all | frequencies |
|
|
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|---|---|
manuals | photos | labels |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Product range description | Users Manual | 1.89 MiB | ||||
1 |
|
Quick start guide | Users Manual | 3.11 MiB | ||||
1 |
|
Internal Photos | Internal Photos | 5.20 MiB | ||||
1 |
|
External photos | External Photos | 2.43 MiB | ||||
1 |
|
Label | ID Label/Location Info | 369.84 KiB | ||||
1 |
|
Label placement photo | ID Label/Location Info | 805.71 KiB | ||||
1 |
|
Cover Letter | Cover Letter(s) | 39.65 KiB | ||||
1 |
|
Request for Confidentiality | Cover Letter(s) | 67.43 KiB | ||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | Product range description | Users Manual | 1.89 MiB |
Product Specification AP-2010 Last change: 27.03.2017 Product Specification AP-2010 1 Introduction 1.1 Key Features 1.2 Destination countries 1.3 Scope of delivery 2 Barcode Information 2.1 Serial Number 3 Mechanical Characteristics 3.1 Mechanical Dimensions 3.2 Front, Side and Top View 3.3 Upper Surface 3.4 Side View 3.5 Rear View 4 Mounting 4.1 Audience 4.2 General Instructions 4.3 Instructions for the Mounting Location 4.4 Approachability 4.5 Screw of the Antenna 4.6 Metal Bracket for Mounting on Wall, Ceiling or T-Mounting Rail 4.7 Mounting on Wall or Ceiling 5 Electrical Specifications 5.1 Used Channels 5.2 Difference WiFi and ESL protocol 5.3 Cabel Specifications 5.4 Power Supply Specifications 5.5 Pinout RJ45 Ethernet 6 Electrical & RF Characteristics 6.1 General Technical characteristics 6.2 Power and Current Consumption 6.3 General Specifications 7 Environmental 7.1 Humidity and Operating Conditions 4 4 4 4 5 5 7 7 7 8 8 9 10 10 10 10 11 11 12 12 15 15 15 15 16 16 17 17 17 17 19 19 Page 2 of 27 Product Specification AP-2010 7.2 Storage Conditions 7.3 Cleaning Instructions 8 Packing 8.1 Packing Dimensions 8.2 Illustrations 8.3 Palletization 9 Certifications 9.1 Types 9.2 Overview 9.3 Applied Standards 9.4 Declaration 10 Problems which requiring maintenance or replacement of the AP-2010 11 Intended Use 12 Improper Use 13 Warranty 19 19 20 20 20 21 22 22 22 22 22 24 25 26 27 Page 3 of 27 Product Specification AP-2010 1 Introduction The Access Point AP-2010 by imagotag is a network device similar to WLAN access points that is required for communication with the imagotag electronic shelf labels (transmits price information to the labels). Up to 10 000 labels can be managed per access point and the self-organizing network allows automatic roaming of labels without manual handling. The high transmission rate of the 2.4 GHz wireless technology and the intelligent task scheduling enables fast and secure updates on imago G1 labels of all sizes. This document is the technical specification of the Access Point AP-2010. In the USA and Canada the AP-2010 usa/canada bundle incl. antenna with limited data efficiency is required according to the FCC/IC regulations. This bundle has a reduced data efficiency for label/updates/hour, for more details see label product specification. 1.1 Key Features l Manages up to 10 000 imago G1 labels of all sizes l Covers up to 1 950 m (depending on shop layout) l Low power consumption powered by PoE (Power over Ethernet) or with low power plug l Easy configuration and monitoring l Optimized scheduling of tasks and self-managed roaming of labels 1.2 Destination countries The imagotag AP-2010 is currently intended for use in Europe, Canada and USA. More countries will follow. 1.3 Scope of delivery l 1 pcs imagotag AP-2010 l 1 pcs 2.4-2.5GHz 5dBi antenna l 1 pcs metal mounting l 1 pcs caddy clips 4G16M11 from Erico l 2 pcs self-locking nuts M6 May vary depending on configuration Page 4 of 27 Product Specification AP-2010 2 Barcode Information The AP-2010 comes with an AP-ID, P/N, MAC and S/N. The AP-ID consists of 5 decimal digits
(0-9). Product Code: A1A001xxx 2.1 Serial Number Depends on Producer (A) 2.1.1 Producer is 01 Part Description Format Example Comment Source Specified by imagotag once for each fab Specified by imagotag in the product specification document Fixed Incremented on every change of product specification Internal Producer Product family Product version Product revision Separator Internal Year Week 2 alpha 3 alpha 3 alpha 3 alpha 01 G1B 301 001
-
-
1 alpha 1 dec 4 B 2 dec 10 A B C D
-
E F G H I 4=2014, 5=2015,... Calendar week in current year (01-53) Calculated during production Weekday 1 dec 3 Internal 5 dec 00060 Continuous Serial Number (Counter) Page 5 of 27 Product Specification AP-2010 2.1.2 Producer is not 01 Part Description Format Example Comment A B C D
-
E F G Producer Product family Product version Product revision Separator Year Week 2 alpha 3 alpha 3 alpha 3 alpha 02 R22 N01 001
-
-
1 alpha 2 dec 13 E Internal 6 dec 000065 N = with NFC Incremented on every change of product specification E=2014, A=2010, B=2011,.. Continuous Serial Number (Counter) Source Specified by imagotag once for each fab Specified by imagotag in the product specification document Fixed Calculated during production Format:
Example:
Note:
AABBBCCCDDD-EFFGGGGGG 02G1B302001-E13000065 l Calendar week date is calculated according to ISO 8601 (see http://en.wiki-
pedia.org/wiki/ISO_week_date Page 6 of 27 Product Specification AP-2010 3 Mechanical Characteristics 3.1 Mechanical Dimensions l With antenna:
o Outline (mm): 226 x 135 x 45 o Weight: 350 g l Without antenna:
o Outline (mm): 196 x 135 x 45 o Weight: 320 g 3.2 Front, Side and Top View FIGURE 1-1: Front, side and top view of the AP-2010 1 Mounting plate fixation screw-
3 Antenna socket hole 2 LED 4 Antenna Page 7 of 27 Product Specification AP-2010 3.3 Upper Surface FIGURE 1-2: Top view of the imagotag AP-2010 5 Connection for the Power Supply 6 LAN/PoE 7 Console 8 Restart 9 Reset to Factory Settings 3.4 Side View FIGURE 1-3: Side view of the imagotag AP-2010 10 Antenna Connector (unused) 11 Warranty Seal 12 Snap Connector Housing Page 8 of 27 Product Specification AP-2010 3.5 Rear View FIGURE 1-4: Rear view of the imagotag AP-2010 13 Mounting Tab 14 Mounting Rail 15 Locking Tab 16 Label 17 Snap Connector Housing 18 Housing Screw 19 Mounting Profile Page 9 of 27 Product Specification AP-2010 4 Mounting 4.1 Audience The installation instructions are intended for trained electricians who can exhibit the following qualifications:
l Knowledge of the use of tools and work instructions. l Knowledge of the usable condition of the tool. l Knowledge of the electrical safety instructions. l Knowledge of the electrical building regulations. l Knowledge of the relevant standards. l Knowledge of assembly schedule. 4.2 General Instructions l Read these installation instruction carefully before you connect the access point to the power source. l The company imagotag GmbH assumes no liability for injury to persons or damage to the Access Point or damage to the environment caused by improper installation or mis-
