruction pamphlet.) IMPORTANT YOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHT KIT (IF ANY) TO ON POSITION BEFORE OPERATING REMOTE CONTROL. IMPORTANT POINTS TO REMEMBER:

1. Read and save these instructions. 2. Please note that all fixed wiring appliances should be installed by a qualified electrician. 3. The supply to the remote control receiver should be connected through a mains switch, i.e. existing wall switch. 4. Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan. 5. Install receiver into the ceiling fan canopy of the fan to ensure proper protection. 6. This unit is to be used for the control of ceiling fan and in an AC120V 60Hz power supply only. 7. Do not install in wet locations or immerse in water. 8. Do not pull on or cut leads shorter. 9. Do not drop or bump the unit. 10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place as this will damage the transmitter. Dispose of used battery properly, keep the battery out of reach of children. 11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable (rheostat) wall control. INSTALLATION INSTRUCTIONS CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER. 1. Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pressing the Light Switch after installation. 2. Press and hold the emitters SET key for about 3S in 30 seconds of turning the Receivers AC power ON, The receiver learn the emitters CODE and the emitter can remote the receiver.(FIG.1 / 2 / 3) 3. Your transmitter is ready for use after 2pc DC1.5V/ AAA, battery installation(FIG. 1) FIG. 1 FIG. 2 FIG. 3 FUNCTIONS OF TRANSMITTER 1 ON/OFF - Press and release immediately to turn on or off light. DIMMER - Press and hold to dim or brighten light to the desired level and release.

(Only when the dip switch was set on D dimmer setting) 2. FAN SPEEDPressing key s 123456 , it will control receiver FAN at speed 1~6 and OFF. 3. Pressing key

: Press and release immediately to set fan direction:

4.. Natural wind Function: Pressing key

, Fan will run in natural wind. 5.. Learning keys: Learning distance is no limition. Please press learning keysblack, Then receiver will remind that learning is finished. Only transmitter was learned can control receiver. 6. It has corresponding keys LED indicator, Pressing KEY, The LED indicator will flash. 7. key of color tempreture can be chosen to use. 8. Transmitter has learning key and toggle switch with 4 position (reserved). It has O/D switch. 9. Transmitter can be controlled by hand or you can place it in wall socket to control. To assure continued FCC compliance:

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. FCC ID2AQZU-18010 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC WARNING This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.

Mode el: TR330A-3 EXHIBI T 1 - PRO ODUCT L LABELIN NG FCC ID La abel Forma at FCC ID: 2 2AQZU-18 010 Proposed Specification silk-screened Proposed ns: Text is b d onto the EU black in colo UT or shall be r and justifie e affixed at a ed. Labels ar conspicuous re printed in location on t the EUT. indelible ink k on perman nent adhesivee Label Loca ation on EU UT FCC ID Label Lo cation Report No.: W WTH20X040 19312W RF Part 15.231a

Satellite Electronic(Zhong Shan)Ltd. No.8, Chuang Ye Road, Torch Development Zone, Zhongshan, Guangdong, China DATE: 2020-05-06 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AQZU-18010 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type File Name Schematics 2AQZU-18010 FCCID_ Schematics Block Diagram 2AQZU-18010_FCCID_BlockDiagram Operational Description 2AQZU-18010_FCCID_OperationalDescription The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Satellite Electronic(Zhong Shan)Ltd. sean zheng/Manager

Satellite Electronic(Zhong Shan)Ltd. No.8, Chuang Ye Road, Torch Development Zone, Zhongshan, Guangdong, China

(FCC ID : 2AQZU- 18010) POWER OF ATTORNEY DATE: 2020-05-06 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Satellite Electronic(Zhong Shan) Ltd. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Satellite Electronic(Zhong Shan)Ltd.

(sean zheng)

(Manager)