Bluetooth Thermometer Temcerature is Evervthina!
M delNo.: BTH02 Instruction Congratulations thermometer. inside your grill, You will now be able t oven or smokefromyour sma m on your purch eof the Professional nitorthe temperatu motelym biledevices. Smart Food Thermometer, an APP suppodfood food and the temperatu fcooking mpnents c 1. One smart thermometer magnet base. 2. One universal 3.Tw steel detachablestainless unit. probes with steel mesh cable. 4. Three AAA baeries. Features 1.LCD display 2.On/OFF 3.Taimer+
4.Taimer-
5.Battery Compartment LCD Screen Probe1 1. Current temperatu e Probe 1 2. Tatemperatu 3. Current temperature Probe 2 4. Target temperatu 5.me1 6. Timer2 Probe2
<:=) Unit Turn On/i ON-Press 3 seconds to turn ON the smadevice. OFF-P ss3 seconds to turn OFF the smadevice. nenessmperaturerange Measure meatmperatu toUSDA d Set from APP 1. Tape the Probe 1 2.Sel t m ttype BEEF, Lamb, Pork, Turkey, 3. Choose Gourmet or USDA standard 4. Once the temperature n. rProbe 2 meat setting ic Fishc. Press any bu nto st temperature, then the taettemperature nenesslevel, will be send to smart device. the smadevicewill beep. of meat Probe 1 or Probe 2 achesthe d pthe beep. cC
@
26 176 0 OC:00.00 r Set from device 1.You can use two probes (Probe 1 and Probe 2) to measu andmonitor temperatu sof two pieces of meat or tw ti ns fthe same laepiece of meat at the same time. 2.Pe ssMODE to select Probe 1 or Probe 2, then press + -to choose your taet temperature. Leave it for 2 seconds, w 3. Once the tem:tufmeat Probe 1 or Probe 2 reaches will be sautomatically temperature the target and sh nthe display. the doneness level, the smart device will beep. Press any bu n t st pthe beep. Count d wnTin er 1. Ch seTimer 1 or Timer 2, P 2.If you need to set up very long timer count down timer, Id+t 3. Leave the button for 2 sec 4. When countdown timer Note: Smart Device count down timer is paratedwith APP Timer just to avoid the confict. youradjust timer setting. h nds,the Timer will be set automatically. aches0 , an alarm will beep. P It suppo999minutes. pthe beep. increase s+t s ssany bu ntost and press -to deduct. pre t rkingcondition, wer.If not necessary, Backlight In w of p Helpful 1. Do not immerse the probe in water while cleaning. 2.D 3. D 4. Avoid probe touching notuse malprobe in Microwave notallow the probe or probe wire to contact rheavy fat areas.It turnon backlight nis to turn mmendati the rec Hints oven. bone and -t turnoff backlight. Using the backlight will tupa I t backlight. with flames. might usetermp .tu displayseems increase too fast. notexpose the receiver or transmitter di ctheat. Cauns:
1. D 2. Kp the stainless 3. D 4.D 5. D steel probe sensor and wires away from childI . gl nottouch the hot probe with bare hands. Wear a heat resistant vetoduring notuse in the rain. Smart Device is not waterproofed. notimmerse the probe in water while cleaning t r arc king. Ousingdish washer to clean probe. Clean them with damp cloth. NE-YEARWARRANTY LIMITED Cappecwar ntsthis product to beeof defects in pamaterials rkmanship from date of purchase. Sh tions on how to pack and ship the product to Cappec. iswar ntygives y under this warranty be required, uldany repairs or servicing and you may also have uspecific legal rights Customer therrights contact and w for a peri dof neyear, Service by email for instruc which vary fromateto state. Customer Service:
Email: SUDDrt@cacoec.cm FCC Warning:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement. Th e device can be used in portable exposure condition without restriction.