application. l Remove jewellery such as rings, necklaces, and watches before working on the device. l Make sure that the access point is not connected to the power source during assembly. l Dont work on the access point during a thunderstorm and dont connect a cable at this time. l Use appropriate and tested climbing aid if you work above body height. Complete the installation and use the ERICO products just according the ERICO instruction. If necessary, you will find the desired data sheets at www.erico.com and at every ERICO customer service. 4.3 Instructions for the Mounting Location The Access Point could be mounted on a:
l Concrete wall l Mortar wall l T-Mounting Rail Select the installation location for the access point carefully. Pay particular attention to the following requirements:
l Install the access point only in areas where the permissible environmental conditions
(see ) can be observed. l Dont install the access point in environmental with direct sunlight or heat source. l Mount the metal bracket for the access point on dry surfaces only. Page 10 of 27 Product Specification AP-2010 l Dont mount the access point on any flammable material. l The minimum bearing capacity of the substrate should be 5 kg. l The LAN cable manufacturer must be complied with the default specifications (e.g. min-
imum bend radius) 4.4 Approachability l Mount the metal bracket that the access point can easily be pushed into the metal bracket l Make sure that the LAN socket is easily accessible after installation. l After installation the LED should be clearly visible. l It is important that the inner surface of the access point have sufficient air circulation. The vents must be free to ensure good ventilation and prevent overheating. The mounting material (e.g. screws or pegs) for securing the metal bracket on concrete wall is not part of the scope of delivery. It must be selected by the installer depending on the substrate itself. 4.5 Screw of the Antenna FIGURE 1-5: Figure 3 - Screw of the Antenna 1 Front Part 2 Connection Socket Note: Screw the antenna with only the front part (1) 3 Direction of Rotation 4 Rear Part (Swivelling) Page 11 of 27 Product Specification AP-2010 4.6 Metal Bracket for Mounting on Wall, Ceiling or T-Mounting Rail Once the metal bracket is mounted, the AP-2010 will be mechanical connected and fixed with a fixing screw. FIGURE 1-6: Figure 4 - Metal Bracket for imagotag AP-2010 4.7 Mounting on Wall or Ceiling FIGURE 1-7: Figure 5 - Wall or Ceiling Mounting (Scheme) 0 Mounting Surface 1 Metal Bracket 2 Mounting Screw 3 imagotag AP-2010 4 Fixation Screw a. Install the metal bracket to the wall or ceiling with the help of dowels and mounting screws. Page 12 of 27 Product Specification AP-2010 FIGURE 1-8: Figure 6 - imagotag AP-2010 Locking Tabs b. Slide the access point to the mechanical lock of the locking tabs c. Attach the AP-2010 with the enclosed fixation screw to the metal bracket 4.7.1 Mounting on a T-Mounting Rail Attach the metal bracket using the included caddy clips from Erico and the enclosed, self-
locking screw nuts M6. FIGURE 1-9: Figure 7 - Mounting an AP-2010 on a T-Mounting Rail 0 T-Mounting Rail 1 Metal Bracket 2 Self-locking Screw Nuts M6 3 imagotag AP-2010 4 Fixation Screw 5 ERICO caddy clips a. Place 2 pieces of caddy clips with the right distance on the T-Mounting Rail and fix it
(twist) Page 13 of 27 Product Specification AP-2010 b. Place the metal bracket c. Fix the Metal Bracket with 2 pieces of the self-locking screw nuts M6 d. Slide the access point to the mechanical lock of the locking tabs e. Attach the AP-2010 with the enclosed fixation screw to the metal bracket Page 14 of 27 Product Specification AP-2010 5 Electrical Specifications 5.1 Used Channels Although WIFI and ESL use the same frequency band (2.4 Ghz ISM Band), there are channels that do not overlap (not interfering - recommended channels). WLAN 1 (2402 2422 MHz) Kanal Frequenz WLAN Kanal (802.11b/g) 0 1 2 3 4 5 6 7 8 9 10 FIGURE 1-10: Overview of used channels of the imagotag AP-2010 2404 MHz 2010 MHz 2422 MHz 2425 MHz not interfering 2442 MHz WLAN 6 (2427 2447 MHz) 2445 MHz not interfering 2462 MHz 2470 MHz 2474 MHz not interfering 2477 MHz not interfering 2480 MHz not interfering WLAN 11 (2452 2472 MHz) 5.2 Difference WiFi and ESL protocol In contrast to the proprietary developed time based imagotag ESL protocol the WiFi protocol applies to the IEEE 802.11 standard. FIGURE 1-11: WiFi and ESL frequencies and channels (22 Mhz bandwidth) 5.3 Cabel Specifications You can use a commercially available LAN cable (CAT-5 or higher) for data connection and the power supply (if PoE is used) of the imagotag AP-2010. Page 15 of 27 Product Specification AP-2010 5.4 Power Supply Specifications Sunny Computer Technology Europe s.r.o. l Model: SYS1541-1505-Wxx l Input: 100-240 V ~ 1.0 A MAX, 50-60Hz l Output: 5V 3A l Output Power: 15W MAX l Operating Temperature: 0 C to + 40 C l MTBF: 50.000 hours full rated load operation at 40 , according to the MIL-HDBK-217F 5.5 Pinout RJ45 Ethernet l Pin 3 TX (AP to PC) l Pin 6 RX (PC to AP) l Pin 4/5 Ground 5.5.1 Pinout Page 16 of 27 Product Specification AP-2010 6 Electrical & RF Characteristics 6.1 General Technical characteristics Power:
l External Power Supply: 5 VDC / 3A l Power Supply via PoE: IEEE 802.3af, IEEE 802.3at l Power consumption: 15W MAX, typical 3W Technology:
l Radio technology: proprietary l Operating frequency: 2.4 GHz (ISM-Band) 2.4835 GHz l Transmitted power: 10 dBm l Number of Channels: 11 l Access protocol: proprietary Other:
l MTBF: >300.000h at 40C according to SN29500 6.2 Power and Current Consumption Power consumption measurements indicate that the AP-2010 has the following patterns:
l Operating Current: 60 mA (max. current) l Operating Power: 280 mW l Supply Voltage: 5V 10%
6.3 General Specifications 6.3.1 Hardware l 600 MHz ARM Cortex-A8 l Memory - 512MB DDR2 memory l SD/MMC card connector o 512 MB card with imagotag software preinstalled l Power over Ethernet (PoE IEEE 802.3af / IEEE 802.3at) o The original IEEE 802.3af-2003 PoE standard provides up to 15.4 W of DC power
(minimum 44 V DC and 350 mA to each device). Only 12.95 W is assured to be avail-
able at the powered device as some power is dissipated in the cable. l Other Interfaces o Serial RS232 Interface o 10/100 Ethernet Interface l Power o Power source options (DC, PoE) o 3.3 V I/O operation o DC supply 5V 10%, 3A Max Page 17 of 27 Product Specification AP-2010 6.3.2 Software Package l OS: Embedded Linux l AP-2010 application software l RF Firmware Page 18 of 27 Product Specification AP-2010 7 Environmental 7.1 Humidity and Operating Conditions l Temperature: 0 C to + 40 C l Humidity: 10% to 80% (non-condensing) 7.2 Storage Conditions l Temperature: -20 C to + 70 C l Humidity: 10% to 85% (non-condensing) 7.3 Cleaning Instructions Steps:
