SB C&S.Corp. GLIDiC Sound Air SPT-7000 SB-WS73-MRTW manual Corresponding to the machine Bluetooth-enabled smart phones, tablets, and other Bluetooth devices with music playback and call capabilities Product Information using temperature range535 Earphones body Built-in battery: 3.7V 60mAh Bluetooth Spec.Version 5.0 Communication distanceabout 10minputClass 2*
ProfileA2DP, AVRCP, HFP, HSP Communication distanceSBC, AAC, apt XTM Corresponding codeSCMS-T Number of recorded devices: up to 7 units Dimensionsabout 23W19D24Hmm
: It different according to the environment in which it is used Charging case Built-in battery : 3.7V 460mAh Wire : micro USB (Type-B) cable Dimensionsabout 80W28D36Hmm Charging wire Wire: micro USB (Type-B) cable USB (Type - A) Connector length : about 30cm Music playback time / call time: about 8 hours When using a charging case Music playback time / call time: Approx. 20 hours charging Time: About 1 hour for earphone, 2 hours for case
* Varies depending on the usage environment. Action time First use Before using this product, be sure to read the "simple guide" and instructions. And please take good care of it after reading. About the book The average smartphone has download screens and steps. Due to the different machines used, please confirm in the instruction manual of your hand. The operation of the machine will be different depending on the OS system. The product can log in 7 machines at most. If you want to talk or listen to music with your headphones, you need to connect the appropriate devices. Login steps for logging in to more than two devices When the headset is standby, touch the sensor of the right headset for 5 seconds Made sure to operate with headphones on you ear Use of the product Log on to more machines Touch Sensor RightR The sound of login mode started .. Disconnect the product from the machine being connected Log in and connect to the corresponding machine Login /connect in the same order as the first. Please follow the wizard steps "register (pair) connections" to register and connect. When you want to switch connected devices, do the following The steps for switching connecting devices are as follows :
-1. When you unlinking a device, unlink the device according to the instructions
-2. When you want to link the device again, operate on the device to link LED display description
: To delete registration information (reset) After entering the login mode for 3 minutes, and the device is disconnected for 3-6 minutes, the headset will LED Charging case automatically timeout and power off The relationship between the charging case LED and Earphone Des charing Power on overtime Login ON Standby, no link Standby, link Working collect information Collect over logging R R w w w 2s w w W light 2 s 6 blinks light on slow flash of red light low flash of red light VVR /W light light 3flashes flashes white W light 5 sec R light 4 s The relationship between the charging case LED and the electricity Charging case the electricity electricity A little half much LED 1 LED light flashes 2 LED light flashes 3 LED light flashes If you are using a smartphone/phone and want to talk with your headset, check if the hands-free setup is in progress The steps vary depending on the device used If you are using the Soft Bank model, please scan the QR code below and check the steps on the Soft Bank Selection website. https://www.softbankselection.jp/bt/
FCC Statement Warning: Changes or modifications party responsible for compliance could void the users authority to operate the equipment. to this unit not expressly approved by the NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Shielded cables must be used with this unit to ensure compliance with the class B FCC limits. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference This device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
the device. Under
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Industry Canada regulations, Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire lesrisques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayon e quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autoris e aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. The device must not be co-located or operating in conjunction with any other antenna or transmitter The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. L'appareil a t valu pour rpondre aux exigences gnrales d'exposition aux radiofrquences. L'appareil peut tre utilis dans un tat d'exposition portable sans restriction. About the product information product name GLIDiC Sound Air SPT-7000 model NO. SB-WS73-MRTW case. The BQB logo, MIC ID and logo are printed on the Earphones. The product name and model number, FCC ID, IC and CE logo are printed on the charging This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause FCC ID: 2AO2PSPT-7000-R FCC ID: 2AO2PSPT-7000-L undesired operation. IC: 24766-SPT7000R IC: 24766-SPT7000L CANICES-3(B)NMB-3(B) Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si brouillage est susceptible d'en compromettre le fonctionnement. le ISEDC RF Exposure Statement:
The device compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance. This Class B digital apparatus complies with Canadian ICES-003. Aprs examen de ce matriel aux conformit aux limitesdintensit de champ RF, les utilisateurs peuvent sur lexposition aux radiofrquences et la conformit and compliance dacqurir les informations correspondantes Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. About the reuse of small rechargeable batteries This product uses a lithium ion battery. Lithium-ion batteries are a valuable resource that can be recycled. Because this product has a built-in lithium-ion battery, it cannot be thrown away as general garbage. When handling (reusing) according to the product life, etc., please contact the following. softbank customer service window Tel: 0800-111-2247 (toll free) Business hours: 10:00 ~ 19:00 (except for specific rest days) DC voltage DC voltage RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.