Contactless Door Egress Device (US Standard) Design Philosophy Match OEM reader design in order to maximize the marketing value at the door. Abbreviation REX2-e Economic Request to Exit button. Basic model without chimer and sirens. REX2-i Intelligent Request to Exit button. Model with chimer and sirens. REX2-s Safety Request to Exit Device. Model with Break Glass function. Technology & Function Capacitance Proximity Technology has been used instead of Infar-red technology environmental independent design. When the device is activated, indicator light will change color with an audible tone very user friendly. Icon indicators to alert the user for Door Held Open, Fire Alarm and Mains Failure situation. Build-in Mechanical Override in case power failure or electronic failure. Build-in Door Chimer to interact with the * sign on Magic series Number pad reader. Build-in Fire Alarm input. If the fire input got trigger, the lock will be released automatically. Embedded a traditional Break Glass device with test key. When activated, both Visible and Auditable alert will trigger to provide better indication of the door location under emergency situation. Support Remote Control (433MHz) to trigger the REX remotely. Friendly Installation All inputs are 12Vdc protected. protected against static Reverse power protection. All input and output signals are charges. Specification:
Model Functions Functional Specification Request to Exit indication Request to Exit output REX2-i REX2-s Color changes from Blue to Green with a beep Dry contact output for 1 seconds (NC/NO selectable) RTE Output (dry contact) NC/NO jumper selectable rated @ 30Vdc; 1A Mechanical Override Tamper protection Remote Button (Optional) Alarm Output Door Held Open Indication icon Door Held Open High/Low level input jumper Buzzer for DHO and RTE activate Main Power failure Indicator Fire Alarm Indicator Fire Alarm Input Speaker Available for all models Available for all models 433.896MHz
(Max supports 5 remote buttons at the same time.) Dry contact output follow the Fire input (NC/NO selectable) The icon will change to blue and beep every 5 seconds High/Low level input jumper selectable Jumper enable/disable Mains failure dry contact output from Power Supply. The icon will change to orange when activated The icon will change to red and siren will activated When trigger, back lit will flash in Red the siren will When trigger, the lock will release and back activate lit will flash in Red & siren will activate Equipped for Door Chimer and Siren Break Glass function N/A Hit hard at the center Dimension 118.2 (L) X 74.2 (W) X 8.5 (H) mm (above surface) Technical Specifications Typical Read range
~3 to 4cm Electric Lock bypass relay N/A 30Vdc; 2A (max) Electric Box Requirement Weight Please make sure the gang box is similar to the diagram as display. 157g Operating Specification:
Operating Voltage 9 - 15VDC Case material Operating Current 150mA (max @ 12Vdc) Standard Color Operating Temperature
-20-60 Operating Humidity PC+ABS Black & White 10% - 90%
FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.