1. Shutdown Access Point 2. Plug Out Power Supply (AC or PoE) 3. Clean the Access Point with the help of a damp cloth Note: Do not use liquid or aerosol cleaners. Page 19 of 27 Product Specification AP-2010 8 Packing 8.1 Packing Dimensions DIMENSIONS STACKING QUANTITY LENGTH WIDTH HEIGHT BOX 520 PALLET 1200 UNIT 1200 350 800 800 260 140 960 Imagotag AP-2010 / Box: 10 8.2 Illustrations LAYER / UNIT 3 BOXES / LAYER 4 BOXES / UNIT 12 SETS / BOX 10 SETS / LAYER 40 SETS / UNIT 120 Page 20 of 27 Product Specification AP-2010 8.3 Palletization Page 21 of 27 Product Specification AP-2010 9 Certifications 9.1 Types Housing, board and the display are conform with the ROHS Directive The product meets the EU safety, health and environmental protection requirements and has the approval of CE marking This device complies with part 15 of the FCC Rules. 9.2 Overview Caption AP-2010 Food Contact RoHS CE 2 FCC/IC 5 1FCC/IC certified since calendar week 9 / year 2015 (the FCClogo must be printed on the nameplate) 2R&TTE EN 300328 V1.8.1 3R&TTE EN 300328 V1.9.1 5There are two different versions of the AP available. One CE and one FCC version. 9.3 Applied Standards Information Technology Equipment EN 60950-1/A2:2013 UL 60950-1/A2:2014 CSA CAN/CSA-C22.2 NO.60950-1-07 EMV EN 301489-17 V2.2.1 R&TTE EN 300328 V1.8.1 / EN 300328 V1.9.1 Human Exposure to Electromagnetic Fields EN 62479:2010 Radio international FCC:47 CFR Part 15 (USA) RSS-210 Issue 8 (Canada) 9.4 Declaration The company imagotag GmbH declares on his own responsibility that the AP-2010 corresponds to the standards mentioned above. 9.4.1 FCC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept Page 22 of 27 Product Specification AP-2010 any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate the equipment. 9.4.2 IC This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. 9.4.3 NCC :
Page 23 of 27 Product Specification AP-2010 10 Problems which requiring maintenance or replacement of the AP-2010 Plug out the power supply and contact the imagotag GmbH when it comes to the following cases:
l The AP-2010 was strewn with liquid. l The AP-2010 has been dropped or damaged. l The LAN port of the AP-2010 is damaged. l The antenna connection thread is damaged. l The LED of the AP-2010 no longer lights up. Contact the manufacturer if despite intended purpose the device is not working and none of the mentioned cases occurred. Page 24 of 27 Product Specification AP-2010 11 Intended Use The imagotag AP 2010 is exclusively designed to connect to electronic labels of the company imagotag GmbH via radio. The device may only be used in areas where the environmental conditions be the same as descripted in the chapter (see Environmental on page 19). Intended use includes the observance of all information in this system manual. Page 25 of 27 Product Specification AP-2010 12 Improper Use Any use that is not mentioned in Section Intended Use, shall be deemed to be improper. Any damage which result from improper use, the operator will assumes liability. The following usage is not allowed:
l Never dismantle the electronic device because except battery there is no com-
ponent which could be changed by someone who is not qualified. l Don't drop it. l Keep it away from water. l Strictly avoid direct contact with groceries. l Dont use the electronic device with defective parts. l Dont use the electronic device with spare parts and accessories which are not examined and approved by the imagotag GmbH. l Unauthorized changes or modifications to the electronic device and their com-
ponents without the consent of imagotag GmbH are not allowed. l Don't heat, recharge or bend battery. l We take no responsibility for stolen ESLs without encryption. l Keep away batteries from children. l Don't throw defective batteries into the dustbin. Give them to a reprocessing company. l Don't throw electronic device into the dustbin. Give them to a reprocessing company. l Contact imagotag GmbH for more details about this process. Page 26 of 27 Product Specification AP-2010 13 Warranty The device is provided with a warranty seal. Is this warranty seal destroyed, expire at the same time, all warranty claims. Page 27 of 27
1 | Quick start guide | Users Manual | 3.11 MiB |
Quick Start Guide Applies to software version 1.4.0 or higher Last change: 07.09.2015 Author: Kurt Haller-Walzl Quick Start Guide imagotag GmbH
[Introduction]
1 2 Electronic Shelf Labeling A brief introduction The G1 label family 2.1 Key Features 3 Whats in your Smart Box?
[Getting Started]
1 2 Latest Software and Documentation Install software 2.1 System requirements 2.2 Installation process 2.3 Customer Portal 3 Start Server and Client 3.1 Starting ESLServer 3.2 Starting ESLClient 3.3 Activating License 4 Connect and configure Access Point AP-2010 4.1 Connect and configure 4.2 Necessary configuration over the AP-2010 web management interface 4.3 Necessary configuration at the ESL Client 4.4 Selecting channels 4.5 The Status LED 5 Setup Security 5.1 General encryption features and how does it work 5.2 Set the encryption key 6 Register labels 6.1 General procedure 6.2 What's on the label?
6.3 Handheld terminals, USB barcode scanner and iOS-App 6.4 Encryption status 6.5 Unlocking labels 7 Start tagging 7.1 What can I do now?
7.2 Sending pictures to labels 7.3 Article management 7.4 Matchings 7.5 Set filters for enums Page 2 of 36 4 4 5 5 6 7 7 7 7 7 9 10 10 11 12 14 14 15 16 17 17 18 18 18 19 19 19 21 21 22 23 23 23 24 24 26 Quick Start Guide imagotag GmbH 7.5 Templates 8 Integration 8.1 Webservice integration 8.2 Plugins 8.3 Custom integration
[Troubleshooting]
1 FAQ 1.1 Running the ESLServer as a background service 1.2 Where can I find the license file for my SmartBox?
1.3 Deleting the demo articles 1.4 Establish a network configuration when no DHCP is available Step by step 1.5 AP discovering with Bonjour Services 1.6 What can I do if the Status LED of the AP-2010 access point doesnt turn blue?
1.7 Labels dont come online 1.8 The encryption does not work 1.9 Unlocking labels 1.10 Starting Java applications 1.11 Encoding problems 1.12 Further documentation 27 31 31 31 31 32 32 33 33 33 33 34 34 34 35 35 35 36 36 Page 3 of 36 Quick Start Guide imagotag GmbH
[Introduction]
1 Electronic Shelf Labeling A brief introduction An electronic shelf label is a device that shows article data and price information on its display. In comparison to printed labels the information is automatically updated if price or article data changes. l Cost reduction through elimination of manual price changes l Fully automatic price updates from the headquarters to the branch stores within seconds l Process security and price integ-
rity 100% correlation between cash point and shelf l Increased flexibility in price design and immediate reaction to market situation Image gain due to use of highly modern technology l Simplified processes for store per-
sonnel l Enhanced sales & price prof-
itability maximize price per-
formance and profit opportunities FIGURE 1-1: Electronic Shelf Labeling Page 4 of 36 Quick Start Guide imagotag GmbH 2 The G1 label family The imago G1 electronic shelf label family offers high-quality display options, operating with a replaceable battery and thus working with any external power supply. The G1 red family is capable of changing all pixels to black, white or red. The current line-up has display sizes from 2 inch to 7.4 inch. They may be used in landscape and portrait mode and can be customized with changeable front covers.
