FT-EZGO Quick Setup Card Thank you for purchasing FT-EZGO system from Firstech. This system will automatically unlock and remotely lock and unlock your vehicle. This guide will help you properly setup your FT-EZGO. If you have any questions please contact your place of purchase or usat 888-820-3690 Monday through Friday 8 AM to 5 PM PST. Your FT-EZGO is designed to operate with a Firstech compatible alarm, remote start, alarm and remote start combo, and Drone DR-2000. FT-EZGO system includes 1 remote (EZ100-R) and 1 antenna (ANT-RFID). Also note you can only use 2 other remotes plus your EZ100-R on your system. Your system has between 5 and 10 feet of range before your vehicle will Unlock/Disarm. FT-EZGO will wait a minimum of 15 seconds before it will initiate the automatic unlock/disarm. Duration Function Siren Chirps and/or Parking Light Flashes Half Second Tap Then Hold 8 Seconds Locks/Arms and Unlocks/Disarms your vehicle. Trunk Pop Turns Automatic Unlock on and off. 1 - Lock/Arm 2 - Unlock/Disarm 2 - Chirps and/or Flashes 1 - On 2 - Off Replacing your EZ100-R Battery Your remote requires 1 CR2032 battery. It can be replaced by carefully prying apart your remote case near where the keychain loop is. This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following conditions:
(1) this device may not cause interference, and
(2) this devicemust accept any interference, including interference that may cause undesired operation of the device. CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this device. Carte de Mise en Route Rapidu FT-EZGO Nous vous remercions davoir achet le systme FT-EZGO de Firstech. Ce systme dverrouillera automatiquement et verrouillera et dverrouillera distance votre vhicule. Ce guide vous aidera programmer correctement votre FT-EZGO. Si vous avez des questions, contactez votre dtaillant ou contactez-nous au 888-820-3690 du lundi au vendredi de 8h00 17h00, heure normale du Pacifique. Votre FT-EZGO a t conu pour fonctionner avec une alarme, un dmarreur distance, un combo alarme et dmarreur distance compatibles avec Firstech et avec Drone DR-2000. Le systme FT-EZGO inclut 1 tlcommande (EZ100-R) et 1 antenne (ANT-RFID). Veuillez aussi noter que vous pouvez utiliser seulement 2 tlcommandes additionnelles en plus de votre EZ100-R sur votre systme. Votre systme a entre 5 et 10 pieds de porte avant le dverrouillage/dsactivation de votre vhicule. FT-EZGO attendra un minimum de 15 secondes avant dinitier le dverrouillage/dsactivation automatique. Dure Fonction Verrouille/active et d verrouille/dsactive votre v hicule. Bips de la sirne et/ou clignotements des feux de stationnement 1 - Verrouille/active 2 - dverrouille/dsactive Ouvre le coffre 2 - Bips et/ou clignotements Active et dsactive le dverrouillage automatique 1 - Active 2 - Dsactive Demi-seconde Pressez et ensuite tenez 8 Seconds Remplacement de la batterie de votre EZ100-R Votre contrle distance ncessite 1 batterie CR2032. Vous pouvez la remplacer en ouvrant soigneusement la boite de la tlcommande prs de la boucle pour le porte-cl. Ce dispositif est conforme avec la partie 15 des rglements FCC. Lopration est assujettie aux conditions suivantes :
(1) Ce dispositif ne devrait pas causer des interfrences nuisibles.
