AVERTISSEMENT 7087A-2WA1000SSL2 7087A-2WA1000SSL2 7087A-2WA1000SSL 7087A-1WR1040SSL IC ID (International seulement) VA5JA1000-2WSSL VA5JA1000-2WSSL VA5JR1040-2WSSL VA5JR1040-1WSSL FCC ID (US seulement) MA1000-2WAY2 MA1000-1WAY MR1040-2WAY MR1040-1WAY Tlcommande & Antenne Manuel de lutilisateur R emote & Antenna FCC ID Number (US Only) IC ID Number (International Only) MR 1040-1WAY MR 1040-2WAY MA1000-1WAY MA1000-2WAY 2 VA5J R 1040-1WS S L VA5J R 1040-2WS S L VA5J A1000-2WS S L VA5J A1000-2WS S L 7087A-1WR 1040S S L 7087A-2WA1000S S L 7087A-2WA1000S S L2 7087A-2WA1000S S L2 T a b l e o f C o n t e n t s FCC Radiation Exposure Statement for integral antenna module:
The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. FCC Radiation Exposure Statement for car remote control:
The antenna(s) used for this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter within a host device, except in accordance with FCC multi-transmitter product procedures. End-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. Introduction This is a state-of-the-art remote car starter system. The system is packed with advanced features such as priority access to the drivers door (commodity feature). With its many advanced functions, this product will act as a remote starting device and security system.
Button(s) 0.5 Second 2.0 Second Using the remote control
Page 4
PANIC UNLOCK Trunk Release LOCK UNLOCK Car Check Remote START / STOP Valet Mode ON / OFF Passive Arming ON / OFF Time Start ON / OFF Low Battery Start ON / OFF
5 Page Vehicle Presets Remote Starting your Vehicle
Certain vehicles require windshield wipers and / or headlights circuits to become active while running under remote start. When leaving the vehicle, you must ensure that the windshield wipers and headlights switches are OFF. Leaving the windshield wipers ON, it could damage wipers when remote engine starts and the headlight switch ON on certain types of vehicles could cause them to remain ON even after remote starter shutdown, resulting in a dead battery.
1. You may use a coin to separate the top and bottom section of the transmitters case. 2. 2-Way Transmitter - When inserting the battery (CR2450/620mAH), ensure the + terminal is on TOP, as illustrated. 3. 1-Way transmitter - Insert the 2 batteries in the poly bag (CR2016 x 2EA). NOTE: When you press a button and the 2-way transmitter LED changes from blue to RED, it is time to replace the battery. Page 6 For the 2-way remote:
1. Tap the button. The remote will beep once and display the icon. Then, tap the button within 3 seconds. The remote will beep once and display the icon. 2. Approximately 5 seconds later, the remote will confirm the remote starters activation by beeping three times and displaying the icon, and scrolls through the LED icons. 3. To stop the engine, tap the button for a 1/2 second. For the 1-way remote:
1. Tap the button. Then, tap the button within 3 seconds. 2. To stop the engine, tap the button for a 1/2 second. If your vehicle does not start at the first attempt, the system will shut down, wait a few seconds and try to start the engine again. There will be 3 start attempts before the system gives up.
With the vehicle running remotely, tap the button to disarm the immobilizer and/or the OEM alarm and unlock the doors. Enter the vehicle and do the following:
1. Turn the ignition key to the IGNITION ON (RUN) position. (Do not turn the key to the START position while the engine is running. This would cause the starter motor to reengage.) 2. Press the brake pedal to disengage the remote starter unit.
(Once the key is in the IGNITION ON position, vehicle is ready to run after pressing the brake pedal.) Note: In remote engine start status, engine activation will be off for the following reasons.
- You press the brake pedal while the key was not placed on IGNITION ON position.