(missing or bad snippet) 2.1 Key Features l 2.4 GHz bi-directional MSK proprietary radio l Radio coverage: up to 25 meters l Return Signal: yes l 11 available communication channels l Ultra-low power consumption l Customer-replaceable battery l Full graphical e-Ink display with paper-like readability l Changeable and customizable front covers l Super wide viewing angle (nearly 180 degrees) l Flexible mounting options available l May be used in landscape and portrait mode l Fast response time (less than 15 seconds) l Water resistant l 128-bit AES encryption with secure key exchange l Multiple pages support with preloading and fast page switching l Integrated NFCtag as an option Page 5 of 36 Quick Start Guide imagotag GmbH 3 Whats in your Smart Box?
l 2x G1 2.7 Labels / 1x G1 4.4 Label o The G1 electronic shelf label family offers high-quality display options, operating with a replaceable battery and thus working with any external power supply. Thanks to the perfect readability of the e-Ink displays and our outstanding wireless data transmission technology you can implement all your sales, marketing, and logistic strategies. l 1x Access Point AP-2010 incl. Antenna o The AP-2010 by imagotag is the communication center in the store that transmits price information to the labels. Up to 10 000 labels can be managed per access point and the self-organizing network allows automatic roaming of labels without manual handling. It supports 11 selectable ESLchannels. l 1x Installation Guide with USB Stick o ESLServer: The ESLServer is a Java software that is required to manage the imag-
otag access points and electronic shelf labels. o ESLClient: The ESLClient is also Java based software. Its a graphical user interface
(GUI) for monitoring and for the configuration of the ESLServer. The ESLClient con-
nects to the ESLClient. The server may be installed on the same machine or any other machine that is accessible over the network. o Template Editor: To render images from article records on the ESLServer, the layout must be predefined in a template file. Therefor an editor to create and edit template files with live preview based on example records is also on the imagotag USB stick. o Other documentation: Developer Reference, Image Rendering Reference and CSV/XML Import Plugin l 1x Mounting Plate o Metal Mounting Plate for Mounting the AP-2010 on Walls, Ceilings or other Mounting-
Rails. l 2x Caddy Clips o With our system youre able to mount your labels almost wherever you want. l 1x Power Plug o Power Plug to supply power for the AP-2010 (Power over Ethernet is also available). Page 6 of 36 Quick Start Guide imagotag GmbH
[Getting Started]
1 Latest Software and Documentation At the Customer Portal https://portal.imagotag.com you can view all your shipments, get access to registration- and unlock codes, check the warranty status of your labels, download your license files and access the latest software releases and documentation from this site. 2 Install software Theres several software youll have to install in order to configure and setup your ESL system. Youll just have to extract the following 3 archives in a location of your choice:
1. ESL Server <server.zip>
2. ESL Client <client.zip>
3. Template Editor <template.zip>
2.1 System requirements l Server hardware: Pentium 4 (2 GHz or higher), 2 GB RAM l Java Runtime Environment Version 6, Update 36 l Windows XP, Windows 7, Windows Server 2008 (R2), Suse Enterprise Linux 11, Ubuntu 12
(all 32/64-bit versions) l imagotag Server/Client applications (2x .zip archives) l imagotag AP-2010 l imagotag Labels and license files 2.2 Installation process Please unpack the zip-archives <server.zip>, <client.zip> and <template.zip> on your machine -
e.g. under C:\imagotag\. Note: To unpack the zip-files you can either use the windows internal archive-unpacker (see screenshots) or an unpack tool of your choice (e.g. the free tool 7zip www.7zip.org). FIGURE 1-2: Unpack/Install imagotag Software FIGURE 1-3: Unpack/Install imagotag Software #2 Page 7 of 36 Quick Start Guide
#1 imagotag GmbH Page 8 of 36 Quick Start Guide imagotag GmbH After unpacking all 3 archives, your folder should look something like this:
FIGURE 1-4: Unpacked imagotag software folder The imagotag software is now installed and you can step forward to point Start Server and Client
- Start Server and Client. 2.3 Customer Portal At the Customer Portal you can view all your shipments, get access to registration- and unlock codes, check the warranty status of your labels, download your license files and access the latest software releases and documentation from this site. After user registration and activation you will have access to documentation and you can activate, manage and download your imagotag software licenses see Activating License on page 12. Your user account will not be assigned to a customer account yet. If assigned, you have access to all shipments here including lists of label IDs, registration codes and unlock codes. To get access there must be a completed order and your account needs to be verified (existing customer account required). Page 9 of 36 Quick Start Guide imagotag GmbH 3 Start Server and Client 3.1 Starting ESLServer In order to start the ESL Service with the default configuration, just execute the jar file server.jar as described in [Troubleshooting] and wait for the small service GUI to show up (if the window doesnt show up after all, make sure your Java installation and configuration is correct). FIGURE 1-5: ESLServer web management interface The service will listen to TCP connections on Port 8000 and 8001 and UDP connections on Port 8000. Please make sure that there is no firewall issue and/or interference with other systems. After start of the service you can check the web-GUI of the server:
URL: http://<host|ip>:8000 Login: admin/admin During the first start the ESLServer will automatically create a Derby1 database. If another database connection is needed or preferred, the connection parameters should be validated by imagotag. Note: As you can see there are several level numbers, by default the server instance will start in level 3. You can find the description of the different levels in the Developer Reference (which is also available at the Customer Portal) under Integration Levels. 3.1.1 Example articles For easier usage some example articles can be preloaded at the time you start the ESLServer. You can find the corresponding XMLarticle data here: C:\imagotag\server\data\fixtures\. To enable and disable the preloading of these fixtures go to the system configuration and set the corresponding property "importFixtures"true or false. Note: The article records are based on the XML-standard. 1Apache Derby, an Apache DB subproject, is an open source relational database implemented entirely in Java Page 10 of 36 Quick Start Guide imagotag GmbH 3.2 Starting ESLClient Go to the extracted client directory and execute the client.jar file. FIGURE 1-6: Starting ESL Client The client is configured to connect to a server on the local machine per default. In order to change this to a remote machine in a network you have to start the client with an additional parameter:
Windows l Create a shortcut/Edit existing short cut l Append --host hostnameOrIPAddress at the end of the Target field. (Note: The text to append starts with an space and there are 2 hyphens to add!) Linux l Append --host hostnameOrIPAddress at the end of command (e.g. java -jar client.jar -
-host 192.168.1.100 Note: The text to append starts with an space and there are 2 hyphens to add!) FIGURE 1-7: Starting ESL Client with parameter Page 11 of 36 Quick Start Guide imagotag GmbH 3.2.1 ESLClient Login l Username: admin l Password: admin FIGURE 1-8: ESLClient Login 3.3 Activating License After starting the ESLServer and Client it's necessary to activate the license which is included in the "Software License Document". To view your current license status there's a License status dialog. You can find it in the ESLClient under "Help - License status". Since no license is activated/imported yet the window should look similar to this:
FIGURE 1-9: License Status Dialog Copy the "System serial" to the clipboard and then click the "License activation". You'll be automatically redirected to the imagotag Customer Portal https://portal.imagotag.com. Please log in (or register a new user). After log in, you can see a summary of already activated licenses and / or activate a new license. Click "activate new license". Fill in "License key", copy/paste the "System serial"(from the "License Status"dialog), add a Comment (optional) and click the "Activate"button. Page 12 of 36 Quick Start Guide imagotag GmbH FIGURE 1-10: Activate License (imagotag Customer Center) Download the generated license file and complete the licensing process by importing the license file to your ESLsystem. With the successful activation of your SmartBox demo license you're now able to register and use up to five labels and one access point. FIGURE 1-11: Import of license file downloaded before Note: Press "F5"(after 15 seconds) to update the license status after license file import. Page 13 of 36 Quick Start Guide imagotag GmbH 4 Connect and configure Access Point AP-2010 The AP-2010 by imagotag is the communication center in the store that transmits price information to the labels. In order to ensure the communication between ESLServer, access point AP-2010 and the labels the access point has to be configured at the start of the ESLServer. One way to configure the access point is on the client. FIGURE 1-12: ESL Client Access Point Configuration 4.1 Connect and configure Before labels are able to communication with the server at least one access point needs to be configured. In standard configuration the AP-2010 should get an IP-address via DHCP
(recommended) and is accessible via imagotag AP-2010 web management interface:
URL: http://<host|ip>:8080 Login: admin/admin Important Note: In this part of the Quick Start Guide it is assumed that a DHCP server is present
(you can find the steps to discover the access point without DHCP in the Troubleshooting section at points Establish a network configuration when no DHCP is available Step by step and AP discovering with Bonjour Services). Page 14 of 36 Quick Start Guide imagotag GmbH 4.1.1 Discover the Access Point Before you can configure the access point its necessary that the server will discover it. The following points have to be observed:
l Connect your machine to the same network as the AP l Plug in the power supply of the access point l During the boot process of the access point, start the ESLServer software on the computer l When the access point is booted up, the server will discovery it with an IP address (Note:
The discovering process may take up to 2 minutes) l Use the ESLClient to connect to your ESLServer l Under System Access Point Status the AP should be listed as discovered (after suc-
cessful boot sequence) l One Column of the AP should show now the IP address l Now youre able to configure the access point via AP-2010 web management interface under http://<DHCP-IP-address> or a right click on the discovered AP > Open in browser In the status overview you get some details about the AP-2010:
FIGURE 1-13: AP-2010 Status overview Its recommended for the demo installation not to use the Auto-Config feature and configure the AP manually. 4.2 Necessary configuration over the AP-2010 web management interface The following actions need to be performed over the web-GUI 1. Deactivate Auto-Config: Administration -> Auto-Config 2. Set up network details (or leave DHCP): Administration -> Network 3. Set up a wireless channel: Administration -> Wireless Page 15 of 36 Quick Start Guide imagotag GmbH The AP-2010 supports 11 wireless channels. Its recommended to choose one of the recommended channels: 3, 5, 8, 9 or 10. These channels do not interfere with standard Wi-Fi channels 1, 6, 11 and are scanned by the labels more often For further information about selecting channels see point Connect and configure Access Point AP-2010. 4.3 Necessary configuration at the ESL Client After the configuration in the AP-2010 web management interface its necessary to add this AP via the ESL Client: System Access Point Configuration New FIGURE 1-14: ESL Client AP configuration - System -> Access Pont Configuration -> New Choose Manual Configuration if you dont use Auto-Config and enter Access Point ID (AP ID) and IP address (Host). Note: After the basic configuration in the AP-2010 web management interface, it is also possible to fill in AP-ID and AP-IP-Address automatically. For this choose "Create Configuration..." under System Access Point Status - Right click on the discovered and configured Access Point. After saving the AP configuration you should see the AP under System Access Point Status as ONLINE. In addition the AP status LED should turn BLUE. Page 16 of 36 Quick Start Guide imagotag GmbH 4.4 Selecting channels For a working installation a channel must be selected on each access point in the network. There are 11 non overlapping ESL channels reserved for the communication with the labels. Five of these channels do not interfere with typical Wi-Fi installations and should therefore be favored. These are the ESL channels 3, 5, 8, 9 and 10 and they should be selected if there is a Wi-Fi installation on the Wi-Fi channels 1, 6 and 11. FIGURE 1-15: Comparison between common used Wi-Fi and ESLchannels If there is a Wi-Fi installation operating at 2.4 GHz (IEEE 802.11b/g/n) or any other radio frequency (RF) technology that uses the 2.4 GHz ISM band make sure to select the ESL channels that are least overlapping with the existing installation. If there is no ESL channel without any overlapping both the ESL and existing installation should still work but there might be a reduced overall speed in both installations. Warning: Do not select the same channel on two access points within one area. This will cause interferences and avoids labels from joining the network. The same channel may only be selected on two access points if it can be guaranteed that every label is within the range of only one of these access points. 4.5 The Status LED There are several LED colors that indicates the main status of the access point. Color Description Red Blue Yellow Boot process Normal mode Operational, but not connected to any server or no channel selected Note Can take about 2 minutes, if it takes much longer, the device is defective and there is a need for service.
---
---
Red (blinking) Running Firmware Update During this time there is no connection to the electronic label If there are any problems regarding the access point please see chapter [Troubleshooting]. Page 17 of 36 Quick Start Guide imagotag GmbH 5 Setup Security The security concept is based on individual registration codes for each label. Not only that the new concept simplifies installations, it also provides stronger encryption and a secure key exchange with individual communication key derived from a user defined network key. 5.1 General encryption features and how does it work l Solid improved safety l Encrypted data type AES128 (Advanced Encryption Standard) l User defined 128 bit network key for each installation l Key is distributed to labels automatically The new system requires a user defined 128 bit network key for each installation. The key is derived from a passphrase that is defined by the customer and stored in the ESLServer and used by all access points connected to that server to encrypt data communication to the labels. A per-label communication key is transmitted to the labels during the registration of them. Each label is assigned an individual registration code (it combines label ID and PIN code and its an alphanumeric case-sensitive code with 11 characters). The ESLServer will than automatically start the key exchange with the label secured by the PIN extracted from the registration code. 5.2 Set the encryption key First step is to set the parameter encryptionPassphrase under System Configuration (you can choose the encryption Passphrase on your own). FIGURE 1-16: Set encryption key Note: Do not change encryption passphrase if labels are already connected and encrypted (if you want to change the encryption passphrase youll first have to unlock all labels see
[Troubleshooting] on page 32). Page 18 of 36 Quick Start Guide imagotag GmbH 6 Register labels In order that labels can join the network it is necessary to register them first. 6.1 General procedure Via the ESL Client under File Register Labels its possible to register your labels manually with the registration code shown on each single label or you could import a CSV file with your registration codes. In order to refresh the entries press the refresh button shown in the next figure. Important Note: After the registration it could last a certain time until all registered labels are joined to the network (from 30 minutes up to two hours, depending on configured access point channels). After this you can send images to each label (see Start tagging on page 23). FIGURE 1-17: Add/Delete Label and refresh entries 6.2 What's on the label?