(2) Ce dispositif devrait accepter les interfrences reues incluant celles qui pourraient occasionner des oprations indsirab Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. AVERTISSEMENT:Des changements ou modifications non-expressment approuvs par les parties responsables de cette conformit peuvent annuler lautorisation doprer ce dispositif. FT-EZGO Installer Setup Card The FT-EZGO from Firstech will unlock/disarm the vehicle when in range. It will also lock/arm and unlock/disarm the vehicle when you press the button on the EZ100-R. Installing The FT-EZGO Step 1 : Flash your CM6 Series control module for FT-EZGO compatible firmware. Step 2 : Set Option 1-14 to Setting 3 Step 3 : Connect included 6 Pin to 6 Pin with Ground Wire to control module. If connecting to a 4 Pin to 4 Pin antenna, use the included 6 Pin to 4 Pin adapter. Step 4 : Connect the ground wire from the included 6 Pin to 6 Pin cable to vehicles ground. Warning: Failure to connect this wire WILL result in damage to your FT-EZGO antenna
(ANT-RFID). Step 5 : Connect your antenna to the ANT-RFID. This is the blue 6 Pin port. If you have a 4 Pin antenna cable, use the included 4 Pin to 6 Pin adapter. Step 6 : Find a spot to mount your ANT-RFID on the windshield. This is recommended for optimum range. For more specific mounting location information visit us at www.firstechonline.com under the Authorized Tech section document titled:
FT-EZGO Recommended Mounting Locations. Step 7 : Program your EZ100-R and additional RF Kit remotes to the control module.
(Maximum 3 Remotes including EZ100-R). You are now ready to test your FT-EZGO system. Testing The FT-EZGO Step 1 : Turn the auto unlock feature by holding the button on the EZ100-R for at least 8 seconds. You will get one parking light flash and/or siren chirp. Hold the button again for at least 8 seconds and you will get two parking light flashes and/or chirps showing that the auto unlock feature is off. Step 2 : Arm/Lock the vehicle and wait at least 15 seconds. Step 3 : Walk up to the vehicle and it will automatically unlock/disarm. Carte de programmation pour linstallation du FT-EZGO Le FT-EZGO de Firstech dverrouillera/dsactivera le vhicule quand il est porte. Aussi, il verrouillera/activera le vhicule quand vous pressez le bouton sur la EZ100-R. Installation du FT-EZGO tape 1 : Cherchez dans votre module de contrle de la srie CM6 pour un micro logiciel compatible avec le FT-EZGO. tape 2 : Ajustez loption 1-14 au rglage 3. tape 3 : Connectez le 6 connecteurs 6 connecteurs inclus avec connexion terre au module de contrle. Si vous le connectez une antenne 4 connecteurs 4 connecteurs, utilisez ladaptateur inclus, 6 connecteurs 4 connecteurs. tape 4 : Connectez le fil terre du cble 6 connecteurs 6 connecteurs inclus la masse du vhicule. Avertissement : Ne pas connecter ce fil ENTRANERA des dommages lantenne (ANT-RFID) de votre FT-EZGO. tape 5 : Connecter votre antenne lANT-RFID. Ceci est le port bleu 6 connecteurs. Si vous avez un cble dantenne 4 connecteurs, utilisez ladaptateur inclus de 4 connecteurs 6 connecteurs. tape 6 : Trouvez une place sur le pare-brise pour monter votre ANT-RFID. Ceci est recommand pour avoir une porte optimale. Pour avoir plus dinformation sur des emplacements spcifiques, visitez www.firstechonline.com; dans la section vous trouverez un document intitul: FT-EZGO Recommended Authorized Tech , Mounting Locations. tape 7 : Programmez votre EZ100-R et les tlcommandes additionnelles RF Kit au module de contrle (Maximum de 3 tlcommandes en incluant la EZ100-R). Vous tes prt maintenant pour tester votre systme FT-EZGO. Test du FT-EZGO tape 1 : Activez la fonction de dverrouillage automatique en tenant press le bouton sur le EZ100-R pendant au moins 8 secondes. Vous aurez un clignotement des feux de stationnement ou/et un bip de la sirne. Tenez encore le bouton pendant au moins 8 secondes et vous obtiendrez deux clignotements des feux de stationnement et/ou bips pour montrer que la fonction de dverrouillage automatique est dsactive. tape 2 : Activez/verrouillez le vhicule et attendez au moins 15 secondes. tape 3 : Approchez-vous du vhicule et il se dverrouillera/dsactivera automatiquement.