Passive Infrared Detector SB-5HNW Caution : It is not possible to repair for free that failures cause belongs to followings; not used by the instructions, careless use, fire/flood damage
/thunderbolt/robbery, wrong repair or remodeling, unusual power supply, externally damage. Installation Instructions 1. Description & Coverage and Range 10 3 1 4 5 8 11 9 1 2 3 4 5 6 7 8 9 10 11 12 7 12 2 6 2. Protection range Top view Side view No. 1 2 3 4 5 6 7 8 Description MAIN BODY COVER Main Body Cover TOP COVER Top Cover LED COVER LED Cover DECORATION Decoration BASE Base BOTTOM Bottom S/W Power S/W BATT COVER Battery Cover 9 S/W & S/W Sensor Area S/W & Sensitivity S/W 10 11 12 TAMPER S/W Tamper S/W S/W Registration S/W FOOT Foot 1 A R E A 3 AREA 1 AREA A E R A 3 2 AREA 4 AREA 3. Cautions on Installation Locate this sensor where intrusion can be made well. Please avoid to install where electric noise or heavy vibration can happen. Install where direct or reflected light doesnt affect sensor or sensor zone area. Do not install this sensor outside but inside only. 4. Installation 1) Turn Power S/W on. 2) Power is on, Red LED is flickering and warming up proceeds for 60sec. Power S/W Red LED 3) When warming up completes, click Registration S/W and register this sensor with wallpad. 4) Set up with DIP S/W. DIP S/W First click Registration S/W in point of contact transmitter and click Registration S/W in this sensor to register. 5) Restart this sensor.
< Caution>
- Restart takes 3 sec. 6) When power is on, Green LED is flickering and warming up proceeds for 60sec.
- In case of when registration completes and wallpad and communication are made normally. Power S/W Green LED In addition to sending an alarm for the transient, the device sends and receives a signal once only to synchronize. 5. Function DIP S/W 1 2 3 4 5 Sensor Area Set Up Sen-
sitivi-
ty 1) DIP S/W Set up Item DIP S/W Set up 1 2 3 4 5 Sensor Area Set up sensitivity 2) Tumble Check function ON OFF ON OFF ON OFF ON OFF ON OFF 1 AREA Alert 1 AREA Clear 2 AREA Alert 2 AREA Clear 3 AREA Alert 3 AREA Clear 4 AREA Alert 4 AREA Clear Slow Sensor Fast Sensor Remark Default Default Default Default Default Tamper S/W Alarm when sensor tumbles or falls off 3) When power is on and battery has low power, boozer inside keeps beeping repeatedly. 4) In addition to sending an alarm for the transient, the device sends and receives a signal once only to synchronize 6. Troubleshooting Problem Cause Measure Power is on, warming up
(LED is not flickering). DC 3V Alkaline Battery power is out. DC 3V Alkaline Battery power is in. This doesnt sensor Human body. Problem with point of contact-
transmitter circuit in wall-pad Consult A/S Delay times(2mins) extends since first sensing or inside circuit problem Consult A/S Cover is dirty Clean with smooth cloth. This malfunctions or doesnt sense anything. Direct light touches sensor Adjust location and block direct light. Sensor doesnt sense normally. Adjust sense range/zone. 7. Specification & Dimension Model No. Method Sense range/zone SB-5HNW Passive Infrared motion detecting Solid Alert Type Detect Range: 5m / 360 Zone dimension 12pair (24 Zone) x 4 (96 Zone) Power supply DC3V (Alkaline-Battery 1.5V_AA x 2EA) Consume current Less than 60 (less than 30 when alarming) Green When warming up, sensor is flickering for 60sec.
(in case of sensor is registered into wall-pad) LED Red Temperature Install place Material Dimension Weight When warming up, sensor is flickering for 60sec.
(in case of sensor is not registered into wall-pad) When sensing, light is on(about 2sec.)
-20 ~ +60 indoor Cover, Base: ABS, Lens: PE 103.4 x 193.9mm 300g Function 360 sensing, set up 4 sense Area, set up sensitivity NOTE : specification is able to be changed without notice to improve function. Security&Best Co., Ltd 430-821 #1005, Dojeong B/D, 548-6, Anyang8-Dong, Manan-Gu, Anyang-City, Gyeonggi-Do Tel : +82-31-341-8513~4,8247 / Fax : +82-31-341-8669 www.secuandb.com / e-mail : ljw@secuandb.com Copyright 2011 KMT design REV.0 Radio Post Company LTD FCC Compliance Statement. Do Not. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void users authority to operate the equipment.