All labels will arrive with its registration code (11-digit alphanumeric)shown on the display of the label. The code is printed as a 2D QR code, as a 1D Code128 barcode and as human readable text. The registration process for the customer is easy he has only to scan one of this barcodes. The ESLServer will than automatically start the key exchange with the label secured by the PIN extracted from the registration code. The two relevant codes:
1. The label ID (8-digit hexadecimal) to identify the label (it's also the radio address which is similar to a MAC address). 2. The registration code (11-digit alphanumeric) is required to activate the encryption. This code also contains the label ID and a random PIN code. Page 19 of 36 Quick Start Guide imagotag GmbH 6.2.1 Labels before and after registration Page Layouts G1 4.4 Layout when shipped Registration Page Layout Note:The label ID can only be read and will not be displayed as barcode in this layout. Layout after successful registration Reset Page Layout Note: After successful registration, the AES key is exchanged for encryption and the label switch to a page where only the label ID is displayed as 1D Code128 barcode. The sticker (on the bottom and on the back) always contain only the label ID and therefore should not be used for registration. They are only intended for the later article assignment (matching process). Here you can see the registration dialog in the ESLClient where one single label has been entered with the registration code and the other one with the label ID (for old label versions < 3.0.0). FIGURE 1-18: Register labels dialog (registered with registration code and label ID) Page 20 of 36 Quick Start Guide imagotag GmbH Note: New versions of the ESLServer, ESLClient and AP-2010 ( 1.3.0) will also support old labels that do not come with a pre-programmed PIN code. New labels ( 3.0.0) will also work in old installations together with old labels but the ESLServer will not accept registration codes during the registration process. To register the labels it is required to scan the barcode with the label ID from the backside or the bottom edge of the label. As the server will not start the key exchange all data is transmitted unencrypted to the labels. 6.3 Handheld terminals, USB barcode scanner and iOS-App Its also possible to register labels with a commercial USB barcode scanner (2D/1D). You can also use our iOS-App (for iPhone and iPod touch, only available on request). Handheld terminals are mobile devices that are used to manage the ESL installation. If the handheld provides a barcode scanner, it may be used easily to link articles and labels by scanning the article barcode (usually EAN, UPC or GTIN) and the unique ID of the label. Here you can see some screenshots of our iOS-App:
FIGURE 1-19: ESL-App Home-
Screen FIGURE 1-20: ESL-App Registration Page FIGURE 1-21: ESL-App Matching Page 6.4 Encryption status Here are the encryption status a label could have:
l AES: Communication with label is encrypted with 128 bit AES l No PIN: Could not set encryption key as no PIN (registration code) was provided o Solution: Re-register label with registration code l Keyunset: Communication is NOT yet encrypted o Solution: Set encryption key as described in section Setup Security - Setup Security l Unsupported: Encryption is not supported by label firmware l Unknown: Security status is not determined yet Page 21 of 36 Quick Start Guide imagotag GmbH FIGURE 1-22: Encryption status 6.5 Unlocking labels If the label was registered and a communication key was set it will no longer work in other networks using a different network key passphrase. To unlock this labels for other networks an unlock code is required. The unlock code is similar to the registration code - it is a combination of the label ID and a 128 bit PUK code. Via ESLClientselect File Unlock labels and enter the unlock key. FIGURE 1-23: Unlock Labels Dialog Note: The unlock-code for the specific labels is enclosed in the Smart Box (in an envelope). Page 22 of 36 Quick Start Guide imagotag GmbH 7 Start tagging 7.1 What can I do now?
As soon as labels are online you can do several things:
l Send image to label l Assign tags l Show the current image l Ping label l Reset label (reset display to show label ID and label ID barcode) l Refresh display l Switch to a preloaded page l Create a new matching l Set filters l 7.2 Sending pictures to labels 1. Right click on one or more labels -> Send image 2. Select a picture (Note: Display size must match the resolution of the image) A. In the right pane, a priority (currently not relevant) could be set for the task, as well as the Page to which the image should be sent and whether the image is preloaded. B. When preloading, the image is placed in the memory of the label, but not yet dis-
played. The image change will only be performed after the change to the relevant page. This allows for each label that images are cached on the various pages and be accessed quickly by switching to the relevant page. 3. By clicking on open the corresponding task(s) for the label(s) will be created and the transfer begins. FIGURE 1-24: Send image to label Page 23 of 36 Quick Start Guide imagotag GmbH 7.3 Article management For complete management of your articles select Articles All Articles in the ESLClient. Here youre able to create/delete and edit your articles. The Smart Box comes with 4 predefined articles which you can see here. You can add some more demo articles, edit the existing ones or just step further to the next point Matchings. FIGURE 1-25: Article management 7.4 Matchings The logical link between an article and the label that shows the article information and price of this article is called matching. With a matching the layout of the image rendered for the label is also defined by specifying the name of a template. In a more technical way a matching is the triple of:
l Label ID l Article number or GTIN l Name of the template file Note: Only one matching per label is allowed but a single article may be matched to more than one label. Select File New matchings to open the dialog where you can select the desired data records and create a number of matchings at the same time. Page 24 of 36 Quick Start Guide imagotag GmbH FIGURE 1-26: New matchings dialog Another way to create/edit matchings is under Matchings All Matchings:
l Select the desired data records (Label ID, Article Number) in the following window New Matching Record (either manually or with the magnifying glass symbol). Select an appro-
priate template via Template that should be used to generate the image. l Confirm your choice by clicking Save. After that, the generated image is sent to the selec-
ted label. FIGURE 1-27: Create a matching Page 25 of 36 Quick Start Guide imagotag GmbH Its also possible to create Matchings with ESLClient under Labels and Articles, for this just select the desired article or label, right-click on it and select New matching (the new matching dialog will be pre-filled with the article or label information). 7.5 Set filters for enums It's possible to set and combine several filters. Click on the drop down menu to see the different choices. FIGURE 1-28: ESLClient filter options 7.5.1 Filter options The following operators are available:
Operator Description Less than Greater than Less than and equal Greater than and equal Negation (Not) Equals Defines a range (e.g. RSSIfilter -65:-75 shows all labels with current RSSIvalue within -65 and -75) Doesn't apply to date and text.
<
>
<=
>=
!