- You did not activate the engine within 30 seconds after opening the door. 7 Page Remote Starter Features
When your vehicle is in Valet Mode, the remote starter functions are disabled. If the vehicle needs to be serviced, or if you park it indoors, the Valet Mode will prevent the engine from being remote-started by accident. Any of the following features will put your remote car starter into Valet Mode:
Ignition Valet:
This feature allows you to put your system into Valet Mode by using the ignition key. Remote Valet:
This feature allows you to put your system into Valet Mode by using the transmitter. To put the system into Valet Mode:
Ignition Valet:
Insert your key into the ignition and turn the ignition on, then off (between ACC and ON), five times within 10 seconds. Remote Valet:
Tap the and buttons simultaneously for a 1/2 second. The remote will beep once and display the and icons (2-way), and the parking lights of vehicle flash once. To take the system out of Valet Mode:
Ignition Valet:
Insert your key into the ignition and turn the ignition on, then off (between ACC and ON), five times within 10 seconds. Remote Valet:
Tap the and buttons simultaneously for a 1/2 second. The remote will beep twice and display the and icons (2-way), and the parking lights of vehicle flash twice. To verify whether the system is in Valet Mode using the 2-way remote:
If the system is in Valet mode, buzzer sounds shortly when the or button is pressed. In an emergency situation, you can activate the panic mode by pressing and holding the button for more than 2 seconds, then the LED on the remote scrolls to the mute status. The parking lights start flashing and the horn starts honking. If the vehicle is already started remotely, the engine will shutdown automatically before setting off the horn. You can stop the horn by pressing either the button or the button. The panic mode can be stopped by activating the Valet mode (previous section). Nate: Panic Mode will automatically shut down after 30 seconds. Advanced Features
The Remote Car Starter was designed with flexibility and OEM integration in mind. With its programmable options, this unit can virtually control nearly any electrical system in your vehicle. Caution: The programming of your system should be left to a Hyundai professional. Changing any one of the settings may affect the operation of your Remote Car Starter. Page 8 9 Page Remote Starter Features
You can turn this feature on and off by pressing the and buttons for a 1/2 second. If Time start is set, the vehicle will start by itself at the preset time every 24 hours. If low battery start was already set in advance and time start is set, low battery start is automatically cancelled.
You can turn this feature on and off by pressing the and buttons for more than 2 seconds. The vehicle will start at the same time even if the battery voltage falls below the set value. If Time start was already set in advance and low battery start is set, Time start is automatically cancelled. Note: If the vehicles battery voltage is too low, Time start and Low battery start will not be activated.
To UNLOCK the doors and DISARM the system:
Tap the button for 1/2 second.
(2-way) The remote will beep twice and display the icon to confirm unlocking of the doors. Note: In Arming status, the remote detects the door unlocking. To LOCK the doors and ARM the system:
Tap the button for 1/2 seconds.
(2-way) The remote will beep once and display the icon to confirm locking of the doors. Note: If you press the unlock button once, the vehicle is disarmed and only the driver side door is unlocked. If you press the unlock button again within 5 secondes, all doors will unlock. Page 10
Your Remote Car Starter can be programmed to run the engine for 3, 8 or 15 minutes (3 minutes by default) Option Seting Function
#1 1-3 Feature Remote Start Run time Default (I) 3 Min Setting Optional (II) 8 Min Optional (III) 15 Min Option Setting Condition : Driver's door must be physically open. + Key out of the Vehicle. + Ignition OFF. 1. For example, option 1-3 Remote Start Runtime 1) Press button for 2 seconds simultaneously Vehicle chirps 1 time and light flashes 1 time -> ready to enter option change mode.(Within 3-4 seconds) 2) Option Change Mode Select the option number and tap button as much as the option number you selected For Remote Start Run option(1-3), Tap button three(3) times as follows:
Tap button, vehicle chirps 1 time & light flashing 1 time -> This is 1st time. Tap button, vehicle chirps 1 time & light flashing 1 time -> This is 2nd time. Tap button, vehicle chirps 1 time & light flashing 1 time -> This is 3rd time. You can go to the next stage only after you confirm the chirping & flashing every time. -> wait 4 seconds 3) After 4 seconds, vehicle will chirp 3 times & light flashing 3 times simultaneously
-> This reaction is confirming the user selected option # 1-3 "Remote Start Runtime"
4) Select the running time:
If you want to set at "8 Min - Option(II)", Tap button. Vehicle finally chirps 2 times & light flashing 2 times
-> This is confirming the user selected default option(II) If you want to set at "15 Min - Option(III)", Tap button. Vehicle finally chirps 3 times & light flashing 3 times
-> This is confirming the user selected default option(III) 2. To RESET to Original state Default(l) Repeat Above Step 1 & 2, then Press the button three(3) times, option is reset to Default(l) 11 Page To check the amount of runtime remaining (2-way only):
If you press button and then press button within 3 seconds, the engine is remote started and if successfully done, the remote receives a signal and displays the remaining time with an icon every 5 seconds. Display Remaining Time with Icon Total Remaining Time For 8 minutes 8 minutes 6 minutes 4 minute 2 minute For 15 minutes 15 minutes 12 minutes 8 minute 4 minute For 3 minutes 3 minutes 2 minutes 1 minute 1/2 minute
You can check your car by pressing the button for a 1/2 second. Troubleshooting Many factors may affect the operating range of the transmitter. Some of these are:
The condition of the battery in the transmitter. The operating environment (for example: downtown radio-frequency noise, airports, cellular phone towers). Metal: any type of metal will affect operating range. This includes the vehicle itself. The shape of the vehicle can affect range as well (vans in general have less range). The shape of the roof and A-pillars bring about considerable radio-frequency deflection(in this case, the signal from the remote control).As a result, the direction in which the vehicle is facing in relation to the remote control can affect the range. Straight on (standing in front of the vehicle) generally gives you the greatest range; the second best performance if from the back. Using the remote control from either side of the vehicle will usually give the lowest range. The range will be significantly lower in a crowded parking lot than in open space. Always hold the transmitter high, approximately at shoulder height. Lock/Unlock Door/Hood/Trunk Lock Unlock Unlock Triggered Three times BEEP Once Twice ICON DISPLAY Note:
If engine is running, icon is additionally displayed and buzzer beeps.
You can turn this feature on and off by pressing the and buttons for a 1/2 second. With passive mode on, your vehicle will lock and arm 30 seconds after the door is opened and closed. The parking lights will flash and/or siren will chirp every 10 seconds for up to 30 seconds. Page 12 13 Page 8102REMOK000200 Version 1.1 NUMRO DU CENTRE D'APPELS ARS :
1-855-225-7344 ARS CALL CENTER NUMBER 1-855-225-7344 Version 1.1 8102REMOH000200 13 Page Tenez toujours la tlcommande leve, la hauteur des paules environ. La porte sera notamment rduite dans un parc de stationnement achaland. ou de l'autre du vhicule donnera la plus courte porte. habituellement la plus longue porte. La deuxime meilleure position est de l'arrire. Utiliser la tlcommande d'un ct du vhicule par rapport la tlcommande peut avoir un effet sur la porte. Droit devant le vhicule donne La forme du toit et des piliers peut affecter les radiofrquences (soit le signal de la tlcommande). Ainsi, l'orientation La forme du vhicule peut influencer la porte (porte rduite sur les fourgonnettes). Mtal : tout type de mtal peut affecter la porte, y compris le vhicule lui-mme.
(exemple : radiofrquences au centre-ville, aroports, tours de tlphonie cellulaire, etc.) L'environnement de fonctionnement L'tat de la pile du transmetteur. une sonorite et la tlcommande mettra icne sera galement affiche Si le moteur est en marche, son Note:
Dclench Trois fois Deux fois Une fois IC NE AFFICHE BIP COFFRE PORTE/CAPOT/
Page 12 Dverrouillage Dverrouillage Verrouillage Dverrouillage Verrouillage/
Vous pouvez vrifier le statut du vhicule en appuyant sur le pendant 1/2 seconde.
4 minutes 8 minutes 12 minutes 15 minutes 2 minutes 4 minutes 6 minutes 8 minutes 1/2 minute 1 minute 2 minutes 3 minutes Rgl sur 15 minutes Rgl sur 8 minutes Temps restant total Rgl sur 3 minutes Plusieurs facteurs peuvent affecter la porte de la tlcommande, savoir :
Icne de temps restant Dpistage des problmes Les feux de stationnement clignotent et/ou la sirne met un son toutes les 10 secondes jusqu' 30 secondes. En mode passif, le vhicule se verrouille et s'arme dans les 30 secondes aprs qu'une porte ait t ouverte et referme. Vous pouvez mettre la fonction en ou hors circuit en appuyant sur et pendant 1/2 seconde.
reoit un signal et affiche le temps restant toutes les cinq secondes. Si vous appuyez sur puis sur dans les 3 secondes, le dmarrage distance est activ et s'il russit, la tlcommande 3. Pour vrifier le temps restant (bidirectionnel seulement):
Rptez les tapes 1&2, puis appuyer sur 3 fois. Les options sont reprogrammes (Default I) 2. Pour reprogrammer les options originales (Default I)
-> Cette raction confirme la slection de loption (III) Pour slection de 15 minutes, appuyer sur , le vhicule met 3 tonalits et 3 clignotements des feux. 11 Page
-> Cette raction confirme la slection de loption (II) Pour slection de 8 minutes, appuyer sur , le vhicule met 2 tonalits et 2 clignotements des feux 4) Slection du temps de fonctionnement du moteur:
-> Cette raction confirme la slection doption 1-2 de la dure de fonctionnement du moteur. 3) Aprs les 4 secondes, le vhicule met 2 tonalits et 2 clignotements des feux simultanment. Vous pouvez procder la prochaine tape seulement aprs confirmation de chacune des tapes prcdentes.
, le vhicule met une tonalit et un clignotement des feux. (Troisime tape accomplie)
, le vhicule met une tonalit et un clignotement des feux. (Deuxime tape accomplie)
, le vhicule met une tonalit et un clignotement des feux. (Premire tape accomplie) Appuyer sur le bouton Appuyer sur le bouton Appuyer sur le bouton 3 fois de la faon suivante ;
Pour loption de dure de fonctionnement du moteur (1-3), appuyer sur le bouton 2) Option de changement de mode:
1 tonalit et 1 clignotement des lumires -> Le systme est prt pour le changement des options dans les 3-4 prochaines secondes. 1) Appuyer sur les boutons simultanment pendant 2 secondes. 1. EXEMPLE POUR OPTION 1-3
(la porte du conducteur doit tre ouverte + la cl hors du vhicule + le contact la position OFF.) CONDITIONS DE RGLAGE 15 min 8 min Option (III) dfaut (II) 3 min dfaut (I) Rglage moteur avec dmarrage distance Dure de fonctionnement du Caractristique 1-3
#1 Rglagedes options Le dmarreur distance peut tre rgl pour maintenirle moteur en marche pendant 3, 8 ou 15 minutes (3 minutes par dfaut) Page 10 dverrouille. Appuyez sur le bouton une deuxime fois dans les 5 secondes afin de dverrouiller toutes les portes. Note : Si vous appuyez une fois sur le bouton de dverrouillage, le vhicule est dsarm et seule la porte du conducteur se
(Bidirectionnel) La tlcommande met une tonalit et affiche confirmant le verrouillage des portes. Appuyez sur pendant 1/2 seconde. VERROUILLER les portes et ARMER lantivol :
Note :Au mode arm, la tlcommande dtecte le dverrouillage des portes.
(Bidirectionnelle) La tlcommande met une tonalit et affiche confirmant le dverrouillage des portes. Appuyez sur pendant 1/2 seconde. DVERROUILLER les portes et DSARMER lantivol ;
Note : Si la tension de la batterie chute, ni le dmarrage minut ni le dmarrage sur batterie faible ne sera fonctionnel. dmarrage minut tait rgl avant le dmarrage sur batterie faible, le dmarrage minut est automatiquement annul. Le vhicule dmarre automatiquement chaque heure si la tension de la batterie s'abaisse sous la valeur rgle. Si le Vous pouvez activer et dsactiver la fonction en appuyant sur et pendant 2 secondes
automatiquement annul. Si le dmarrage sur batterie faible tait dj rgl et que vous rglez un dmarrage minut, le dmarrage sur batterie faible est Si le dmarrage minut est rgl, le vhicule dmarre l'heure tablie, toutes les 24 heures. Vous pouvez activer et dsactiver cette fonction en appuyant sur et pendant 1/2 seconde.
9 Page Quand le MODE VALET est en circuit, il y aura une tonalit mise a lappuie des boutons de ou . Pour vrifier si le systme est en mode Valet l'aide de la tlcommande bidirectionnelle :
Page 8 modification aux rglages affectera le fonctionnement du dmarreur distance. Attention :La programmation du dmarreur distance devrait tre confie un professionnel Hyundai. Toute options programmables, lunit peut contrler pratiquement tout systme lectrique du vhicule. Le dmarreur distance est conu pour tre flexible et intgrable aux systmes dorigine des constructeurs. Avec ses
Fonctions avances Note : Le mode Alarme s'teint automatiquement aprs 30 secondes. Valet (section prcdente). Vous pouvez arrter le klaxon en appuyant sur ou . En outre, le mode Alarme peut tre arrt en activant le mode Si le vhicule a t dmarr distance, le moteur steind automatiquement avant de dclencher le klaxon. clignotent et le klaxon retentit. ce que le klaxon retentisse. Le voyant DEL de la tlcommande passe au statut muet. Les feux de stationnement En situation durgence, vous pouvez activer le mode < Alarme > en enfonant le bouton pendant 2 secondes jusqu Appuyez sur et simultanment pendant 1/2 seconde . La tlcommande met une tonalit et affiche 5 reprises en 10 secondes ou moins, puis la position OFF. Insrez la cl dans le contactdallumage et passez de la position ON la position OFF (entre ACC et ON) et (bidirectionnel), les feux de stationnement clignotent une fois. Valet par le contactdallumage :
Pour dsactiver le mode Valet :
Appuyez sur et simultanment pendant 1/2 seconde. La tlcommande met une tonalit et affiche et (bidirectionnel), les feux de stationnement clignotent une fois. 5 reprises en 10 secondes ou moins, puis la position OFF. Insrez la cl dans le contactdallumage et passez de la position ON la position OFF (entre ACC et ON) Valet avec la tlcommande :
Valet par le contactdallumage :
Pour activer le mode Valet :
Cette fonction permet de passer en mode Valet l'aide de la tlcommande. Cette fonction permet de passer en mode Valet l'aide de la cl de contact. Valet distance:
Valet par le contact d'allumage :
Chacune des fonctions suivantes vous permettra de faire passer votre systme de dmarrage distance en mode Valet laiss en rparation, ou si vous le stationnez lintrieur, le mode Valet prviendra les dmarrages distance accidentels. Lorsque le systme est en mode Valet, les fonctions de la tlcommande sont alors dsactives. Si le vhicule doit tre
CARACTRISTIQUES DU DMARREUR DISTANCE 7 Page
- Si vous n'activez pas le fonctionnement normal du moteur dans les 30 secondes aprs l'ouverture de la portire.
- Si vous appuyez sur la pdale de frein alors que la cl de contact n'est en position de marche (ON). Note : Au statut de dmarrage distance, le dmarrage du moteur sera annul dans les cas suivants :
marche (ON) et que le moteur est dmarr, vous pourrez conduire le vhicule aprs avoir appuy sur les freins.) 2. Appuyez sur la pdale de frein pour dsengager le dmarreur distance. (Alors que le contact est la position de
(START)alors que le moteur est en marche. Ceci risquerait d'activer nouveau le dmarreur.) 1. Tournez la cl de contact en position de marche (ON ou RUN). (Ne tournez pas la cl jusqu' la position de dmarrage dverrouiller les portes. Entrez dans le vhicule et procdez comme suit :
Si le vhicule a t mis en marche distance, appuyez sur pour dsarmer l'antidmarrage et/ou l'antivol et
en cas dchecs rpts. tentera nouveau de faire dmarrer le moteur. Le systme effectuera trois tentatives de dmarrage avant dabandonner Si le vhicule ne dmarre pas du premier coup, le systme interrompra le dmarrage,attendra quelques secondes et 2. Pour couper le moteur, appuyez sur pendant 1/2 seconde. 1. Appuyez sur . Puis, appuyez sur dans les 3 secondes. Tlcommande unidirectionnelle :
3. Pour couper le moteur, appuyez sur pendant 1/2 seconde. affichant et faisant dfiler les icnes DEL. 2. Aprs environ 5 secondes, la tlcommande confirme lactivation du dmarreur distance en mettant trois tonalits, La tlcommande met une tonalit et affiche . 1. Appuyez sur . La tlcommande met une tonalit et affiche . Puis, appuyez sur pendant 3 secondes. Tlcommande bidirectionnelle :
Page 6 Pile au lithium la pile (CR2450). bleu au ROUGE quand vous appuyez sur un bouton, il est temps de changer NOTE : Si la DEL bicolore de la tlcommande bidirectionnelle passe du 3. Tlcommande unidirectionnelle - Insrez 2 piles (CR2016) dans le botier en poly. orient vers le HAUT. 2.Tlcommande bidirectionnelle - Quand vous insrez la pile, assurez-vous que le ct < + > (CR2450/620 mAh) est 1. Vous pouvez sparer les deux moitis de la tlcommande avec une pice de monnaie.
distance, ce qui mettrait la batterie plat. fonction (ON), vous risquez que les phares restent allums mme aprs avoir coup le moteur vhicule, assurez-vous que les essuie-glaces et les phares sont hors fonction (OFF). Si vous laissez les phares en Sur certains vhicules, essuie-glaces et/ou les phares sont activs lors du dmarrage distance. Lorsque vous quittez le
Dmarrage distance du vhicule Prrglage des accessoires 5 Page sur batterie faible Mise en/hors fonction du dmarrage Mise en/hors circuit du dmarrage minut
[En circuit = 1 bip / Hons circuit = 2 bip]
Mise en/hors circuit de larmement passif Mise en/hors circuit de larmement passif Mise en/hors circuit du mode Valet Marche / Arrt distance Ouverture du coffre Dverrouiller Alarme 2.0 secondes Statut Dverrouiller Verrouiller 0.5 seconde Tlcommande unidirectionnelle Tlcommande bidirectionnelle Page 4 pendant 1/2 seconde. sur le bouton MARCHE/ARRT Pour couper le moteur, appuyez MARCHE/ARRT. 3 secondes, sur VERROUILLER puis, dans les distance, appuyez sur Remarque: Pour un dmarrage distance du moteur Dmarrage ou coupure MARCHE / ARRT :
STATUT / COFFRE DVERROUILLER VERROUILLER/ALARME DEL 2 couleurs, 1 icnes Tlcommande unidirectionnelle DEL 2 couleurs, 4 icnes Tlcommande bidirectionnelle
Utilisation de la tlcommande Bouton (s)
Avec ses fonctions avances, ce dispositif agit comme dmarreur distance et systme de scurit. porte du conducteur (fonction de commodit). Ce dmarreur distance est un systme avanc offrantdes caractristiques uniques comme l'accs en priorit la Introduction
Mode Panic Mode Valet
Conduite aprs le dmarrage distance Dmarrage distance
autorises apportes l'appareil. REMARQUE :Le fabricant ne peut tretenu responsable du brouillage radiolectrique caus par des modifications non ncessaire pour assurer une communication efficace. gain dantenne de faon ce quela puissance isotrope rayonne quivalente (PIRE) ne dpasse pas ce qui est Pour rduire le brouillage radiolectrique qui risque daffecter dautres utilisateurs, il est important de choisir le type et le 2) lappareil doit accepter toute interfrence, mme celles qui pourraientnuire son fonctionnement. 1) lappareil ne doit causer aucune interfrence nuisible;
L'utilisationde cet appareil est soumise aux deux conditions suivantes :
AVIS D'INDUSTRIE CANADA LUTILISATEUR :
Remplacement de la pile de la tlcommande Essuie-glaceset phares
Fonction des boutons Description de la tlcommande
Mise en/hors circuit de l'armement passif Vrification du vhicule Dure de fonctionnement du moteur Tlverrouillage des portes Dmarrage sur batterie faible Dmarrage minut
Table des matires