=
:
Page 26 of 36 Quick Start Guide 7.5 Templates imagotag GmbH The template is used to specify the fields, which should be rendered into the image. The ESLServer can handle multiple templates. 7.5.1 General information about templates The image rendering process is based on XSL (EXtensible Stylesheet Language) templates. The individual image for the label is then generated by applying the template to a XML, which is based on the properties of the label and is expanded by a custom XML from the user. The following steps are executed when processing a template:
l Generating a record XML based on the label/task information and custom information provided by the user l Applying the template (XSL) on the generated record XML. This results in a document con-
taining the fields, specified in this reference and values referenced from the XML l Rendering the image (*.PNG) based on the previous output FIGURE 1-29: Input and result of the rendering process 7.5.2 Template Editor In order to use our rendering engine you must know our template language which is basically XSL. We do also have a Template Editor with live preview, but you need a little bit time to setup everything and get familiar with it. Therefore we suggest to send pre-rendered images to labels
(right-click on a label -> send image) which you can create with every image manipulation software you want (e.g. Gimp, Photoshop, Paint, ). You can even take some pre-rendered images from us for each label type with the correct resolution as a template youll find some in the clients directory under data/images. Page 27 of 36 Quick Start Guide imagotag GmbH 7.5.2.1 Starting Template Editor Navigate to the unpacked template directory (see point Installation process on how to unpack the software package) and execute the template.jar file (see [Troubleshooting] on page 32). FIGURE 1-30: Starting the Template Editor 7.5.2.2 Open default template-file and load records from server:
l Open the Template Editor by clicking the template.jar file located in the template-dir-
ectory (In our example it should be C:\imagotag\teamplate\). l Next step is to create a new template file or to open an existing one (The default.xsl tem-
plate file is located in the server-directory under C:\imagotag\server\data\template\). l To get a live preview youll have to load some records, in our case we load the demo article records from our running server, see the following figure. FIGURE 1-31: Load Records from Server Page 28 of 36 Quick Start Guide imagotag GmbH After these steps your Template Editor window should look something like this:
FIGURE 1-32: Template Editor with loaded records from server and default.xsl template file 7.5.2.3 Design Mode You can enable the graphical Template Editor by selecting Settings Configuration tick Enable Design Mode and finally the Save-button. FIGURE 1-33: Enable Design Mode in Template Editor Page 29 of 36 Quick Start Guide imagotag GmbH After enabling the Design Mode a new tab will show up. FIGURE 1-34: Template Editor Design Tab 7.5.2.4 Enable and show color red As there are new label types which are capable of showing the color "red"there's a short description how to enable this inside the xsl template file. l Optional: Query whether it is a "red" label l <xsl:when test="Label/DisplayWidth = XXX and Label/DisplayHeight = XXX and Label/DisplayColors = 'BLACK_WHITE_RED'">
l Add colors option to image tag:
l <image width="XXX" height="XXX" colors="true" font-family="XXX">
l Show something in color red, e.g. text:
l <text font-size="XXX" condense="XXX" font-weight="XXX" color=red>
7.5.2.5 Help Content Theres a link to the Help content for the Template Editor, open it by clicking Help Help Content in the Template Editor or open the file index.html located in C:\imagotag\template\help\. Also you can find further information on the USB Stick under Documentation - Image Rendering Reference. Page 30 of 36 Quick Start Guide 8 Integration 8.1 Webservice integration imagotag GmbH The ESL server provides access to its interfaces methods through a RESTful web service API. The web service is designed according to the Representational State Transfer (REST) architectural pattern. The ESL server listens for incoming HTTP web service requests on the TCP port 8001 by default. You can find further information and documentation about the webservice integration online under https://portal.imagotag.com/get/documentation 8.2 Plugins We provide several plug ins which are used for importing article information into the ESL Server. You can find further information and documentation about our integration plug ins online under https://portal.imagotag.com/get/documentation 8.3 Custom integration For custom integration we provide a Plugin-Interface. Software development service is available from imagotag software development team or third-party integration partners. For pricing get in touch with our sales agents (sales@imagotag.com). Page 31 of 36 Quick Start Guide imagotag GmbH
[Troubleshooting]
FAQ 1 If you run into any errors during connecting or sending images to labels, please refer to the documentation included in the server. This documentation can be found in the AP-2010 web management interface of the server under Documentation. l For problems updating the labels (error code column in labels window) refer to Update Error Codes or (task status column in labels window) refer to Task Status l For connection status problems refer to Connection Status l For label hardware errors (label error column in labels window) refer to Label Error Codes Code Problem 1 3 10 11 12 13 14 20 21 22 30 62 80 92 Label not licensed Label not registered Image does not match display size Error during image rendering Error during image conversion Invalid page Could not process task because there are unfinished tasks waiting for this label Template not found Error during template parsing Error during content document creation Could not send update because label has insufficient power to perform the update HTTP communication error with the access point Error while writing task to database Task type not supported Solution The label is not licensed. Import the proper license file for the label or check for typos in the label id. The label may have been deleted or has never been registered at all. Register label. The size of the image does not match the labels display size. Please check the width and height of your image and look up the display size in pixels for the label. These sizes have to be equal. Check template (wrong or faulty) Change format of the image to standard format
(e.g. PNG or BMP) Page not supported by label type, choose a different page Abort task or wait until unfinished tasks are finished Check template directory for missing template file Correct template file (Invalid content found) Check server and article record configuration The power status of the label is Bad, which means it is very low on battery that in may not accomplish the display update. Replace the battery of the label. The server was not able to send the task to the Access Point. Please make sure that the Access Point is not offline (System -> Access Point Status) and there is an established network connection between Access Point and Server. Check database connection Upgrade AP software to process this kind of task Page 32 of 36 Quick Start Guide imagotag GmbH 1.1 Running the ESLServer as a background service The ESL server may be started as a normal application, but on a productive system it is usually required to have it automatically started without a user logged in. To achieve this the ESL server can be registered as a Windows service. It is than started automatically without any graphics user interface. To install the ESL server as a Windows service the batch file install_service.bat is provided. If this file is executed with administrator privileges (Right click Run as Administrator) it will install the ESL server installation from the same directory as a Windows service with the name ESL_ SERVICE. The file uninstall_service.bat will remove the Windows service if executed with administrator privileges. If you have any problems regarding the background service:
l Check if you have installed the correct JAVAversion corresponding to your system
(x86/x64) l If the ESLServer is already installed as a Windows service you have to uninstall it first (unin-
stall_service.bat) and reinstall it again (install_service.bat). 1.2 Where can I find the license file for my SmartBox?
You find the license file (which has to be activated at the imagotag Customer Portal enclosed in the SmartBox in a "License Envelope". 1.3 Deleting the demo articles In order to prevent the example articles from being re-added to the server, go to "System -
Configuration"and set the "importFixtures"variable to false. 1.4 Establish a network configuration when no DHCP is available Step by step 1. Set a laptops Ethernet adapter to DHCP 2. Turn off all other network adapters (Wi-Fi) 3. Connect to the same network as the AP-2010 (use a common Ethernet cable to connect your device directly with the AP-2010) 4. Start local ESL Server on laptop 5. Use the ESL client to connect to your local server 6. Under System Access Point Status the AP should be listed as discovered (after suc-
cessful boot sequence may take up to 2 minutes) l Press F5 on your keyboard or the refresh button in the ESL client to refresh the access point status (the Client doesnt refresh the status automatically!) 7. One Column of the AP should now show the IP address 8. Open a browser, type in http://<discovered-ip>:8080 or l at the ESL client perform a right click on the discovered access point Open in browser Maintenance Status Note: Restart your access point if discovering process takes more than 2 minutes. Page 33 of 36 Quick Start Guide imagotag GmbH FIGURE 1-35: Restart and Factory Defaults button 1.5 AP discovering with Bonjour Services You still got problems to find your AP in your network? There's another workaround: You can use Apple's "Bonjour Print Services". Download and install Bonjour Print Services for Windows (pre-installed under OSX):
http://support.apple.com/kb/DL999 Note: After installation theres no reboot required. If the access point is connected directly to the system where the Bonjour Service is installed
(or on a network with running Bonjour Service) you can find the access point by typing the following in the browser of your choice:
http://ap-<ID>.local:8080 (e.g. http://ap-12724.local:8080) Note: You can reach older versions of the AP with http://imagotag-ap.local:8080 (custom hostnames are only available on newer versions of the access point) 1.6 What can I do if the Status LED of the AP-2010 access point doesnt turn blue?
l Check the AP status l Check AP configuration o No Channel set l Check network reachability of AP l AP registered to Server?
l Reboot AP 1.7 Labels dont come online After the registration it could last a certain time until all registered labels are joined to the network (up to two hours, depending on number of access points and the channels used. l Up to 30 minutes with channels 3, 5, 8, 9 and 10 l Up to 2 hours with channels 0, 1, 2, 4, 6 and 7 Warning: A label must not be registered to multiple ESL server installations at the same time. It will only connect to one of this installations. Page 34 of 36 Quick Start Guide imagotag GmbH 1.8 The encryption does not work Check the encryption passphrase in Server Configuration (System Configuration). If label was already registered with a different passphrase youll have to unlock the label first in order to register it on the server. 1.9 Unlocking labels If the label was registered and a communication key was set it will no longer work in other networks using a different network key passphrase. To unlock this labels for other networks an unlock code is required. Select File Unlock labels and enter the unlock key. The unlock-code for the specific labels is enclosed in the Smart Box (in an envelope). If you have any problems (the unlock code wasn't included or you can't find it) please contact the imagotag support (support@imagotag.com). 1.10 Starting Java applications Before starting a Java application, make sure you have Java Runtime Environment Version 6 or higher installed and you have set the necessary environment variables. If the .jar file extension is known and associated with Java, just double-click the jar file to start the application. Otherwise if the extension is not recognized:
Windows:
Create a shortcut of the jar file, right-click on it and open properties. Prepend javaw.exe jar to the path in the Target field. Double-click the shortcut. Linux:
Navigate via command line to the directory where the jar file lies and execute java jar
<filename>.jar In case your environment variables are not set properly (e.g. javaw.exe/java command could not be found) do the following steps:
1. Locate your installation directory of your Java Runtime Environment 2. Set JAVA_HOME Variable Under Windows:
l Right-click on My Computer and select Properties l Click the advanced tab l Click the EnvironmentVariables button l Under SystemVariables, click New. l Enter the variable name as JAVA_HOME l Enter the variable value as the installation directory of your Java Runtime Environment l Click OK l Look for the Path variable in SystemVariables and edit it l Append a semicolon (;) and %JAVA_HOME%\bin to it Page 35 of 36 Quick Start Guide imagotag GmbH l Click OK l ApplyChanges Under Linux:
l Use the export command to set your variables l export JAVA_HOME=<pathToJRE>
l export PATH=$PATH:<pathToJRE>/bin l In order to make these changes persistent, write them into your .bash_profile file and use source ~/.bash_profile to apply the changes 1.11 Encoding problems Per default, UTF-8 encoding is used. If you have any problems regarding encoding you can force any java application to use UTF-8. By setting the (Windows) environment variable JAVA_TOOL_ OPTIONS to -Dfile.encoding=UTF8, the (Java) System property will be set automatically every time a JVM is started. 1.12 Further documentation Please contact the support for further documentation:
l Developer Reference (Web Service) l Image Rendering Reference l CSV/XML Import Plugin l FAQ Page 36 of 36
1 | Label | ID Label/Location Info | 369.84 KiB |
AP-2010 sesimagotag I/P 5V=== 3A or PoE (IEEE 802.3af) Frequency 2.4 GHz C Se MFD: 17-07, Rev. 9 ap-ip: 20142 fay UUUIUOAUIN A Co Model: A02 7 IC: 12154A-AP0002 Product Code: A1A001210 NIAV. UCIT AAA A 68:9e:19:93:e3:b1 a 04A1A001309-G430005501
1 | Label placement photo | ID Label/Location Info | 805.71 KiB |
Appendix 2 Photodocumentation Description: Backside view Division:
Industry & Energy Department: FG Test report reference:
INE-AT/FG-17/101 Page: 2 of 11 Date: 06.04.2017 checked by: _______
1 | Cover Letter | Cover Letter(s) | 39.65 KiB |
Coverletter:
imagotag GmbH wants to get FCC-Certification for the following product:
digital network controller device A02. The unit will get the following FCC-ID: 2ACQM-AP0002 List of documents:
Thema File Label and placement Label.pdf Not needed Exhibit 02 Exhibit 03 External Photos
* Exhibit 04 Block Diagrams
* Exhibit 05 Schematic Diagrams RFACP001C00C_Schematics.pdf Label placement.pdf
extern_17-101.pdf Blockdiagram.pdf Exhibit Exhibit 01 Exhibit 06 Exhibit 07 Exhibit 08 Testreport Test Set-up Photos User Manual Internal Photos Informations RF exposure Exhibit 09 Exhibit 10 Exhibit 11
* Exhibit 12 Operational Description Cover letter Request for confidentiality Exhibit 13 MS_IM_AP_SCH_REVC.pdf FG17-101.pdf setup_17-101.pdf it_prod-spec_AP-2010-FCC-public.pdf QuickStartGuide.pdf intern_17-101.pdf
FCC Protocol Timing Specification.pdf it_prod-spec_AP-2010-FCC-private.pdf This file Confidentiality Request_FCC_201703_signed.pdf For the Exhibits marked with * imagotag GmbH requested Confidentiality according to 47 CFR 0.457 and 0.459 of the FCC rules because these are sensitive parts owned by this company and include much of Know-How or sensitive data, it will not be provided to the public. The labelling on some photos may be not the actual status. The correct labelling you can see on the label photo in Exhibit 1.
1 | Request for Confidentiality | Cover Letter(s) | 67.43 KiB |
ONFID NTIALITY REQ E Page 1/2 C Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 March 27, 2017 TO WHOM IT MAY CONCERN Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, imagotag GmbH (FRN: 0023782022) requests confidentiality for the following products:
FCC ID Number Product: Title/Model Product Code: A1A0012xx o FCC ID: 2ACQM-AP0002 For the product stated above, we request that the following information be held confidential Circuit diagrams, BOM; and PCBs submitted as Equipment Authorization Electronic Filing attachment: folder: Hardware Block diagram, Operational description submitted as Equipment Authorization Electronic Filing attachment:
it_prod-spec_AP-2010-FCC-private.pdf The above exhibits contain SES-imagotag GmbH trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our Smart Tagging System. This material is not customarily available to the general public and we request that it be withheld from public inspection. If you have any questions, please feel free to contact me at the address shown below. STA k lA Philipp Maurer, BSc MA Project Manager R&D SES-imagotag GmbH St. Peter Giirtel 10b 8042 Graz, Austria Phone: +43 (0)5 9809-400 Mobil: +43 664 889 294 11 philipp.maurer@ses-imagotag.com www.ses-imagotag.com
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2017-04-13 | 2404 ~ 2479.25 | DXT - Part 15 Low Power Transceiver, Rx Verified | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2017-04-13
|
||||
1 | Applicant's complete, legal business name |
SES-imagotag GmbH
|
||||
1 | FCC Registration Number (FRN) |
0024111486
|
||||
1 | Physical Address |
Kalsdorfer Strasse 12
|
||||
1 |
Fernitz-Mellach, 8072
|
|||||
1 |
Austria
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
a******@tuv.at
|
||||
1 | TCB Scope |
A2: Low Power Transmitters (except Spread Spectrum) and radar detectors operating above 1 GHz
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
2ACQM
|
||||
1 | Equipment Product Code |
AP0002
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
P****** M******
|
||||
1 | Telephone Number |
00435******** Extension:
|
||||
1 | Fax Number |
00435********
|
||||
1 |
p******@ses-imagotag.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DXT - Part 15 Low Power Transceiver, Rx Verified | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | digital network controller transceiver | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
TUV AUSTRIA SERVICES GMBH
|
||||
1 | Name |
W******** S******
|
||||
1 | Telephone Number |
43-1-********
|
||||
1 | Fax Number |
43-1-********
|
||||
1 |
e******@tuv.at
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2404.00000000 | 2479.25000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC